a09fea1d28
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
78 lines
1.8 KiB
Plaintext
78 lines
1.8 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_TARGET_LS1012AQDS=y
|
|
CONFIG_TFABOOT=y
|
|
CONFIG_SYS_TEXT_BASE=0x82000000
|
|
CONFIG_QSPI_AHB_INIT=y
|
|
CONFIG_ENV_SIZE=0x40000
|
|
CONFIG_ENV_OFFSET=0x500000
|
|
CONFIG_NR_DRAM_BANKS=2
|
|
CONFIG_ENV_SECT_SIZE=0x40000
|
|
CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y
|
|
CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y
|
|
CONFIG_AHCI=y
|
|
CONFIG_DISTRO_DEFAULTS=y
|
|
# CONFIG_SYS_MALLOC_F is not set
|
|
CONFIG_FIT_VERBOSE=y
|
|
CONFIG_OF_BOARD_SETUP=y
|
|
CONFIG_OF_STDOUT_VIA_ALIAS=y
|
|
CONFIG_BOOTDELAY=10
|
|
CONFIG_USE_BOOTARGS=y
|
|
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 quiet lpj=250000"
|
|
# CONFIG_USE_BOOTCOMMAND is not set
|
|
CONFIG_MISC_INIT_R=y
|
|
# CONFIG_DISPLAY_BOARDINFO is not set
|
|
CONFIG_DISPLAY_BOARDINFO_LATE=y
|
|
CONFIG_CMD_GREPENV=y
|
|
CONFIG_CMD_EEPROM=y
|
|
CONFIG_CMD_MEMTEST=y
|
|
CONFIG_CMD_GPT=y
|
|
CONFIG_CMD_I2C=y
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_PCI=y
|
|
CONFIG_CMD_SPI=y
|
|
CONFIG_DEFAULT_SPI_BUS=1
|
|
CONFIG_CMD_USB=y
|
|
# CONFIG_CMD_SETEXPR is not set
|
|
CONFIG_CMD_CACHE=y
|
|
CONFIG_CMD_DATE=y
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1012a-qds"
|
|
CONFIG_ENV_IS_IN_SPI_FLASH=y
|
|
CONFIG_USE_ENV_SPI_BUS=y
|
|
CONFIG_ENV_SPI_BUS=0
|
|
CONFIG_USE_ENV_SPI_MAX_HZ=y
|
|
CONFIG_ENV_SPI_MAX_HZ=1000000
|
|
CONFIG_USE_ENV_SPI_MODE=y
|
|
CONFIG_ENV_SPI_MODE=0x03
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_NET_RANDOM_ETHADDR=y
|
|
CONFIG_DM=y
|
|
CONFIG_SCSI_AHCI=y
|
|
CONFIG_SATA_CEVA=y
|
|
CONFIG_DM_MMC=y
|
|
CONFIG_FSL_ESDHC=y
|
|
CONFIG_DM_SPI_FLASH=y
|
|
CONFIG_SF_DEFAULT_BUS=1
|
|
CONFIG_SF_DEFAULT_MODE=0
|
|
CONFIG_SF_DEFAULT_SPEED=10000000
|
|
# CONFIG_SPI_FLASH_BAR is not set
|
|
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
|
|
CONFIG_FSL_PFE=y
|
|
CONFIG_DM_ETH=y
|
|
CONFIG_E1000=y
|
|
CONFIG_PCI=y
|
|
CONFIG_DM_PCI=y
|
|
CONFIG_DM_PCI_COMPAT=y
|
|
CONFIG_PCIE_LAYERSCAPE=y
|
|
CONFIG_SCSI=y
|
|
CONFIG_DM_SCSI=y
|
|
CONFIG_SYS_NS16550=y
|
|
CONFIG_SPI=y
|
|
CONFIG_DM_SPI=y
|
|
CONFIG_FSL_DSPI=y
|
|
CONFIG_FSL_QSPI=y
|
|
CONFIG_USB=y
|
|
CONFIG_DM_USB=y
|
|
CONFIG_USB_XHCI_HCD=y
|
|
CONFIG_USB_XHCI_DWC3=y
|