3788b451e3
Cc: Tom Rini <trini@konsulko.com> Signed-off-by: Jagan Teki <jagan@openedev.com>
494 lines
15 KiB
C
494 lines
15 KiB
C
/*
|
|
* Copyright 2016 Freescale Semiconductor, Inc.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#ifndef __LS1046AQDS_H__
|
|
#define __LS1046AQDS_H__
|
|
|
|
#include "ls1046a_common.h"
|
|
|
|
#if defined(CONFIG_NAND_BOOT) || defined(CONFIG_SD_BOOT)
|
|
#define CONFIG_SYS_TEXT_BASE 0x82000000
|
|
#elif defined(CONFIG_QSPI_BOOT)
|
|
#define CONFIG_SYS_TEXT_BASE 0x40010000
|
|
#else
|
|
#define CONFIG_SYS_TEXT_BASE 0x60100000
|
|
#endif
|
|
|
|
#ifndef __ASSEMBLY__
|
|
unsigned long get_board_sys_clk(void);
|
|
unsigned long get_board_ddr_clk(void);
|
|
#endif
|
|
|
|
#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
|
|
#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk()
|
|
|
|
#define CONFIG_SKIP_LOWLEVEL_INIT
|
|
|
|
#define CONFIG_LAYERSCAPE_NS_ACCESS
|
|
|
|
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
|
|
/* Physical Memory Map */
|
|
#define CONFIG_CHIP_SELECTS_PER_CTRL 4
|
|
#define CONFIG_NR_DRAM_BANKS 2
|
|
|
|
#define CONFIG_DDR_SPD
|
|
#define SPD_EEPROM_ADDRESS 0x51
|
|
#define CONFIG_SYS_SPD_BUS_NUM 0
|
|
|
|
#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
|
|
|
|
#define CONFIG_DDR_ECC
|
|
#ifdef CONFIG_DDR_ECC
|
|
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
|
|
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
|
|
#endif
|
|
|
|
/* DSPI */
|
|
#ifdef CONFIG_FSL_DSPI
|
|
#define CONFIG_SPI_FLASH_STMICRO /* cs0 */
|
|
#define CONFIG_SPI_FLASH_SST /* cs1 */
|
|
#define CONFIG_SPI_FLASH_EON /* cs2 */
|
|
#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
|
|
#define CONFIG_SF_DEFAULT_BUS 1
|
|
#define CONFIG_SF_DEFAULT_CS 0
|
|
#endif
|
|
#endif
|
|
|
|
/* QSPI */
|
|
#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
|
|
#ifdef CONFIG_FSL_QSPI
|
|
#define CONFIG_SPI_FLASH_SPANSION
|
|
#define FSL_QSPI_FLASH_SIZE (1 << 24)
|
|
#define FSL_QSPI_FLASH_NUM 2
|
|
#endif
|
|
#endif
|
|
|
|
#ifdef CONFIG_SYS_DPAA_FMAN
|
|
#define CONFIG_FMAN_ENET
|
|
#define CONFIG_PHYLIB
|
|
#define CONFIG_PHY_VITESSE
|
|
#define CONFIG_PHY_REALTEK
|
|
#define CONFIG_PHYLIB_10G
|
|
#define RGMII_PHY1_ADDR 0x1
|
|
#define RGMII_PHY2_ADDR 0x2
|
|
#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
|
|
#define SGMII_CARD_PORT2_PHY_ADDR 0x1D
|
|
#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
|
|
#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
|
|
/* PHY address on QSGMII riser card on slot 2 */
|
|
#define QSGMII_CARD_PORT1_PHY_ADDR_S2 0x8
|
|
#define QSGMII_CARD_PORT2_PHY_ADDR_S2 0x9
|
|
#define QSGMII_CARD_PORT3_PHY_ADDR_S2 0xA
|
|
#define QSGMII_CARD_PORT4_PHY_ADDR_S2 0xB
|
|
#endif
|
|
|
|
#ifdef CONFIG_RAMBOOT_PBL
|
|
#define CONFIG_SYS_FSL_PBL_PBI \
|
|
board/freescale/ls1046aqds/ls1046aqds_pbi.cfg
|
|
#endif
|
|
|
|
#ifdef CONFIG_NAND_BOOT
|
|
#define CONFIG_SYS_FSL_PBL_RCW \
|
|
board/freescale/ls1046aqds/ls1046aqds_rcw_nand.cfg
|
|
#endif
|
|
|
|
#ifdef CONFIG_SD_BOOT
|
|
#ifdef CONFIG_SD_BOOT_QSPI
|
|
#define CONFIG_SYS_FSL_PBL_RCW \
|
|
board/freescale/ls1046aqds/ls1046aqds_rcw_sd_qspi.cfg
|
|
#else
|
|
#define CONFIG_SYS_FSL_PBL_RCW \
|
|
board/freescale/ls1046aqds/ls1046aqds_rcw_sd_ifc.cfg
|
|
#endif
|
|
#endif
|
|
|
|
/* IFC */
|
|
#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
|
|
#define CONFIG_FSL_IFC
|
|
/*
|
|
* CONFIG_SYS_FLASH_BASE has the final address (core view)
|
|
* CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
|
|
* CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
|
|
* CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting
|
|
*/
|
|
#define CONFIG_SYS_FLASH_BASE 0x60000000
|
|
#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
|
|
#define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000
|
|
|
|
#ifndef CONFIG_SYS_NO_FLASH
|
|
#define CONFIG_FLASH_CFI_DRIVER
|
|
#define CONFIG_SYS_FLASH_CFI
|
|
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
|
|
#define CONFIG_SYS_FLASH_QUIET_TEST
|
|
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
|
|
#endif
|
|
#endif
|
|
|
|
/* LPUART */
|
|
#ifdef CONFIG_LPUART
|
|
#define CONFIG_LPUART_32B_REG
|
|
#define CFG_UART_MUX_MASK 0x6
|
|
#define CFG_UART_MUX_SHIFT 1
|
|
#define CFG_LPUART_EN 0x2
|
|
#endif
|
|
|
|
/* SATA */
|
|
#define CONFIG_LIBATA
|
|
#define CONFIG_SCSI_AHCI
|
|
#define CONFIG_SCSI_AHCI_PLAT
|
|
#define CONFIG_SCSI
|
|
#define CONFIG_DOS_PARTITION
|
|
|
|
#define CONFIG_PARTITION_UUIDS
|
|
#define CONFIG_EFI_PARTITION
|
|
#define CONFIG_CMD_GPT
|
|
|
|
/* EEPROM */
|
|
#define CONFIG_ID_EEPROM
|
|
#define CONFIG_SYS_I2C_EEPROM_NXID
|
|
#define CONFIG_SYS_EEPROM_BUS_NUM 0
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
|
|
|
|
#define CONFIG_SYS_SATA AHCI_BASE_ADDR
|
|
|
|
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
|
|
#define CONFIG_SYS_SCSI_MAX_LUN 1
|
|
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
|
|
CONFIG_SYS_SCSI_MAX_LUN)
|
|
|
|
/*
|
|
* IFC Definitions
|
|
*/
|
|
#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
|
|
#define CONFIG_SYS_NOR0_CSPR_EXT (0x0)
|
|
#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
|
|
CSPR_PORT_SIZE_16 | \
|
|
CSPR_MSEL_NOR | \
|
|
CSPR_V)
|
|
#define CONFIG_SYS_NOR1_CSPR_EXT (0x0)
|
|
#define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
|
|
+ 0x8000000) | \
|
|
CSPR_PORT_SIZE_16 | \
|
|
CSPR_MSEL_NOR | \
|
|
CSPR_V)
|
|
#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128 * 1024 * 1024)
|
|
|
|
#define CONFIG_SYS_NOR_CSOR (CSOR_NOR_ADM_SHIFT(4) | \
|
|
CSOR_NOR_TRHZ_80)
|
|
#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
|
|
FTIM0_NOR_TEADC(0x5) | \
|
|
FTIM0_NOR_TEAHC(0x5))
|
|
#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
|
|
FTIM1_NOR_TRAD_NOR(0x1a) | \
|
|
FTIM1_NOR_TSEQRAD_NOR(0x13))
|
|
#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
|
|
FTIM2_NOR_TCH(0x4) | \
|
|
FTIM2_NOR_TWPH(0xe) | \
|
|
FTIM2_NOR_TWP(0x1c))
|
|
#define CONFIG_SYS_NOR_FTIM3 0
|
|
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
|
|
|
|
#define CONFIG_SYS_FLASH_EMPTY_INFO
|
|
#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS, \
|
|
CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000}
|
|
|
|
#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
|
|
#define CONFIG_SYS_WRITE_SWAPPED_DATA
|
|
|
|
/*
|
|
* NAND Flash Definitions
|
|
*/
|
|
#define CONFIG_NAND_FSL_IFC
|
|
|
|
#define CONFIG_SYS_NAND_BASE 0x7e800000
|
|
#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
|
|
|
|
#define CONFIG_SYS_NAND_CSPR_EXT (0x0)
|
|
|
|
#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
|
|
| CSPR_PORT_SIZE_8 \
|
|
| CSPR_MSEL_NAND \
|
|
| CSPR_V)
|
|
#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
|
|
#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
|
|
| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
|
|
| CSOR_NAND_ECC_MODE_8 /* 8-bit ECC */ \
|
|
| CSOR_NAND_RAL_3 /* RAL = 3 Bytes */ \
|
|
| CSOR_NAND_PGS_4K /* Page Size = 4K */ \
|
|
| CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \
|
|
| CSOR_NAND_PB(64)) /* 64 Pages Per Block */
|
|
|
|
#define CONFIG_SYS_NAND_ONFI_DETECTION
|
|
|
|
#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x7) | \
|
|
FTIM0_NAND_TWP(0x18) | \
|
|
FTIM0_NAND_TWCHT(0x7) | \
|
|
FTIM0_NAND_TWH(0xa))
|
|
#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
|
|
FTIM1_NAND_TWBE(0x39) | \
|
|
FTIM1_NAND_TRR(0xe) | \
|
|
FTIM1_NAND_TRP(0x18))
|
|
#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0xf) | \
|
|
FTIM2_NAND_TREH(0xa) | \
|
|
FTIM2_NAND_TWHRE(0x1e))
|
|
#define CONFIG_SYS_NAND_FTIM3 0x0
|
|
|
|
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
|
#define CONFIG_MTD_NAND_VERIFY_WRITE
|
|
#define CONFIG_CMD_NAND
|
|
|
|
#define CONFIG_SYS_NAND_BLOCK_SIZE (256 * 1024)
|
|
#endif
|
|
|
|
#ifdef CONFIG_NAND_BOOT
|
|
#define CONFIG_SPL_PAD_TO 0x40000 /* block aligned */
|
|
#define CONFIG_SYS_NAND_U_BOOT_OFFS CONFIG_SPL_PAD_TO
|
|
#define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10)
|
|
#endif
|
|
|
|
#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
|
|
#define CONFIG_QIXIS_I2C_ACCESS
|
|
#define CONFIG_SYS_I2C_EARLY_INIT
|
|
#define CONFIG_SYS_NO_FLASH
|
|
#endif
|
|
|
|
/*
|
|
* QIXIS Definitions
|
|
*/
|
|
#define CONFIG_FSL_QIXIS
|
|
|
|
#ifdef CONFIG_FSL_QIXIS
|
|
#define QIXIS_BASE 0x7fb00000
|
|
#define QIXIS_BASE_PHYS QIXIS_BASE
|
|
#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
|
|
#define QIXIS_LBMAP_SWITCH 6
|
|
#define QIXIS_LBMAP_MASK 0x0f
|
|
#define QIXIS_LBMAP_SHIFT 0
|
|
#define QIXIS_LBMAP_DFLTBANK 0x00
|
|
#define QIXIS_LBMAP_ALTBANK 0x04
|
|
#define QIXIS_LBMAP_NAND 0x09
|
|
#define QIXIS_LBMAP_SD 0x00
|
|
#define QIXIS_LBMAP_SD_QSPI 0xff
|
|
#define QIXIS_LBMAP_QSPI 0xff
|
|
#define QIXIS_RCW_SRC_NAND 0x110
|
|
#define QIXIS_RCW_SRC_SD 0x040
|
|
#define QIXIS_RCW_SRC_QSPI 0x045
|
|
#define QIXIS_RST_CTL_RESET 0x41
|
|
#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
|
|
#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
|
|
#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
|
|
|
|
#define CONFIG_SYS_FPGA_CSPR_EXT (0x0)
|
|
#define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) | \
|
|
CSPR_PORT_SIZE_8 | \
|
|
CSPR_MSEL_GPCM | \
|
|
CSPR_V)
|
|
#define CONFIG_SYS_FPGA_AMASK IFC_AMASK(64 * 1024)
|
|
#define CONFIG_SYS_FPGA_CSOR (CSOR_NOR_ADM_SHIFT(4) | \
|
|
CSOR_NOR_NOR_MODE_AVD_NOR | \
|
|
CSOR_NOR_TRHZ_80)
|
|
|
|
/*
|
|
* QIXIS Timing parameters for IFC GPCM
|
|
*/
|
|
#define CONFIG_SYS_FPGA_FTIM0 (FTIM0_GPCM_TACSE(0xc) | \
|
|
FTIM0_GPCM_TEADC(0x20) | \
|
|
FTIM0_GPCM_TEAHC(0x10))
|
|
#define CONFIG_SYS_FPGA_FTIM1 (FTIM1_GPCM_TACO(0x50) | \
|
|
FTIM1_GPCM_TRAD(0x1f))
|
|
#define CONFIG_SYS_FPGA_FTIM2 (FTIM2_GPCM_TCS(0x8) | \
|
|
FTIM2_GPCM_TCH(0x8) | \
|
|
FTIM2_GPCM_TWP(0xf0))
|
|
#define CONFIG_SYS_FPGA_FTIM3 0x0
|
|
#endif
|
|
|
|
#ifdef CONFIG_NAND_BOOT
|
|
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
|
|
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
|
|
#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
|
|
#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
|
|
#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
|
|
#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
|
|
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
|
|
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
|
|
#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT
|
|
#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR
|
|
#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
|
|
#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
|
|
#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
|
|
#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
|
|
#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
|
|
#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
|
|
#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR1_CSPR_EXT
|
|
#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR1_CSPR
|
|
#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK
|
|
#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR
|
|
#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0
|
|
#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1
|
|
#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2
|
|
#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3
|
|
#define CONFIG_SYS_CSPR3_EXT CONFIG_SYS_FPGA_CSPR_EXT
|
|
#define CONFIG_SYS_CSPR3 CONFIG_SYS_FPGA_CSPR
|
|
#define CONFIG_SYS_AMASK3 CONFIG_SYS_FPGA_AMASK
|
|
#define CONFIG_SYS_CSOR3 CONFIG_SYS_FPGA_CSOR
|
|
#define CONFIG_SYS_CS3_FTIM0 CONFIG_SYS_FPGA_FTIM0
|
|
#define CONFIG_SYS_CS3_FTIM1 CONFIG_SYS_FPGA_FTIM1
|
|
#define CONFIG_SYS_CS3_FTIM2 CONFIG_SYS_FPGA_FTIM2
|
|
#define CONFIG_SYS_CS3_FTIM3 CONFIG_SYS_FPGA_FTIM3
|
|
#else
|
|
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
|
|
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR
|
|
#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
|
|
#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
|
|
#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
|
|
#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
|
|
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
|
|
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
|
|
#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT
|
|
#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR
|
|
#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
|
|
#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
|
|
#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
|
|
#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
|
|
#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
|
|
#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
|
|
#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
|
|
#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
|
|
#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
|
|
#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR
|
|
#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0
|
|
#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
|
|
#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
|
|
#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
|
|
#define CONFIG_SYS_CSPR3_EXT CONFIG_SYS_FPGA_CSPR_EXT
|
|
#define CONFIG_SYS_CSPR3 CONFIG_SYS_FPGA_CSPR
|
|
#define CONFIG_SYS_AMASK3 CONFIG_SYS_FPGA_AMASK
|
|
#define CONFIG_SYS_CSOR3 CONFIG_SYS_FPGA_CSOR
|
|
#define CONFIG_SYS_CS3_FTIM0 CONFIG_SYS_FPGA_FTIM0
|
|
#define CONFIG_SYS_CS3_FTIM1 CONFIG_SYS_FPGA_FTIM1
|
|
#define CONFIG_SYS_CS3_FTIM2 CONFIG_SYS_FPGA_FTIM2
|
|
#define CONFIG_SYS_CS3_FTIM3 CONFIG_SYS_FPGA_FTIM3
|
|
#endif
|
|
|
|
/*
|
|
* I2C bus multiplexer
|
|
*/
|
|
#define I2C_MUX_PCA_ADDR_PRI 0x77
|
|
#define I2C_MUX_PCA_ADDR_SEC 0x76 /* Secondary multiplexer */
|
|
#define I2C_RETIMER_ADDR 0x18
|
|
#define I2C_MUX_CH_DEFAULT 0x8
|
|
#define I2C_MUX_CH_CH7301 0xC
|
|
#define I2C_MUX_CH5 0xD
|
|
#define I2C_MUX_CH6 0xE
|
|
#define I2C_MUX_CH7 0xF
|
|
|
|
#define I2C_MUX_CH_VOL_MONITOR 0xa
|
|
|
|
/* Voltage monitor on channel 2*/
|
|
#define I2C_VOL_MONITOR_ADDR 0x40
|
|
#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2
|
|
#define I2C_VOL_MONITOR_BUS_V_OVF 0x1
|
|
#define I2C_VOL_MONITOR_BUS_V_SHIFT 3
|
|
|
|
#define CONFIG_VID_FLS_ENV "ls1046aqds_vdd_mv"
|
|
#ifndef CONFIG_SPL_BUILD
|
|
#define CONFIG_VID
|
|
#endif
|
|
#define CONFIG_VOL_MONITOR_IR36021_SET
|
|
#define CONFIG_VOL_MONITOR_INA220
|
|
/* The lowest and highest voltage allowed for LS1046AQDS */
|
|
#define VDD_MV_MIN 819
|
|
#define VDD_MV_MAX 1212
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_MISC_INIT_R
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
#define CONFIG_AUTO_COMPLETE
|
|
#define CONFIG_SYS_PBSIZE \
|
|
(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x80000000
|
|
#define CONFIG_SYS_MEMTEST_END 0x9fffffff
|
|
|
|
#define CONFIG_SYS_HZ 1000
|
|
|
|
/*
|
|
* Stack sizes
|
|
* The stack sizes are set up in start.S using the settings below
|
|
*/
|
|
#define CONFIG_STACKSIZE (30 * 1024)
|
|
|
|
#define CONFIG_SYS_INIT_SP_OFFSET \
|
|
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
|
|
|
|
/*
|
|
* Environment
|
|
*/
|
|
#define CONFIG_ENV_OVERWRITE
|
|
|
|
#ifdef CONFIG_NAND_BOOT
|
|
#define CONFIG_ENV_IS_IN_NAND
|
|
#define CONFIG_ENV_SIZE 0x2000
|
|
#define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE)
|
|
#elif defined(CONFIG_SD_BOOT)
|
|
#define CONFIG_ENV_OFFSET (1024 * 1024)
|
|
#define CONFIG_ENV_IS_IN_MMC
|
|
#define CONFIG_SYS_MMC_ENV_DEV 0
|
|
#define CONFIG_ENV_SIZE 0x2000
|
|
#elif defined(CONFIG_QSPI_BOOT)
|
|
#define CONFIG_ENV_IS_IN_SPI_FLASH
|
|
#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
|
|
#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
|
|
#define CONFIG_ENV_SECT_SIZE 0x10000
|
|
#else
|
|
#define CONFIG_ENV_IS_IN_FLASH
|
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x200000)
|
|
#define CONFIG_ENV_SECT_SIZE 0x20000
|
|
#define CONFIG_ENV_SIZE 0x20000
|
|
#endif
|
|
|
|
#define CONFIG_CMDLINE_TAG
|
|
|
|
#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
|
|
#define CONFIG_BOOTCOMMAND "sf probe && sf read $kernel_load " \
|
|
"e0000 f00000 && bootm $kernel_load"
|
|
#else
|
|
#define CONFIG_BOOTCOMMAND "cp.b $kernel_start $kernel_load " \
|
|
"$kernel_size && bootm $kernel_load"
|
|
#endif
|
|
|
|
#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
|
|
#define MTDPARTS_DEFAULT "mtdparts=1550000.quadspi:2m(uboot)," \
|
|
"14m(free)"
|
|
#else
|
|
#define MTDPARTS_DEFAULT "mtdparts=60000000.nor:1m(nor_bank0_rcw)," \
|
|
"1m(nor_bank0_uboot),1m(nor_bank0_uboot_env)," \
|
|
"1m(nor_bank0_fman_uconde),40m(nor_bank0_fit)," \
|
|
"1m(nor_bank4_rcw),1m(nor_bank4_uboot)," \
|
|
"1m(nor_bank4_uboot_env),1m(nor_bank4_fman_ucode)," \
|
|
"40m(nor_bank4_fit);7e800000.flash:" \
|
|
"4m(nand_uboot),36m(nand_kernel)," \
|
|
"472m(nand_free);spi0.0:2m(uboot)," \
|
|
"14m(free)"
|
|
#endif
|
|
|
|
#include <asm/fsl_secure_boot.h>
|
|
|
|
#endif /* __LS1046AQDS_H__ */
|