Enable gmac support for rk3288-vyasa board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Sync gmac dts node from Linux.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add supporting regulators for rk3288-vyasa board, dc12_vbat is
parent regulatorand followed regulators as are child regulators.
regulator naming conversion followed as per schematic for better
readability and easy for identification.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
rk808, SWITCH_REG1 has configured for sdmmc regulator as vcc_sd,
so use the same by renaming vcc33_sd to vcc_sd(as per schematic)
and drop explicit regulator definition from root.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
vdd_log, never used on DCDC_REG1 of rk808 from latest schematic so
remove the same and update the regulator-name as 'vdd_arm' to sync
with existing rk3288 board dts files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Sync rk3288-vyasa board dts from Linux for proper updates and maintenance
- rk3288-vyasa.dts: Similar to Linux dts
- rk3288-vyasa-u-boot.dtsi: u-boot dts changes
Also updated MAINTAINERS for these dts files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Booting a aarch64 Linux kernel requires the image to be placed
text_offset bytes from a 2MB aligned address.
See https://www.kernel.org/doc/Documentation/arm64/booting.txt
booti_setup() takes care about this alignment and will relocate the
image if not properly aligned with memmove(). This can require up
to double the size of the loaded image and therefore accidentally
overwrite content placed there (i.e ramdisk_addr_r) for large kernel
images.
By adding text_offset to the default kernel_addr_r we can prevent that
from happening for kernels larger 18MB and also save a few cycles.
We can assume a text_offset of 0x80000 for most cases, all others will be
handled by booti_setup() anyway.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
use live dt api to get base addr
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use live dt api to get cru base addr.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use live dt api to get cru base addr.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use live dt api to get cru base addr.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use live dt api to get cru base addr.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use live dt api to get cru base addr.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use live dt api to get cru base addr.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
commit 8c4037a09a ("imx: hab: Ensure the IVT DCD pointer is Null prior
to calling HAB authenticate function.") makes the DCD field being NULL a
dependency.
This change though will break loading and executing of existing pre-signed
binaries on a u-boot update i.e. if this change is deployed on a board you
will be forced to redo all images on that board to NULL out the DCD.
There is no prior guidance from NXP that the DCD must be NULL similarly
public guidance on usage of the HAB doesn't call out this NULL dependency
(see boundary devices link).
Since later SoCs will reject a non-NULL DCD there's no reason to make a
NULL DCD a requirement, however if there is an actual dependency for later
SoCs the appropriate fix would be to do SoC version checking.
Earlier SoCs are capable (and happy) to authenticate images with non-NULL
DCDs, we should not be forcing this change on downstream users -
particularly if it means those users now must rewrite their build systems
and/or redeploy signed images in the field.
Fixes: 8c4037a09a ("imx: hab: Ensure the IVT DCD pointer is Null prior
to calling HAB authenticate function.")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Link: https://boundarydevices.com/high-assurance-boot-hab-dummies
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The README.mxc_hab is outdated and need improvements, add the following
modifications:
- Reorganize document and remove duplicate content
- Add CST download link
- Update CST package name
- Align command lines with CST v2.3.3
- Update U-Boot binary name
- Remove CSF padding since is not documented in AN4581
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Currently the High Assurance Boot procedure is documented in two
places:
- doc/README.imx6
- doc/README.mxc_hab
It is better to consolidate all HAB related information into
README.mxc_hab file, so move the content from README.imx6 to
README.mxc_hab.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
commit ed286bc80e ("imx: hab: Check if CSF is valid before authenticating
image") makes use of "__packed" as a prefix to the "struct hab_hdr"
declaration.
With my compiler "gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)" we
get:
./arch/arm/include/asm/mach-imx/hab.h:42:25: error: expected ‘=’, ‘,’, ‘;’,
‘asm’ or ‘__attribute__’ before ‘{’ token
struct __packed hab_hdr {
Fix this problem by including <linux/compiler.h>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
This patch fixes the wrongly included dtsi file which was
breaking mainline support for Engicam i.CoreM6 DualLite/Solo RQS.
Linux commit details for the same change as
"ARM: dts: imx6dl: Include correct dtsi file for Engicam i.CoreM6
DualLite/Solo RQS"
(sha1: c0c6bb2322964bd264b4ddedaa5776f40c709f0c)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
usdhc4 node need to update pinctrl, bus-width and non-removable
properties, sync the same from Linux.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The system call used by mkimage to run dtc redirects stdout to a
temporary file. This can cause problems on Windows (with a MinGW
cross-compiled version). Using the "-o" dtc parameter avoids
this problem.
Signed-off-by: Stefan Theil <stefan.theil@mixed-mode.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
kmerr: verify that malloc and calloc are followed by a check to verify
that we are not out of memory.
badzero: Compare pointer-typed values to NULL rather than 0
Both checks are copied from the Linux kernel archive.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
After the UART was initialized, we may still have bogus data in the
RX queue if it was enabled with incorrect pin muxing before.
So let's flush the RX queue whenever we initialize baud rates.
This fixes a regression with the dynamic pinmuxing code when enable_uart=1
is not set in config.txt on Raspberry Pis that use pl011 for serial.
Fixes: caf2233b28 ("bcm283x: Add pinctrl driver")
Reported-by: Göran Lundberg <goran@lundberg.email>
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Tuomas Tynkkynen <tuomas@tuxera.com>
After the UART was initialized, we may still have bogus data in the
RX queue if it was enabled with incorrect pin muxing before.
So let's flush the RX queue whenever we initialize baud rates.
This fixes a regression with the dynamic pinmuxing code when enable_uart=1
is not set in config.txt.
Fixes: caf2233b28 ("bcm283x: Add pinctrl driver")
Reported-by: Göran Lundberg <goran@lundberg.email>
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Tuomas Tynkkynen <tuomas@tuxera.com>
The following config symbols are only defined once and never referenced
anywhere else:
CONFIG_AT91SAM9263EK
CONFIG_AT91SAM9RLEK
CONFIG_BARIX_IPAM390
CONFIG_BOARD_H2200
CONFIG_EP9301
CONFIG_KZM_A9_GT
CONFIG_PICOSAM
CONFIG_PLATINUM_PICON
CONFIG_PLATINUM_TITANIUM
CONFIG_PM9261
CONFIG_PM9263
CONFIG_PM9G45
CONFIG_SIEMENS_DRACO
CONFIG_SIEMENS_PXM2
CONFIG_SIEMENS_RUT
CONFIG_SMDKC100
CONFIG_SMDKV310
CONFIG_STM32F4DISCOVERY
Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
The following config symbols are only defined once and never referenced
anywhere else:
CONFIG_ARM926EJS
CONFIG_CPUAT91
CONFIG_EXYNOS5800
CONFIG_SYS_CORTEX_R4
Most of them are config symbols named after the respective SoCs which
seems to have been a standard practice at some point.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
The following config symbols are only defined once and never referenced
anywhere else:
CONFIG_DBAU1X00
CONFIG_PB1X00
Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
The @gdsys.cc addresses are supposed to be used for mailing lists.
Switch all occurrences of @gdsys.de mail addresses to their @gdsys.cc
equivalent.
Also, Dirk's address was wrong in one place; fix that as well.
Signed-off-by: Mario Six <six@gdsys.cc>
CONFIG_SYS_CBSIZE determines the maximum length of the kernel command
line, and the default value of 256 is too small for booting some Linux
images in the wild.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Without the volatile attribute, compilers are entitled to optimize out
the same asm(). In the case of __udelay() in syscounter.c, it calls
`get_ticks()` twice, one for the starting time and the second in the
loop to check the current time. When compilers inline `get_ticks()`
they see the same `mrrc` instructions and optimize out the second one.
This leads to infinite loop since we don't get updated value from the
system counter.
Here is a portion of the disassembly of __udelay:
88: 428b cmp r3, r1
8a: f8ce 20a4 str.w r2, [lr, #164] ; 0xa4
8e: bf08 it eq
90: 4282 cmpeq r2, r0
92: f8ce 30a0 str.w r3, [lr, #160] ; 0xa0
96: d3f7 bcc.n 88 <__udelay+0x88>
98: e8bd 8cf0 ldmia.w sp!, {r4, r5, r6, r7, sl, fp, pc}
Note that final jump / loop at 96 to 88, we don't have any `mrrc`.
With a volatile attribute, the above changes to this:
8a: ec53 2f0e mrrc 15, 0, r2, r3, cr14
8e: 42ab cmp r3, r5
90: f8c1 20a4 str.w r2, [r1, #164] ; 0xa4
94: bf08 it eq
96: 42a2 cmpeq r2, r4
98: f8c1 30a0 str.w r3, [r1, #160] ; 0xa0
9c: d3f5 bcc.n 8a <__udelay+0x8a>
9e: e8bd 8cf0 ldmia.w sp!, {r4, r5, r6, r7, sl, fp, pc}
a2: bf00 nop
I'm advised[1] to put volatile on all asm(), so this commit also adds it
to the asm() in timer_init().
[1]: https://lists.denx.de/pipermail/u-boot/2018-March/322062.html
Signed-off-by: Yasushi SHOJI <yasushi.shoji@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Sometimes imximage throws the following error:
CFGS board/freescale/vf610twr/imximage.cfg.cfgtmp
CFGS board/freescale/vf610twr/imximage.cfg.cfgtmp
MKIMAGE u-boot-dtb.imx
Error: No BOOT_FROM tag in board/freescale/vf610twr/imximage.cfg.cfgtmp
arch/arm/mach-imx/Makefile💯 recipe for target 'u-boot-dtb.imx' failed
Later on, when running mkimage for the u-boot.imx it will succeed in
finding the IVT offset.
Looks like some race condition happening during parallel build when
processing mkimage for u-boot-dtb.imx and u-boot.imx.
A proper fix still needs to be implemented, but as a workaround let's
remove the error when the IVT offset is not found.
It is useful to have such message, especially during bring-up phase,
but the build error that it causes is severe, so better avoid the
build error for now.
The error checking can be re-implemented later when we have a proper
fix.
Reported-by: Breno Lima <breno.lima@nxp.com>
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Keep spelling.txt in sync with the version from kernel 4.16-rc4.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Enable DHCP support for this board.
Signed-off-by: Ed Bartosh <ed.bartosh@linux.intel.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.
This commit moves the header code:
include/libfdt.h -> include/linux/libfdt.h
include/libfdt_env.h -> include/linux/libfdt_env.h
and replaces include directives:
#include <libfdt.h> -> #include <linux/libfdt.h>
#include <libfdt_env.h> -> #include <linux/libfdt_env.h>
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
There are no headers for libfdt in lib/libfdt, as they are instead
located in scripts/dtc/libfdt. Specifying lib/libfdt for headers
inclusion in host tools results in using the system libfdt headers,
which is not what we want. Change this to the proper path.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Add a comment indicating that the German key map assumes code page 437.
Add support for character ² (square sign) in the German key map.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
