08574ed339
This converts the following to Kconfig: CONFIG_SYS_MONITOR_LEN To do this, we set a default of 0 for everyone because there are a number of cases where we define CONFIG_SYS_MONITOR_LEN but the only impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN + CONFIG_ENV_SIZE, so we must continue to allow all boards to set this value. Update the SPL code to use 200 KB as the default raw U-Boot size directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
113 lines
2.7 KiB
Plaintext
113 lines
2.7 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_SKIP_LOWLEVEL_INIT=y
|
|
CONFIG_GIC_V3_ITS=y
|
|
CONFIG_TARGET_LX2160ARDB=y
|
|
CONFIG_TFABOOT=y
|
|
CONFIG_TEXT_BASE=0x82000000
|
|
CONFIG_SYS_MALLOC_LEN=0x202000
|
|
CONFIG_SYS_MALLOC_F_LEN=0x6000
|
|
CONFIG_NR_DRAM_BANKS=3
|
|
CONFIG_ENV_SIZE=0x2000
|
|
CONFIG_ENV_OFFSET=0x500000
|
|
CONFIG_ENV_SECT_SIZE=0x20000
|
|
CONFIG_DM_GPIO=y
|
|
CONFIG_DEFAULT_DEVICE_TREE="fsl-lx2160a-rdb"
|
|
CONFIG_EMC2305=y
|
|
CONFIG_FSPI_AHB_EN_4BYTE=y
|
|
CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y
|
|
CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y
|
|
CONFIG_ENV_ADDR=0x20500000
|
|
CONFIG_AHCI=y
|
|
CONFIG_OF_BOARD_FIXUP=y
|
|
CONFIG_FSL_USE_PCA9547_MUX=y
|
|
CONFIG_VID=y
|
|
CONFIG_VID_FLS_ENV="lx2160ardb_vdd_mv"
|
|
CONFIG_VOL_MONITOR_LTC3882_READ=y
|
|
CONFIG_VOL_MONITOR_LTC3882_SET=y
|
|
CONFIG_SYS_FSL_NUM_CC_PLLS=4
|
|
CONFIG_FSL_QIXIS=y
|
|
CONFIG_REMAKE_ELF=y
|
|
CONFIG_SYS_MONITOR_LEN=958464
|
|
CONFIG_MP=y
|
|
CONFIG_FIT_VERBOSE=y
|
|
CONFIG_OF_BOARD_SETUP=y
|
|
CONFIG_OF_STDOUT_VIA_ALIAS=y
|
|
CONFIG_DYNAMIC_SYS_CLK_FREQ=y
|
|
CONFIG_BOOTDELAY=10
|
|
CONFIG_USE_BOOTARGS=y
|
|
CONFIG_BOOTARGS="console=ttyAMA0,115200 root=/dev/ram0 earlycon=pl011,mmio32,0x21c0000 ramdisk_size=0x2000000 default_hugepagesz=1024m hugepagesz=1024m hugepages=2 pci=pcie_bus_perf"
|
|
CONFIG_MISC_INIT_R=y
|
|
CONFIG_RESET_PHY_R=y
|
|
CONFIG_SYS_MAXARGS=64
|
|
CONFIG_SYS_PBSIZE=532
|
|
CONFIG_CMD_GREPENV=y
|
|
CONFIG_CMD_NVEDIT_EFI=y
|
|
CONFIG_CMD_EEPROM=y
|
|
CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=3
|
|
CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
|
|
CONFIG_CMD_DM=y
|
|
CONFIG_CMD_GPIO=y
|
|
CONFIG_CMD_GPT=y
|
|
CONFIG_CMD_I2C=y
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_PCI=y
|
|
CONFIG_CMD_USB=y
|
|
CONFIG_CMD_CACHE=y
|
|
CONFIG_CMD_EFIDEBUG=y
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_ENV_OVERWRITE=y
|
|
CONFIG_ENV_IS_IN_MMC=y
|
|
CONFIG_ENV_IS_IN_SPI_FLASH=y
|
|
CONFIG_USE_ETHPRIME=y
|
|
CONFIG_ETHPRIME="DPMAC1@xgmii"
|
|
CONFIG_NET_RANDOM_ETHADDR=y
|
|
CONFIG_SATA=y
|
|
CONFIG_SATA_CEVA=y
|
|
CONFIG_FSL_CAAM=y
|
|
CONFIG_DYNAMIC_DDR_CLK_FREQ=y
|
|
CONFIG_DIMM_SLOTS_PER_CTLR=2
|
|
CONFIG_DDR_ECC=y
|
|
CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
|
|
CONFIG_SYS_FSL_DDR_INTLV_256B=y
|
|
CONFIG_MPC8XXX_GPIO=y
|
|
CONFIG_DM_I2C=y
|
|
CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
|
|
CONFIG_SYS_I2C_EEPROM_ADDR=0x57
|
|
CONFIG_SUPPORT_EMMC_RPMB=y
|
|
CONFIG_MMC_HS400_SUPPORT=y
|
|
CONFIG_FSL_ESDHC=y
|
|
CONFIG_MTD=y
|
|
CONFIG_DM_SPI_FLASH=y
|
|
CONFIG_SPI_FLASH_STMICRO=y
|
|
CONFIG_SPI_FLASH_MT35XU=y
|
|
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
|
|
CONFIG_PHYLIB=y
|
|
CONFIG_PHY_AQUANTIA=y
|
|
CONFIG_PHY_ATHEROS=y
|
|
CONFIG_PHY_CORTINA=y
|
|
CONFIG_SYS_CORTINA_NO_FW_UPLOAD=y
|
|
CONFIG_FSL_MEMAC=y
|
|
CONFIG_SYS_MEMAC_LITTLE_ENDIAN=y
|
|
CONFIG_E1000=y
|
|
CONFIG_MII=y
|
|
CONFIG_NVME_PCI=y
|
|
CONFIG_PCI=y
|
|
CONFIG_PCIE_LAYERSCAPE_RC=y
|
|
CONFIG_PCIE_LAYERSCAPE_GEN4=y
|
|
CONFIG_DM_RTC=y
|
|
CONFIG_RTC_PCF2127=y
|
|
CONFIG_DM_SCSI=y
|
|
CONFIG_DM_SERIAL=y
|
|
CONFIG_PL01X_SERIAL=y
|
|
CONFIG_SPI=y
|
|
CONFIG_DM_SPI=y
|
|
CONFIG_NXP_FSPI=y
|
|
CONFIG_TEE=y
|
|
CONFIG_OPTEE=y
|
|
CONFIG_USB=y
|
|
CONFIG_USB_XHCI_HCD=y
|
|
CONFIG_USB_XHCI_DWC3=y
|
|
CONFIG_USB_MAX_CONTROLLER_COUNT=2
|
|
CONFIG_EFI_MM_COMM_TEE=y
|
|
CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
|