a09fea1d28
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
58 lines
1.4 KiB
Plaintext
58 lines
1.4 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_SYS_BOARD="w400"
|
|
CONFIG_ARCH_MESON=y
|
|
CONFIG_SYS_TEXT_BASE=0x01000000
|
|
CONFIG_MESON_G12A=y
|
|
CONFIG_ENV_SIZE=0x2000
|
|
CONFIG_NR_DRAM_BANKS=1
|
|
CONFIG_DEBUG_UART_BASE=0xff803000
|
|
CONFIG_DEBUG_UART_CLOCK=24000000
|
|
CONFIG_IDENT_STRING=" khadas-vim3"
|
|
CONFIG_DEBUG_UART=y
|
|
CONFIG_OF_BOARD_SETUP=y
|
|
CONFIG_MISC_INIT_R=y
|
|
# CONFIG_DISPLAY_CPUINFO is not set
|
|
# CONFIG_CMD_BDI is not set
|
|
# CONFIG_CMD_IMI is not set
|
|
CONFIG_CMD_GPIO=y
|
|
# CONFIG_CMD_LOADS is not set
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_USB=y
|
|
CONFIG_CMD_USB_MASS_STORAGE=y
|
|
# CONFIG_CMD_SETEXPR is not set
|
|
CONFIG_CMD_REGULATOR=y
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_DEFAULT_DEVICE_TREE="meson-g12b-a311d-khadas-vim3"
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_NET_RANDOM_ETHADDR=y
|
|
CONFIG_DM_GPIO=y
|
|
CONFIG_DM_MMC=y
|
|
CONFIG_MMC_MESON_GX=y
|
|
CONFIG_PHY_REALTEK=y
|
|
CONFIG_DM_ETH=y
|
|
CONFIG_ETH_DESIGNWARE=y
|
|
CONFIG_MESON_G12A_USB_PHY=y
|
|
CONFIG_PINCTRL=y
|
|
CONFIG_PINCTRL_MESON_G12A=y
|
|
CONFIG_DM_REGULATOR=y
|
|
CONFIG_DM_REGULATOR_FIXED=y
|
|
CONFIG_DM_RESET=y
|
|
CONFIG_DEBUG_UART_MESON=y
|
|
CONFIG_DEBUG_UART_ANNOUNCE=y
|
|
CONFIG_DEBUG_UART_SKIP_INIT=y
|
|
CONFIG_MESON_SERIAL=y
|
|
CONFIG_USB=y
|
|
CONFIG_DM_USB=y
|
|
CONFIG_USB_XHCI_HCD=y
|
|
CONFIG_USB_XHCI_DWC3=y
|
|
CONFIG_USB_DWC3=y
|
|
# CONFIG_USB_DWC3_GADGET is not set
|
|
CONFIG_USB_DWC3_MESON_G12A=y
|
|
CONFIG_USB_GADGET=y
|
|
CONFIG_USB_GADGET_VENDOR_NUM=0x1b8e
|
|
CONFIG_USB_GADGET_PRODUCT_NUM=0xfada
|
|
CONFIG_USB_GADGET_DWC2_OTG=y
|
|
CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8=y
|
|
CONFIG_USB_GADGET_DOWNLOAD=y
|
|
CONFIG_OF_LIBFDT_OVERLAY=y
|