401d1c4f5d
Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include <asm/global_data.h> at all, so remove that include. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
95 lines
1.9 KiB
C
95 lines
1.9 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) 2009-2012
|
|
* Wojciech Dubowik <wojciech.dubowik@neratec.com>
|
|
* Luka Perkov <luka@openwrt.org>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <init.h>
|
|
#include <miiphy.h>
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/soc.h>
|
|
#include <asm/arch/mpp.h>
|
|
#include <asm/global_data.h>
|
|
#include "iconnect.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
/*
|
|
* default gpio configuration
|
|
* There are maximum 64 gpios controlled through 2 sets of registers
|
|
* the below configuration configures mainly initial LED status
|
|
*/
|
|
mvebu_config_gpio(ICONNECT_OE_VAL_LOW,
|
|
ICONNECT_OE_VAL_HIGH,
|
|
ICONNECT_OE_LOW, ICONNECT_OE_HIGH);
|
|
|
|
/* Multi-Purpose Pins Functionality configuration */
|
|
static const u32 kwmpp_config[] = {
|
|
MPP0_NF_IO2,
|
|
MPP1_NF_IO3,
|
|
MPP2_NF_IO4,
|
|
MPP3_NF_IO5,
|
|
MPP4_NF_IO6,
|
|
MPP5_NF_IO7,
|
|
MPP6_SYSRST_OUTn, /* Reset signal */
|
|
MPP7_GPO,
|
|
MPP8_TW_SDA, /* I2C */
|
|
MPP9_TW_SCK, /* I2C */
|
|
MPP10_UART0_TXD,
|
|
MPP11_UART0_RXD,
|
|
MPP12_GPO, /* Reset button */
|
|
MPP13_SD_CMD,
|
|
MPP14_SD_D0,
|
|
MPP15_SD_D1,
|
|
MPP16_SD_D2,
|
|
MPP17_SD_D3,
|
|
MPP18_NF_IO0,
|
|
MPP19_NF_IO1,
|
|
MPP20_GE1_0,
|
|
MPP21_GE1_1,
|
|
MPP22_GE1_2,
|
|
MPP23_GE1_3,
|
|
MPP24_GE1_4,
|
|
MPP25_GE1_5,
|
|
MPP26_GE1_6,
|
|
MPP27_GE1_7,
|
|
MPP28_GPIO,
|
|
MPP29_GPIO,
|
|
MPP30_GE1_10,
|
|
MPP31_GE1_11,
|
|
MPP32_GE1_12,
|
|
MPP33_GE1_13,
|
|
MPP34_GE1_14,
|
|
MPP35_GPIO, /* OTB button */
|
|
MPP36_AUDIO_SPDIFI,
|
|
MPP37_AUDIO_SPDIFO,
|
|
MPP38_GPIO,
|
|
MPP39_TDM_SPI_CS0,
|
|
MPP40_TDM_SPI_SCK,
|
|
MPP41_GPIO, /* LED brightness */
|
|
MPP42_GPIO, /* LED power (blue) */
|
|
MPP43_GPIO, /* LED power (red) */
|
|
MPP44_GPIO, /* LED USB 1 */
|
|
MPP45_GPIO, /* LED USB 2 */
|
|
MPP46_GPIO, /* LED USB 3 */
|
|
MPP47_GPIO, /* LED USB 4 */
|
|
MPP48_GPIO, /* LED OTB */
|
|
MPP49_GPIO,
|
|
0
|
|
};
|
|
kirkwood_mpp_conf(kwmpp_config, NULL);
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
/* adress of boot parameters */
|
|
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
|
|
|
|
return 0;
|
|
}
|