56c4046038
This change allows more fine tuning of driver model based SPI support in
SPL and TPL. It is now possible to explicitly enable/disable the DM_SPI
support in SPL and TPL via Kconfig option.
Before this change it was necessary to use:
/* SPI Flash Configs */
#if defined(CONFIG_SPL_BUILD)
#undef CONFIG_DM_SPI
#undef CONFIG_DM_SPI_FLASH
#undef CONFIG_SPI_FLASH_MTD
#endif
in the ./include/configs/<board>.h, which is error prone and shall be
avoided when we strive to switch to Kconfig.
The goal of this patch:
Provide distinction for DM_SPI support in both U-Boot proper and SPL (TPL).
Valid use case is when U-Boot proper wants to use DM_SPI, but SPL must
still support non DM driver.
Another use case is the conversion of non DM/DTS SPI driver to support
DM/DTS. When such driver needs to work in both SPL and U-Boot proper, the
distinction is needed in Kconfig (also if SPL version of the driver
supports OF_PLATDATA).
In the end of the day one would have to support following use cases (in
single driver file - e.g. mxs_spi.c):
- U-Boot proper driver supporting DT/DTS
- U-Boot proper driver without DT/DTS support (deprecated)
- SPL driver without DT/DTS support
- SPL (and TPL) driver with DT/DTS (when the SoC has enough resources to
run full blown DT/DTS)
- SPL driver with DT/DTS and SPL_OF_PLATDATA (when one have constrained
environment with no fitImage and OF_LIBFDT support).
Some boards do require SPI support (with DM) in SPL (TPL) and some only
have DM_SPI{_FLASH} defined to allow compiling SPL.
This patch converts #ifdef CONFIG_DM_SPI* to #if CONFIG_IS_ENABLED(DM_SPI)
and provides corresponding defines in Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[trini: Fixup a few platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
117 lines
2.9 KiB
Plaintext
117 lines
2.9 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_ARCH_OMAP2PLUS=y
|
|
CONFIG_SPL_GPIO_SUPPORT=y
|
|
CONFIG_SPL_LIBCOMMON_SUPPORT=y
|
|
CONFIG_SPL_LIBGENERIC_SUPPORT=y
|
|
CONFIG_SYS_MALLOC_F_LEN=0x2000
|
|
CONFIG_ENV_SIZE=0x10000
|
|
CONFIG_ENV_OFFSET=0x20000
|
|
CONFIG_ENV_SECT_SIZE=0x10000
|
|
CONFIG_SYS_SPI_U_BOOT_OFFS=0x40000
|
|
CONFIG_DM_GPIO=y
|
|
CONFIG_SPL_DM_SPI=y
|
|
CONFIG_AM33XX=y
|
|
CONFIG_SYS_MPUCLK=600
|
|
CONFIG_TARGET_BRSMARC1=y
|
|
CONFIG_SPL_SERIAL_SUPPORT=y
|
|
CONFIG_SPL_SYS_MALLOC_F_LEN=0x4000
|
|
CONFIG_SPL=y
|
|
CONFIG_ENV_OFFSET_REDUND=0x30000
|
|
CONFIG_SPL_SPI_FLASH_SUPPORT=y
|
|
CONFIG_SPL_SPI_SUPPORT=y
|
|
# CONFIG_EXPERT is not set
|
|
# CONFIG_FIT is not set
|
|
CONFIG_OF_BOARD_SETUP=y
|
|
CONFIG_BOOTDELAY=0
|
|
CONFIG_USE_BOOTCOMMAND=y
|
|
CONFIG_BOOTCOMMAND="run b_default"
|
|
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
|
|
CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
|
|
CONFIG_SYS_CONSOLE_INFO_QUIET=y
|
|
CONFIG_VERSION_VARIABLE=y
|
|
# CONFIG_DISPLAY_CPUINFO is not set
|
|
# CONFIG_DISPLAY_BOARDINFO is not set
|
|
CONFIG_BOARD_TYPES=y
|
|
CONFIG_ARCH_MISC_INIT=y
|
|
# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
|
|
CONFIG_SPL_SYS_MALLOC_SIMPLE=y
|
|
CONFIG_SPL_SEPARATE_BSS=y
|
|
# CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set
|
|
CONFIG_SPL_I2C_SUPPORT=y
|
|
# CONFIG_SPL_NAND_SUPPORT is not set
|
|
CONFIG_SPL_DM_SPI_FLASH=y
|
|
CONFIG_SPL_POWER_SUPPORT=y
|
|
CONFIG_SPL_SPI_LOAD=y
|
|
CONFIG_SPL_YMODEM_SUPPORT=y
|
|
CONFIG_HUSH_PARSER=y
|
|
# CONFIG_CMD_BOOTD is not set
|
|
CONFIG_CMD_BOOTZ=y
|
|
# CONFIG_BOOTM_NETBSD is not set
|
|
# CONFIG_BOOTM_PLAN9 is not set
|
|
# CONFIG_BOOTM_RTEMS is not set
|
|
# CONFIG_CMD_IMI is not set
|
|
# CONFIG_CMD_XIMG is not set
|
|
# CONFIG_CMD_EDITENV is not set
|
|
# CONFIG_CMD_CRC32 is not set
|
|
CONFIG_CMD_CLK=y
|
|
# CONFIG_CMD_FLASH is not set
|
|
CONFIG_CMD_GPIO=y
|
|
CONFIG_CMD_I2C=y
|
|
# CONFIG_CMD_LOADS is not set
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_SPI=y
|
|
CONFIG_CMD_USB=y
|
|
# CONFIG_CMD_ITEST is not set
|
|
CONFIG_CMD_DHCP=y
|
|
# CONFIG_CMD_NFS is not set
|
|
CONFIG_CMD_MII=y
|
|
CONFIG_CMD_PING=y
|
|
CONFIG_CMD_TIME=y
|
|
CONFIG_CMD_EXT4=y
|
|
CONFIG_CMD_EXT4_WRITE=y
|
|
CONFIG_CMD_FAT=y
|
|
CONFIG_CMD_FS_GENERIC=y
|
|
# CONFIG_SPL_DOS_PARTITION is not set
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_SPL_OF_CONTROL=y
|
|
CONFIG_DEFAULT_DEVICE_TREE="am335x-brsmarc1"
|
|
CONFIG_ENV_IS_IN_SPI_FLASH=y
|
|
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_NET_RANDOM_ETHADDR=y
|
|
CONFIG_NETCONSOLE=y
|
|
CONFIG_DM=y
|
|
CONFIG_SPL_DM=y
|
|
CONFIG_SPL_DM_SEQ_ALIAS=y
|
|
# CONFIG_OF_TRANSLATE is not set
|
|
# CONFIG_SPL_BLK is not set
|
|
CONFIG_DM_I2C=y
|
|
CONFIG_MISC=y
|
|
CONFIG_DM_MMC=y
|
|
CONFIG_MMC_OMAP_HS=y
|
|
CONFIG_MTD=y
|
|
CONFIG_DM_SPI_FLASH=y
|
|
CONFIG_SF_DEFAULT_SPEED=24000000
|
|
CONFIG_SPI_FLASH_SPANSION=y
|
|
CONFIG_SPI_FLASH_STMICRO=y
|
|
CONFIG_SPI_FLASH_WINBOND=y
|
|
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
|
|
CONFIG_PHY_NATSEMI=y
|
|
CONFIG_DM_ETH=y
|
|
CONFIG_DRIVER_TI_CPSW=y
|
|
CONFIG_DM_SERIAL=y
|
|
CONFIG_SPI=y
|
|
CONFIG_DM_SPI=y
|
|
CONFIG_OMAP3_SPI=y
|
|
CONFIG_USB=y
|
|
CONFIG_DM_USB=y
|
|
CONFIG_USB_MUSB_HOST=y
|
|
CONFIG_USB_MUSB_GADGET=y
|
|
CONFIG_USB_MUSB_TI=y
|
|
CONFIG_USB_STORAGE=y
|
|
CONFIG_USB_GADGET=y
|
|
CONFIG_SPL_TINY_MEMSET=y
|
|
CONFIG_SHA1=y
|
|
CONFIG_SHA256=y
|
|
# CONFIG_EFI_LOADER is not set
|