a09fea1d28
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
66 lines
1.6 KiB
C
66 lines
1.6 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* (C) Copyright 2008-2010
|
|
* Gražvydas Ignotas <notasas@gmail.com>
|
|
*
|
|
* Configuration settings for the OMAP3 Pandora.
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/* override base for compatibility with MLO the device ships with */
|
|
|
|
#include <configs/ti_omap3_common.h>
|
|
|
|
#define CONFIG_REVISION_TAG 1
|
|
|
|
#define CONFIG_SYS_DEVICE_NULLDEV 1
|
|
|
|
/*
|
|
* Board NAND Info.
|
|
*/
|
|
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_SW
|
|
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
|
|
#define CONFIG_SYS_NAND_OOBSIZE 64
|
|
|
|
|
|
#define CONFIG_BOOTCOMMAND \
|
|
"run distro_bootcmd; " \
|
|
"setenv bootargs ${bootargs_ubi}; " \
|
|
"if mmc rescan && load mmc 0:1 ${loadaddr} autoboot.scr; then " \
|
|
"source ${loadaddr}; " \
|
|
"fi; " \
|
|
"ubi part boot && ubifsmount ubi:boot && " \
|
|
"ubifsload ${loadaddr} uImage && bootm ${loadaddr}"
|
|
|
|
#define BOOT_TARGET_DEVICES(func) \
|
|
func(MMC, mmc, 0) \
|
|
|
|
#include <config_distro_bootcmd.h>
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
DEFAULT_LINUX_BOOT_ENV \
|
|
"usbtty=cdc_acm\0" \
|
|
"bootargs_ubi=ubi.mtd=4 ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs " \
|
|
"rw rootflags=bulk_read vram=6272K omapfb.vram=0:3000K\0" \
|
|
"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
|
|
BOOTENV \
|
|
|
|
/* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
|
|
#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
|
|
0x01F00000) /* 31MB */
|
|
|
|
#if defined(CONFIG_NAND)
|
|
#define CONFIG_SYS_FLASH_BASE NAND_BASE
|
|
#endif
|
|
|
|
/* Monitor at start of flash */
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
|
|
|
|
|
|
#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
|
|
|
|
#endif /* __CONFIG_H */
|