Microblaze uses gpio which is connected to the system reset.
Currently gpio subsystem wasn't used for it.
Add gpio driver and change Microblaze reset logic to be done
via gpio subsystem.
There are various configurations which Microblaze can have
that's why gpio_alloc/gpio_alloc_dual(for dual channel)
function has been introduced and gpio can be allocated
dynamically.
Adding several gpios IP is also possible and supported.
For listing gpio configuration please use "gpio status" command
This patch also remove one compilation warning:
microblaze-generic.c: In function 'do_reset':
microblaze-generic.c:38:47: warning: operation on '*1073741824u'
may be undefined [-Wsequence-point]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Watchdog can be used on Microblaze, PPC and Zynq hw designs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Fix microblaze soft reset function and disable
all cpu features. Especially disable caches because
IRQs were off by disable_interrupts().
Reported-by: John Williams <john.williams@xilinx.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove CONFIG_SYS_RESET_ADDRESS macro.
It was there from historical point of view
when soft reset was just jump to u-boot text start
(not used right now).
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This code was targetting one specific Microblaze platform
configuration which is obsolete and fsl bus isn't used
in this way.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
All these files was used for ancient xilinx drivers
which are finally gone.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Rommel Custodio <sessyargc@gmail.com>
There is new driver in the driver folder.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Rommel Custodio <sessyargc@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
Add support for Xilinx Zynq board.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Marek Vasut <marex@denx.de>
CC: Joe Hershberger <joe.hershberger@gmail.com>
Move board specific function to board_init function in board/ folder
Remove externs from generic board.c
Use board_init_f function in board.c file.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Stephan Linz <linz@li-pro.net>
- enable OF control and embedded OF
- set default device tree file name to 'microblaze'
- add CPP to dtc proxy: board/xilinx/dts/microblaze.dts
- add an empty but processable dts for microblaze-generic
Signed-off-by: Stephan Linz <linz@li-pro.net>
Expand the specific configuration for the microblaze-generic
board in xparameters.h with a faked setup to enable the
LL_TEMAC driver.
Note: From now the microblaze-generic board is no longer a
valid board configuration for a real piece of hardware. Rather
than, we use the file config.mk and xparameters.h as a faked
board configuration to force the compilation of all potential
driver code for Microblaze systems.
Signed-off-by: Stephan Linz <linz@li-pro.net>
This driver doesn't support the NET_MULTI framework, and I can't find
any boards/configs/files that reference this subdir, so punt it all.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The top level Makefile does not do any recursion into subdirs when
cleaning, so these clean/distclean targets in random arch/board dirs
never get used. Punt them all.
MAKEALL didn't report any errors related to this that I could see.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Currently, some linker scripts are found by common code in config.mk.
Some are found using CONFIG_SYS_LDSCRIPT, but the code for that is
sometimes in arch config.mk and sometimes in board config.mk. Some
are found using an arch-specific rule for looking in CPUDIR, etc.
Further, the powerpc config.mk rule relied on CONFIG_NAND_SPL
when it really wanted CONFIG_NAND_U_BOOT -- which covered up the fact
that not all NAND_U_BOOT builds actually wanted CPUDIR/u-boot-nand.lds.
Replace all of this -- except for a handful of boards that are actually
selecting a linker script in a unique way -- with centralized ldscript
finding.
If board code specifies LDSCRIPT, that will be used.
Otherwise, if CONFIG_SYS_LDSCRIPT is specified, that will be used.
If neither of these are specified, then the central config.mk will
check for the existence of the following, in order:
$(TOPDIR)/board/$(BOARDDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT)
$(TOPDIR)/$(CPUDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT)
$(TOPDIR)/board/$(BOARDDIR)/u-boot.lds
$(TOPDIR)/$(CPUDIR)/u-boot.lds
Some boards (sc3, cm5200, munices) provided their own u-boot.lds that
were dead code, because they were overridden by a CPUDIR u-boot.lds under
the old powerpc rules. These boards' own u-boot.lds have bitrotted and
no longer work -- these lds files have been removed.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Graeme Russ <graeme.russ@gmail.com>
config.mk only mkdirs $(obj), but we have objects shared with other
boards located on other dirs.
This patch mkdirs the needed dirs for the xlnx-generic boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Use common ppc4xx linker script for xilinx ppc440 and ppc405 related boards.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The duplication of the do_reset prototype has gotten out of hand,
and they're not all in sync. Unify them all in command.h.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
Clean up Makefile, and drop a lot of the config.mk files on the way.
We now also automatically pick all boards that are listed in
boards.cfg (and with all configurations), so we can drop the redundant
entries from MAKEALL to avoid building these twice.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.
Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.
Signed-off-by: Wolfgang Denk <wd@denx.de>
As discussed on the list, move "arch/ppc" to "arch/powerpc" to
better match the Linux directory structure.
Please note that this patch also changes the "ppc" target in
MAKEALL to "powerpc" to match this new infrastructure. But "ppc"
is kept as an alias for now, to not break compatibility with
scripts using this name.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Anatolij Gustschin <agust@denx.de>
The appropriate include/asm-$ARCH directory should already by symlinked
to include/asm so using the whole "asm-$ARCH" path is unnecessary.
This change should also allow us to move the include/asm-$ARCH
directories into their appropriate lib/$ARCH/ directories.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The ml300 board has a number of issues, but nobody cares about this
long-orphaned board any more. Remove it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu>
These boards have special linker scripts right now. We can't use the
common 4xx linker script here. So overrride the linker script (LDSCRIPT)
in board/*/config.mk and choose the board specific version.
Signed-off-by: Stefan Roese <sr@denx.de>
The following changes allow U-Boot to fully relocate from flash to
RAM:
- Remove linker scripts' .fixup sections from the .text section
- Add -mrelocatable to PLATFORM_RELFLAGS for all boards
- Define CONFIG_RELOC_FIXUP_WORKS for all boards
Previously, U-Boot would partially relocate, but statically initialized
pointers needed to be manually relocated.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The top build system sets up HOSTCFLAGS a bit and exports it, but other
places use HOST_CFLAGS instead. Unify the two as HOSTCFLAGS so that the
values stay in sync.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
A recent gcc added a new unaligned rodata section called '.rodata.str1.1',
which needs to be added the the linker script. Instead of just adding this
one section, we use a wildcard ".rodata*" to get all rodata linker section
gcc has now and might add in the future.
However, '*(.rodata*)' by itself will result in sub-optimal section
ordering. The sections will be sorted by object file, which causes extra
padding between the unaligned rodata.str.1.1 of one object file and the
aligned rodata of the next object file. This is easy to fix by using the
SORT_BY_ALIGNMENT command.
This patch has not be tested one most of the boards modified. Some boards
have a linker script that looks something like this:
*(.text)
. = ALIGN(16);
*(.rodata)
*(.rodata.str1.4)
*(.eh_frame)
I change this to:
*(.text)
. = ALIGN(16);
*(.eh_frame)
*(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
This means the start of rodata will no longer be 16 bytes aligned.
However, the boundary between text and rodata/eh_frame is still aligned to
16 bytes, which is what I think the real purpose of the ALIGN call is.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
The boards that get converted here to use the environment for the mac
address rather than global data:
debris
mgcoge
mgsuvd
muas3001
netstal
pn62
sixnet
vcma9
xilinx (the ones that use xilinx_enet)
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Sangmoon Kim <dogoil@etinsys.com>
CC: Heiko Schocher <hs@denx.de>
CC: David Mueller <d.mueller@elsoft.ch>
CC: Niklaus Giger <niklaus.giger@netstal.com>
CC: Wolfgang Grandegger <wg@denx.de>
CC: Dave Ellis <DGE@sixnetio.com>
CC: Ricardo Ribalda <ricardo.ribalda@uam.es>
---
Microblaze platforms use generic settings and to have
many platforms is confusing that's why I decided to remove this
platform from U-BOOT. ml401 tree is sufficient for covering
all Microblaze platforms.
This change will go through microblaze custodian tree.
This BSP should be outside u-boot source tree.
The second reason is that xilinx ppc405 was moved to generic platform.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Most of the bss initialization loop increments 4 bytes
at a time. And the loop end is checked for an 'equal'
condition. Make the bss end address aligned by 4, so
that the loop will end as expected.
Signed-off-by: Selvamuthukumar <selva.muthukumar@e-coninfotech.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Also changed path in all linker scripts that reference this driver
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
As "ppc44x: Unification of virtex5 pp440 boards" did for the xilinx
ppc440 boards, this patch presents a common architecture for all the
xilinx ppc405 boards.
Any custom xilinx ppc405 board can be added very easily with no code
duplicity.
This patch also adds a simple generic board, that can be used on almost
any design with xilinx ppc405 replacing the file ppc405-generic/xparameters.h
This patch is prepared to work with the latest version of EDK (10.1)
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
