e6676a34c4
This converts the following to Kconfig: CONFIG_MXC_UART Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Peng Fan <peng.fan@nxp.com>
73 lines
1.8 KiB
Plaintext
73 lines
1.8 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_ARCH_MX6=y
|
|
CONFIG_SYS_TEXT_BASE=0x17800000
|
|
CONFIG_SPL_GPIO_SUPPORT=y
|
|
CONFIG_SPL_LIBCOMMON_SUPPORT=y
|
|
CONFIG_SPL_LIBGENERIC_SUPPORT=y
|
|
CONFIG_ENV_SIZE=0x4000
|
|
CONFIG_ENV_OFFSET=0x100000
|
|
CONFIG_ENV_SECT_SIZE=0x10000
|
|
CONFIG_SYS_SPI_U_BOOT_OFFS=0x10000
|
|
CONFIG_TARGET_PFLA02=y
|
|
CONFIG_SPL_TEXT_BASE=0x00908000
|
|
CONFIG_SPL_MMC_SUPPORT=y
|
|
CONFIG_SPL_SERIAL_SUPPORT=y
|
|
CONFIG_NR_DRAM_BANKS=1
|
|
CONFIG_SPL=y
|
|
CONFIG_ENV_OFFSET_REDUND=0x110000
|
|
CONFIG_SPL_LIBDISK_SUPPORT=y
|
|
CONFIG_SPL_SPI_FLASH_SUPPORT=y
|
|
CONFIG_SPL_SPI_SUPPORT=y
|
|
CONFIG_CMD_HDMIDETECT=y
|
|
CONFIG_DISTRO_DEFAULTS=y
|
|
CONFIG_FIT=y
|
|
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
|
|
CONFIG_BOOTDELAY=3
|
|
# CONFIG_USE_BOOTCOMMAND is not set
|
|
CONFIG_DISPLAY_BOARDINFO_LATE=y
|
|
CONFIG_BOUNCE_BUFFER=y
|
|
CONFIG_BOARD_EARLY_INIT_F=y
|
|
CONFIG_SPL_DMA=y
|
|
CONFIG_SPL_FS_EXT4=y
|
|
CONFIG_SPL_I2C_SUPPORT=y
|
|
CONFIG_SPL_SPI_LOAD=y
|
|
CONFIG_SPL_WATCHDOG_SUPPORT=y
|
|
CONFIG_SPL_YMODEM_SUPPORT=y
|
|
# CONFIG_CMD_FLASH is not set
|
|
CONFIG_CMD_GPIO=y
|
|
CONFIG_CMD_I2C=y
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_NAND_TRIMFFS=y
|
|
CONFIG_CMD_SF=y
|
|
CONFIG_CMD_CACHE=y
|
|
CONFIG_CMD_EXT4_WRITE=y
|
|
CONFIG_CMD_MTDPARTS=y
|
|
CONFIG_MTDIDS_DEFAULT="nand0=gpmi-nand"
|
|
CONFIG_MTDPARTS_DEFAULT="mtdparts=gpmi-nand:-(nand);spi2.0:1024k(bootloader),64k(env1),64k(env2),-(rescue)"
|
|
CONFIG_CMD_UBI=y
|
|
# CONFIG_SPL_PARTITION_UUIDS is not set
|
|
CONFIG_ENV_IS_IN_SPI_FLASH=y
|
|
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_DM=y
|
|
CONFIG_FSL_USDHC=y
|
|
CONFIG_MTD=y
|
|
CONFIG_DM_MTD=y
|
|
CONFIG_MTD_RAW_NAND=y
|
|
CONFIG_NAND_MXS=y
|
|
CONFIG_SPI_FLASH=y
|
|
CONFIG_SF_DEFAULT_BUS=2
|
|
CONFIG_SF_DEFAULT_MODE=0
|
|
CONFIG_SF_DEFAULT_SPEED=20000000
|
|
CONFIG_SPI_FLASH_STMICRO=y
|
|
CONFIG_PHYLIB=y
|
|
CONFIG_PHY_MICREL=y
|
|
CONFIG_PHY_MICREL_KSZ90X1=y
|
|
CONFIG_FEC_MXC=y
|
|
CONFIG_MII=y
|
|
CONFIG_MXC_UART=y
|
|
CONFIG_SPI=y
|
|
CONFIG_MXC_SPI=y
|
|
CONFIG_DM_THERMAL=y
|
|
CONFIG_OF_LIBFDT=y
|