0a3689cb86
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
69 lines
1.6 KiB
Plaintext
69 lines
1.6 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_ARCH_MX6=y
|
|
CONFIG_SYS_TEXT_BASE=0x87800000
|
|
CONFIG_SYS_MALLOC_LEN=0x1000000
|
|
CONFIG_SPL_GPIO=y
|
|
CONFIG_SPL_LIBCOMMON_SUPPORT=y
|
|
CONFIG_SPL_LIBGENERIC_SUPPORT=y
|
|
CONFIG_NR_DRAM_BANKS=1
|
|
CONFIG_ENV_SIZE=0x20000
|
|
CONFIG_ENV_OFFSET=0x400000
|
|
CONFIG_MX6UL=y
|
|
CONFIG_TARGET_MX6UL_ENGICAM=y
|
|
CONFIG_DEFAULT_DEVICE_TREE="imx6ul-isiot-nand"
|
|
CONFIG_SPL_TEXT_BASE=0x00908000
|
|
CONFIG_SPL_SERIAL=y
|
|
CONFIG_SPL=y
|
|
# CONFIG_CMD_BMODE is not set
|
|
CONFIG_SYS_MEMTEST_START=0x80000000
|
|
CONFIG_SYS_MEMTEST_END=0x88000000
|
|
CONFIG_FIT=y
|
|
CONFIG_FIT_SIGNATURE=y
|
|
CONFIG_FIT_VERBOSE=y
|
|
CONFIG_LEGACY_IMAGE_FORMAT=y
|
|
CONFIG_SUPPORT_RAW_INITRD=y
|
|
CONFIG_BOOTDELAY=3
|
|
CONFIG_USE_BOOTCOMMAND=y
|
|
CONFIG_BOOTCOMMAND="run $modeboot"
|
|
CONFIG_SPL_DMA=y
|
|
CONFIG_SPL_NAND_SUPPORT=y
|
|
CONFIG_SPL_WATCHDOG=y
|
|
CONFIG_HUSH_PARSER=y
|
|
CONFIG_SYS_PROMPT="isiotmx6ul> "
|
|
CONFIG_CRC32_VERIFY=y
|
|
CONFIG_CMD_MEMTEST=y
|
|
CONFIG_CMD_GPIO=y
|
|
CONFIG_CMD_I2C=y
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_MII=y
|
|
CONFIG_CMD_PING=y
|
|
CONFIG_CMD_CACHE=y
|
|
CONFIG_CMD_EXT4=y
|
|
CONFIG_CMD_EXT4_WRITE=y
|
|
CONFIG_CMD_FAT=y
|
|
CONFIG_CMD_FS_GENERIC=y
|
|
CONFIG_CMD_MTDPARTS=y
|
|
CONFIG_MTDIDS_DEFAULT="nand0=gpmi-nand"
|
|
CONFIG_MTDPARTS_DEFAULT="mtdparts=gpmi-nand:2m(spl),2m(uboot),1m(env),8m(kernel),1m(dtb),-(rootfs)"
|
|
CONFIG_CMD_UBI=y
|
|
CONFIG_ENV_OVERWRITE=y
|
|
CONFIG_ENV_IS_IN_NAND=y
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_BOUNCE_BUFFER=y
|
|
CONFIG_SYS_I2C_MXC=y
|
|
CONFIG_FSL_USDHC=y
|
|
CONFIG_MTD=y
|
|
CONFIG_MTD_RAW_NAND=y
|
|
CONFIG_NAND_MXS=y
|
|
CONFIG_SYS_NAND_ONFI_DETECTION=y
|
|
CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y
|
|
CONFIG_SYS_NAND_U_BOOT_OFFS=0x200000
|
|
CONFIG_PHYLIB=y
|
|
CONFIG_PHY_SMSC=y
|
|
CONFIG_FEC_MXC=y
|
|
CONFIG_MII=y
|
|
CONFIG_PINCTRL=y
|
|
CONFIG_PINCTRL_IMX6=y
|
|
CONFIG_MXC_UART=y
|
|
CONFIG_IMX_THERMAL=y
|