56c4046038
This change allows more fine tuning of driver model based SPI support in
SPL and TPL. It is now possible to explicitly enable/disable the DM_SPI
support in SPL and TPL via Kconfig option.
Before this change it was necessary to use:
/* SPI Flash Configs */
#if defined(CONFIG_SPL_BUILD)
#undef CONFIG_DM_SPI
#undef CONFIG_DM_SPI_FLASH
#undef CONFIG_SPI_FLASH_MTD
#endif
in the ./include/configs/<board>.h, which is error prone and shall be
avoided when we strive to switch to Kconfig.
The goal of this patch:
Provide distinction for DM_SPI support in both U-Boot proper and SPL (TPL).
Valid use case is when U-Boot proper wants to use DM_SPI, but SPL must
still support non DM driver.
Another use case is the conversion of non DM/DTS SPI driver to support
DM/DTS. When such driver needs to work in both SPL and U-Boot proper, the
distinction is needed in Kconfig (also if SPL version of the driver
supports OF_PLATDATA).
In the end of the day one would have to support following use cases (in
single driver file - e.g. mxs_spi.c):
- U-Boot proper driver supporting DT/DTS
- U-Boot proper driver without DT/DTS support (deprecated)
- SPL driver without DT/DTS support
- SPL (and TPL) driver with DT/DTS (when the SoC has enough resources to
run full blown DT/DTS)
- SPL driver with DT/DTS and SPL_OF_PLATDATA (when one have constrained
environment with no fitImage and OF_LIBFDT support).
Some boards do require SPI support (with DM) in SPL (TPL) and some only
have DM_SPI{_FLASH} defined to allow compiling SPL.
This patch converts #ifdef CONFIG_DM_SPI* to #if CONFIG_IS_ENABLED(DM_SPI)
and provides corresponding defines in Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[trini: Fixup a few platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
66 lines
1.6 KiB
Plaintext
66 lines
1.6 KiB
Plaintext
CONFIG_X86=y
|
|
CONFIG_SYS_TEXT_BASE=0x1110000
|
|
CONFIG_SYS_MALLOC_F_LEN=0x1000
|
|
CONFIG_ENV_SIZE=0x40000
|
|
CONFIG_MAX_CPUS=2
|
|
CONFIG_SPL_DM_SPI=y
|
|
CONFIG_NR_DRAM_BANKS=8
|
|
CONFIG_DEBUG_UART_BASE=0x3f8
|
|
CONFIG_DEBUG_UART_CLOCK=1843200
|
|
CONFIG_SPL_TEXT_BASE=0xfffd0000
|
|
CONFIG_X86_RUN_64BIT=y
|
|
CONFIG_TARGET_QEMU_X86_64=y
|
|
CONFIG_DEBUG_UART=y
|
|
CONFIG_SMP=y
|
|
CONFIG_GENERATE_PIRQ_TABLE=y
|
|
CONFIG_GENERATE_MP_TABLE=y
|
|
CONFIG_GENERATE_ACPI_TABLE=y
|
|
CONFIG_X86_OFFSET_U_BOOT=0xfff00000
|
|
CONFIG_DISTRO_DEFAULTS=y
|
|
CONFIG_BUILD_ROM=y
|
|
CONFIG_FIT=y
|
|
CONFIG_SPL_LOAD_FIT=y
|
|
CONFIG_BOOTSTAGE=y
|
|
CONFIG_BOOTSTAGE_REPORT=y
|
|
CONFIG_SHOW_BOOT_PROGRESS=y
|
|
CONFIG_USE_BOOTARGS=y
|
|
CONFIG_BOOTARGS="root=/dev/sdb3 init=/sbin/init rootwait ro"
|
|
CONFIG_SYS_CONSOLE_INFO_QUIET=y
|
|
CONFIG_DISPLAY_BOARDINFO_LATE=y
|
|
CONFIG_LAST_STAGE_INIT=y
|
|
CONFIG_PCI_INIT_R=y
|
|
CONFIG_SPL_SYS_MALLOC_SIMPLE=y
|
|
CONFIG_SPL_CPU_SUPPORT=y
|
|
CONFIG_SPL_ENV_SUPPORT=y
|
|
CONFIG_SPL_DM_SPI_FLASH=y
|
|
CONFIG_SPL_NET_SUPPORT=y
|
|
CONFIG_SPL_PCI=y
|
|
CONFIG_SPL_PCH_SUPPORT=y
|
|
CONFIG_SPL_RTC_SUPPORT=y
|
|
CONFIG_CMD_CPU=y
|
|
CONFIG_CMD_BOOTEFI_SELFTEST=y
|
|
CONFIG_CMD_NVEDIT_EFI=y
|
|
CONFIG_CMD_IDE=y
|
|
CONFIG_CMD_SPI=y
|
|
CONFIG_CMD_USB=y
|
|
# CONFIG_CMD_SETEXPR is not set
|
|
# CONFIG_CMD_NFS is not set
|
|
CONFIG_CMD_TIME=y
|
|
CONFIG_CMD_QFW=y
|
|
CONFIG_CMD_BOOTSTAGE=y
|
|
CONFIG_CMD_EXT4_WRITE=y
|
|
CONFIG_DEFAULT_DEVICE_TREE="qemu-x86_i440fx"
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_REGMAP=y
|
|
CONFIG_SYSCON=y
|
|
CONFIG_CPU=y
|
|
CONFIG_NVME=y
|
|
CONFIG_SPL_DM_RTC=y
|
|
CONFIG_SPI=y
|
|
CONFIG_USB_KEYBOARD=y
|
|
CONFIG_FRAMEBUFFER_SET_VESA_MODE=y
|
|
CONFIG_FRAMEBUFFER_VESA_MODE_USER=y
|
|
CONFIG_FRAMEBUFFER_VESA_MODE=0x144
|
|
CONFIG_CONSOLE_SCROLL_LINES=5
|
|
# CONFIG_GZIP is not set
|