f76750d111
This converts the following to Kconfig: CONFIG_CONS_INDEX CONFIG_DEBUG_UART_CLOCK CONFIG_FSL_TZPC_BP147 CONFIG_GENERIC_ATMEL_MCI CONFIG_IDENT_STRING CONFIG_LIBATA CONFIG_LNX_KRNL_IMG_TEXT_OFFSET_BASE CONFIG_LPC32XX_GPIO CONFIG_MP CONFIG_MPC8XXX_GPIO CONFIG_MTD_PARTITIONS CONFIG_MVGBE CONFIG_MXC_GPIO CONFIG_NR_DRAM_BANKS CONFIG_OF_BOARD_SETUP CONFIG_OF_STDOUT_VIA_ALIAS CONFIG_OF_SYSTEM_SETUP CONFIG_PREBOOT CONFIG_ROCKCHIP_SERIAL CONFIG_RTC_ENABLE_32KHZ_OUTPUT CONFIG_RTC_MV CONFIG_SCSI_AHCI CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_SPEED CONFIG_SOFT_SPI CONFIG_SPI_FLASH_EON CONFIG_SPI_FLASH_MACRONIX CONFIG_SPI_FLASH_MTD CONFIG_SPI_FLASH_SPANSION CONFIG_SPI_FLASH_SST CONFIG_SPI_FLASH_STMICRO CONFIG_SUPPORT_RAW_INITRD CONFIG_SYS_ARCH_TIMER CONFIG_SYS_BOARD CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE CONFIG_SYS_DCACHE_OFF CONFIG_SYS_FDT_SAVE_ADDRESS CONFIG_SYS_FLASH_CFI CONFIG_SYS_FSL_ERRATUM_ESDHC135 CONFIG_SYS_HAS_SERDES CONFIG_SYS_L2CACHE_OFF CONFIG_SYS_LITTLE_ENDIAN CONFIG_SYS_LOAD_ADDR CONFIG_SYS_MMCSD_FS_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR CONFIG_SYS_NS16550 CONFIG_SYS_PLLFIN CONFIG_SYS_SPI_U_BOOT_OFFS CONFIG_TIMER_SYS_TICK_CH CONFIG_USB_EHCI_FSL CONFIG_U_QE CONFIG_VERSION_VARIABLE Signed-off-by: Tom Rini <trini@konsulko.com>
92 lines
2.3 KiB
Plaintext
92 lines
2.3 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_SPL_SKIP_LOWLEVEL_INIT_ONLY=y
|
|
CONFIG_TPL_SKIP_LOWLEVEL_INIT_ONLY=y
|
|
CONFIG_SYS_ARCH_TIMER=y
|
|
CONFIG_ARCH_ROCKCHIP=y
|
|
CONFIG_SYS_TEXT_BASE=0x01000000
|
|
CONFIG_NR_DRAM_BANKS=2
|
|
CONFIG_ENV_OFFSET=0x3F8000
|
|
CONFIG_DEFAULT_DEVICE_TREE="rk3288-evb"
|
|
CONFIG_ROCKCHIP_RK3288=y
|
|
CONFIG_TARGET_EVB_RK3288=y
|
|
CONFIG_SPL_STACK_R_ADDR=0x04000000
|
|
CONFIG_SPL_SIZE_LIMIT=0x4b000
|
|
CONFIG_DEBUG_UART_BASE=0xff690000
|
|
CONFIG_DEBUG_UART_CLOCK=24000000
|
|
CONFIG_DEBUG_UART=y
|
|
CONFIG_SYS_LOAD_ADDR=0x800800
|
|
# CONFIG_ANDROID_BOOT_IMAGE is not set
|
|
CONFIG_FIT=y
|
|
CONFIG_FIT_VERBOSE=y
|
|
CONFIG_SPL_LOAD_FIT=y
|
|
# CONFIG_USE_SPL_FIT_GENERATOR is not set
|
|
CONFIG_USE_PREBOOT=y
|
|
CONFIG_DEFAULT_FDT_FILE="rk3288-evb-rk808.dtb"
|
|
CONFIG_SILENT_CONSOLE=y
|
|
CONFIG_DISPLAY_BOARDINFO_LATE=y
|
|
CONFIG_SPL_STACK_R=y
|
|
CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x10000
|
|
CONFIG_SPL_OPTEE_IMAGE=y
|
|
CONFIG_CMD_GPIO=y
|
|
CONFIG_CMD_GPT=y
|
|
CONFIG_CMD_I2C=y
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_SPI=y
|
|
CONFIG_CMD_USB=y
|
|
CONFIG_CMD_USB_MASS_STORAGE=y
|
|
# CONFIG_CMD_SETEXPR is not set
|
|
CONFIG_CMD_CACHE=y
|
|
CONFIG_CMD_TIME=y
|
|
CONFIG_CMD_PMIC=y
|
|
CONFIG_CMD_REGULATOR=y
|
|
# CONFIG_SPL_DOS_PARTITION is not set
|
|
# CONFIG_SPL_EFI_PARTITION is not set
|
|
CONFIG_SPL_PARTITION_UUIDS=y
|
|
CONFIG_SPL_OF_CONTROL=y
|
|
CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
|
|
CONFIG_ENV_IS_IN_MMC=y
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_NET_RANDOM_ETHADDR=y
|
|
CONFIG_REGMAP=y
|
|
CONFIG_SPL_REGMAP=y
|
|
CONFIG_SYSCON=y
|
|
CONFIG_SPL_SYSCON=y
|
|
CONFIG_CLK=y
|
|
CONFIG_SPL_CLK=y
|
|
CONFIG_FASTBOOT_CMD_OEM_FORMAT=y
|
|
CONFIG_ROCKCHIP_GPIO=y
|
|
CONFIG_SYS_I2C_ROCKCHIP=y
|
|
CONFIG_LED=y
|
|
CONFIG_LED_GPIO=y
|
|
CONFIG_MMC_DW=y
|
|
CONFIG_MMC_DW_ROCKCHIP=y
|
|
CONFIG_MTD=y
|
|
CONFIG_SF_DEFAULT_SPEED=20000000
|
|
CONFIG_DM_ETH=y
|
|
CONFIG_ETH_DESIGNWARE=y
|
|
CONFIG_GMAC_ROCKCHIP=y
|
|
CONFIG_PINCTRL=y
|
|
CONFIG_SPL_PINCTRL=y
|
|
CONFIG_DM_PMIC=y
|
|
CONFIG_PMIC_ACT8846=y
|
|
CONFIG_REGULATOR_ACT8846=y
|
|
CONFIG_DM_REGULATOR_FIXED=y
|
|
CONFIG_PWM_ROCKCHIP=y
|
|
CONFIG_RAM=y
|
|
CONFIG_SPL_RAM=y
|
|
CONFIG_DEBUG_UART_SHIFT=2
|
|
CONFIG_SYSRESET=y
|
|
CONFIG_USB=y
|
|
CONFIG_USB_DWC2=y
|
|
CONFIG_ROCKCHIP_USB2_PHY=y
|
|
CONFIG_USB_GADGET=y
|
|
CONFIG_USB_GADGET_DWC2_OTG=y
|
|
CONFIG_DM_VIDEO=y
|
|
# CONFIG_VIDEO_BPP8 is not set
|
|
CONFIG_DISPLAY=y
|
|
CONFIG_VIDEO_ROCKCHIP=y
|
|
CONFIG_VIDEO_ROCKCHIP_MAX_YRES=1200
|
|
CONFIG_DISPLAY_ROCKCHIP_MIPI=y
|
|
CONFIG_CMD_DHRYSTONE=y
|
|
CONFIG_ERRNO_STR=y
|