leandrof/u-boot
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
ad415c80a5
u-boot/drivers/spi/sh_qspi.c
Lukasz Majewski 56c4046038 spi: Convert CONFIG_DM_SPI* to CONFIG_$(SPL_TPL_)DM_SPI* 
This change allows more fine tuning of driver model based SPI support in
SPL and TPL. It is now possible to explicitly enable/disable the DM_SPI
support in SPL and TPL via Kconfig option.

Before this change it was necessary to use:
    /* SPI Flash Configs */
    #if defined(CONFIG_SPL_BUILD)
    #undef CONFIG_DM_SPI
    #undef CONFIG_DM_SPI_FLASH
    #undef CONFIG_SPI_FLASH_MTD
    #endif

in the ./include/configs/<board>.h, which is error prone and shall be
avoided when we strive to switch to Kconfig.

The goal of this patch:

Provide distinction for DM_SPI support in both U-Boot proper and SPL (TPL).
Valid use case is when U-Boot proper wants to use DM_SPI, but SPL must
still support non DM driver.

Another use case is the conversion of non DM/DTS SPI driver to support
DM/DTS. When such driver needs to work in both SPL and U-Boot proper, the
distinction is needed in Kconfig (also if SPL version of the driver
supports OF_PLATDATA).

In the end of the day one would have to support following use cases (in
single driver file - e.g. mxs_spi.c):

- U-Boot proper driver supporting DT/DTS
- U-Boot proper driver without DT/DTS support (deprecated)
- SPL driver without DT/DTS support
- SPL (and TPL) driver with DT/DTS (when the SoC has enough resources to
  run full blown DT/DTS)
- SPL driver with DT/DTS and SPL_OF_PLATDATA (when one have constrained
  environment with no fitImage and OF_LIBFDT support).

Some boards do require SPI support (with DM) in SPL (TPL) and some only
have DM_SPI{_FLASH} defined to allow compiling SPL.

This patch converts #ifdef CONFIG_DM_SPI* to #if CONFIG_IS_ENABLED(DM_SPI)
and provides corresponding defines in Kconfig.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[trini: Fixup a few platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-29 13:34:43 -04:00

361 lines
7.5 KiB
C
Raw Blame History

// SPDX-License-Identifier: GPL-2.0
/*
* SH QSPI (Quad SPI) driver
*
* Copyright (C) 2013 Renesas Electronics Corporation
* Copyright (C) 2013 Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
*/
#include <common.h>
#include <console.h>
#include <malloc.h>
#include <spi.h>
#include <wait_bit.h>
#include <asm/arch/rmobile.h>
#include <asm/io.h>
#include <linux/bitops.h>
/* SH QSPI register bit masks <REG>_<BIT> */
#define SPCR_MSTR 0x08
#define SPCR_SPE 0x40
#define SPSR_SPRFF 0x80
#define SPSR_SPTEF 0x20
#define SPPCR_IO3FV 0x04
#define SPPCR_IO2FV 0x02
#define SPPCR_IO1FV 0x01
#define SPBDCR_RXBC0 BIT(0)
#define SPCMD_SCKDEN BIT(15)
#define SPCMD_SLNDEN BIT(14)
#define SPCMD_SPNDEN BIT(13)
#define SPCMD_SSLKP BIT(7)
#define SPCMD_BRDV0 BIT(2)
#define SPCMD_INIT1 SPCMD_SCKDEN | SPCMD_SLNDEN | \
SPCMD_SPNDEN | SPCMD_SSLKP | \
SPCMD_BRDV0
#define SPCMD_INIT2 SPCMD_SPNDEN | SPCMD_SSLKP | \
SPCMD_BRDV0
#define SPBFCR_TXRST BIT(7)
#define SPBFCR_RXRST BIT(6)
#define SPBFCR_TXTRG 0x30
#define SPBFCR_RXTRG 0x07
/* SH QSPI register set */
struct sh_qspi_regs {
u8 spcr;
u8 sslp;
u8 sppcr;
u8 spsr;
u32 spdr;
u8 spscr;
u8 spssr;
u8 spbr;
u8 spdcr;
u8 spckd;
u8 sslnd;
u8 spnd;
u8 dummy0;
u16 spcmd0;
u16 spcmd1;
u16 spcmd2;
u16 spcmd3;
u8 spbfcr;
u8 dummy1;
u16 spbdcr;
u32 spbmul0;
u32 spbmul1;
u32 spbmul2;
u32 spbmul3;
};
struct sh_qspi_slave {
#if !CONFIG_IS_ENABLED(DM_SPI)
struct spi_slave slave;
#endif
struct sh_qspi_regs *regs;
};
static void sh_qspi_init(struct sh_qspi_slave *ss)
{
/* QSPI initialize */
/* Set master mode only */
writeb(SPCR_MSTR, &ss->regs->spcr);
/* Set SSL signal level */
writeb(0x00, &ss->regs->sslp);
/* Set MOSI signal value when transfer is in idle state */
writeb(SPPCR_IO3FV|SPPCR_IO2FV, &ss->regs->sppcr);
/* Set bit rate. See 58.3.8 Quad Serial Peripheral Interface */
writeb(0x01, &ss->regs->spbr);
/* Disable Dummy Data Transmission */
writeb(0x00, &ss->regs->spdcr);
/* Set clock delay value */
writeb(0x00, &ss->regs->spckd);
/* Set SSL negation delay value */
writeb(0x00, &ss->regs->sslnd);
/* Set next-access delay value */
writeb(0x00, &ss->regs->spnd);
/* Set equence command */
writew(SPCMD_INIT2, &ss->regs->spcmd0);
/* Reset transfer and receive Buffer */
setbits_8(&ss->regs->spbfcr, SPBFCR_TXRST|SPBFCR_RXRST);
/* Clear transfer and receive Buffer control bit */
clrbits_8(&ss->regs->spbfcr, SPBFCR_TXRST|SPBFCR_RXRST);
/* Set equence control method. Use equence0 only */
writeb(0x00, &ss->regs->spscr);
/* Enable SPI function */
setbits_8(&ss->regs->spcr, SPCR_SPE);
}
static void sh_qspi_cs_activate(struct sh_qspi_slave *ss)
{
/* Set master mode only */
writeb(SPCR_MSTR, &ss->regs->spcr);
/* Set command */
writew(SPCMD_INIT1, &ss->regs->spcmd0);
/* Reset transfer and receive Buffer */
setbits_8(&ss->regs->spbfcr, SPBFCR_TXRST|SPBFCR_RXRST);
/* Clear transfer and receive Buffer control bit */
clrbits_8(&ss->regs->spbfcr, SPBFCR_TXRST|SPBFCR_RXRST);
/* Set equence control method. Use equence0 only */
writeb(0x00, &ss->regs->spscr);
/* Enable SPI function */
setbits_8(&ss->regs->spcr, SPCR_SPE);
}
static void sh_qspi_cs_deactivate(struct sh_qspi_slave *ss)
{
/* Disable SPI Function */
clrbits_8(&ss->regs->spcr, SPCR_SPE);
}
static int sh_qspi_xfer_common(struct sh_qspi_slave *ss, unsigned int bitlen,
const void *dout, void *din, unsigned long flags)
{
u32 nbyte, chunk;
int i, ret = 0;
u8 dtdata = 0, drdata;
u8 *tdata = &dtdata, *rdata = &drdata;
u32 *spbmul0 = &ss->regs->spbmul0;
if (dout == NULL && din == NULL) {
if (flags & SPI_XFER_END)
sh_qspi_cs_deactivate(ss);
return 0;
}
if (bitlen % 8) {
printf("%s: bitlen is not 8bit alined %d", __func__, bitlen);
return 1;
}
nbyte = bitlen / 8;
if (flags & SPI_XFER_BEGIN) {
sh_qspi_cs_activate(ss);
/* Set 1048576 byte */
writel(0x100000, spbmul0);
}
if (flags & SPI_XFER_END)
writel(nbyte, spbmul0);
if (dout != NULL)
tdata = (u8 *)dout;
if (din != NULL)
rdata = din;
while (nbyte > 0) {
/*
* Check if there is 32 Byte chunk and if there is, transfer
* it in one burst, otherwise transfer on byte-by-byte basis.
*/
chunk = (nbyte >= 32) ? 32 : 1;
clrsetbits_8(&ss->regs->spbfcr, SPBFCR_TXTRG | SPBFCR_RXTRG,
chunk == 32 ? SPBFCR_TXTRG | SPBFCR_RXTRG : 0);
ret = wait_for_bit_8(&ss->regs->spsr, SPSR_SPTEF,
true, 1000, true);
if (ret)
return ret;
for (i = 0; i < chunk; i++) {
writeb(*tdata, &ss->regs->spdr);
if (dout != NULL)
tdata++;
}
ret = wait_for_bit_8(&ss->regs->spsr, SPSR_SPRFF,
true, 1000, true);
if (ret)
return ret;
for (i = 0; i < chunk; i++) {
*rdata = readb(&ss->regs->spdr);
if (din != NULL)
rdata++;
}
nbyte -= chunk;
}
if (flags & SPI_XFER_END)
sh_qspi_cs_deactivate(ss);
return ret;
}
#if !CONFIG_IS_ENABLED(DM_SPI)
static inline struct sh_qspi_slave *to_sh_qspi(struct spi_slave *slave)
{
return container_of(slave, struct sh_qspi_slave, slave);
}
int spi_cs_is_valid(unsigned int bus, unsigned int cs)
{
return 1;
}
void spi_cs_activate(struct spi_slave *slave)
{
struct sh_qspi_slave *ss = to_sh_qspi(slave);
sh_qspi_cs_activate(ss);
}
void spi_cs_deactivate(struct spi_slave *slave)
{
struct sh_qspi_slave *ss = to_sh_qspi(slave);
sh_qspi_cs_deactivate(ss);
}
struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
unsigned int max_hz, unsigned int mode)
{
struct sh_qspi_slave *ss;
if (!spi_cs_is_valid(bus, cs))
return NULL;
ss = spi_alloc_slave(struct sh_qspi_slave, bus, cs);
if (!ss) {
printf("SPI_error: Fail to allocate sh_qspi_slave\n");
return NULL;
}
ss->regs = (struct sh_qspi_regs *)SH_QSPI_BASE;
/* Init SH QSPI */
sh_qspi_init(ss);
return &ss->slave;
}
void spi_free_slave(struct spi_slave *slave)
{
struct sh_qspi_slave *spi = to_sh_qspi(slave);
free(spi);
}
int spi_claim_bus(struct spi_slave *slave)
{
return 0;
}
void spi_release_bus(struct spi_slave *slave)
{
}
int spi_xfer(struct spi_slave *slave, unsigned int bitlen,
const void *dout, void *din, unsigned long flags)
{
struct sh_qspi_slave *ss = to_sh_qspi(slave);
return sh_qspi_xfer_common(ss, bitlen, dout, din, flags);
}
#else
#include <dm.h>
static int sh_qspi_xfer(struct udevice *dev, unsigned int bitlen,
const void *dout, void *din, unsigned long flags)
{
struct udevice *bus = dev->parent;
struct sh_qspi_slave *ss = dev_get_platdata(bus);
return sh_qspi_xfer_common(ss, bitlen, dout, din, flags);
}
static int sh_qspi_set_speed(struct udevice *dev, uint speed)
{
/* This is a SPI NOR controller, do nothing. */
return 0;
}
static int sh_qspi_set_mode(struct udevice *dev, uint mode)
{
/* This is a SPI NOR controller, do nothing. */
return 0;
}
static int sh_qspi_probe(struct udevice *dev)
{
struct sh_qspi_slave *ss = dev_get_platdata(dev);
sh_qspi_init(ss);
return 0;
}
static int sh_qspi_ofdata_to_platdata(struct udevice *dev)
{
struct sh_qspi_slave *plat = dev_get_platdata(dev);
plat->regs = (struct sh_qspi_regs *)dev_read_addr(dev);
return 0;
}
static const struct dm_spi_ops sh_qspi_ops = {
.xfer = sh_qspi_xfer,
.set_speed = sh_qspi_set_speed,
.set_mode = sh_qspi_set_mode,
};
static const struct udevice_id sh_qspi_ids[] = {
{ .compatible = "renesas,qspi" },
{ }
};
U_BOOT_DRIVER(sh_qspi) = {
.name = "sh_qspi",
.id = UCLASS_SPI,
.of_match = sh_qspi_ids,
.ops = &sh_qspi_ops,
.ofdata_to_platdata = sh_qspi_ofdata_to_platdata,
.platdata_auto_alloc_size = sizeof(struct sh_qspi_slave),
.probe = sh_qspi_probe,
};
#endif
Reference in New Issue View Git Blame Copy Permalink