u-boot/include/axp209.h
Andre Przywara 78592c094e pmic: axp: define ALDO_IN startup bit
Most AXP PMICs feature a "startup source" register, which keeps
information about how the PMIC started operation. Bit 0 in there means
it has been started by "plugging in the power cable".

Define a symbol in each PMIC's header file to be able to use that
register and bit later on.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-01-30 01:25:00 +00:00

90 lines
2.8 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2012 Henrik Nordstrom <henrik@henriknordstrom.net>
*/
#include <linux/bitops.h>
enum axp209_reg {
AXP209_POWER_STATUS = 0x00,
AXP209_CHIP_VERSION = 0x03,
AXP209_OUTPUT_CTRL = 0x12,
AXP209_DCDC2_VOLTAGE = 0x23,
AXP209_VRC_DCDC2_LDO3 = 0x25,
AXP209_DCDC3_VOLTAGE = 0x27,
AXP209_LDO24_VOLTAGE = 0x28,
AXP209_LDO3_VOLTAGE = 0x29,
AXP209_IRQ_ENABLE1 = 0x40,
AXP209_IRQ_ENABLE2 = 0x41,
AXP209_IRQ_ENABLE3 = 0x42,
AXP209_IRQ_ENABLE4 = 0x43,
AXP209_IRQ_ENABLE5 = 0x44,
AXP209_IRQ_STATUS5 = 0x4c,
AXP209_SHUTDOWN = 0x32,
};
#define AXP209_POWER_STATUS_ON_BY_DC BIT(0)
#define AXP209_POWER_STATUS_VBUS_USABLE BIT(4)
#define AXP209_CHIP_VERSION_MASK 0x0f
#define AXP209_OUTPUT_CTRL_EXTEN BIT(0)
#define AXP209_OUTPUT_CTRL_DCDC3 BIT(1)
#define AXP209_OUTPUT_CTRL_LDO2 BIT(2)
#define AXP209_OUTPUT_CTRL_LDO4 BIT(3)
#define AXP209_OUTPUT_CTRL_DCDC2 BIT(4)
#define AXP209_OUTPUT_CTRL_LDO3 BIT(6)
/*
* AXP209 datasheet contains wrong information about LDO3 VRC:
* - VRC is actually enabled when BIT(1) is True
* - VRC is actually not enabled by default (BIT(3) = 0 after reset)
*/
#define AXP209_VRC_LDO3_EN BIT(3)
#define AXP209_VRC_DCDC2_EN BIT(2)
#define AXP209_VRC_LDO3_800uV_uS (BIT(1) | AXP209_VRC_LDO3_EN)
#define AXP209_VRC_LDO3_1600uV_uS AXP209_VRC_LDO3_EN
#define AXP209_VRC_DCDC2_800uV_uS (BIT(0) | AXP209_VRC_DCDC2_EN)
#define AXP209_VRC_DCDC2_1600uV_uS AXP209_VRC_DCDC2_EN
#define AXP209_VRC_LDO3_MASK 0xa
#define AXP209_VRC_DCDC2_MASK 0x5
#define AXP209_VRC_DCDC2_SLOPE_SET(reg, cfg) \
(((reg) & ~AXP209_VRC_DCDC2_MASK) | \
((cfg) & AXP209_VRC_DCDC2_MASK))
#define AXP209_VRC_LDO3_SLOPE_SET(reg, cfg) \
(((reg) & ~AXP209_VRC_LDO3_MASK) | \
((cfg) & AXP209_VRC_LDO3_MASK))
#define AXP209_LDO24_LDO2_MASK 0xf0
#define AXP209_LDO24_LDO4_MASK 0x0f
#define AXP209_LDO24_LDO2_SET(reg, cfg) \
(((reg) & ~AXP209_LDO24_LDO2_MASK) | \
(((cfg) << 4) & AXP209_LDO24_LDO2_MASK))
#define AXP209_LDO24_LDO4_SET(reg, cfg) \
(((reg) & ~AXP209_LDO24_LDO4_MASK) | \
(((cfg) << 0) & AXP209_LDO24_LDO4_MASK))
#define AXP209_LDO3_VOLTAGE_FROM_LDO3IN BIT(7)
#define AXP209_LDO3_VOLTAGE_MASK 0x7f
#define AXP209_LDO3_VOLTAGE_SET(x) ((x) & AXP209_LDO3_VOLTAGE_MASK)
#define AXP209_IRQ5_PEK_UP BIT(6)
#define AXP209_IRQ5_PEK_DOWN BIT(5)
#define AXP209_POWEROFF BIT(7)
/* For axp_gpio.c */
#ifdef CONFIG_AXP209_POWER
#define AXP_POWER_STATUS 0x00
#define AXP_POWER_STATUS_ALDO_IN BIT(0)
#define AXP_POWER_STATUS_VBUS_PRESENT BIT(5)
#define AXP_GPIO0_CTRL 0x90
#define AXP_GPIO1_CTRL 0x92
#define AXP_GPIO2_CTRL 0x93
#define AXP_GPIO_CTRL_OUTPUT_LOW 0x00 /* Drive pin low */
#define AXP_GPIO_CTRL_OUTPUT_HIGH 0x01 /* Drive pin high */
#define AXP_GPIO_CTRL_INPUT 0x02 /* Input */
#define AXP_GPIO_STATE 0x94
#define AXP_GPIO_STATE_OFFSET 4
#endif