a09fea1d28
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
53 lines
1.3 KiB
Plaintext
53 lines
1.3 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_ARCH_MX6=y
|
|
CONFIG_SYS_TEXT_BASE=0x17800000
|
|
CONFIG_SPL_GPIO_SUPPORT=y
|
|
CONFIG_SPL_LIBCOMMON_SUPPORT=y
|
|
CONFIG_SPL_LIBGENERIC_SUPPORT=y
|
|
CONFIG_TARGET_ZC5202=y
|
|
CONFIG_SPL_MMC_SUPPORT=y
|
|
CONFIG_SPL_SERIAL_SUPPORT=y
|
|
CONFIG_ENV_SIZE=0x2000
|
|
CONFIG_ENV_OFFSET=0x0
|
|
CONFIG_NR_DRAM_BANKS=1
|
|
CONFIG_SPL=y
|
|
CONFIG_SPL_LIBDISK_SUPPORT=y
|
|
CONFIG_SPL_SPI_FLASH_SUPPORT=y
|
|
CONFIG_SPL_SPI_SUPPORT=y
|
|
CONFIG_SPL_TEXT_BASE=0x00908000
|
|
CONFIG_DISTRO_DEFAULTS=y
|
|
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg,MX6Q"
|
|
CONFIG_BOOTDELAY=3
|
|
CONFIG_BOOTCOMMAND="run findfdt; run distro_bootcmd"
|
|
CONFIG_DEFAULT_FDT_FILE="imx6q-zc5202.dtb"
|
|
CONFIG_BOUNCE_BUFFER=y
|
|
CONFIG_BOARD_EARLY_INIT_F=y
|
|
CONFIG_SPL_FS_EXT4=y
|
|
CONFIG_SPL_I2C_SUPPORT=y
|
|
CONFIG_SPL_SPI_LOAD=y
|
|
CONFIG_SYS_SPI_U_BOOT_OFFS=0x10000
|
|
CONFIG_SPL_WATCHDOG_SUPPORT=y
|
|
CONFIG_CMD_MEMTEST=y
|
|
CONFIG_CMD_GPIO=y
|
|
CONFIG_CMD_I2C=y
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_PCI=y
|
|
CONFIG_CMD_SF=y
|
|
CONFIG_CMD_CACHE=y
|
|
CONFIG_CMD_EXT4_WRITE=y
|
|
CONFIG_ENV_IS_IN_MMC=y
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
|
|
CONFIG_SUPPORT_EMMC_BOOT=y
|
|
CONFIG_FSL_USDHC=y
|
|
CONFIG_SPI_FLASH=y
|
|
CONFIG_SF_DEFAULT_BUS=3
|
|
CONFIG_SF_DEFAULT_MODE=0
|
|
CONFIG_SF_DEFAULT_SPEED=20000000
|
|
CONFIG_SPI_FLASH_STMICRO=y
|
|
CONFIG_MII=y
|
|
CONFIG_PCI=y
|
|
CONFIG_SPI=y
|
|
CONFIG_MXC_SPI=y
|
|
CONFIG_OF_LIBFDT=y
|