5ba444f092
Add NAND partition table, EK board support boot up NAND flash using the same NAND partition table Add Index in this file Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
175 lines
5.8 KiB
Plaintext
175 lines
5.8 KiB
Plaintext
Atmel AT91 Evaluation kits
|
|
|
|
Index
|
|
- I. Board mapping & boot media
|
|
- II. NAND partition table
|
|
- III. watchdog support
|
|
|
|
I. Board mapping & boot media
|
|
------------------------------------------------------------------------------
|
|
AT91SAM9260EK, AT91SAM9G20EK & AT91SAM9XEEK
|
|
------------------------------------------------------------------------------
|
|
|
|
Memory map
|
|
0x20000000 - 23FFFFFF SDRAM (64 MB)
|
|
0xC0000000 - Cxxxxxxx Atmel Dataflash card (J13)
|
|
0xD0000000 - D07FFFFF Soldered Atmel Dataflash (AT45DB642)
|
|
|
|
Environment variables
|
|
|
|
U-Boot environment variables can be stored at different places:
|
|
- Dataflash on SPI chip select 1 (default)
|
|
- Dataflash on SPI chip select 0 (dataflash card)
|
|
- Nand flash.
|
|
|
|
You can choose your storage location at config step (here for at91sam9260ek) :
|
|
make at91sam9260ek_nandflash_config - use nand flash
|
|
make at91sam9260ek_dataflash_cs0_config - use data flash (spi cs0)
|
|
make at91sam9260ek_dataflash_cs1_config - use data flash (spi cs1)
|
|
|
|
|
|
------------------------------------------------------------------------------
|
|
AT91SAM9261EK, AT91SAM9G10EK
|
|
------------------------------------------------------------------------------
|
|
|
|
Memory map
|
|
0x20000000 - 23FFFFFF SDRAM (64 MB)
|
|
0xC0000000 - C07FFFFF Soldered Atmel Dataflash (AT45DB642)
|
|
0xD0000000 - Dxxxxxxx Atmel Dataflash card (J22)
|
|
|
|
Environment variables
|
|
|
|
U-Boot environment variables can be stored at different places:
|
|
- Dataflash on SPI chip select 0 (default)
|
|
- Dataflash on SPI chip select 3 (dataflash card)
|
|
- Nand flash.
|
|
|
|
You can choose your storage location at config step (here for at91sam9260ek) :
|
|
make at91sam9261ek_nandflash_config - use nand flash
|
|
make at91sam9261ek_dataflash_cs0_config - use data flash (spi cs0)
|
|
make at91sam9261ek_dataflash_cs3_config - use data flash (spi cs3)
|
|
|
|
|
|
------------------------------------------------------------------------------
|
|
AT91SAM9263EK
|
|
------------------------------------------------------------------------------
|
|
|
|
Memory map
|
|
0x20000000 - 23FFFFFF SDRAM (64 MB)
|
|
0xC0000000 - Cxxxxxxx Atmel Dataflash card (J9)
|
|
|
|
Environment variables
|
|
|
|
U-Boot environment variables can be stored at different places:
|
|
- Dataflash on SPI chip select 0 (dataflash card)
|
|
- Nand flash.
|
|
- Nor flash (not populate by default)
|
|
|
|
You can choose your storage location at config step (here for at91sam9260ek) :
|
|
make at91sam9263ek_nandflash_config - use nand flash
|
|
make at91sam9263ek_dataflash_cs0_config - use data flash (spi cs0)
|
|
make at91sam9263ek_norflash_config - use nor flash
|
|
|
|
You can choose to boot directly from U-Boot at config step
|
|
make at91sam9263ek_norflash_boot_config - boot from nor flash
|
|
|
|
|
|
------------------------------------------------------------------------------
|
|
AT91SAM9M10G45EK
|
|
------------------------------------------------------------------------------
|
|
|
|
Memory map
|
|
0x70000000 - 77FFFFFF SDRAM (128 MB)
|
|
|
|
Environment variables
|
|
|
|
U-Boot environment variables can be stored at different places:
|
|
- Nand flash.
|
|
|
|
You can choose your storage location at config step (here for at91sam9m10g45ek) :
|
|
make at91sam9m10g45ek_nandflash_config - use nand flash
|
|
|
|
|
|
------------------------------------------------------------------------------
|
|
AT91SAM9RLEK
|
|
------------------------------------------------------------------------------
|
|
|
|
Memory map
|
|
0x20000000 - 23FFFFFF SDRAM (64 MB)
|
|
0xC0000000 - C07FFFFF Soldered Atmel Dataflash (AT45DB642)
|
|
|
|
Environment variables
|
|
|
|
U-Boot environment variables can be stored at different places:
|
|
- Dataflash on SPI chip select 0
|
|
- Nand flash.
|
|
|
|
You can choose your storage location at config step (here for at91sam9rlek) :
|
|
make at91sam9rlek_nandflash_config - use nand flash
|
|
|
|
|
|
------------------------------------------------------------------------------
|
|
AT91SAM9N12EK, AT91SAM9X5EK
|
|
------------------------------------------------------------------------------
|
|
|
|
Memory map
|
|
0x20000000 - 27FFFFFF SDRAM (128 MB)
|
|
|
|
Environment variables
|
|
|
|
U-Boot environment variables can be stored at different places:
|
|
- Nand flash.
|
|
- SD/MMC card
|
|
- Serialflash/Dataflash on SPI chip select 0
|
|
|
|
You can choose your storage location at config step (here for at91sam9x5ek) :
|
|
make at91sam9x5ek_dataflash_config - use data flash
|
|
make at91sam9x5ek_mmc_config - use sd/mmc card
|
|
make at91sam9x5ek_nandflash_config - use nand flash
|
|
make at91sam9x5ek_spiflash_config - use serial flash
|
|
|
|
|
|
------------------------------------------------------------------------------
|
|
SAMA5D3XEK
|
|
------------------------------------------------------------------------------
|
|
|
|
Memory map
|
|
0x20000000 - 3FFFFFFF SDRAM (512 MB)
|
|
|
|
Environment variables
|
|
|
|
U-Boot environment variables can be stored at different places:
|
|
- Nand flash.
|
|
- SD/MMC card
|
|
- Serialflash on SPI chip select 0
|
|
|
|
You can choose your storage location at config step (here for sama5d3xek) :
|
|
make sama5d3xek_mmc_config - use SD/MMC card
|
|
make sama5d3xek_nandflash_config - use nand flash
|
|
make sama5d3xek_serialflash_config - use serial flash
|
|
|
|
|
|
II. NAND partition table
|
|
|
|
All the board support boot from NAND flash will use the following NAND
|
|
partition table
|
|
|
|
0x00000000 - 0x0003FFFF bootstrap (256 KiB)
|
|
0x00040000 - 0x000BFFFF u-boot (512 KiB)
|
|
0x000C0000 - 0x000FFFFF env (256 KiB)
|
|
0x00100000 - 0x0013FFFF env_redundant (256 KiB)
|
|
0x00140000 - 0x0017FFFF spare (256 KiB)
|
|
0x00180000 - 0x001FFFFF dtb (512 KiB)
|
|
0x00200000 - 0x007FFFFF kernel (6 MiB)
|
|
0x00800000 - 0xxxxxxxxx rootfs (All left)
|
|
|
|
III. Watchdog support
|
|
|
|
For security reasons, the at91 watchdog is running at boot time and,
|
|
if deactivated, cannot be used anymore.
|
|
If you want to use the watchdog, you will need to keep it running in
|
|
your code (make sure not to disable it in AT91Bootstrap for instance).
|
|
|
|
In the U-Boot configuration, the AT91 watchdog support is enabled using
|
|
the CONFIG_AT91SAM9_WATCHDOG and CONFIG_HW_WATCHDOG options.
|