f1b1f77060
This converts the following to Kconfig: CONFIG_SPI This partly involves updating code that assumes that CONFIG_SPI implies things that are specific to the MPC8xx SPI driver. For now, just update the CONFIG tests. This also involves reworking the default for CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a reasonable default, as it does not cause any compile failures. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
83 lines
1.9 KiB
Plaintext
83 lines
1.9 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_ARCH_AT91=y
|
|
CONFIG_SYS_TEXT_BASE=0x26f00000
|
|
CONFIG_TARGET_SAMA5D4_XPLAINED=y
|
|
CONFIG_SPL_GPIO_SUPPORT=y
|
|
CONFIG_SPL_LIBCOMMON_SUPPORT=y
|
|
CONFIG_SPL_LIBGENERIC_SUPPORT=y
|
|
CONFIG_SYS_MALLOC_F_LEN=0x2000
|
|
CONFIG_SPL_MMC_SUPPORT=y
|
|
CONFIG_SPL_SERIAL_SUPPORT=y
|
|
CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
|
|
CONFIG_SPL_LIBDISK_SUPPORT=y
|
|
CONFIG_SPL=y
|
|
CONFIG_SPL_FAT_SUPPORT=y
|
|
CONFIG_DEFAULT_DEVICE_TREE="at91-sama5d4_xplained"
|
|
CONFIG_DEBUG_UART=y
|
|
CONFIG_ENV_VARS_UBOOT_CONFIG=y
|
|
CONFIG_FIT=y
|
|
CONFIG_SD_BOOT=y
|
|
CONFIG_BOOTDELAY=3
|
|
CONFIG_USE_BOOTARGS=y
|
|
CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk root=/dev/mmcblk0p2 rw rootwait"
|
|
# CONFIG_DISPLAY_BOARDINFO is not set
|
|
CONFIG_SPL_SEPARATE_BSS=y
|
|
CONFIG_HUSH_PARSER=y
|
|
CONFIG_CMD_BOOTZ=y
|
|
# CONFIG_CMD_IMI is not set
|
|
# CONFIG_CMD_FLASH is not set
|
|
# CONFIG_CMD_LOADS is not set
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_NAND=y
|
|
CONFIG_CMD_SF=y
|
|
CONFIG_CMD_USB=y
|
|
CONFIG_CMD_DHCP=y
|
|
CONFIG_CMD_PING=y
|
|
CONFIG_CMD_FAT=y
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_SPL_OF_CONTROL=y
|
|
CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-parent dma-names dmas"
|
|
CONFIG_ENV_IS_IN_FAT=y
|
|
CONFIG_DM=y
|
|
CONFIG_SPL_DM=y
|
|
CONFIG_CLK=y
|
|
CONFIG_SPL_CLK=y
|
|
CONFIG_CLK_AT91=y
|
|
CONFIG_AT91_UTMI=y
|
|
CONFIG_AT91_H32MX=y
|
|
CONFIG_DM_GPIO=y
|
|
CONFIG_AT91_GPIO=y
|
|
CONFIG_DM_I2C=y
|
|
CONFIG_SYS_I2C_AT91=y
|
|
CONFIG_I2C_EEPROM=y
|
|
CONFIG_DM_MMC=y
|
|
CONFIG_GENERIC_ATMEL_MCI=y
|
|
CONFIG_DM_SPI_FLASH=y
|
|
CONFIG_SPI_FLASH=y
|
|
CONFIG_SPI_FLASH_ATMEL=y
|
|
CONFIG_DM_ETH=y
|
|
CONFIG_MACB=y
|
|
CONFIG_PINCTRL=y
|
|
CONFIG_SPL_PINCTRL=y
|
|
CONFIG_PINCTRL_AT91=y
|
|
CONFIG_DM_SERIAL=y
|
|
CONFIG_DEBUG_UART_ATMEL=y
|
|
CONFIG_DEBUG_UART_BASE=0xfc00c000
|
|
CONFIG_DEBUG_UART_CLOCK=100000000
|
|
CONFIG_DEBUG_UART_BOARD_INIT=y
|
|
CONFIG_DEBUG_UART_ANNOUNCE=y
|
|
CONFIG_ATMEL_USART=y
|
|
CONFIG_SPI=y
|
|
CONFIG_DM_SPI=y
|
|
CONFIG_TIMER=y
|
|
CONFIG_SPL_TIMER=y
|
|
CONFIG_ATMEL_PIT_TIMER=y
|
|
CONFIG_USB=y
|
|
CONFIG_DM_USB=y
|
|
CONFIG_USB_EHCI_HCD=y
|
|
CONFIG_USB_STORAGE=y
|
|
CONFIG_USB_GADGET=y
|
|
CONFIG_USB_GADGET_ATMEL_USBA=y
|
|
CONFIG_DM_VIDEO=y
|
|
CONFIG_ATMEL_HLCD=y
|