u-boot/configs/at91sam9263ek_norflash_boot_defconfig
Tom Rini 98fbad631f Convert CONFIG_FLASH_SHOW_PROGRESS to Kconfig
This converts the following to Kconfig:
   CONFIG_FLASH_SHOW_PROGRESS

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-12-22 10:31:48 -05:00

74 lines
1.7 KiB
Plaintext

CONFIG_ARM=y
CONFIG_ARCH_CPU_INIT=y
CONFIG_ARCH_AT91=y
CONFIG_TEXT_BASE=0x0000000
CONFIG_SYS_MALLOC_LEN=0x50000
CONFIG_TARGET_AT91SAM9263EK=y
CONFIG_ATMEL_LEGACY=y
CONFIG_SYS_USE_NORFLASH=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x10000
CONFIG_ENV_SECT_SIZE=0x10000
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="at91sam9263ek"
CONFIG_SYS_PROMPT="U-Boot> "
CONFIG_DEBUG_UART_BASE=0xffffee00
CONFIG_DEBUG_UART_CLOCK=100000000
CONFIG_DEBUG_UART_BOARD_INIT=y
CONFIG_SYS_LOAD_ADDR=0x22000000
CONFIG_ENV_ADDR=0x107E0000
CONFIG_DEBUG_UART=y
CONFIG_SYS_MONITOR_LEN=262144
CONFIG_SYS_MONITOR_BASE=0x10000000
CONFIG_BOOTDELAY=3
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_RESET_PHY_R=y
CONFIG_HUSH_PARSER=y
CONFIG_SYS_CBSIZE=256
CONFIG_SYS_PBSIZE=281
# CONFIG_CMD_BDI is not set
CONFIG_CMD_BOOTZ=y
# CONFIG_CMD_IMI is not set
# CONFIG_CMD_LOADS is not set
CONFIG_CMD_MMC=y
CONFIG_CMD_NAND=y
# CONFIG_CMD_SOURCE is not set
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_BOOTP_BOOTFILESIZE=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_ENV_ADDR_REDUND=0x107D0000
CONFIG_CLK=y
CONFIG_CLK_AT91=y
CONFIG_AT91_GPIO=y
CONFIG_GENERIC_ATMEL_MCI=y
CONFIG_MTD=y
CONFIG_MTD_NOR_FLASH=y
CONFIG_FLASH_CFI_DRIVER=y
CONFIG_FLASH_SHOW_PROGRESS=0
CONFIG_SYS_FLASH_CFI=y
CONFIG_SYS_MAX_FLASH_SECT=256
CONFIG_MTD_RAW_NAND=y
CONFIG_NAND_ATMEL=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH_ATMEL=y
CONFIG_SPI_FLASH_DATAFLASH=y
CONFIG_MACB=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_AT91=y
CONFIG_DM_SERIAL=y
CONFIG_DEBUG_UART_ANNOUNCE=y
CONFIG_ATMEL_USART=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_TIMER=y
CONFIG_ATMEL_PIT_TIMER=y
CONFIG_USB=y
CONFIG_SYS_USB_OHCI_SLOT_NAME="at91sam9263"
CONFIG_USB_ATMEL=y