When rtl_recv() of rtl8169 is called, OWNbit of status register
is not enable occasionally.
rtl_recv() doesn't work normally when the driver doesn't do
appropriate processing.
This patch fix this problem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
the dts file basenames were updated in linux - this helps avoid
inadvertently loading any old dtbs laying around.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
allow u-boot to recover (and, e.g., switch to another interface) in the
case where a PHY does not report autonegotiation is complete within its
two second timeout value.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The taihu board used gpio_read_out_bit which reads the output register and not
the pin state.
Signed-off-by: Markus Brunner <super.firetwister@gmail.com>
1. Make the CSB bus pipeline depth as 4, and enable
the repeat mode;
2. Raise the eTSEC emergency priority;
3. Use the highest IP blocks clock.
Signed-off-by: Dave Liu <daveliu@freescale.com>
The latter version stops when "run load" fails for whatever reasons
rendering the combination *a lot* more secure.
Signed-off-by: Detlev Zundel <dzu@denx.de>
This patch fixes a problem seen on PPC4xx boards, when no MAC address is
defined. Then no ethernet interface is available but a simple "tftp"
command will return without any error message which is quite confusing.
Signed-off-by: Stefan Roese <sr@denx.de>
Many of the spd.h #includers don't need it,
and wanted to have spd_sdram() declared instead.
Since they didn't get that, some also had open
coded extern declarations of it instead or as well.
Fix it all up by using spd_sdram.h where needed.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
This patch fixes a problem seen on PPC4xx boards, when no MAC address is
defined. Then no ethernet interface is available but a simple "tftp"
command will return without any error message which is quite confusing.
Signed-off-by: Stefan Roese <sr@denx.de>
Commit 5013c09f (Makefile: cleanup "clean" target) introduced a
problem for out-of-tree builds which caused "make clean" to fail.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Every now and then a Sequoia board (or equivalent hardware) had
problems connecting to a Gigabit capable network interface.
There were differences in the PHY setup between Linux and U-Boot.
This patch fixes the problem. Apparently "remote fault" is being set,
which signals to some devices (on the other end of the cable) that a
fault has occurred, while other devices ignore it. I believe the RF bit
was causing the issue, but I removed T4 also, to match up with Linux.
Signed-off-by: Mike Nuss <mike@terascala.com>
Fix a typo in qe_upload_firmware() that prevented uploading firmware on
systems with more than one RISC core.
Signed-off-by: Timur Tabi <timur@freescale.com>
If I try to "cp.b <ram> <dataflash>", u-boot selects normal flash
routines instead of dataflash. This is because it checks "if source
address is not dataflash" instead of target address.
Signed-off-by: Kim B. Heino <Kim.Heino@bluegiga.com>
This fixes the cluster size tests in the FAT32 file system.
The current implementation of VFAT support doesn't work if the
referred cluster has an offset > 16bit representation, causing
"fatload" and "fatls" commands etc. to fail.
Signed-off-by: michael trimarchi <trimarchi@gandalf.sssup.it>
The 405EZ only supports 512 bytes of rx-/tx-fifo EMAC sizes. But
currently 4k/2k is configured. This patch fixes this issue.
Thanks to Thomas Kindler <tkindler@lenord.de> for pointing this out.
Signed-off-by: Stefan Roese <sr@denx.de>
Fix alignment fault on ARM when running modules. With out an explicit
linker file gcc4.2.1 will half word align __bss_start's value. The word
dereference will crash hello_world.
signed-off-by Richard Woodruff <r-woodruff2@ti.com>
erratum 5.6 states the autoneg completion bit is functional only if the
autoneg bit is asserted.
This fixes any secondarily-issued networking commands on non-gigabit
links on the mpc8360 mds board.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Adds PCI support for MPC5121
Tested with drivers/net/rtl8139.c
Support is conditional since PCI on old silicon does not work.
ads5121_PCI_config turns on PCI
In this version, condition compilation of PCI code has been moved
from ifdef in board/ads5121/pci.c to board/ads5121/Makefile as
suggested by Jean-Christophe PLAGNIOL-VILLARD
Signed-off-by: John Rigby <jrigby@freescale.com>
U-Boot crashes in the net loop if CONFIG_4xx_DCACHE is
enabled. To reproduce the problem ensure that 'ethrotate'
environment variable isn't set to "no" and then run
"tftp 200000 not_existent_file".
This patch tries to fix the issue.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Currently (since commit b2e2142c) u-boot crashes on
sequoia board while SPR test if CONFIG_4xx_DCACHE is
enabled. This patch disables the cache while SPR test.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Call fdt_fixup_memory() on the boards TQM5200, TQM5200_B, TQM5200S,
TB5200 and TB5200_B to fixup the /memory node with the memory values
detected by U-Boot.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Call fdt_fixup_memory() on the boards TQM5200, TQM5200_B, TQM5200S,
TB5200 and TB5200_B to fixup the /memory node with the memory values
detected by U-Boot.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
This patch fixes a bug in the SDRAM initialization code for the
TQM5200. The hi_addr bit is now set correctly. Without this patch
the hi_addr bit is always set to 1, if the second SDRAM bank is
not populated.
For other MPC5200 boards a correspondig patch has already been applied
some time ago, see commit a63109281a.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
--
Forget the first patch please. I confused flash with SDRAM in
the comment ...
The previous patch was lacking of i386, microblaze, nios and nios2. This
patch tries to fix them.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
There is no reason to icbi when invalidating the temporary stack in
the d-cache. Its impossible on e500 to have the i-cache contain
any addresses in the temp stack and it can be problematic in generating
transactions on the bus to non-valid addresses.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The source vector for the ECM was being set to 2,
but that's what the source vector for DDR was being
set to. Change it to 1.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Commit 0db37dc... (and some others) changed the INIT_RAM TLB
mappings to be unguarded. This collided with an existing "bug"
where the mappings for the INIT_RAM were being kept around.
This meant that speculative loads to those addresses were
succeeding in the TLB, and going out to the bus, where they
were causing an exception (there's nothing at that address). The
Flash code was coincidentally causing such a speculative load.
Rather than go back to mapping the INIT RAM as guarded, we fix
it so that the entries for the INIT_RAM are invalidated. Thus
the speculative loads will fail in the TLB, and have no effect.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Back in commit a551cee99a
(86xx: Fix GUR PCI config registers properly), we should have
changed the MPC86xx_PORBMSR_HA and MPC86xx_PORDEVSR_IO_SEL
symbols in the sbc8641d board as well. Fix this oversight.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Don't include testdram() on NAND-booting target acadia_nand. This saves
a few bytes and makes the target build clean again.
Signed-off-by: Stefan Roese <sr@denx.de>
----------------------------------------------------------------
Olaf Hering [Wed, 17 Oct 2007 06:27:13 +0000 (23:27 -0700)]
Remove the __STRICT_ANSI__ check from the __u64/__s64 declaration on
32bit targets.
GCC can be made to warn about usage of long long types with ISO C90
(-ansi), but only with -pedantic. You can write this in a way that even
then it doesn't cause warnings, namely by:
#ifdef __GNUC__
__extension__ typedef __signed__ long long __s64;
__extension__ typedef unsigned long long __u64;
#endif
The __extension__ keyword in front of this switches off any pedantic
warnings for this expression.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
----------------------------------------------------------------
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
This reduces the build time by ~10%. Here's the gth2_config example.
BEFORE AFTER
real 0m31.441s 0m27.833s
user 0m24.766s 0m23.045s
sys 0m10.425s 0m7.468s
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
In the thread "[1.3.2-rc1] MPC8548CDS/MPC8555CDS configs fails to link",
the define2mk.sed script was identified as the source of the link
failure on FreeBSD. The problem is that sed(1) does not always support
the '+' operator. It isn't on FreeBSD. The attach patch implements the
equivalent, using the '*' operator instead and should work everywhere.
Signed-off-by: Marcel Moolenaar <marcelm@juniper.net>
The Linux commit fac8b209b1084bc85748bd54e13d00c1262b220f ("Remove
final traces of long-deprecated "ramdisk" kernel parm") makes these
changes neccessary.
Signed-off-by: Detlev Zundel <dzu@denx.de>
When the LM75 temperature sensor measures a temperature below 0 C, the
current driver does not perform sign extension, so the result returned is
256 C too high. This patch fixes the problem.
Signed-off-by: Larry Johnson <lrj@acm.org>
Some boards (e.g. lwmon5) may use rather small watchdog intervals, so
causing it to reboot the board if U-Boot does a long busy-wait with
udelay(). Thus, for these boards we have to restart WD more
frequently.
This patch splits the busy-wait udelay() into smaller, predefined,
intervals, so that the watchdog timer may be resetted with the
configurable (CONFIG_WD_PERIOD) interval.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Adds configuration option for ATI Radeon 9200 card
support to sequoia config file. If CONFIG_VIDEO
is enabled, TEXT_BASE should be changed to 0xFFF80000.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
For historical reasons we limited the stack to 256M because some boards
could only map that much via BATS. However newer boards are capable of
mapping more memory (for example 85xx is capable of doing up to 2G).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This bumps the autoconf.mk include step above board/cpu/arch/etc... so that
those .mk files can have make if statements based on the current config.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
If any of the steps for generating autoconf.mk fail currently, they go
unnoticed. To fix, we can simply add 'set -e' to the long list of commands.
This is simpler and more robust than placing '|| exit $$?' after every line.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
By adding VERSION_FILE to the PHONY targets the script
/tools/setlocalversion is always called and version_autogenerated.h
is replaced only if the script find a modified source file.
Signed-off-by: Stefano Babic <sbabic@denx.de>
- Fix flash_init call when CFG_NO_FLASH is used
- Remove no more needed flash.c for qemu-mips
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Michael Hennerich added support for outputting an image in RGB format rather
than forcing YUYV all the time. This makes obvious sense if the display you
have takes RGB input rather than YUYV.
Rather than hack in support for options, I've converted it to use getopt and
cleaned up the argument parsing in the process.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
If the $(LDSCRIPT) does not exist (normally it's board/$(BOARD)/u-boot.lds),
then change into the board directory and try and create it. This allows you
to generate the linker script on the fly based upon board defines (like the
Blackfin boards do).
There should be no regressions due to this change as the normal case is to
already have a u-boot.lds file. If that's the case, then there's nothing to
generate, and so make will always exit. The fix here is that if the linker
script does not exist, the implicit rules take over and attempt to guess how
to generate the file.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Do not use uninitialized cmd_reset; issue both AMD and Intel reset
commands instead
From a short test, it looks like AMD-style flash roms treat *any* unknown
command write as a reset, at least when in CFI Query mode, so issuing the
Intel reset command to AMD-style flashs seems safe (from the small sample I
have), plus the 3-cycle magic sequence should kick the state machine into
the right state even without a reset command. Since the AMD-style flashs
require the unlock sequence for real operation, I chose to try the AMD reset
command first, so that Intel flashs do no see an invalid command prior to
the CFI query.
I have tested the patch on AM29LV320-style flashs from Fujitsu and Macronix,
plus Intel StrataFlash.
Signed-off-by: Michael Schwingen <michael@schwingen.org>
Signed-off-by: Stefan Roese <sr@denx.de>
The CPU POST test code (run from cpu_post_exec_31()) doesn't follow the
ABI carefully, at least the CR3, CR4, and CR5 fields of CR are clobbered
by it. The gcc-4.2 with its more aggressive optimization exposes this fact.
This patch just saves the CR value before running the test code, so allowing
it to do anything it wants with CR.
Signed-off-by: Dmitry Rakhchev <rda@emcraft.com>
Acked-by: Yuri Tikhonov <yur@emcraft.com>
--
Back in commit 975a083a5e where
I tried to "8610HPCD: Fix typos in two PCI setup registers", I
botched it due to not realizing that 8610 and 8641 had different
Global Utility Register defintions, one of which was like 85xx,
and the other wasn't. Correct this problem by introducing two
symbols, one for each 86xx SoC, but neither of which is named
anything like 85xx.
My bad. Lovely Wednesday with git bisect. You know.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Without an actual supported video card hooked up, enabling
the CONFIG_VIDEO by default just makes it look broken by
routing all console output to the video card. Don't.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
The two symbols MPC86xx_PORDEVSR_IO_SEL and MPC86xx_PORBMSR_HA
were erroneously present as 85xx names and values, leftover from
the clone wars. Fix this by removing the 85xx cruft from the
86xx codebase.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
This is the proper fix for a missing closing brace in the function
ft_cpu_setup() noticed by joe.hamman <at> embeddedspecialties.com.
The ft_cpu_setup() function in mpc8641hpcn.c should have been
removed earlier as it was under the obsolete CONFIG_OF_FLAT_TREE,
but was missed. Only, the sbc8641d was nominally still using it.
It all got ripped out, and the funcality that was in ft_board_setup()
was refactored to remove the CPU portions into the new file
cpu/mpc86xx/fdt.c instead. Make sbc8641d use this now.
Based loosely on an original patch from joe.hamman@embeddedspecialties.com
Signed-off-by: Jon Loeliger <jdl@freescale.com>
The option CONFIG_I2C_MULTI_BUS does not have any effect on Sequoia, the
PPC440EPx reference platform, because IIC1 is never enabled. Add Sequoia board
code to turn on IIC1 if CONFIG_I2C_MULTI_BUS is selected.
Signed-off-by: Mike Nuss <mike@terascala.com>
Cc: Stefan Roese <sr@denx.de>
This patch tries to get rid of some assembler warnings about
changed .got2 section type while compiling x86 bios emulator
code.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch extends PCI device id table of the
radeon driver so that the driver will also support
Radeon Mobility 9200 (M9+) based boards.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Constantly rebuilding the version header will force useless relinking, so we
simply need to compare the new header with the existing one before updating
it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Update global_data to define i2c1_clk and i2c2_clk to 85xx and 86xx.
Update the get_clocks() function in 85xx and 86xx to determine the I2C
clock frequency and store it in gd->i2c1_clk and gd->i2c2_clk.
Signed-off-by: Timur Tabi <timur@freescale.com>
R29 was an unlucky choice as with recent toolchains (gcc-4.2.x) gcc
will refuse to use load/store multiple insns; instead, it issues a
list of simple load/store instructions upon function entry and exit,
resulting in bigger code size, which in turn makes the build for a
few boards fail.
Use r2 instead.
Signed-off-by: Wolfgang Denk <wd@denx.de>
If the variable "machid" exists, let do_bootm_linux use that instead
of bd->bi_arch_number.
Signed-off-by: Uwe Kleine-Knig <Uwe.Kleine-Koenig@digi.com>
Current MII_DEBUG is confusing in two ways. One is useless define-then-
undef at the top of the file. The other is there is only one debug() in
this file, and that doesn't seem worthwhile to bother having MII_DEBUG.
While there are many useful printf()/puts() debug codes, but they are for
DEBUG, not for MII_DEBUG.
This patch tries to put them all together into MII_DEBUG and debug().
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
This patch enables the OneNAND boot within U-Boot.
Before this work, we used another OneNAND IPL called X-Loader based
on open source. With this work, we can build the oneboot.bin image
without other program.
The build sequence is simple.
First, it compiles the u-boot.bin
Second, it compiles OneNAND IPL
Finally, it becomes the oneboot.bin from OneNAND IPL and u-boot.bin
The mechanism is similar with NAND boot except it boots from itself.
Another thing is that you can only use the OneNAND IPL only to work
other bootloader such as RedBoot and so on.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
A #if statement in fat.c depended on CONFIG_MMC, instead of
defined(CONFIG_MMC). This meant CONFIG_MMC needed to be defined
as "1" rather than just defined. Now it's better.
Signed-off-by: Andy Fleming <afleming@freescale.com>
---------------------------------
read_dataflash() takes a signed char pointer as a parameter. Silence a
few warnings dues to incorrect parameter types in env_dataflash.c.
Signed-off-by: Stelian Pop <stelian@popies.net>
Fix arm926ejs compile when SKIP_LOWLEVEL_INIT is on.
cpu/arm926ejs/start.o: In function `cpu_init_crit':
.../cpu/arm926ejs/start.S:227: undefined reference to `lowlevel_init'
Signed-off-by: Stelian Pop <stelian@popies.net>
Remove the "#undef DEBUG" line from all Freescale 83xx board header files.
The inclusion of this line makes it impossible to enable debug code in
other source files, because "#define DEBUG" typically needs to be defined
before any header files are included.
Signed-off-by: Timur Tabi <timur@freescale.com>
Move the flat device tree setup for QE related devices into
a common file shared between 83xx & 85xx platforms that have QE's.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Changes to match 5121 device tree going mainline in 2.6.25.
Change OF_SOC from "soc5121" to plain "soc".
Remove unneeded "ref-frequency" fixups.
Remove "address" enetaddr fixup.
Add bus-frequency fixup for old OF_SOC so old
kernels with old device trees will work with new
u-boot with 66MHz IPS clock
Signed-off-by: John Rigby <jrigby@freescale.com>
Move the flat device tree setup for QE related devices into
a common file shared between 83xx & 85xx platforms that have QE's.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The existing code assumes the SDRAM row refresh period should always
be 15.6 us. This is not always true, and indeed on the ATNGW100, the
refresh rate should really be 7.81 us.
Add a refresh_period member to struct sdram_info and initialize it
properly for both ATSTK1000 and ATNGW100. Out-of-tree boards will
panic() until the refresh_period member is updated properly.
Big thanks to Gerhard Berghofer for pointing out this issue.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The (now obsolete) atngw100 flash programming code was having problems
programming the onboard at49bv642 chip. The atstk1000 flash
programming code may have the same bug, so import fix for this problem
from the AVR32 Linux BSP.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The default load address is SDRAM + 2MB, not SDRAM + 4MB. The latter
wouldn't have worked anyway since the board can only access 4MB of
SDRAM.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Many people run into problems when they compile a big kernel and load
the uImage at the default SDRAM + 2MB address as the kernel will
overwrite the uImage as it is being unpacked. Increase the default
load address so that we can load a 4MB kernel image without any
problems.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
allow to use a different server as set in serverip
add CONFIG_TFTP_FILE_NAME_MAX_LEN to configure the file name length
if not defined the max length will be at 128
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Update global_data to define i2c1_clk and i2c2_clk to 85xx and 86xx.
Update the get_clocks() function in 85xx and 86xx to determine the I2C
clock frequency and store it in gd->i2c1_clk and gd->i2c2_clk.
Signed-off-by: Timur Tabi <timur@freescale.com>
According to the OMAP5912 Serial Interfaces Reference Guide (see
http://focus.ti.com/lit/ug/spru760c/spru760c.pdf, page 150), the
FIFO_EN enable bit in the FIFO Control Register (FCR) can only be
changed when the baud clock is not running, i. e. when both DLL and
DLH are set to 0.
Thus make sure that DLL and DLH are 0 when writing the FCR.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch allows us to use the 'gd' pointer (and thus environment
and everything else associated with it) from interrupt context on
arm920t.
Signed-off-by: Harald Welte <laforge@openmoko.org>
This patch adds a IRQ demultiplexer callback to the arm920 cpu core code,
plus a stub implementation of it for the S3C2410.
The purpose is to allow arm920t implementations such as the s3c24x0 to
implement interrupt handlers in u-boot without having to touch core
arm920t code.
Signed-off-by: Harald Welte <laforge@openmoko.org>
Add ifdef to bdinfo command to display ethernet information
only if CONFIG_CMD_NET is defined for arm modules.
Signed-off-by: K R Gururaja Hebbar <gururajakr@sanyo.co.in>
Adds I2C init func call to init sequence for ARM boards. This is
present in ppc,blackfin and other processor init sequence.
Signed-off-by: K R Gururaja Hebbar <gururajakr@sanyo.co.in>
The current ndfc HW ECC implementation swaps the first two ECC bytes.
But the 4xx NDFC already uses the SMC (Smart Media Card) ECC ordering,
so this swapping in the HW ECC driver is bogus. This patch fixes this
problem and now really uses the SMC ECC byte order.
Thanks to Sean MacLennan for pointing this out.
Signed-off-by: Stefan Roese <sr@denx.de>
The SRD0_PFC0 register was not configured correctly to enable the GPIO's
49-63 for GPIO. They have been configured as trace signals. This patch
fixes this by clearing the corresponding bit.
Signed-off-by: Stefan Roese <sr@denx.de>
Somewhere during development of U-Boot-1.1.3 CONFIG_BOOTBINFUNC was
renamed into CONFIG_INIT_CRITICAL which was 04 Apr 2005 replaced
with CONFIG_SKIP_LOWLEVEL_INIT and CONFIG_SKIP_RELOCATE_UBOOT.
However CONFIG_SKIP_LOWLEVEL_INIT has oposite meaning to
CONFIG_BOOTBINFUNC, so fix configuration to reflect this fact.
I'm sending this patch 4th (!) time in hope it produces at least some
reaction.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Fix at91rm9200dk base and environment address.
MMC support for X_Scale PXA is broken and does not work.
Mainly, the mmc_init() function cannot recognize current SD/MMC cards.
There were already some patches around the world but none of them was
merged into the official u-boot tree.
This patch makes order fixing this issue. Resubmit after code cleanup.
Applied and tested on PXA 270 (TrizepsIV module).
Signed-off-by: Stefano Babic <sbabic@denx.de>
Fix gcc4 issue. With some toolchain, a previous patch that fixes gcc4
issues generates wrong code.
(Problem was reported with gcc-4.0.2-glibc-2.3.6/arm-softfloat-linux-gnu).
This patch fixes the problem and solves the gcc-4 issues as the linux
kernel does.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Dmitry Ivanov <ivadmitry@gmail.com>
This fixes a build breakage with CONFIG_API enabled, which appeared after
the recent changes in the U-Boot build system.
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
Adds the support code in cpu/mpc86xx for the new law setup code
recently created fsl_law.c, and changes the MPC8641HPCN config
to use this code.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
* split the BAT initialization so that only 2 BATs (for the boot page
and stack) are programmed very early on. The rest are initialized later.
* Move other BAT setup, ccsrbar setup, and law setup later in the code
after translation has been enabled.
These changes will facilitate the moving of law and BAT initialization
to C code, and will aid with 36-bit physical addressing support.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
The commit 04a9e1180a
cause the 83xx immap broken, so the DMA and PCI will
be failed.
The patch fix the struct spi8xxx and rm struct spi83xx.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Add support for the ATNGW100 Network Gateway reference design,
including flash, ethernet and MMC support.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Hi,
The patch adds 4 boards, called AcTux-1 .. AcTux-4. This patch contains the
files that
contain changes for multiple boards, the board-specific files follow as
separate patches.
Signed-off-by: Michael Schwingen <michael@schwingen.org>
enables the RTS signal with CONFIG_SERIAL_RTS_ACTIVE.
No handshaking is done, but the active RTS signal allows to
connect to the target using a PC which is using RTS/CTS
handshake, and does no harm if the PC is set to ignore RTS.
Signed-off-by: Michael Schwingen <michael@schwingen.org>
allow to load the microde from flash or ram by download it through
the serial or other.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Stefan Roese <sr@denx.de>
Hi,
the following patch adds support to move the IXP42X NPE firmware to a
separate flash block, whose start address is defined in
CONFIG_IXP4XX_NPE_EXT_UCODE_BASE. Using that, it is possible to build
NPE-enabled u-boot without copyright problems due to the NPE firmware.
I hope the patch applies, I get whitespace-related differences in the NPE
files due to trailing whitespace in the original versions.
Signed-off-by: Michael Schwingen <michael@schwingen.org>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
- Fix EEPROM_data structure definition according to System EEPROM Data Format.
- Read MAC addresses from EEPROM to ethXaddr before saving ethXaddr to
bd->bi_ethaddr.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
This patch implements the fsl_spi driver on the MPC8349EMDS evaluation board.
This board has an ST M25P40 4Mbit EEPROM on its SPI bus
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds support for the SPI controller found on Freescale PowerPC
processors such as the MCP834x family. Additionally, a new config option,
CONFIG_HARD_SPI, is added for general purpose SPI controller use.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The commit 9e89647889
will cause the mpc8315erdb board can't boot up.
The patch fix that bug, and remove the duplicated #ifdef
CFG_SPCR_TSECEP code and clean the SCCR_TSEC2 for
MPC8313E processor.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
[PATCH] net: add 'ethrotate' environment variable
This patch replaces the buildtime configuration option
CONFIG_NET_DO_NOT_TRY_ANOTHER through the 'ethrotate' runtime
configuration veriable. See README.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
- Moved some common code to netstal/common/nm_bsp.c.
- sdram initialisation goes go netstal/common/fixed_sdram.c.
- Added support for POST.
- Stylistic cleanups (multi-line comments/ enforce 80 colomn width)
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
Added some routines used by all Netstal boards:
- nm_bsp.c: - nm_show_print and
- common_misc_init_r
- set_params_for_sw_install. Very specific code to handle our SW
installation procedure
- fixed_sdram.c: Common routines for HCU4 (and upcoming) MCU25 boards
to handle sdram initialization.
- nm.h: Common header
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
- Moved some common code to nestal/common/nm_bsp.c.
- Added support for the vxWorks EDR.
- Enable trace for Lauterbach, if present.
- Added support for POST.
- Stylistic cleanups (multi-line comments/ enforce 80 colomn width)
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
- Various fixes
- Reduced rom_size from 384 to 320 kB
- Environment is now in flash
- Added POST
- Support for OF
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
- Various fixes
- Reduced rom_size from 384 to 320 kB
- Environment is now in flash
- Added POST
- Support for OF
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
This patch fixed wrong SH7720 CPU macro and changed macro that
calculated value of SCBRR register.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Previous setting cause ips clock to be out of spec. This bug was found by John
Rigby from Freescale.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Now that all boards have been converted, remove old config code and the
config option for the new style.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Reworked the initial processor initialzation sequence:
* introduced cpu_early_init_f that is run in address space 1 (AS=1)
* Moved TLB/LAW and CCSR init into cpu_early_init_f()
* Reworked initial asm code to do most of the core init before TLBs
The main reasons for these changes are to allow handling of 36-bit phys
addresses in the future and some of the issues that will exist when we
do that.
There are a few caveats on what can be initialized via the LAW and TLB
static tables:
* TLB entry 14/15 can't be initialized via the TLB table
* any LAW that covers the implicit boot window (4G-8M to 4G) must map to
the code that is currently executing.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add a set of functions to manipulate TLB entries:
* set_tlb() - write a tlb entry
* invalidate_tlb() - invalidate a tlb array
* disable_tlb() - disable a variable size tlb entry
* init_tlbs() - setup initial tlbs based on static table
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We should be using the _MEM_PHYS for LAW and TLB setup and not _MEM_BASE.
While _MEM_BASE & _MEM_PHYS are normally the same, _MEM_BASE should only
be used for configuring the PCI ATMU.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move the initialization of the LAWs into C code and provide an API
to allow modification of LAWs after init.
Board code is responsible to provide a law_table and num_law_entries.
We should be able to use the same code on 86xx as well.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With serial, NE2000, IDE support. Tested in big-endian mode.
Memory size hard-coded to 128M for now, so don't play with
the -m option.
Signed-off-by: Vlad Lungu <vlad@comsys.ro>
rx_status on the memory is basically in LE, but needs to be handled in CPU
endian. le32_to_cpu() takes up this mission. Even if on the sane hardware,
it'll work fine.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Cc: Masami Komiya <mkomiya@sonare.it>
Cc: Lucas Jin <lucasjin@gmail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
"to = (currticks() + RTL_TIMEOUT)" has possibilities to wrap around. If it
does, the condition "(currticks() < to)" becomes invalid and immediately
leads to tx timeout error. This patch introduces the fine-graded udely(10)
loops to ease the impact of wrapping around.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Cc: Masami Komiya <mkomiya@sonare.it>
Cc: Lucas Jin <lucasjin@gmail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Add the support of RealTek RTL8211B PHY, the RTL8211B
PHY only supports RGMII and MII mode.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
PHY less board prints out lots of "read wrong ...":
read wrong value : mii_id 3,mii_reg 2, base e0102320
read wrong value : mii_id 3,mii_reg 3, base e0102320
UEC: PHY is Generic MII (ffffffff)
read wrong value : mii_id 3,mii_reg 4, base e0102320
read wrong value : mii_id 3,mii_reg 0, base e0102320
read wrong value : mii_id 3,mii_reg 1, base e0102320
read wrong value : mii_id 3,mii_reg 1, base e0102320
read wrong value : mii_id 3,mii_reg 5, base e0102320
read wrong value : mii_id 3,mii_reg 1, base e0102320
read wrong value : mii_id 3,mii_reg 1, base e0102320
read wrong value : mii_id 3,mii_reg 5, base e0102320
FSL UEC0: Full Duplex
FSL UEC0: Speed 100BT
FSL UEC0: Link is up
Using FSL UEC0 device
Make this printout depend on UEC_VERBOSE_DEBUG and
remove its definition in uec_phy.c
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
actually polling for PHY autonegotiation to finish enables us to remove the
5 second boot prompt latency present on QE based boards.
call to qe_set_mii_clk_src in init_phy, and mv call to init_phy from
uec_initialize to uec_init by Joakim Tjernlund; autonegotiation wait
code shamelessly stolen from tsec driver.
also rm unused CONFIG_RMII_MODE code.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The current TSEC driver limits MDIO access to the devices that have been configured as attached
to a TSEC MAC. This patch allows access to any PHY device on the MDIO bus through the 'mii' commands.
Signed-off-by: Michael Firth <michael.firth@bt.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
MPC837xERDB board support includes:
* DDR2 330MHz hardcoded (soldered on the board)
* Local Bus NOR Flash
* I2C, UART and RTC
* eTSEC RGMII (TSEC0 - RTL8211B with MII;
* TSEC1 - VSC7385 local bus, hardcoded, requires seperate firmware
* load)
Signed-off-by: Kevin Lam <kevin.lam@freescale.com>
Signed-off-by: Joe D'Abbraccio <joe.d'abbraccio@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
System registers that are modified are the Arbiter Configuration
Register (ACR), the System Priority Control Register (SPCR), and the
System Clock Configuration Register (SCCR).
Signed-off by: Michael F. Reiss <Michael.F.Reiss@freescale.com>
Signed-off by: Joe D'Abbraccio <ljd015@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Before, the order of arguments to the pixis_reset
command needed to be supplied in a hard-coded order.
Generalize the command parsing to allow any order.
Signed-off-by: James Yang <james.yang@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Convert the board/freescale/common/Makefile to use
CONFIG_* options to select which files to conditionally
compile into the board/freescale/common library rather
than conditionally compiling entire files.
Now handles::
CONFIG_FSL_PIXIS
CONFIG_FSL_DIU_FB
CONFIG_PQ_MDS_PIB
CONFIG_ID_EEPROM is introduced until CFG_ID_EEPROM is gone.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Use driver/net/uli526x.c as MPC8610HPCD default Ethernet driver.
Remove unused ethernet CONFIG_ options.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
mpc8360emds.c: In function 'ft_board_setup':
mpc8360emds.c:327: warning: assignment makes pointer from integer without a cast
mpc8360emds.c:329: warning: passing argument 2 of 'fdt_getprop' makes integer from pointer without a cast
mpc8360emds.c:334: warning: passing argument 2 of 'fdt_setprop' makes integer from pointer without a cast
mpc8360emds.c:341: warning: assignment makes pointer from integer without a cast
mpc8360emds.c:343: warning: passing argument 2 of 'fdt_getprop' makes integer from pointer without a cast
mpc8360emds.c:348: warning: passing argument 2 of 'fdt_setprop' makes integer from pointer without a cast
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
use tree passed to us in local blob, not global fdt.
Also use fdt_path_offset to convert to relative offset, since absolute
reference is needed to check for rgmii-id mode string value.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
These changes were identified by HighSmith Bill ,Mazzyar and Joseph for
DDR configuration in u-boot code. Some are related to performance, some
affect stability and some correct few basic errors in the current
configuration.
The changes have been tested and found to give better memory latency
figures on MPC8313eRDB.LMBench figures prove it.
The changes are:
- CS0_CONFIG[ AP_n_EN] is changed from 1 to 0
(this may improve performance for application with many read
or write to open pages).
- CS0_CONFIG[ODT_WR_CFG] is currently changed from 100 to
001 (activating all the CS when only one is used may cause
unwanted noise on the system)
- TIMING_CFG_1[ACTTOPRE] is changed from 9clks to 8clks (based on
Tras=45ns)
- TIMING_CFG_1[REFREC] changed from 21 clks to 18clks.
- TIMING_CFG_2[AL] value changed from 0 setting to 1 clk to
comply with the 3 ODT clk requirements)
- TIMING_CFG_2[CPO] was set to a reserved value, changed to RL+3/4.
- TIMING_CFG_2[FOUR_ACT] is changed from 10 clks to 6clks.
- DDR_SDRAM_MODE[AL]changed from 0 to 1.
- DDR_SDRAM_MODE[WRREC] changed from 1 clk to 3 clks.
- DDR_SDRAM_INTERVAL[REFINT] is changed from 0x0320 to 0x0510.
- DDR_SDRAM_INTERVAL[BSTOPRE] is changed from 0x64 to 0x0500.
The patch is based of git://www.denx.de/git/u-boot-mpc83xx.git
The last commit on this tree was 6775c68683
Signed-off-by: Poonam Aggrwal-b10812 <b10812@freescale.com>
Cc: Bill HighSmith <Bill.Highsmith@freescale.com>
Cc: Razzaz Mazyar <MRazzaz@freescale.com>
Cc: Josep P J <PJ.Joseph@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The isdram command prints out decoded information the "serial presence
detect" (SPD) chip on the SDRAM SIMMs. This can be very helpful when
debugging memory configuration problems.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The features list:
- Boot from NOR Flash
- DDR2 266MHz hardcoded configuration
- Local bus NOR Flash R/W operation
- I2C, UART, MII and RTC
- eTSEC0/1 support
- PCI host
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The TSEC emergency priority definition of 831x/837x
is different than the definition of 834x in SPCR register.
Add the other config of TSEC emergency priority into
cpu_init.c
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The MPC8360ERDK board support patch is added before
the commit 2c5b48fc20
so, miss clean up it.
The patch clean up the miss cache config.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The ECC POST reported intermittent failures running after power-up on
the Korat PPC440EPx board. Even when the test passed, the debugging
output occasionally reported additional unexpected ECC errors.
This refactoring has three main objectives: (1) minimize the code
executed with ECC enabled during the tests, (2) add more checking of the
results so any unexpected ECC errors would cause the test to fail, and
(3) use synchronization (only) where required by the processor.
Signed-off-by: Larry Johnson <lrj@acm.org>
This patch extends the number of supported UECs to 4. Note that the
problem of QE thread resources exhaustion is resolved by setting the
correct number of QE threads according to Ethernet type (GBE or FE).
Signed-off-by: David Saada <david.saada@ecitele.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
SH7710/SH7712 of SH3 CPU are supported.
SH771X is called SH-Ether, and has the Ether controller in CPU.
The driver of Ether is not included in this patch.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch add the support of map_physmem() and unmap_physmem()
used with Common Flash Interface(CFI) driver.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
post/cpu/ppc4xx/spr.c contained a few checks for registers only present
for PPC440 and derivates processor.
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
qe.c: In function 'qe_upload_firmware':
qe.c:390: warning: pointer targets in passing argument 2
uec.c: In function 'uec_initialize':
uec.c:1236: warning: 'uec_info' may be used uninitialized
Signed-off-by: Dave Liu <daveliu@freescale.com>
Now that bit 29 is the USB PHY reset bit, update the Kilauea port
to remove the USB PHY reset after powerup. The CPLD will keep the
USB PHY in reset (active low) until the bit is set to 1 in
board_early_init_f().
Signed-off-by: Stefan Roese <sr@denx.de>
- get rid of "version" target whichdidn't really work
- make autoconf.mk depend on version_autogenerated.h to make sure
to rebuild files as needed
- add XECHO macro to allow for silent build using "make -s"
Signed-off-by: Wolfgang Denk <wd@denx.de>
Currently, when CONFIG_CMDLINE_EDITING is set, bootretry doesn't work.
This patch fixes the problem.
Signed-off-by: Andreas Engel <andreas.engel@ericsson.com>
Many of the SPD bytes for DDR2 SDRAM are not interpreted correctly by the
"i2c sdram" command. This patch provides correct alternative
interpretations when DDR2 memory is detected.
Signed-off-by: Larry Johnson <lrj@acm.org>
With recent toolchain versions, some boards would not build because
or errors like this one (here for ocotea board when building with
ELDK 4.2 beta):
ppc_4xx-ld: section .bootpg [fffff000 -> fffff23b] overlaps section .bss [fffee900 -> fffff8ab]
For many boards, the .bss section is big enough that it wraps around
at the end of the address space (0xFFFFFFFF), so the problem will not
be visible unless you use a 64 bit tool chain for development. On
some boards however, changes to the code size (due to different
optimizations) we bail out with section overlaps like above.
The fix is to add the NOLOAD attribute to the .bss and .sbss
sections, telling the linker that .bss does not consume any space in
the image.
Signed-off-by: Wolfgang Denk <wd@denx.de>
There were some size and unsigned problems.
Also add support for "ll" size modifier in format string like glibc
Signed-off-by: James Yang <James.Yang@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
The TK885D board uses a TQM885D module from TQ, this port adds an
own configuration file and adds a last_stage_init() method to
configure the two PHYs, depending on the phy_auto_nego environment
variable.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Lines of the lenght CONSOLE_COLS or greater than CONSOLE_COLS
are not displayed correctly. This is an attempt to fix
this issue. Also add carriage return handling.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Clear possible errors in MCSR resulting from data-eye-search.
If not done, then we could get an interrupt later on when
exceptions are enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
According to the latest user manual of MPC8315E,
1) The SVCOD of HRCWL is different than 837x
2) The SCCR has changes
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This is MPC8360E based board with:
- 256MB fixed SDRAM;
- 8MB Intel Strata NOR flash;
- StMICRO 64MiB NAND flash;
- two 10/100/1000 ethernet ports connected via Broadcom
BCM5481 PHYs;
- two 10/100 ethernet ports connected via National
DP83848 PHYs;
- one PCI and one miniPCI slots;
- four serial ports (two NS16550-compatible, two UCCs);
- four USB ports working through MPC8360E "FHCI" USB controller;
- Fujitsu MB86277 graphics controller;
- Analog to Digital Converter/Touchscreen controller, AD7843
connected to SPI.
Features not supported in this patch are:
- StMICRO 64MiB NAND flash (patch sent);
- MINT framebuffer initialization (patch is pending);
- Fetching production information from the EEPROM via I2C;
- FHCI USB;
- Two slow UCCs used as RS-485 UARTs.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
the new libfdt code only updates eth0 if CONFIG_HAS_ETH0
is defined; add the define to the missing board configs.
Thanks to Emilian Medve for finding this.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Configure the number of bits used to address the banks inside the SDRAM
device. The default register value of 0 means 2 bits to address 4 banks.
Higher capacity devices like a 2GB DIMM require 3 bits to address 8 banks.
Signed-off-by: Becky Bruce <bgill@freescale.com>
vxWorks expects in
TLB 0 a entry for the Machine Check interrupt
TLB 1 a entry for the RAM
TLB 2 a entry for the EBC
TLB 3 a entry for the boot flash
After changing the baudrate to 9600 I had no problems to boot the
vxWorks image as distributed by WindRiver (Revision 2.0/1 from
June 18, 2007)
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
Change return values of init() functions in all Ethernet drivers to conform
to the following:
>=0: Success
<0: Failure
All drivers going forward should return 0 on success. Current drivers that
return 1 on success were left as-is to minimize changes.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-By: Timur Tabi <timur@freescale.com>
Define the layout of a binary blob that contains a QE firmware and instructions
on how to upload it. Add function qe_upload_firmware() to parse the blob and
perform the actual upload. Add command-line command "qe fw" to take a firmware
blob in memory and upload it. Update ft_cpu_setup() on 85xx to create the
'firmware' device tree node if U-Boot has uploaded a firmware. Fully define
'struct rsp' in immap_qe.h to include the actual RISC Special Registers.
Signed-off-by: Timur Tabi <timur@freescale.com>
Either use the standard defines in asm/cache.h or grab the information
at runtime from the L1CFG SPR.
Also, minor cleanup in cache.h to make the code a bit more readable.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In order to use GETH1 and GETH2 on the MPC8568E-MDS, we should reset
UCCs.
p.s Similar code exists in the Linux kernel board file (for capability
reasons with older U-Boots), but should be removed some day.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
The old macros made it difficult to know what WIMGE and perm bits
were set for a TLB entry. Actually use the bit masks for these items
since they are only a single bit.
Also moved the macros into mmu.h out of e500.h since they aren't specific
to e500.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Grab the FSL Book-E MAS register macros from Linux. Also added
defines for page sizes up to 4TB and removed SHAREN since it doesnt
really exist.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Way back in August I merged Heiko's patch:
566a494f59: [PCS440EP] upgrade the PCS440EP board
with Jon's CONFIG_COMMANDS patches.
This was done in commit: 6bf6f114dc
However, in the process, I left out some of Heiko's good changes.
Now Heiko's and Jon's patches are properly merged in fat_register_device()
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add new function readline_into_buffer() that allows the
output of readline to be put into a pointer to char buffer.
This refactoring allows other functions besides the
main command loop to also use the same input mechanism.
Signed-off-by: James Yang <James.Yang@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Ctrl combo key support is added, which is very useful to input Ctrl-C
for interrupt current job.
Also add usb_event_poll() calling to usb_kbd_testc(), which can get
key input when tstc() is called.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
We now have more useful version of do_mii() and everybody use it.
Gerald Van Baren says:
> When I originally wrote the mii command 6(!) years ago, I wrote a
> verbose version that printed human readable decomposition of the flags,
> etc., and a terse one that didn't print as much stuff and thus had a
> smaller memory footprint.
>
> It sounds like the terse version has withered and died, apparently
> people are only using the verbose version (which is very understandable,
> I do myself).
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
If type mii command without arguments, we suffer from uninitialized argv[]
entries; for example we MIPS get stuck by TLB error.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
This is an API for external (standalone) applications running on top of
U-Boot, and is meant to be more extensible and robust than the existing
jumptable mechanism. It is similar to UNIX syscall approach. See api/README
for more details.
Included is the demo application using this new framework (api_examples).
Please note this is still an experimental feature, and is turned off by
default.
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
Assumes the presence of the aliases node in the DTS to
locate the pci and serial nodes for fixups.
Use consistent fdtaddr and fdtfile in environment variables.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
didnt realize how out of shape easylogo actually was until i tried using it.
this patch does byte swapping as need be on the input tga header since the tga
is in little endian but the host could just as well be big endian. i didnt
bother using bswap macros or such stuff from system headers as nothing in
POSIX dictates byte swapping functionality.
Signed-Off-By: Mike Frysinger <vapier@gentoo.org>
- make the Makefile not suck
- include proper headers for prototypes
- fix obvious broken handling of strchr() when handling '.' in filenames
Signed-Off-By: Mike Frysinger <vapier@gentoo.org>
This patch allows u-boot to build without error in a cygwin
environment. Cygwin does not define __u64 in it's
include/asm/types.h file. The -idirafter flag in the u-boot
build causes the inclusion of the cygwin types.h file as opposed
to u-bot/include/asm/types.h file which does define __u64.
Subsequently, sha1.c compile fails due to unknown symbol.
Signed-off-by: Brian Miller <raptorbrino@netscape.net>
The existing code can show information about a gzip compressed BMP
image, but can't actually display it.
Therefore, move the decompression code out of bmp_info() and use it in
bmp_display() as well in order to display a compressed BMP image.
Also, clean things up a bit and fix a memory leak while we're at it.
[hskinnemoen@atmel.com: a bit of refactoring]
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch fixes several issues at least on a MPC885 based system with two
FEC interfaces used in MII mode.
1. PHY discovery should first read PHY_PHYIDR2 register and only then
PHY_PHYIDR1 like cpu/mpc8xx/fec.c::mii_discover_phy() does it,
otherwise the values read are wrong. Also notice, that PHY discovery
cannot work on MPC88x / MPC87x in setups with both FECs active at all
in its present form, because for both interfaces the registers from FEC
1 are used to communicate over MII.
2. Remove code duplication for resetting the FEC by isolating it into a
separate function.
3. Initialize MII on FEC 1 when communicating over FEC 2 in fec_init().
4. Optimize mii_init() to only reset the FEC 1 controller once.
5. Fix a typo in mii_init() using index i instead of j thus potentially
leading to unpredictable results.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
It is unclear on what platforms this driver has been tested, since
noone up to now defines CONFIG_RTL8169 in the board configuration
header. Now it has been fixed for a big-endian mpc8241 based
linkstation platform. This patch presents the necessary endianness
conversion fixes.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Ctrl combo key support is added, which is very useful to input Ctrl-C
for interrupt current job.
Also add usb_event_poll() calling to usb_kbd_testc(), which can get
key input when tstc() is called.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
This patch removes the unnecessary bit swapping when
booting .bit files with the 'fpga loadb' command.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
This patch adds a post configuration callback for Spartan2/3 FPGAs.
pre and post configuration callback are now optional and
not called when the function pointer is set to NULL.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
This patch removes the FPGA subsystem configuration through
the CONFIG_FPGA bitmask configuration option.
See README for the new options:
CONFIG_FPGA,
CONFIG_FPGA_<vendor>,
CONFIG_FPGA_<family>
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
With this patch it is possible to reimplement default_serial_console()
in board specific code. This will be done in the upcomming PMC440
U-Boot port. This also allows the lwmon board maintainer to
remove the '#if !defined(CONFIG_LWMON) ...' from common/serial.c.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
This patch adds a 'cu' like serial terminal command to u-boot
using which you can access other serial ports from the system console.
OpenMoko uses this in their Neo1973 phones to get access to the GSM
Modem and GPS chip from the bootloader.
Signed-off-by: Harald Welte <laforge@openmoko.org>
On LWMON5 we now use d-cache as init-ram and stack. The SPR POST test uses
self modifying code and this doesn't work with stack in d-cache, since
I can't move the code from d-cache to i-cache. We move the SPR test to
be executed a little later, after relocation. Then stack is located in
SDRAM and this self-modifying code is no problem anymore.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch configures the LWMON5 port to use d-cache as init-ram and
the unused GPT0_COMP6 as POST WORD storage.
Signed-off-by: Stefan Roese <sr@denx.de>
The privious 4xx POST implementation only supported storing the POST
WORD in OCM. Since we need to reserve the OCM on LWMON5 for the logbuffer
we need to store the POST WORD in some other non volatile location.
This patch adds CFG_POST_ALT_WORD_ADDR to specify an address for such
a location.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for locking the init-ram/stack in d-cache,
so that other regions may use d-cache as well
Note, that this current implementation locks exactly 4k of d-cache,
so please make sure that you don't define a bigger init-ram area. Take
a look at the lwmon5 440EPx implementation as a reference.
Signed-off-by: Stefan Roese <sr@denx.de>
ext2fs_read_file() had the function arguments swapped.
Pointed out by Mike Montour, 19 Dec 2007 22:34:25 -0800
Signed-off-by: Wolfgang Denk <wd@denx.de>
The MPC5200 OHCI controller operates in big endian, so
CFG_OHCI_BE_CONTROLLER must be defined for it to work properly.
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
This patch updates the fw_printenv/fw_setenv userspace tool to include
the correct MTD header in order to compile against current kernel
headers. Backward compatibility is preserved by introducing an option
MTD_VERSION which can be set to "old" for compilation using the old MTD
headers. Along with this a number of warnings are fixed.
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
This patch allows the use of 4xx interrupt vector number defines
in board specific code outside cpu/ppc4xx.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
This patch updates the PLB/PCI divider when running at
400MHz CPU frequency from 4 to 3 which results in 44MHz PCI sync clock.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Add CFG_NAND_QUIET_TEST option to disable error message when
no NAND chip is installed on PMC440 boards.
Disable a couple of config defines that are only used for NAND_U_BOOT.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
This patch updates the fw_printenv/fw_setenv userspace tool to include
the correct MTD header in order to compile against current kernel
headers. Backward compatibility is preserved by introducing an option
MTD_VERSION which can be set to "old" for compilation using the old MTD
headers. Along with this a number of warnings are fixed.
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
This is partial patch from the DTC/libfdt
commit 67b6b33b9b413a450a72135b5dc59c0a1e33e647
Author: David Gibson <david@gibson.dropbear.id.au>
Date: Wed Nov 21 11:56:14 2007 +1100
The patch also fixes one genuine bug caught by valgrind -
_packblocks() in fdt_rw.c was using memcpy() where it should have been
using memmove().
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
This patch adds more documenting comments to libfdt.h. Specifically,
these document the read/write functions (not including fdt_open_into()
and fdt_pack(), for now).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This patch adds some more documenting comments to libfdt.h.
Specifically this documents all the write-in-place functions.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Implement a suggestion by Scott Wood to make the /chosen handling fine
grained. Don't overwrite pre-existing properties on a per-property basis,
so if /chosen exists but a necessary /chosen/property doesn't, it gets
created. If a /chosen property exists, it is NOT overwritten unless the
"force" flag is true.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Add a note that "fdt copy" makes the new address active.
Remove most of the extra hints at the end of the fdt help.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Fix a bug found and documented by Bartlomiej Sieka where the optional
value on "fdt set <path> <prop> [<val>]" wasn't optional.
=> fdt mknode / testnode
=> fdt print /testnode
testnode {
};
=> fdt set /testnode testprop
=> fdt print /testnode
testnode {
testprop;
};
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
fdt_find_and_setprop() is used by several 4xx boards and it's
missing in the appropriate header. This patch eliminates a
warning when building U-Boot for such boards.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Acked-by: Stefan Roese <sr@denx.de>
convert to using simpler mpc85xx style fdt update code; streamline by
eliminating macros OF_SOC, OF_CPU, etc. which allows us to rm
the old school FLAT_TREE code from 83xx (since the sbc8349 was just
converted over to using libfdt).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Make libfdt the default for the WRS SBC8349 board.
Parallel of commit 35cc4e4823
done for the other 83xx based boards. Also fix a typo in CONFIG_PCI.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This adds libfdt support code for the Wind River sbc8349 board.
Parallel of commit 3fde9e8b22 for
the other Freescale 83xx boards.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
ECC code is now shared for all 83xx boards, so remove board specific one.
See commit daab8c67d2 for reference.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The MPC8360E MDS config defined:
CONFIG_OF_HAS_BD_T
CONFIG_OF_HAS_UBOOT_ENV
Which we don't use or ever needed. This seems like copy-paste feature creep.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
mpc8360emds.c: In function ‘ft_board_setup’:
mpc8360emds.c:335: warning: assignment discards qualifiers from pointer target type
mpc8360emds.c:345: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Fix the definitions of CFG_ENV_ADDR and CFG_ENV_SECT_SIZE for 837x.
This change guarantees that the environment will be located on the
first flash sector after the U-Boot image.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
u-boot itself uses GMII mode on the 8360. Fix up UCC phy-connection-type
properties in the device tree so the PHY gets configured for internal delay on
RX only by the OS, as prescribed by mpc8360 rev. 2.1 pb mds erratum #2.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The MPC837xEMDS board support:
* DDR2 400MHz hardcoded and SPD init
* Local bus NOR Flash
* I2C, UART, MII and RTC
* eTSEC RGMII
* PCI host
Signed-off-by: Dave Liu <daveliu@freescale.com>
The MPC8315E SoC including e300c3 core and new IP blocks,
such as TDM, PCI Express and SATA controller.
Signed-off-by: Dave Liu <daveliu@freescale.com>
The MPC837x SoC including e300c4 core and new IP blocks,
such as SDHC, PCI Express and SATA controller.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Despite user manual, BCSR9.7 is negated (high) on HRST, so
UART2 is disabled. Fix that and configure QE pins properly.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Fix the definitions of CFG_ENV_ADDR and CFG_ENV_SECT_SIZE for all of the
currently-defined 83xx boards. This change guarantees that the environment
will be located on the first flash sector after the U-Boot image.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Now that there are no board-specific versions of
"denali_core_search_data_eye()", the weak binding on the common version
can be removed.
Signed-off-by: Larry Johnson <lrj@acm.org>
On Katmai the complete auto-calibration somehow doesn't seem to
produce the best results, meaning optimal values for RQFD/RFFD.
This was discovered by GDA using a high bandwidth scope,
analyzing the DDR2 signals. GDA provided a fixed value for RQFD,
so now on Katmai "only" RFFD is auto-calibrated.
This patch also adds RDCC calibration as mentioned on page 7 of
the AMCC PowerPC440SP/SPe DDR2 application note:
"DDR1/DDR2 Initialization Sequence and Dynamic Tuning"
Signed-off-by: Stefan Roese <sr@denx.de>
Note: this patch changes the configuration of some GPIO registers:
Register Old Value New Value
--------------- ---------- ----------
DCR GPIO0_TCR 0x0000000F 0x0000F0CF
DCR GPIO0_TSRH 0x55005000 0x00000000
DCR GPIO1_TCR 0xC2000000 0xE2000000
DCR GPIO1_TSRL 0x0C000000 0x00200000
DCR GPIO1_ISR2L 0x00050000 0x00110000
Signed-off-by: Larry Johnson <lrj@acm.org>
This patch makes two additions to GPIO support:
First, it adds function gpio_read_in_bit() to read the a bit from the
GPIO Input Register (GPIOx_IR) in the same way that function
gpio_read_out_bit() reads a bit from the GPIO Output Register
(GPIOx_OR).
Second, it modifies function gpio_set_chip_configuration() to provide
an additional option for configuring the GPIO from the
"CFG_4xx_GPIO_TABLE".
According to the 440EPx User's Manual, when an alternate output is used,
the three-state control is configured in one of two ways, depending on
the particular output. The first option is to select the corresponding
alternate three-state control in the GPIOx_TRSH/L registers. The second
option is to select the GPIO Three-State Control Register (GPIOx_TCR) in
the GPIOx_TRSH/L registers, and set the corresponding bit in the
GPIOx_TCR register to enable the output. For example, the Manual
specifies configuring the GPIO00 Alternate 1 Signal (PreAddr07) to use
the alternate three-state control (first option), and specifies
configuring the GPIO32 Alternate 1 Signal (USB2OM0) with the output
enabled in the GPIOx_TCR register (second option).
Currently, gpio_set_chip_configuration() configures all alternate signal
outputs to use the first option. This patch allow the second option to
be selected by setting the "out_val" element in the table entry to
"GPIO_OUT_1". The first option is used when the "out_val" element is
set to "GPIO_OUT_0". Because "out_val" is not currently used when an
alternate signal is selected, and because all current GPIO tables set
"out_val" to "GPIO_OUT_0" for all alternate signals, this patch should
not change any existing configurations.
Signed-off-by: Larry Johnson <lrj@acm.org>
This patch also modifies the functionality of the code so that the data-eye
search is now done with with the cache disabled.
Signed-off-by: Larry Johnson <lrj@acm.org>
When CONFIG_NET_DO_NOT_TRY_ANOTHER is defined U-Boot's
networking stack does not automatically switch to
another interface. This patch does not touch the default
behavior.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch modifies the return code handling in the eth_init()
function, to be compatible with the handling of the return codes in
the other network stack files. It now returns a 0 on Success and -1 on
error.
Signed-off-by: Upakul Barkakaty <upakul.barkakaty@conexant.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Assigning the output of simple_strtoul(CB:A9:87:65:43:21) to `char', we are
warned as below:
U-Boot 1.2.0 (Aug 30 2007 - 08:27:37)
DRAM: 256 MB
Flash: 32 MB
In: serial
Out: serial
Err: serial
Net: NEC-Candy
Warning: NEC-Candy MAC addresses don't match:
Address in SROM is 00:00:4C:80:92:A2
Address in environment is FFFFFFCB:FFFFFFA9:FFFFFF87:65:43:21
This patch changes env_enetaddr type from `char' to `unsigned char'.
Cc: Masaki Ishikawa <ishikawa-masaki@cnt.mxe.nes.nec.co.jp>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The purpose of this routine is receiving a single network frame, outside of
U-Boot's NetLoop(). Exporting it to standalone programs that run on top of
U-Boot will let them utilise networking facilities. For sending a raw frame
the already existing eth_send() can be used.
The direct consumer of this routine is the newly introduced API layer for
external applications (enabled with CONFIG_API).
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Include config.h earlier in the set of #includes
so as to avoid a incidental and duplicate definition
of CFG_CACHELINE_SIZE.
Signed-off-by: Jon Loeliger
Assumes the presence of the aliases node in the DTS to
locate the ethernet, pci and serial nodes for fixups.
Use consistent fdtaddr and fdtfile in environment variables.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
This bug was detected on the LWMON5 target which has 2 Intel 16bit wide
flash chips connected to a 32bit wide port.
Signed-off-by: Stefan Roese <sr@denx.de>
The bash builtin versions of the "test" (resp. "[") command allow
using "==" for string comparisons, but POSIX compatible implemen-
tations (like /usr/bin/test) insist on using "=" only. On such systems
you will see:
$ /usr/bin/test a == a && echo OK
/usr/bin/test: ==: binary operator expected
This patch fixes Makefiles and scripts to use POSIX style.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This bug was detected on the LWMON5 target which has 2 Intel 16bit wide
flash chips connected to a 32bit wide port.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch brings the PMC440 board configuration file.
Finally it enables the PMC440 board support.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
This patch adds the first files for the new esd PMC440 boards.
The next two patches will complete the PMC440 board support.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
This patch fixes esd's LCD dectection code to work correctly with
newer gcc versions.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
In an attmemt to clean up the 4xx start.S file, I removed the enabling
of the internal 405EP PCI arbiter. This is needed for multiple other
405EP platforms, like most of the esd 405EP. Now the internal PCI
arbiter is enabled again per default as it has been before.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
This board never left prototyping state and it
became a millstone round my neck. So remove it.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
These patches add support for the PPC440EPx-based "Korat" board to
U-Boot. They are based primarily on support for the Sequoia board.
Signed-off-by: Larry Johnson <lrj@acm.org>
This patch adds SPD DDR2 support for the 440EPx ("Denali") SDRAM
controller. It should also work on the 440GRx. It is based on the DDR2
SPD code for the 440EP/440EPx, but makes no provision for DDR1 support.
This code has been tested on prototype Korat boards with three Kingston
DIMMS: 512 MiB ECC (one rank), 512 MiB non-ECC (one rank) and 1 GiB ECC
(two ranks). The Korat board has a single DIMM socket, but support has
been provided (though not tested) for boards with two DIMM sockets.
Signed-off-by: Larry Johnson <lrj@acm.org>
This patch creates a non-board-specific file for performing the SDRAM
data-eye search. It also adds ECC error checking to the test of valid
data on readback when ECC is enabled.
Signed-off-by: Larry Johnson <lrj@acm.org>
This patch adds the Denali SDRAM controller definitions to "ppc440.h".
It also fixes two typos in the definitions, so the board-specific
"sdram.h" files containing these definitions are also fixed to avoid
compiler warnings.
Signed-off-by: Larry Johnson <lrj@acm.org>
This patch adds a new switch: "CONFIG_PHY_DYNAMIC_ANEG". When this symbol
is defined, the PHY will advertise it's capabilities for autonegotiation
based on the capabilities shown in the PHY's status registers, including
1000BASE-X. When "CONFIG_PHY_DYNAMIC_ANEG" is not defined, the PHY will
advertise hard-coded capabilities, as before.
Signed-off-by: Larry Johnson <lrj@acm.org>
This driver is based on the driver for the M41T11. In the intended
application, the RTC will be powered by a large capacitor, rather than a
battery. The driver therefore checks to see whether the RTC has lost
power. The chip's OUT bit is normally reset from its power-up state. If
the OUT bit is read as set, or if the date and time are not valid, then the
RTC is assumed to have lost power, and its date and time are reset to
1900-01-01 00:00:00.
Support for adjusting the speed of the clock to improve accuracy is
provided through an environment variable.
Signed-off-by: Larry Johnson <lrj@acm.org>
On Sequoia & LWMON5 the virtual address of the POST cache test is now
moved to a bigger address. This enables usage of more memory on those
boards.
Signed-off-by: Stefan Roese <sr@denx.de>
As repoted by Larry Johnson, running "diag run cache" caused a crash
in U-Boot. This problem was introduced by a patch that removed the
TLB entry for the cache test after the test has completed. Since this
TLB was only setup once, a 2nd attempt to run this cache test
failed with a crash. Now this TLB entry is created every time the
routine is called.
Signed-off-by: Stefan Roese <sr@denx.de>
Now the cpu node setup ("timebase-frequency" and "clock-frequency") is
without using the absolute path to the cpu node. This makes it possible
to use this U-Boot version with both versions of cpu-node naming
"cpu@0" and the former "PowerPC,440EPx@0".
Signed-off-by: Stefan Roese <sr@denx.de>
ppc4xx clear_bss() fails if BSS segment size is not
divisible by 4 without remainder. This patch provides
fix for this problem.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
When using dhcp/bootp the "netmask" environment variable is not
set because CONFIG_BOOTP_SUBNETMASK is not defined. But usually this is
desireable, so the following patch adds this this option to the board
config.
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch allows the ECC POST to be used for different boards with the
PPC440 Denali SDRAM controller. Modifications include skipping the test
if ECC is not enabled (as for non-ECC DIMMs) and adding synchronization
to prevent timing errors.
Signed-off-by: Larry Johnson <lrj@acm.org>
flush + invalidate_dcache_range() expect the start and stop+1 address.
So the stop address is the first address behind (!) the range.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
By using aliases in the dts file, the ethernet node fixup is
much easier with the recently added functions.
Please note that the dts file needs the aliases for this to work.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch update the 4xx fdt support. It enabled fdt booting
on the AMCC Kilauea and Sequoia for now. More can follow later
quite easily.
Signed-off-by: Stefan Roese <sr@denx.de>
The check for an sufficiently erased destination was missing in the
buffered write function of the cfi flash driver (when
CFG_FLASH_USE_BUFFER_WRITE is defined). This patch adds this check to that
writing to such a region will fail with the currect error message.
Signed-off-by: Stefan Roese <sr@denx.de>
CAS-Latency=2, Write Recovery Time tWR=2
The max. supported bus frequency is 66 MHz. Therefore, changed
threshold to switch from 1:1 mode to 2:1 from 80 MHz to 66 MHz.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
On the TQM885D the measurement of cpuclk with the PIT reference
timer ist not necessary. Since all module variants use the same
external 10 MHz oscillator, the cpuclk only depends on the PLL
configuration - which is readable by software.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
At 133 MHz the current SDRAM refresh rate is too fast
(measured 4 * 1.17 us).
CFG_MAMR_PTA changes from 39 to 128. This result
in a refresh rate of 4 * 7.8 us at the default clock
66 MHz. At 133 MHz the value will be then 4 * 3.8 us.
This is a compromise until a new method is found to
adjust the refresh rate.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Run fixups based on the JEDEC manufacturer ID independent of the
command set ID.
This changes current behaviour: Previously, geometry reversal for AMD
chips were done based on the command set ID, while they are now done
based on the JEDEC manufacturer and device ID.
Also add fixup for top-boot Atmel chips. A fixup is needed for
AT49BV6416(T) too, but since u-boot currently only reads the low byte
of the device ID, there's no way to tell it apart from AT49BV642D,
which should not have this fixup. Since AT49BV642D support is
necessary to get ATNGW100 board support into mainline, I've commented
out the fixup for now.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Move things like reading JEDEC IDs and fixing up geometry reversal
into separate functions. The geometry reversal fixup is now performed
by altering the qry structure directly, which makes the sector init
code slightly cleaner.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Read out the whole CFI Standard Query structure after successful cfi
identification. This allows subsequent code to access this information
directly without having to go through flash_read_uchar() and friends.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
disable_interrupts() should return nonzero if interrupts were
_enabled_ before, not disabled.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The timer code depends on the timer interrupt to keep track of the
upper 32 bits of the cycle counter. This obviously doesn't work when
interrupts are disabled the whole time.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
As reported by Gerhard Berghofer:
in "gpio_enable_usart3" the correct pins for USART 3 are PB17 and PB18
instead of PB18 and PB19.
which is obviously correct. There's currently no code that uses
USART3, but custom boards may run into problems.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Add all the ATSTK1000 daughterboards to MAINTAINERS along with their
"mother". Also update the entry for ATSTK1000 to be not only about the
AP7000 CPU; it's intended to handle all CPUs in the AT32AP family.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
ATSTK1004 is a daughterboard for ATSTK1000 with the AT32AP7002 CPU,
which is a derivative of AT32AP7000.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
ATSTK1003 is a daughterboard for ATSTK1000 with the AT32AP7001 CPU,
which is a derivative of AT32AP7000.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Add a chip-features file providing definitions of the form
AT32AP700x_CHIP_HAS_<peripheral>
to indicate the availability of the given peripheral on the currently
selected chip.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The SoC-specific code for all the AT32AP700x CPUs is practically
identical; the only difference is that some chips have less features
than others. By doing this rename, we can add support for the AP7000
derivatives simply by making some features conditional.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch update the 4xx fdt support. It enabled fdt booting
on the AMCC Kilauea and Sequoia for now. More can follow later
quite easily.
Signed-off-by: Stefan Roese <sr@denx.de>
Use map_physmem() and unmap_physmem() to convert from physical to
virtual addresses. This gives the arch a chance to provide an uncached
mapping for flash accesses.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
map_physmem() returns a virtual address which can be used to access a
given physical address without involving the cache. unmap_physmem()
should be called when the virtual address returned by map_physmem() is
no longer needed.
This patch adds a stub implementation which simply returns the
physical address cast to a uchar * for all architectures except AVR32,
which converts the physical address to an uncached virtual mapping.
unmap_physmem() is a no-op on all architectures, but if any
architecture needs to do such mappings through the TLB, this is the
hook where those TLB entries can be invalidated.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Introduce flash_read{8,16,32,64) and flash_write{8,16,32,64} and use
them to access the flash memory. This makes it clearer when the flash
is actually being accessed; merely dereferencing a volatile pointer
looks just like any other kind of access.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This adds implementations of __raw_read[bwl] and __raw_write[bwl] to
m68k, ppc, nios and nios2. The m68k and ppc implementations were taken
from Linux.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Reorder the functions in cfi_flash.c so that each function only uses
functions that have been defined before it. This allows the static
prototype declarations near the top to be eliminated and might allow
gcc to do a better job inlining functions.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch tries to keep all lines in the cfi_flash driver below 80
columns. There are a few lines left which don't fit this requirement
because I couldn't find any trivial way to break them (i.e. it would
take some restructuring, which I intend to do in a later patch.)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
On the MPC85xx boards that have PCIe enable the PCIe errata fix.
(MPC8544DS, MPC8548CDS, MPC8568MDS).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8572 introduces the concept of an asynchronous DDR clock with
regards to the platform clock.
Introduce get_ddr_freq() to report the DDR freq regardless of sync/async
mode.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We already had defines for LAWAR_TRGT_IF_* that we should use
rather than creating new ones. Also, added some missing defines for
PCIE targets.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In the future the offsets to various blocks may not be in same location.
Move to using CFG_MPC85xx_*_ADDR as the base of the registers
instead of getting it via &immap.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Updated the MPC8568 MDS config to use libfdt and assume use of aliases for
ethernet, pci, and serial for the various fixups that are done.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Updated the MPC85xx CDS config to use libfdt and assume use of aliases for
ethernet, pci, and serial for the various fixups that are done.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Updated the MPC8540 ADS config to use libfdt and assume use of aliases for
ethernet, pci, and serial for the various fixups that are done.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Updated the MPC8560 ADS config to use libfdt and assume use of aliases for
ethernet, pci, and serial for the various fixups that are done.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In the future the offsets to various blocks may not be in same location.
Move to using CFG_MPC85xx_CPM_ADDR as the base of the CPM registers
instead of getting it via &immap->im_cpm.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In the future the offsets to various blocks may not be in same location.
Move to using CFG_MPC85xx_GUTS_ADDR as the base of the guts registers
instead of getting it via &immap->im_gur.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Removed HAS_ETH2/HAS_ETH3 - MPC8544 only has TSEC1/2
* Removed some misc environment setup
* Moved to using fdtfile & fdtaddr as fdt env var names
* Enabled CONFIG_CMDLINE_EDITING
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Updated the MPC8544DS config to use libfdt and assume use of aliases for
ethernet, pci, and serial for the various fixups that are done.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch selects the USB data pins in the 405EX GPIO and MFC (multi
function control) registers. This is done for the AMCC Kilauea and
Makalu eval boards.
Signed-off-by: Stefan Roese <sr@denx.de>
The following patch adds support for non-CFI flash ROMS, by hooking into the
CFI flash code and using most of its code, as recently discussed here in the
thread "Mixing CFI and non-CFI flashs".
Signed-off-by: Michael Schwingen <michael@schwingen.org>
Signed-off-by: Stefan Roese <sr@denx.de>
We use a combination of the serialN alias and CONFIG_CONS_INDEX to
determine which serial alias we should set linux,stdout-path to.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The composition of the directory in the drivers/ changed.
I moved SuperH serial driver and marubun PCMCIA driver.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch enables the hardware-fix for the PCI/DMA errata's 19+22 by
setting the FIXD bit in the SDR0_MFR register. Here a description of the
symptoms:
Problem Description
------------------------------
If a DMA is performed between memory and PCI with the DMA 1 Controller
using prefetch, and as a result uses a special purpose buffer selected by
the PCIXn Bridge Options 1 Register (PCIXn_BRDGOPT1[RBP7] - bits 31-29),
the first part of the transfer sequence is performed twice. The
PPC440SPe PCI Controller requests more data than was needed such that in
the case of enforce memory protection, a host CPU exception can occur.
No data is corrupted, because data transfer is stopped in the PCI
Controller. Prefetch enable is specified by setting DMA Configuration
Register (I2O0_DMAx_CFG[DXEPD] - bit 31) to 0.
Behavior that may be observed in a running system
---------------------------------------------------------------------------
1. DMA performance is decreased because of the double access on the PCI bus
interface.
2. If an illegal access to some address on the PCI bus is detected at the
system level, a machine check or similar system error may occur.
Workarounds Available
----------------------------------
1. Do not program prefetch. Note that a prefetch command cannot be programmed
without selecting a special purpose buffer.
2. To avoid crossing a physical boundary of the PCI slave device, add 512
bytes of address to the PCI address range.
This patch was originally provided by Pravin M. Bathija <pbathija@amcc.com>
from AMCC and slighly changed.
Signed-off-by: Pravin M. Bathija <pbathija@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This manual PCIe reset triggering solves the problem seen with the
Intel EPRO/1000 card, which was not detected (link not established)
upon power-up reset.
Signed-off-by: Stefan Roese <sr@denx.de>
Marubun pcmcia is a chip for PCMCIA used with SuperH.
Of course, this can be used even by other architectures.
When use this driver, came to be able to use CompactFlash
and Ethernet.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
After an error in the AMCC 405EX users manual now correctly configure
IRQ2 (Kilauea)/IRQ0 (Makalu) as alternate 2 signal for external IRQ
usage.
Signed-off-by: Stefan Roese <sr@denx.de>
These two structures are still needed during the
initialization and setup of the DIU hardware.
So move them to the fsl_diu_fb.h file for now.
Official "blah".
Noticed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Till now the UTL registers on 405EX were not initialized but left with
their default values. This patch new initializes some of the UTL
registers on 405EX.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds changes needed for Makalu rev 1.1:
- Enable 2nd DDR2 bank resulting in 256MByte of SDRAM
- Enable 2nd ethernet port EMAC1
- Use generic GPIO configuration framework (CFG_4xx_GPIO_TABLE)
- Reset PCIe ports via GPIO upon bootup
Signed-off-by: Stefan Roese <sr@denx.de>
- Rename CFG_440_GPIO_TABLE to CFG_4xx_GPIO_TABLE
- Cleanup of the 4xx GPIO functions
- Move some GPIO defines from the cpu headers ppc405.h/ppc440.h into gpio.h
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for three new DDR chips that may be present on a NG
INKA4x0 hardware: HYB25D512160BF-5, K4H511638C-7CB3, T46V32M16BN-6IT.
Cleanup board/inka4x0/mt48lc16m16a2-75.h file.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
This patch makes the sequoia board use the generic usb-ohci driver
instead of cpu/ppc4xx/usb_ohci.c.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch disables the 44x d-cache on 'usb start' and
reenables it on 'usb stop'. This should be seen as a
temporary fix until the generic usb-ohci driver can
life with d-cache enabled.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes some redundant code and decrements the end
address of cache flush and invalidate by 1.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Most 4xx PPC capable of using an I2C bootrom for bootstrap setting
already print a line with the information which I2C bootrom is
used for bootstrap configuration. So we don't need this extra line
with "I2C boot EEPROM en-/dis-abled".
This patch also has a little code cleanup integrated.
Signed-off-by: Stefan Roese <sr@denx.de>
Add cfb console support to FSL 8610 DIU driver.
Inspect board version from PIXIS to obtain correct pixel format.
Use #define CONFIG_VIDEO in config file to enable fb console.
To switch monitor, set monitor variable to
0 - DVI, 1 - Single link LVDS, 2 - Double link LVDS
followed by "diufb init".
Preserve logo bitmap at the top of the fb console.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
1280x1024 and 1024x768 @ 32 bpp are supported now.
DVI, Single-link LVDS, Double-link LVDS are all supported.
Environmental variable "monitor" is used to specify monitor port.
A new command "diufb" is introduced to reinitialize monitor
and display a BMP file in the memory. So far, 1-bit, 4-bit,
8-bit and 24-bit BMP formats are supported.
diufb init
- initialize the diu driver
Enable the port specified in the environmental variable "monitor"
diufb addr
- display bmp file in memory.
The bmp image should be no bigger than the resolution, 1280x1024
for DVI and double-link LVDS, 1024x768 for single-link LVDS.
Note, this driver allocate memory but doesn't free it after use
It is written on purpose -- to avoid a failure of reallocation
due to memory fragement.
ECC of DDR is disabled for DIU performance. L2 data cache is also disabled.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Jon loeliger <jdl@freescale.com>
This Freescale logo is a 340 x 128 x 4bpp BMP file
that can be displayed by the DIU Framebuffer driver.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
The address in the BAT register is aligned with the BAT size.
The original definition actually did not define BAT for PCIE2 IO.
This patch fix this.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Basically, refactor the CFG_PIXIS_VBOOT_MASK values
into the separate board config files.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
This patch adds NAND booting support for the AMCC 405EX(r) eval boards.
Again, only one image supports both targets.
Signed-off-by: Stefan Roese <sr@denx.de>
Since the cache handling functions were moved from start.S into cache.S
the acadia NAND booting Makfile needs to be adapted accordingly.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the CONFIG_4xx_DCACHE options to some SDRAM init files
and to the Sequoia TLB init code. Now the cache can be enabled on 44x
boards by defining CONFIG_4xx_DCACHE in the board config file. This
option will disappear, when more boards use is successfully and no
more known problems exist.
This is tested successfully on Sequoia and Katmai. The only problem that
needs to be fixed is, that USB is not working on Sequoia right now, since
it will need some cache handling code too, similar to the 4xx EMAC driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Now with caches enabled (i- and d-cache) on 44x, we need a chance to
disable the cache for the CPU POST tests, since these tests consist
of self modifying code. This is done via the new change_tlb() function.
Signed-off-by: Stefan Roese <sr@denx.de>
I lately noticed, that newer 4xx board with GBit support sometimes don't
finish link autonegotiation in 4 seconds. Changing this timeout to 5
seconds seems fine here.
Signed-off-by: Stefan Roese <sr@denx.de>
The POST ethernet test needed to be changed to dynamically determine
the count of ethernet devices. This code is cloned from the 4xx
ethernet driver.
Signed-off-by: Stefan Roese <sr@denx.de>
We now use a value in the gd (global data) structure for the UART input
frequency, since the PPC4xx_SYS_INFO struct is always rewritten completely
in get_sys_info().
Signed-off-by: Stefan Roese <sr@denx.de>
The Haleakala is nearly identical with the Kilauea eval board. The only
difference is that the 405EXr only supports one EMAC and one PCIe
interface. This patch adds support for the Haleakala board by using
the identical image for Kilauea and Haleakala. The distinction is done
by comparing the PVR.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch also adds a note to the fixed DDR setup for Bamboo NAND booting:
Note:
As found out by Eugene O'Brien <eugene.obrien@advantechamt.com>, the fixed
DDR setup has problems (U-Boot crashes randomly upon TFTP), when the DIMM
modules are still plugged in. So it is recommended to remove the DIMM
modules while using the NAND booting code with the fixed SDRAM setup!
Signed-off-by: Eugene O'Brien <eugene.obrien@advantechamt.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Change 4xx_uart.c:
- Use in_8/out_8 macros instead of in8/out8
- No need for UART_BASE marco anymore, now really handled via function
parameter
- serial_init_common() introduced
- Further coding style cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
Change all linker scripts to reference the changed driver name 4xx_uart.o.
Note: In most cased all these explicit referencing of these object files
in the linker scripts is not neccessary. Only for manually embedded
environment into the U-Boot image, which is not done is most cases.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch starts the rework of the PPC4xx serial driver. First we split
the file into two seperate files, one 4xx_uart.c with the 405/440 UART
handling code and the other one iop480_uart.c with the UART code for the
PLX-Tech IOP480 PPC (PPC403 based).
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for the Xicor/Intersil X1205 RTC used on the
AMCC Makalu eval board. This driver is basically cloned from the Linux
driver version (2.6.23).
This patch also introduces the Linux bcd.h header for the BCD2BIN/
BIN2BCD conversions. In the future some of the other U-Boot RTC driver
should be converted to also use this header instead of implementing
their own local copy of these functions/macros.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch moves some common 4xx macros and the PPC405_SYS_INFO/
PPC440_SYS_INFO structure into the common ppc4xx.h header.
Lot's of other macros are good candidates to be consolidated this way
in the future.
Signed-off-by: Stefan Roese <sr@denx.de>
The size was initilized wrong. Instead of 256MB, the DDR2 controller
was setup to 512MB. Now the correct values is used.
This patch also does a little cleanup and adds a comment here.
Signed-off-by: Stefan Roese <sr@denx.de>
CONFIG_BOOKE must be defined for PPC440 processors so that the proper SPR
number is used to access system registers.
Signed-off-by: Eugene O'Brien <eugene.obrien@advantechamt.com>
Signed-off-by: Stefan Roese <sr@denx.de>
On Yucca & Katmai, the inbound memory map pointed to 0x4.0000.0000, which
is the internal SRAM. Since I now ported and tested this endpoint mode
on Kilauea successfully to map to 0 (SDRAM), I also changed this for
Katmai.
Yucca will stay at internal SRAM for now. Not sure if somebody relies on
this setup.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds endpoint support for the AMCC Kilauea eval board. It can
be tested by connecting a reworked PCIe cable (only 1x lane singles
connected) to another root-complex.
In this test setup, a 64MB inbound window is configured at BAR0 which maps
to 0 on the PLB side. So accessing this BAR0 from the root-complex will
access the first 64MB of the SDRAM on the PPC side.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for dynamic configuration of PCIe ports for the
AMCC PPC4xx boards equipped with PCIe interfaces. These are the PPC440SPe
boards Yucca & Katmai and the 405EX board Kilauea.
This dynamic configuration is done via the "pcie_mode" environement
variable. This variable can be set to "EP" or "RP" for endpoint or
rootpoint mode. Multiple values can be joined via the ":" delimiter.
Here an example:
pcie_mode=RP:EP:EP
This way, PCIe port 0 will be configured as rootpoint, PCIe port 1 and 2
as endpoint.
Per default Yucca will be configured as:
pcie_mode=RP:EP:EP
Per default Katmai will be configured as:
pcie_mode=RP:RP:REP
Per default Kilauea will be configured as:
pcie_mode=RP:RP
Signed-off-by: Tirumala R Marri <tmarri@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables the fdt support on the AMCC Kilauea eval board.
Additionally now EBC ranges fdt fixup is included to support NOR
FLASH mapping via the Linux physmap_of driver.
This Kilauea port now support booting arch/ppc and arch/powerpc
Linux kernels. The default environment "net_nfs" is for arch/ppc
and "net_nfs_fdt" is for arch/powerpc. In the long run, arch/ppc
support will be removed.
Signed-off-by: Stefan Roese <sr@denx.de>
128MB seems to be the smallest possible value for the memory size
for on PCIe port. With this change now the BAR's of the PCIe cards
are accessible under U-Boot.
One big note: This only works for PCIe port 0 & 1. For port 2 this
currently doesn't work, since the base address is now 0xc0000000
(0xb0000000 + 2 * 0x08000000), and this is already occupied by
CFG_PCIE0_CFGBASE. But solving this issue for port 2 would mean
to change the base addresses completely and this change would have
too much impact right now.
This patch adds debug output to the 4xx pcie driver too.
Signed-off-by: Stefan Roese <sr@denx.de>
These files were introduced with the IBM 405GP but are currently used on all
4xx PPC platforms. So the name doesn't match the content anymore. This patch
renames the files to 4xx_pci.c/h.
Signed-off-by: Stefan Roese <sr@denx.de>
(3) This patch introduces macros like SDRN_PESDR_DLPSET(port) to access
the SDR registers of the PCIe ports. This makes the overall design
clearer, since it removed a lot of switch statements which are not
needed anymore.
Also, the functions ppc4xx_init_pcie_rootport() and
ppc4xx_init_pcie_entport() are merged into a single function
ppc4xx_init_pcie_port(), since most of the code was duplicated.
This makes maintainance and porting to other 4xx platforms
easier.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch is the first patch of a series to make the 440SPe PCIe code
usable on different 4xx PPC platforms. In preperation for the new 405EX
which is also equipped with PCIe interfaces.
(2) This patch renames the functions from 440spe_ to 4xx_ with a
little additional cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
This patch is the first patch of a series to make the 440SPe PCIe code
usable on different 4xx PPC platforms. In preperation for the new 405EX
which is also equipped with PCIe interfaces.
(1) This patch renames the files from 440spe_pcie to 4xx_pcie
Signed-off-by: Stefan Roese <sr@denx.de>
usb_cpu_init() configures GPS USB pins, clocks, etc. and
is required for proper operation of kernel USB subsystem.
This setup was previously done in the kernel by the fixup
code which is being removed, thus low level init must be
done by U-boot now.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
The scan code of the key 'z' is 0x1d, which should be handled.
The change has be tested on NOVATEK USB keyboard and ULI PCI OHCI
controller.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
Some USB keys need to be switched off before loading the kernel
otherwise they can remain in an undefined status which prevents them
to be correctly recognized by the kernel.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
printf("===== Display reset and initialize register Start =========\n");
mfclk(clk_pllc,reg);
mfcpr(clk_pllc,reg);
printf("cpr_pllc = %#010x\n",reg);
mfclk(clk_plld,reg);
mfcpr(clk_plld,reg);
printf("cpr_plld = %#010x\n",reg);
mfclk(clk_primad,reg);
mfcpr(clk_primad,reg);
printf("cpr_primad = %#010x\n",reg);
mfclk(clk_primbd,reg);
mfcpr(clk_primbd,reg);
printf("cpr_primbd = %#010x\n",reg);
mfclk(clk_opbd,reg);
mfcpr(clk_opbd,reg);
printf("cpr_opbd = %#010x\n",reg);
mfclk(clk_perd,reg);
mfcpr(clk_perd,reg);
printf("cpr_perd = %#010x\n",reg);
mfclk(clk_mald,reg);
mfcpr(clk_mald,reg);
printf("cpr_mald = %#010x\n",reg);
/* read sdr register */
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
