Enable driver model for Video to remove the following
compile warning on CM-FX6 SOM based target:
===================== WARNING ======================
This board does not use CONFIG_DM_VIDEO Please update
the board to use CONFIG_DM_VIDEO before the v2019.07 release.
====================================================
This change introduced build error as shown:
LD u-boot
drivers/built-in.o: In function ipu_displays_init'
arm-linux-ld.bfd: BFD (GNU Binutils) 2.29.1 assertion fail elf32-arm.c:9509
Makefile:1621: recipe for target 'u-boot' failed
make: *** [u-boot] Error 1
The DM converted video driver calls ipu_displays_init
in its probe, which inturn calls relevant board_video_skip.
Defining ipu_displays_init in the board file fixes build error.
Target was compile tested, build was clean.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
The SPL does not have DM enabled and therefor still needs to use the
hardware watchdog interface provided by the imx-watchdog driver.
Fixes: broken reset command after f2929d11a6 ("watchdog: imx: Use
immediate reset bits for expire_now")
Signed-off-by: Claudius Heine <ch@denx.de>
Make first step in DT/DM migration. Enable OF_CONTROL only for the main
U-Boot image for now.
Remove mmc_init_main() because board_mmc_init() is not called when
DM_MMC is enabled.
DM_MMC requires DM_GPIO for card-detect to work. That in turn makes gpio
request mandatory. Add code to request/free gpios in platform code.
MMC devices are now numbered according to DT. The SD card is 1, and eMMC
is 2. Account for that in board_mmc_get_env_dev(), BOOT_TARGET_DEVICES,
and has_emmc().
DM_MMC requires BLK. However, the (BLK && !DM_USB) combination disables
USB_STORAGE. Enable DM_USB to preserve USB functionality. Add also
DM_REGULATORS for the USB power controller. This allows us to drop
board_ehci_hcd_init() and setup_usb().
Runtime selection of DT is necessary because of the i.MX6QD vs i.MX6SDL
incompatibility. DT selection does not rely on GPIOs, since DM_GPIO
depends on DT. Instead, we take one "fully featured" DT of each variant.
That should be enough to boot from both SD card and eMMC.
Since we don't select the exact DT, override the generic
show_board_info() that shows the selected DT 'model' field.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
DM for PCI pulls DM for ethernet that also needs other changes described
below to build u-boot and keep existing functionality - ability to update
MAC addresses of FEC ethernet adapter and I210 adapter connected to the
Marvell switch.
- fec_mxc driver with DM needs PHYLIB;
- configuration items are moved from ge_bx50v3.h to ge_bx50v3_defconfig;
- FEC is marked as eth0 because it is always present, so indices changed:
I210 are still probed in the same order;
- board_eth_init() was used by legacy ethernet, setup for enet iomux and
pcie is moved to the board_late_init();
- pci_init() is called from the board_late_init() to initiate PCI bus
probing, so I210 devices are propagated to the device tree;
Signed-off-by: Denis Zalevskiy <denis.zalevskiy@ge.com>
[Describe PHY reset in device tree]
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
DM should be used for USB since 2019.07, it also requires DM for
regulators.
Signed-off-by: Denis Zalevskiy <denis.zalevskiy@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Use vidconsole for output to the LCD, now that DM_VIDEO is used. Write
white text on a black background, like before migrating to DM_VIDEO.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Fixes commit: 0b09f7b150, which converted
to DM_VIDEO, but requires more memory.
[Inspired by 9002e735e7]
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Copy device trees from linux, keeping them as separate files for
each board to ease future sync.
Update board code to use generic bx50v3 dt initially, then select
the specific dt based on board detection.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
This patch introduces support for i.MX28 based XEA board.
This board supports DM/DTS in U-Boot proper as well as DM aware drivers
in SPL (u-boot.sb) by using OF_PLATDATA.
More detailed information regarding usage of it can be found in
./board/liebherr/xea/README file.
U-Boot SPL 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200)
Trying to boot from MMC1
MMC0: Command 8 timeout (status 0xf0344020)
mmc_load_image_raw_sector: mmc block read error
U-Boot 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200)
CPU: Freescale i.MX28 rev1.2 at 454 MHz
BOOT: SSP SPI #3, master, 3V3 NOR
Model: Liebherr (LWE) XEA i.MX28 Board
DRAM: 128 MiB
MMC: MXS MMC: 0
Loading Environment from SPI Flash... SF: Detected n25q128a13 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
OK
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@800f0000 (eth0) using random MAC address - ce:e1:9e:46:f3:a2
eth0: ethernet@800f0000
Hit any key to stop autoboot: 0
Signed-off-by: Lukasz Majewski <lukma@denx.de>
sync defaut Envoronment with customer changes.
Unfortunately they are not changeable, as already
board is in production mode.
Get rid of the big bootcommand and set bootcommand
through Kconfig option.
Signed-off-by: Heiko Schocher <hs@denx.de>
add DM_VIDEO support and remove now unneeded board
code. As we show a bmp logo on boot, call now
bmp_display() from board code and do not use
cfb_console anymore.
Signed-off-by: Heiko Schocher <hs@denx.de>
enable CONFIG_DM_SPI and CONFIG_DM_SPI_FLASH
and get rid of build removal warnings.
define CONFIG_GPIO_ENABLE_SPI_FLASH is not longer
needed, so remove it from config_whitelist.txt
Signed-off-by: Heiko Schocher <hs@denx.de>
Enable DM_GPIO, GPIO_HOG, LED and LED_GPIO as gpio
and LEDs are now defined in DTS. Enable also here
the pinctrl driver, so pinmux setup is also done.
Signed-off-by: Heiko Schocher <hs@denx.de>
add DM_SERIAL support for the aristainetos board, and
remove not used code from board code.
remove CONSOLE_OVERWRITE_ROUTINE.
Signed-off-by: Heiko Schocher <hs@denx.de>
as we switch to support DM and DTS, rework the existing
DTS trees. Change also Linux specific Device trees, goal
is to push this changes to linux.
Collect U-Boot specific changes in separate "*u-boot*" dts
files.
Signed-off-by: Heiko Schocher <hs@denx.de>
remove 2b version of aristainetos board, as it
is easier to make the DM / DTS port and introduce
the 2b board version again (also some more board
version).
Signed-off-by: Heiko Schocher <hs@denx.de>
- Fix latest mainline kernel for rk3308
- Update rk3288-evb config to suport OP-TEE
- Fix for firefly-px30 DEBUG_UART channel and make it standalone
- Script make_fit_atf add python3 support
- Fix rk3328 timer with correct COUNTER_FREQUENCY
- Fix rk3328 ATF support with enable spl-fifo-mode
Enable the ATF in SPL and adjust the SPL STACK/HEAD at the same time to
support ATF entry at 0x40000.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
U-Boot binary has grown in such a way that it goes beyond the reserved
area for the environment variables.
Running "saveenv" followed by a "reset" causes U-Boot to hang because
of this overlap.
Fix this problem by increasing the CONFIG_ENV_OFFSET size.
Also, in order to prevent this same problem to happen in the future,
use CONFIG_BOARD_SIZE_LIMIT, which will detect the overlap in build-time.
CONFIG_BOARD_SIZE_LIMIT does not accept math expressions, so declare
CONFIG_ENV_OFFSET with its direct value instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Firefly Core-PX30-JD4 use UART2M1 while PX30 evb using UART2M0, the U-Boot
proper will use the dts setting to do the IOMUX init, and a separate dts
is needed for px30-firefly.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The Macro has update without update the defconfig, update the defconfig
to make Mcaro correct.
Fixes: ec4fafdf1f ("rockchip: px30: Rename CONFIG_DEBUG_UART2_CHANNEL to...")
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Upstream kernel and rockchip kernel has default enable PSCI which needs
OPTEE in trust word, enable OPTEE support for evb by default and SPL_FIT
option to pack OPTEE with U-Boot proper.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Update the SPL_STACK_R_MALLOC_SIMPLE_LEN which also including space for
STACK and the size may not enough when loding FIT image in SPL.
If the size is not enough, you can see log like this when loding FIT:
U-Boot TPL 2020.01-rc3-00082-g4b19b89ca4-dirty (Dec 05 2019 - 11:52:53)
Trying to boot from BOOTROM
Returning to boot ROM...
U-Boot SPL 2020.01-rc3-00082-g4b19b89ca4-dirty (Dec 05 2019 - 11:52:53 +0800)
Trying to boot from MMC2
And if enable the DEBUG for everyting in SPL, the log will hang at dwmmc
sending CMD16 for 'uboot' loadables binary because this step need a
large stack cost(about 0x2d00).
External data: dst=8400000, offset=72638, size=b3580
Image OS is Trusted Execution Environment
board_fit_config_name_match: rk3288-evb
Selecting config 'rk3288-evb'loadables: 'uboot'
blk_find_device: if_type=6, devnum=1: dwmmc@ff0c0000.blk, 6, 0
blk_find_device: if_type=6, devnum=1: dwmmc@ff0f0000.blk, 6, 1
Sending CMD16
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Orangepi Zero Plus 2 is an open-source single-board computer, available
in two Allwinner SOC variants, H3 and H5. We add support for H3 variant
here, as the H5 is already supported.
H3 Orangepi Zero Plus 2 has:
- Quad-core Cortex-A7
- 512MB DDR3
- microSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG + power supply
Sync dts from linux v5.2 commit:
"ARM: dts: sunxi: h3/h5: Remove stale pinctrl-names entry"
(sha1: 75f9a058838be9880afd75c4cb14e1bf4fe34a0b)
Commit:
"ARM: dts: sun8i: h3: Refactor the pinctrl node names"
(sha1: a4dc791974e568a15f7f37131729b1a6912f4811)
has been avoided as it breaks U-Boot build.
Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Rsync all defconfig files using moveconfig.py
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJd77jyAAoJEB6zHgIOrC/IyYUH/iAUH4wo5qnOBiQU+MJluaiu
D8tMiJH13eW4gWnAqdGrOE9Q763asHIMshQpLK+4eXe4f4mZQ7re4CRNcYJrULeY
2StsJzl4sn/H4P5EiRuUWjkB7wnGRDD6ArH3j1uMJN4lpwCB0ZbqMQZpjt3wI2H4
KuE42d/ll08Aj0AvwdusffLIxlw5M1Z94uQSHoC3UTkPYN4VD5zXgdxv5eH6PZWe
paWmHQ0g7fL4UnYGWa0Jpx10SZpcut06dTeVGpsGiEOhaJHvpjYd4JAs/TTUxhFx
d5ZRjo1fStYmBXQIblhPNlJQkW4cqa/B+81f5aZbN/1yCijJWS2G8anGtY2ikPs=
=f0dF
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2020.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
- First set of u-boot-atmel fixes for 2020.01 cycle:
This set includes a small fix for gpio bank names, one for removing
unused headers (also touches some other boards), and a fix for the QSPI
env read on one of the boards.
The rpi_4_32b_defconfig states that only one DRAM bank is present. This
leads to a wrong configuration of the available DRAM. Fix this by
setting the DRAM bank config accordingly.
Fixes: 193279d784 ("RPI: Add defconfigs for rpi4 (32/64)")
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
bigger than the framebuffer resolution
- reduce dead code in video and console uclass routines
(tested on mx53cx9020, sama5d2_xplained, stm32mp157c-ev1,
stm32f746-disco, stm32f769-disco and wandboard)
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXe//LA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXOqBAJ9N6oTID0v092duxoUoO5xAeqIKxgCfS/YvgGx4
KGgiPWQv0V1bGxXyYNA=
=PoNP
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-2020.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-video
- fix crash and board reset when drawing RLE8 bitmaps
bigger than the framebuffer resolution
- reduce dead code in video and console uclass routines
(tested on mx53cx9020, sama5d2_xplained, stm32mp157c-ev1,
stm32f746-disco, stm32f769-disco and wandboard)
