623de3f086
This converts the following to Kconfig: CONFIG_SUPPORT_EMMC_BOOT As requested by Michal Simek <michal.simek@xilinx.com>, these boards have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated: xilinx_zynqmp_zc1275_revB xilinx_zynqmp_zc1751_xm018_dc4 xilinx_zynqmp_zc1751_xm019_dc5 xilinx_zynqmp_zcu100_revC xilinx_zynqmp_zcu102_rev1_0 xilinx_zynqmp_zcu102_revA xilinx_zynqmp_zcu102_revB xilinx_zynqmp_zcu104_revA xilinx_zynqmp_zcu104_revC xilinx_zynqmp_zcu106_revA xilinx_zynqmp_zcu111_revA Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Acked-by: Lukasz Majewski <lukma@denx.de> Acked-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Ramon Fried <ramon.fried@gmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
59 lines
1.5 KiB
Plaintext
59 lines
1.5 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_ARCH_UNIPHIER=y
|
|
CONFIG_SYS_TEXT_BASE=0x84000000
|
|
CONFIG_SYS_MALLOC_F_LEN=0x2000
|
|
CONFIG_SPL_MMC_SUPPORT=y
|
|
CONFIG_SPL_SERIAL_SUPPORT=y
|
|
CONFIG_NR_DRAM_BANKS=3
|
|
CONFIG_SPL=y
|
|
CONFIG_ARCH_UNIPHIER_LD4_SLD8=y
|
|
CONFIG_MICRO_SUPPORT_CARD=y
|
|
# CONFIG_ARCH_FIXUP_FDT_MEMORY is not set
|
|
CONFIG_BOOTCOMMAND="run ${bootdev}script; run ${bootdev}boot"
|
|
CONFIG_USE_PREBOOT=y
|
|
CONFIG_PREBOOT="env exist ${bootdev}preboot && run ${bootdev}preboot"
|
|
CONFIG_LOGLEVEL=6
|
|
CONFIG_SPL_TEXT_BASE=0x00040000
|
|
CONFIG_SPL_NAND_SUPPORT=y
|
|
CONFIG_SPL_NOR_SUPPORT=y
|
|
CONFIG_CMD_CONFIG=y
|
|
CONFIG_CMD_IMLS=y
|
|
# CONFIG_CMD_XIMG is not set
|
|
CONFIG_CMD_GPIO=y
|
|
CONFIG_CMD_GPT=y
|
|
CONFIG_CMD_I2C=y
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_USB=y
|
|
CONFIG_CMD_TFTPPUT=y
|
|
CONFIG_CMD_CACHE=y
|
|
CONFIG_CMD_TIME=y
|
|
# CONFIG_CMD_MISC is not set
|
|
CONFIG_CMD_MTDPARTS=y
|
|
CONFIG_MTDIDS_DEFAULT="nand0=uniphier-nand.0"
|
|
CONFIG_MTDPARTS_DEFAULT="mtdparts=uniphier-nand.0:1m(firmware),-(UBI)"
|
|
CONFIG_CMD_UBI=y
|
|
# CONFIG_SPL_DOS_PARTITION is not set
|
|
# CONFIG_SPL_EFI_PARTITION is not set
|
|
CONFIG_DEFAULT_DEVICE_TREE="uniphier-ld4-ref"
|
|
CONFIG_NET_RANDOM_ETHADDR=y
|
|
CONFIG_GPIO_UNIPHIER=y
|
|
CONFIG_MISC=y
|
|
CONFIG_I2C_EEPROM=y
|
|
CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=10
|
|
CONFIG_SUPPORT_EMMC_BOOT=y
|
|
CONFIG_MMC_UNIPHIER=y
|
|
CONFIG_FLASH_CFI_DRIVER=y
|
|
CONFIG_SYS_FLASH_CFI=y
|
|
CONFIG_NAND=y
|
|
CONFIG_NAND_DENALI_DT=y
|
|
CONFIG_NAND_DENALI_SPARE_AREA_SKIP_BYTES=8
|
|
CONFIG_SPL_NAND_DENALI=y
|
|
CONFIG_SMC911X=y
|
|
CONFIG_SMC911X_BASE=0x0
|
|
CONFIG_SMC911X_32_BIT=y
|
|
CONFIG_USB=y
|
|
CONFIG_USB_EHCI_HCD=y
|
|
CONFIG_USB_EHCI_GENERIC=y
|
|
CONFIG_PANIC_HANG=y
|
|
CONFIG_FDT_FIXUP_PARTITIONS=y
|