f76750d111
This converts the following to Kconfig: CONFIG_CONS_INDEX CONFIG_DEBUG_UART_CLOCK CONFIG_FSL_TZPC_BP147 CONFIG_GENERIC_ATMEL_MCI CONFIG_IDENT_STRING CONFIG_LIBATA CONFIG_LNX_KRNL_IMG_TEXT_OFFSET_BASE CONFIG_LPC32XX_GPIO CONFIG_MP CONFIG_MPC8XXX_GPIO CONFIG_MTD_PARTITIONS CONFIG_MVGBE CONFIG_MXC_GPIO CONFIG_NR_DRAM_BANKS CONFIG_OF_BOARD_SETUP CONFIG_OF_STDOUT_VIA_ALIAS CONFIG_OF_SYSTEM_SETUP CONFIG_PREBOOT CONFIG_ROCKCHIP_SERIAL CONFIG_RTC_ENABLE_32KHZ_OUTPUT CONFIG_RTC_MV CONFIG_SCSI_AHCI CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_SPEED CONFIG_SOFT_SPI CONFIG_SPI_FLASH_EON CONFIG_SPI_FLASH_MACRONIX CONFIG_SPI_FLASH_MTD CONFIG_SPI_FLASH_SPANSION CONFIG_SPI_FLASH_SST CONFIG_SPI_FLASH_STMICRO CONFIG_SUPPORT_RAW_INITRD CONFIG_SYS_ARCH_TIMER CONFIG_SYS_BOARD CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE CONFIG_SYS_DCACHE_OFF CONFIG_SYS_FDT_SAVE_ADDRESS CONFIG_SYS_FLASH_CFI CONFIG_SYS_FSL_ERRATUM_ESDHC135 CONFIG_SYS_HAS_SERDES CONFIG_SYS_L2CACHE_OFF CONFIG_SYS_LITTLE_ENDIAN CONFIG_SYS_LOAD_ADDR CONFIG_SYS_MMCSD_FS_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR CONFIG_SYS_NS16550 CONFIG_SYS_PLLFIN CONFIG_SYS_SPI_U_BOOT_OFFS CONFIG_TIMER_SYS_TICK_CH CONFIG_USB_EHCI_FSL CONFIG_U_QE CONFIG_VERSION_VARIABLE Signed-off-by: Tom Rini <trini@konsulko.com>
55 lines
1.5 KiB
Plaintext
55 lines
1.5 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_SKIP_LOWLEVEL_INIT=y
|
|
CONFIG_ARCH_CPU_INIT=y
|
|
CONFIG_ARCH_AT91=y
|
|
CONFIG_SYS_TEXT_BASE=0x20f00000
|
|
CONFIG_TARGET_VINCO=y
|
|
CONFIG_NR_DRAM_BANKS=1
|
|
CONFIG_ENV_SIZE=0x10000
|
|
CONFIG_ENV_OFFSET=0x10000
|
|
CONFIG_ENV_SECT_SIZE=0x1000
|
|
CONFIG_DEFAULT_DEVICE_TREE="at91-vinco"
|
|
CONFIG_ENV_VARS_UBOOT_CONFIG=y
|
|
CONFIG_SYS_LOAD_ADDR=0x22000000
|
|
CONFIG_SPI_BOOT=y
|
|
CONFIG_BOOTDELAY=3
|
|
CONFIG_USE_BOOTARGS=y
|
|
CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk rw root=/dev/mmcblk0p2 rootfstype=ext4 rootwait quiet lpj=1990656"
|
|
CONFIG_USE_BOOTCOMMAND=y
|
|
CONFIG_BOOTCOMMAND="mmc dev 0 0;mmc read ${loadaddr} ${k_offset} ${k_blksize};mmc read ${oftaddr} ${dtb_offset} ${dtb_blksize};bootz ${loadaddr} - ${oftaddr}"
|
|
# CONFIG_DISPLAY_BOARDINFO is not set
|
|
CONFIG_BOARD_EARLY_INIT_F=y
|
|
CONFIG_HUSH_PARSER=y
|
|
CONFIG_SYS_PROMPT="vinco => "
|
|
CONFIG_CMD_BOOTZ=y
|
|
# CONFIG_CMD_IMI is not set
|
|
CONFIG_CMD_GPT=y
|
|
# CONFIG_CMD_LOADS is not set
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_USB=y
|
|
CONFIG_CMD_DHCP=y
|
|
CONFIG_CMD_MII=y
|
|
CONFIG_CMD_PING=y
|
|
CONFIG_CMD_FAT=y
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_ENV_IS_IN_SPI_FLASH=y
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_AT91_GPIO=y
|
|
CONFIG_SUPPORT_EMMC_BOOT=y
|
|
CONFIG_GENERIC_ATMEL_MCI=y
|
|
CONFIG_DM_SPI_FLASH=y
|
|
CONFIG_SF_DEFAULT_SPEED=50000000
|
|
CONFIG_SPI_FLASH_STMICRO=y
|
|
CONFIG_PHY_SMSC=y
|
|
CONFIG_ETH_DESIGNWARE=y
|
|
CONFIG_MACB=y
|
|
CONFIG_ATMEL_USART=y
|
|
CONFIG_USB=y
|
|
CONFIG_USB_EHCI_HCD=y
|
|
CONFIG_USB_HOST_ETHER=y
|
|
CONFIG_USB_ETHER_SMSC95XX=y
|
|
CONFIG_USB_GADGET=y
|
|
CONFIG_USB_GADGET_MANUFACTURER="L+G VInCo"
|
|
CONFIG_USB_GADGET_ATMEL_USBA=y
|
|
CONFIG_USB_ETHER=y
|