a09fea1d28
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
90 lines
2.1 KiB
Plaintext
90 lines
2.1 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_SPL_SYS_ICACHE_OFF=y
|
|
CONFIG_SPL_SYS_DCACHE_OFF=y
|
|
CONFIG_ARCH_IMX8=y
|
|
CONFIG_SYS_TEXT_BASE=0x80020000
|
|
CONFIG_SPL_GPIO_SUPPORT=y
|
|
CONFIG_SPL_LIBCOMMON_SUPPORT=y
|
|
CONFIG_SPL_LIBGENERIC_SUPPORT=y
|
|
CONFIG_SYS_MALLOC_F_LEN=0x4000
|
|
CONFIG_SPL_LOAD_IMX_CONTAINER=y
|
|
CONFIG_IMX_CONTAINER_CFG="board/freescale/imx8qxp_mek/uboot-container.cfg"
|
|
CONFIG_TARGET_IMX8QXP_MEK=y
|
|
CONFIG_SPL_MMC_SUPPORT=y
|
|
CONFIG_SPL_SERIAL_SUPPORT=y
|
|
CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
|
|
CONFIG_ENV_SIZE=0x1000
|
|
CONFIG_ENV_OFFSET=0x400000
|
|
CONFIG_NR_DRAM_BANKS=3
|
|
CONFIG_SPL=y
|
|
CONFIG_SPL_TEXT_BASE=0x100000
|
|
CONFIG_OF_SYSTEM_SETUP=y
|
|
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/imx8qxp_mek/imximage.cfg"
|
|
CONFIG_BOOTDELAY=3
|
|
CONFIG_LOG=y
|
|
CONFIG_SPL_BOARD_INIT=y
|
|
CONFIG_SPL_SYS_MALLOC_SIMPLE=y
|
|
CONFIG_SPL_SEPARATE_BSS=y
|
|
CONFIG_SPL_POWER_SUPPORT=y
|
|
CONFIG_SPL_POWER_DOMAIN=y
|
|
CONFIG_SPL_WATCHDOG_SUPPORT=y
|
|
CONFIG_HUSH_PARSER=y
|
|
CONFIG_CMD_CPU=y
|
|
# CONFIG_BOOTM_NETBSD is not set
|
|
# CONFIG_CMD_IMPORTENV is not set
|
|
CONFIG_CMD_CLK=y
|
|
CONFIG_CMD_DM=y
|
|
CONFIG_CMD_FUSE=y
|
|
CONFIG_CMD_GPIO=y
|
|
CONFIG_CMD_I2C=y
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_DHCP=y
|
|
CONFIG_CMD_MII=y
|
|
CONFIG_CMD_PING=y
|
|
CONFIG_CMD_CACHE=y
|
|
CONFIG_CMD_FAT=y
|
|
CONFIG_SPL_OF_CONTROL=y
|
|
CONFIG_DEFAULT_DEVICE_TREE="fsl-imx8qxp-mek"
|
|
CONFIG_ENV_IS_IN_MMC=y
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_SPL_DM=y
|
|
CONFIG_SPL_CLK=y
|
|
CONFIG_CLK_IMX8=y
|
|
CONFIG_CPU=y
|
|
CONFIG_DM_GPIO=y
|
|
CONFIG_MXC_GPIO=y
|
|
CONFIG_DM_PCA953X=y
|
|
CONFIG_DM_I2C=y
|
|
CONFIG_SYS_I2C_IMX_LPI2C=y
|
|
CONFIG_I2C_MUX=y
|
|
CONFIG_I2C_MUX_PCA954x=y
|
|
CONFIG_MISC=y
|
|
CONFIG_DM_MMC=y
|
|
CONFIG_SUPPORT_EMMC_BOOT=y
|
|
CONFIG_FSL_USDHC=y
|
|
CONFIG_PHYLIB=y
|
|
CONFIG_PHY_ADDR_ENABLE=y
|
|
CONFIG_PHY_ATHEROS=y
|
|
CONFIG_DM_ETH=y
|
|
CONFIG_PHY_GIGE=y
|
|
CONFIG_FEC_MXC_SHARE_MDIO=y
|
|
CONFIG_FEC_MXC_MDIO_BASE=0x5B040000
|
|
CONFIG_FEC_MXC=y
|
|
CONFIG_MII=y
|
|
CONFIG_PINCTRL=y
|
|
CONFIG_SPL_PINCTRL=y
|
|
CONFIG_PINCTRL_IMX8=y
|
|
CONFIG_POWER_DOMAIN=y
|
|
CONFIG_IMX8_POWER_DOMAIN=y
|
|
CONFIG_DM_REGULATOR=y
|
|
CONFIG_SPL_DM_REGULATOR=y
|
|
CONFIG_DM_REGULATOR_FIXED=y
|
|
CONFIG_DM_REGULATOR_GPIO=y
|
|
CONFIG_SPL_DM_REGULATOR_GPIO=y
|
|
CONFIG_DM_SERIAL=y
|
|
CONFIG_FSL_LPUART=y
|
|
CONFIG_DM_THERMAL=y
|
|
CONFIG_IMX_SCU_THERMAL=y
|
|
CONFIG_SPL_TINY_MEMSET=y
|
|
# CONFIG_EFI_LOADER is not set
|