As the op-tee presence is detected by U-boot, the stm32mp15_optee_defconfig
is identical to stm32mp15_trusted_defconfig and can be removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate OP-TEE driver for trusted and optee defconfig.
This driver allows detection of TEE presence for boot from flash;
CONFIG_STM32MP1_OPTEE is also removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch reduces the stm32mp1 environment size and builds
dynamically the MTD partitions with information from defconfig
(CONFIG_MTDPARTS_...).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch reduces the stm32mp1 environment size and
builds dynamically the DFU board configuration with gpt
and mtd partitions and information from defconfig
(CONFIG_DFU_ALT_RAM0).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move the stm32mp1 common code set_dfu_alt_info() in common directory,
this patch reduce the maintenance effort on this generic part (not board
dependent).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move the stm32mp1 common code board_get_mtdparts() in common directory,
this patch reduce the maintenance effort on this generic part (not board
dependent).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The DHCOR board does exist in multiple variants with different DDR3
DRAM sizes. To cater for all of them, implement DDR3 code handling.
There are two GPIOs which code the DRAM size populated on the SoM,
read them out and use the value to pick the correct DDR3 config.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The AV96 board does exist in multiple variants. To cater for all of
them, implement board code handling. There are two GPIOs which code
the type of the board, read them out and use the value to pick the
correct device tree from an fitImage.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Change-Id: Iddb330b9a66500495885457cbe17edc0eacaaf43
Add default U-Boot configuration for the DHCOR SoM on AV96 board.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Anounce state of BIM switch which defines if U-boot is loaded
and started by preloader or not.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Some systems may use a slightly larger stub to do PSCI for booting the RPi
family. The number of pages has been made configurable so that operating
systems building U-Boot for use in these kinds of environments can reserve
more memory in the EFI memory map.
Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
While the nearly-universal default for the Raspberry Pi family is to use
spin tables and the spin table implementation provided by the Raspberry Pi
Foundation, FreeBSD and others may use a PSCI implementation instead.
Accommodate these setups by allowing them to configure for more than one
page to be reserved in the initial reservation. The default reservation
remains as one page.
Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
When variable setup_console_atag is unset then read default value from OMAP
atags which passed NOLO bootloader to U-Boot.
This would allow to boot Maemo Linux kernel from U-Boot with serial console
settings configured in NOLO bootloader (which loads U-Boot).
So serial console needs to be enabled only at one place, globally in NOLO.
Signed-off-by: Pali Rohár <pali@kernel.org>
Now when code for defining partitions is duplicated at two locations
(option CONFIG_MTDPARTS_DEFAULT in nokia_rx51_defconfig file and macro
OMAP_TAG_PARTITION_CONFIG in rx51.c file) there is no need to have common
macros. Lets inline PART* macros to rx51.c file.
Signed-off-by: Pali Rohár <pali@kernel.org>
In commit commit 278b90ce78 ("configs: Migrate CONFIG_SYS_TEXT_BASE") was
moved definition for CONFIG_SYS_TEXT_BASE option but author probably forgot
to move also comment for lines which are moving. So do it now!
Signed-off-by: Pali Rohár <pali@kernel.org>
Add code to check m4 partition booted or not, we will use this
to runtime set device tree file that passed to Linux Kernel.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Make sure that all devices that are powered up by SPL are powered down
before entering into the u-boot. Otherwise the subsystem/device will
never be powered down by SCFW, due to SPL and u-boot are in different
partitions.
Benefiting from power domain driver, this patch implements the function
"imx8_power_off_pd_devices" to power off all active devices.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Beacon EmbeddedWorks, formerly known as Logic PD, is releasing
a devkit based on the i.MX8M Mini SoC consisting of baseboard +
SOM.
It supports eMMC on the SOM, microSD on the baseboard, various
GPIO, the PINCTRL, and UART.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add initial support for Technexion Pico-iMX8MQ SoM on PicoPI carrier
board. Currently working is ethernet, serial, eMMC. DT is imported
from Linux 5.4.28 ("462afcd6e7ea") .
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
So far the Juno board wasn't implementing reset. Let's just use the
already existing PSCI_RESET based method to avoid any extra code.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Arm Juno board was still somewhat stuck in "hardcoded land", even
though there are stable DTs around, and one happens to actually be on
the memory mapped NOR flash.
Enable the configuration options to let the board use OF_CONTROL, and
add a routine to find the address of the DTB partition in NOR
flash, to use that for U-Boot's own purposes.
This can also passed on via $fdtcontroladdr to any kernel or EFI
application, removing the need to actually load a device tree.
Since the existing "afs" command and its flash routines require
flash_init() to be called before being usable, and this is done much
later in the boot process, we introduce a stripped-down partition finder
routine in vexpress64.c, to scan the NOR flash partitions for the
DT partition. This location is then used for U-Boot to find and probe
devices.
The name of the partition can be configured, if needed, but defaults
to "board.dtb", which is used by Linaro's firmware image provided.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Wrap definition of board_usb_hw_init() around with #ifdef CONFIG_CMD_USB
to avoid warning: 'board_usb_hw_init' defined but not used
[-Wunused-function] when compiling without CONFIG_CMD_USB.
This patch makes sama5d27_som1_ek, sama5d2_ptc_ek and sama5d2_xplained
consistent with other boards that use the same #ifdef to avoid the warning.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Josef Lusticky <josef@lusticky.cz>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
- Add DM model for P1010RDB
- Add I2C DM Model support for P1010RDB, T1042RDB, T2080, T4240RDB,
MPC8548CDS, T1024RDB, P4080, P3041DS, P2041RDB, P2020RDB, P1020RDB,
P5040DS
- Fix reference to READM.qe_firmware
- dts clean up to use -u-boot for px30, rk3399 boards
- dts sycn from upstream kernel for rk3328, rk3399
- add rockchip rng driver
- new board support: rk3328-roc-cc, rk3399-roc-pc,Nanopi M4 2GB
Coreboot is a first-stage bootloader mostly used on x86 devices as an
alternative to UEFI. Coreboot runs in 32-bit mode.
U-Boot currently supports booting from coreboot as a second-stage
bootloader, also in 32-bit mode. However it is useful to be able to run
U-Boot in 64-bit mode. To do this we can have a 32-bit SPL which switches
over the CPU and jumps to a 64-bit U-Boot proper.
Add a new 'coreboot64' board for running 64-bit U-Boot from coreboot. This
uses binman to create an image with a 32-bit SPL and a 64-bit U-Boot.
This allows running 64-bit EFI images on x86, for example, without needing
a native U-Boot port for a board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Compile the legacy PCIe initialization reoutines for P1010RDB
boards only when DM_PCI is not enabled.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add initial support for Google's Coral Dev Board based on i.MX8MQ.
https://coral.ai/products/dev-board
The Phanbell naming has been used here to match the naming convention
used in Google's U-Boot source tree:
https://coral.googlesource.com/uboot-imx/
Co-developed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Tested-by: Marco Franchi <marcofrk@gmail.com>
This patch adds skew register settings for KSZ9131. It checks first
which phy is on the board and then applies the correct skew settings.
Skew settings calculation for the KSZ9131:
The i.MX6 SoC has an output skew tolerance of -100ps to 900ps. All
PCB traces where routed exactly the same length so we can calculate
the skew settings without taking the length into consideration. The
traces are all length matched.
RXC skew (PHY to MAC):
- We use the 2ns DLL controlled delay on the PHY
- We do not use the skew registers
This results in the following values:
RXC
PHY fixed Delay 2000ps
PHY Added Delay 0ps
T_setup_R min 2.00ns
T_setup_R typ 2.00ns
T_setup_R max 2.00ns
T_hold_R min 1.60ns
T_hold_R typ 2.00ns
T_hold_R max 2.40ns
That means we are well within RGMII specs.
TXC skew (MAC to PHY):
- We use the 2ns DLL controlled delay on the PHY
- We then subtract ~0.6ns with TXD[0:3] and TXC clock pad skew
register in a resulting ~1.4ns delay.
This results in the following values under consideration of the
tolerances:
TXC min TXC typ TXC max
MAC min -100ps -100ps -100ps
MAC max 900ps 900ps 900ps
PHY fixed Delay 2000ps 2000ps 2000ps
PHY added Delay -340ps -600ps -859ps
T_setup_T min 1.56ns 1.30ns 1.04ns
T_setup_T typ 2.06ns 1.80ns 1.54ns
T_setup_T max 2.56ns 2.30ns 2.04ns
T_hold_T min 1.04ns 1.30ns 1.56ns
T_hold_T typ 1.94ns 2.20ns 2.46ns
T_hold_T max 2.84ns 3.10ns 3.36ns
This shows that T_hold_T min and T_setup_T min times are out of spec
for RGMII timing. However the KSZ9131 has a minimal value for this time
of 0.8ns which is met under all circumstances.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
This patch determines which phy is placed on the board with the PHY ID
then it sets the same settings for KSZ9031 as before but for KSZ9131
it enables both RXC and TXC delay lines in the PHY.
This will compensate the missing delay from the MAC. Other skew
settings are not needed as the traces on board are routed exactly the
same length
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Tested-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This patches uses the existing functions for interacting with the
KSZ9031 and uses the values appropriate for our board.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Tested-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Use the `do_reset` implementation of `arch/arm/lib/reset.c` in SPL
instead. It is very close to what is done here, anyway, and plays
more nicely with the rest of U-Boot than adding a custom `do_reset`
implementation into board files.
`do_reset` from `arch/arm/lib/reset.c` calls `reset_cpu` with 0 as the
addr parameter while the boards are passing WDOG1_BASE_ADDR. This is
ok because the `reset_cpu` implementation uses WDOG1_BASE_ADDR by
default if 0 is passed in.
Co-Authored-by: Harald Seiler <hws@denx.de>
Signed-off-by: Claudius Heine <ch@denx.de>
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Add a module to configure the tamper and secure violation of
the SNVS using the SCU API.
The module also adds some commands:
- snvs_cfg: Configure the SNVS HP and LP registers
- snvs_dgo_cfg: Configure the SNVS DGO bloc if present (8QXP)
- tamper_pin_cfg: Change the configuration of the tamper pins
- snvs_clear_status: Allow to write to LPSR and LPTDSR to clear
status bits
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
commit b2f5da9dd0 ("rockchip: rk3399: Add Nanopi M4 board support") added
support for Nanopi M4 board with Dual-Channel 4GB LPDDR3-1866 RAM.
This patch adds another variant of NanoPi M4 board with Dual-Channel
2GB DDR3-1866 RAM.
Signed-off-by: Deepak Das <deepakdas.linux@gmail.com>
Add Firefly ROC-RK3399-PC Mezzanine board which is an
extension board on top of roc-rk3399-pc.
Will drop the separate defconfig file, once we support
the board detection at runtime.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The ROC-RK3328-CC from Firefly and Libre Computer Project is a credit
card size development board based on the Rockchip RK3328 SoC, with:
- 1/2/4 GB DDR4 DRAM
- eMMC connector for optional module
- micro SD card slot
- 1 x USB 3.0 host port
- 2 x USB 2.0 host port
- 1 x USB 2.0 OTG port
- HDMI video output
- TRRS connector with audio and composite video output
- gigabit Ethernet
- consumer IR receiver
- debug UART pins
The ROC-RK3328-CC has the enable pin of the SD card power switch tied
to GPIO_0_D6. This pin also has the function SDMMC0_PWREN, which is
muxed by default. SDMMC0_PWREN is an active high signal controlled by
the MMC controller, however the switch enable is active low, and
pulled low (enabled) by default to make things work on boot.
As such, we need to mux away from SDMMC0_PWREN and use GPIO to enable
power to the card. The default GPIO state for the pin is pull-down and
input, which doesn't require extra configuration when paired with the
external pull-down and active low switch.
Deal with this by enabling regulator support in SPL, and setting
"u-boot,dm-spl" for the regulator and other device nodes needed for
muxing the pin.
The device tree file is synced from the Linux kernel next-20200324.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Add DM_ETH support for DPAA1, DPAA2 based RDB platforms: ls1046ardb,
ls1043ardb, lx2160ardb, ls2088ardb, ls1088ardb.
- Add GICv3 support for ls1028a, ls2088a, ls1088a.
- Add lpuart support on ls1028aqds.
- Few bug fixes and updates on ls2088a, ls1012a, ls1046a, ls1021a based
platforms.
Probe the FMan MACs based on the device tree while
retaining the legacy code/functionality.
One notable change introduced here is that, for DM_ETH,
the name of the interfaces is corrected to the fmX-macY
format, that avoids the referral to the MAC block names
which were incorrect for FMan v3 devices (i.e. DTSEC,
TGEC) and had weird formatting (i.e. FM1@DTSEC6, FM1@TGEC1).
The legacy code is left unchanged in this respect.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
mux changes in board file to enable lpuart1 and macro
define for lpuart1 used for mux changes in board configuation
register 13
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In case CONFIG_DM_ETH is enabled, no hardcoding is necessary for
DPAA2 Ethernet devices. Compile out any unnecessary setup when
CONFIG_DM_ETH is activated.
Also, force the PCI devices to be enumerated at probe time.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In case CONFIG_DM_ETH is enabled, no hardcoding is necessary for
DPAA2 Ethernet devices. Compile out any unnecessary setup when
CONFIG_DM_ETH is activated.
Also, force the PCI devices to be enumerated at probe time.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In case of a power interruption, human intervention is required which
is not desirable if the device is installed at a remote location. Drop
yellow LED as it is not much of use. Keep red LED(diy-led) as it is, to
indicate board in full power mode.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Synchronize R-Car Gen3 device trees with Linux 5.6.2,
commit 9fbe5c87eaa9b72db08425c52c373eb5f6537a0a .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The r8a779{5,6,65}_salvator-x and r8a779{5,6,65}_ulcb_defconfig were
building the same target, except for the default DT. The default DT is
however only a detail, as the actual DT to be used to configure U-Boot
is detected automatically based on the CPU ID, hence the default DT is
not meaningful. Unify each three defconfigs per board to reduce the
duplication.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Move GIC redistributor tables initialization to CPU setup function.
This patch introduces a GIC redistributor tables init function, and
moves the function of reserving memory for GIC redistributor tables
to soc.c and adds a argument for the memory size to reserve, BTW
rename the function so that it is more readable.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
As the lower 16bit of the redistributor pending table is reserved
for describing the memory attributes, we must give a 64KB aligned
address to the GIC LPI initialization function.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Program the GIC redistributor tables only when succeeded to reserve memory
for them, otherwise kernel will lose the chance to program them using
allocated memory.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The WRLVL_START values are optimized for old DDR MTA18ASF1G72AZ.
Update DDR struct to set new WRLVL_START values so that the new DIMM
MTA18ADF2G72AZ get optimized and the old DIMM still works.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
- bmips: fix build error when disabling USB
- mips: add option to restore original exception vector base
- mips: fix off-by-one error when clearing gd_data
- mips: minor fixes for compatibility with generic SPL framework
- spl: refactor legacy image loading
- spl: add LZMA decompression support for legacy images
- Makefile: add target to build LZMA compressed U-Boot images
- mtmips: refactor and rewrite low-level init code
- mtmips: add and enable SPL support with LZMA
- mtmips: add support for MT7628 reference board
- mtmips: add support for VoCore/VoCore2 board
-----BEGIN PGP SIGNATURE-----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=2jL1
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2020-04-27' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips
- brcmnand: fix missing code path from Linux driver
- bmips: fix build error when disabling USB
- mips: add option to restore original exception vector base
- mips: fix off-by-one error when clearing gd_data
- mips: minor fixes for compatibility with generic SPL framework
- spl: refactor legacy image loading
- spl: add LZMA decompression support for legacy images
- Makefile: add target to build LZMA compressed U-Boot images
- mtmips: refactor and rewrite low-level init code
- mtmips: add and enable SPL support with LZMA
- mtmips: add support for MT7628 reference board
- mtmips: add support for VoCore/VoCore2 board
Small patch to add support for VoCore/VoCore2 board.
VoCore is open hardware and runs OpenWrt/LEDE.
It has WIFI, USB, UART, 20+ GPIOs but is only one inch square.
It will help you to make a smart house, study embedded system
or even make the tiniest router in the world.
Details about this SoM can be found at "https://vocore.io/v2.html".
Signed-off-by: Mauro Condarelli <mc5686@mclink.it>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch adds support for mt7628 reference board. SPL_DM and DT are not
enabled for SPL to save about 17KiB for u-boot-spl.bin.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch enables SPL for all mtmips boards. And also remove defconfig
files which are intend to build ram bootable u-boot files.
SPL_DM and OF_CONTROL are enabled for both boards.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Create special function for reading bootmode on Versal and ZynqMP.
Zynq is using specific function (without mask) already.
Future patches will be calling this function from different location too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use register intstead of static variable to store HSDK init status as
we want to avoid the situation when we reload U-boot via MDB after
previous init is done but HW reset (board reset) isn't done. So
let's store the init status in unused register - CREG_CPU_0_ENTRY
so status will survive after U-boot is reloaded via MDB.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
For HSDK-4xD we do additional AXI bridge tweaking while doing
hsdk_init command:
- we shrink IOC region.
- we configure ARC HS CORE SLV1 aperture depending on
haps_apb_location environment variable.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Add support for CSM enable/disable and CSM relocation via
hsdk_init command. We allow to relocate CSM to the beginning of
any aperture even if HW support finer granularity.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
HSDK-4xD has other GPU type so it consumes only GPU core clock.
Even we have additional GPU clock dividers they are not routed
to anything. So drop information about those additional clocks
in hsdk_clock print_all command.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
HSDK-4xD has HDMI working so let's print info about HDMI clocks.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
ARC HS CPU in HSDK-4xD has ARC ID = 0x54, so fix headerize script
accordingly.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Add quirk for HSDK-4xD - due to HW issues HSDK can use any pulse
polarity but HSDK-4xD require active low polarity of cpu_start pulse.
So use low polarity of cpu_start pulse for both board.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Add initial HSDK-4xD board support.
The ARC HS4x/HS4xD Development Kit includes a multicore ARC HS4xD-based
chip that integrates a wide range of interfaces including Ethernet,
HDMI, WiFi, Bluetooth, USB, SDIO, I2C, SPI, UART, I2S, ADC, PWM and
GPIO, as well as a Think Silicon GPU.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This commit adds common arch support for Actions Semi Owl
series SoCs and removes the Bubblegum96 board files.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
The commit was added as a workaround required in QEMU when using BBL as
the supervisor binary interface (SBI) for Linux. We are now using
OpenSBI to provide the SBI, the workaround is therefore not required
anymore and can be removed.
This reverts commit 897206c5cc.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Fix boot on am335x guardian board
- Increase OPSI speed on AM65x and J721E devices
- Use JTAD register for identifying K3 devices.
- Update TI entry in MAINTAINERS file.
Add support for backplane kr on t208xqds: remove board specific fixups
on t208xqds for ethernet interfaces specified in device tree as
supported backplane modes.
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for backplane kr on lx2160aqds: remove board specific fixups
on lx2160aqds for ethernet interfaces specified in device tree as
supported backplane modes.
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for backplane kr on ls1046aqds: remove board specific fixups
on ls1046aqds for ethernet interfaces specified in device tree as
supported backplane modes.
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch is to define esdhc_status_fixup function for ls1028a to disable
SDHC1/SDHC2 status in device tree node if not selected.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
If the board is configured without CONFIG_GIC_V3_ITS, an error occurs:
board/freescale/lx2160a/lx2160a.c: In function ‘ft_board_setup’:
board/freescale/lx2160a/lx2160a.c:673:6: error: unused variable
‘gic_lpi_base’ [-Werror=unused-variable]
673 | u64 gic_lpi_base;
| ^~~~~~~~~~~~
Let's define the variable as __maybe_unused.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
After the
commit 4213609cc7 ("drivers: core: use strcmp when find device by name")
the exact DTS node name for PMIC device must be provided.
This patch fixes this issue by providing full DTS node name ('mc34708@8').
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chug <jh80.chung@samsung.com>
Use DM_ETH instead of legacy networking. Add VIO as a fixed regulator
to the relevant device-trees and augment the FEC node with properties
for the reset GPIO.
It should be noted that the relevant properties for the reset GPIO
already exist in the PHY node (reset-gpios, reset-delay-us,
reset-post-delay-us) but U-Boot currently ignores those and only
supports the bus-level reset properties in the FEC node
(phy-reset-gpios, phy-reset-duration, phy-reset-post-delay).
Signed-off-by: Harald Seiler <hws@denx.de>
Since CONFIG_DISPLAY_BOARDINFO_LATE is no longer used, the checkboard()
function is no longer called.
As it is useful to print the board revision, print it inside
board_late_init() instead.
Also, to avoid GPIO errors related to using a GPIO without requesting it,
move the gpio_request(REV_DETECTION, "REV_DETECT") call prior to its
usage.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Heiko Schocher <hs@denx.de>
On wandboard variants prior to revD1, there is no PMIC populated, so
do not print an error when the reading of the device ID register fails.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Heiko Schocher <hs@denx.de>
The detection of the revD1 version is based on the presence of the PMIC.
Currently revb1 device trees are used for mx6q/mx6dl variants, which
do not have the PMIC nodes.
This causes revD1 boards to be incorrectly be detected as revB1.
Fix this issue by using the revd1 device trees, so that the PMIC node can be
found and then the PMIC can be detected by reading its register ID.
Imported the revd1 device trees from mainline kernel version 5.7-rc1.
Reported-by: Heiko Schocher <hs@denx.de>
Reported-by: Derek Atkins <derek@ihtfp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Derek Atkins <derek@ihtfp.com>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Adjust DRAM size in case BL32 secure payload is loaded (OP-TEE/Trusty),
so during MMU initialization U-Boot won't touch this mem area.
BL32 is loaded to the end of DRAM, bl32 payload size is read from
rom_pointer[1]. This relates to the issue described in
59efa6b52b("imx8m: Fix MMU table issue for OPTEE memory").
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Adjust DRAM size in case BL32 secure payload is loaded (OP-TEE/Trusty),
so during MMU initialization U-Boot won't touch this mem area.
BL32 is loaded to the end of DRAM, bl32 payload size is read from
rom_pointer[1]. This relates to the issue described in
59efa6b52b("imx8m: Fix MMU table issue for OPTEE memory").
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
After triggering a "reboot" command in Linux the following
hang in SPL is observed:
U-Boot SPL 2020.04 (Apr 15 2020 - 10:49:29 -0300)
Normal Boot
WDT: Not found!
Trying to boot from MMC2_2
spl: mmc init failed with error: -70
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
This error happens because the CMD_ERR bit is set in the IRQ status
register after booting from Linux.
To ensure a fresh start, force the VMMC supply to get unpowered first.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Ethernet, usdhc2 and i2c1 interfaces are probed by dm drivers.
Therefor init functions in board file are not necessary.
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@ew.tq-group.com>
Keep code for non-dm configuration of baseboard WRU4.
It cannot be upgraded to device model as
we have no suitable device tree for it.
These changes were not run-tested on WRU4,
only compile-tested.
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@ew.tq-group.com>
reason: SYS_TEXT_BASE was moved to Kconfig. Give reasonable defaults
in board specific Kconfig.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@ew.tq-group.com>
mx6ul_evk uses DM_ETH, so there is no need to have board code
to setup the FEC IOMUX and to register the network ports via the
old board_eth_init() method.
Remove these FEC related pieces of code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Update reference in files detected by
scripts/documentation-file-ref-check
doc/README.<board> => board/<board>/README
Files moved in board directory in
commit 702e6014f1 ("doc: cleanup - move board
READMEs into respective board directories")'
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Update reference in many files detected by
scripts/documentation-file-ref-check
README.imx8image => imx/mkimage/imx8image.txt
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Update reference in many files detected by
scripts/documentation-file-ref-check
README.imximage => imx/mkimage/imximage.txt
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Currently we are not able to test reservations created by ft_board_setup().
Implement ft_board_setup() to create an arbitrary reservation and enable
OF_BOARD_SETUP.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromum.org>
Use the correct macro to test presence CONFIG_LED:
replace CONFIG_IS_ENABLED(CONFIG_LED) by CONFIG_IS_ENABLED(LED)
Issue see during review unrelated patch
"board: stm32mp1: update management of boot-led"
http://patchwork.ozlabs.org/patch/1264823/
Cc: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate ARCH_SUPPORT_TFABOOT and replace the arch stm32mp
specific config CONFIG_STM32MP1_TRUSTED by the generic CONFIG_TFABOOT
introduced by the commit 535d76a121 ("armv8: layerscape: Add TFABOOT
support").
This config CONFIG_TFABOOT is activated for the trusted boot chain,
when U-Boot is loaded by TF-A.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add DT entries, Kconfig entries and board-specific entries to configure
FMC2 bus and make KS8851-16MLL on that bus accessible to U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Use the new a3700_fdt_fix_pcie_regions function in turris_mox.c so that
MOX boards with 4 GB RAM are fully supported.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
In order to support MOX boards with 2 GB or 4 GB RAM, we use the new
Armada-3700 generic code for memory information structures. This is done
by removing dram_init and dram_init_banksize from turris_mox.c, in order
for the generic, weak definitions to be used.
Also for boards with 4 GB RAM it is needed to increase
CONFIG_NR_DRAM_BANKS to 2 in turris_mox_defconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Sort #includes alphabetically, the only exception is common.h, which is
included first in most parts of U-Boot.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Use macro MVEBU_REGISTER to access register addresses instead of
hardcoded addresses.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Patch Linux's device tree according to which Mox modules are connected.
Linux's device tree has all possible Mox module nodes preprogrammed, but
in disabled state.
If MOX B, MOX F or MOX G module is present, this code enables the PCI
node.
For the network modules (MOX C, MOX D and MOX E) are present, the code
enables corresponding ethernet and swtich nodes and DSA connections.
For the SFP cage the SFP GPIO controller node and SFP node are also
enabled.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The SPI clock signal changes value when the SPI configuration register
is configured. This can sometimes lead to the device misinterpreting
the enablement of the SPI controller as actual clock tick.
This can be solved by first setting the SPI CS1 pin from GPIO to SPI mode,
and only after that writing the SPI configuration register.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Switch to explicitly using the Pro variant DT, which has been
available since Linux 4.11.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Migrate the values for ENV_SIZE and ENV_OFFSET into board specific
Kconfig defaults so they're more accessible for configuration.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Add reasonable default SPI offsets and ENV size when configured to
boot from SPI flash.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Unify the location of DT selection into board_late_init instead of
split between detection and static configuration paths.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
The mPCIe slots on ClearFog Pro and ClearFog Base may be alternately
configured for SATA usage.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
While newer Linux kernels provide autoconfiguration of SFP, provide
an option for setting in U-Boot Kconfig for use prior to booting.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Add a unique entry for ClearFog Base variant, reflected in the board
name and adjusted SerDes topology.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Make the board version printed indicate the Pro variant default.
Also adjust static name casing to match what is expected for
EEPROM product name to share string constants.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch enables the guardian board to provide feedback
about the boot stage in headless mode. The on-board led
would behave in the following pattern
* U-boot -> GLOW LED
* Linux -> BLINK LED [HEART-BEAT PATTERN]
Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
For some layouts it is necessary to adjust the CK_DELAY parameter to
successfully complete DDR training. Add the ability to specify the
CK_DELAY in the mv_ddr_topology_map.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Pull in changes that have been pending in our 'next' branch. This
includes:
- A large number of CI improvements including moving to gcc-9.2 for all
platforms.
- amlogic, xilinx, stm32, TI SoC updates
- USB and i2c subsystem updtaes
- Re-sync Kbuild/etc logic with v4.19 of the Linux kernel.
- RSA key handling improvements
- sync all Amlogic DT from Linux v5.6-rc2
- MMC clock fixups
- add support for Libre Computer AML-S905D-PC and AML-S912-PC
-----BEGIN PGP SIGNATURE-----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=PiOt
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200406' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic into next
- clk: meson-g12a: missing break
- sync all Amlogic DT from Linux v5.6-rc2
- MMC clock fixups
- add support for Libre Computer AML-S905D-PC and AML-S912-PC
This fixes the issue when PHY auto negotiation never completes.
Fixes: 431cd76dd8("colibri_imx6: migrate to DM_ETH")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Parameter order is not correct based on zynqmp_mmio_write() declaration.
Fixes: be52372ff1 ("arm64: zynqmp: Use zynqmp_mmio_read/write functions")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Delay required for clock propagation is tighly coupled with initialization
done in psu_init(). That's why call it also for u-boot proper with
CONFIG_ZYNQMP_PSU_INIT_ENABLED enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
board_early_init_f() is the right location where debug uart can be
configurated (after MIO initialization).
The patch is taking this call from SPL to also make it available for U-Boot
proper.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP mini configurations works without PMU firmware that's why there is
no reason to enable the driver and check if it was probed properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Multi boot register can be used for using different boot images and design
better boot strategy. Let EL3 SPL or U-Boot to read it and print it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for the Amlogic based libretech-pc platform.
This platform comes with 2 variant, based on the s905d or s912 SoC.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[narmstrong: update board/amlogic/q200/MAINTAINERS]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Jetson Nano Developer Kit is a Tegra X1-based development board. It
is similar to Jetson TX1 but it is not pin compatible. It features 4GB
of LPDDR4, a SPI NOR flash for early boot firmware and an SD card slot
used for storage.
HDMI 2.0 or DP 1.2 are available for display, four USB ports (3 USB 2.0
and 1 USB 3.0) can be used to attach a variety of peripherals and a PCI
Ethernet controller provides onboard network connectivity. NVMe support
has also been added. Env save is at the end of QSPI (4MB-8K).
A 40-pin header on the board can be used to extend the capabilities and
exposed interfaces of the Jetson Nano.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
T210 CBoot is now doing the full pinmux and GPIO init, based on the DTB
tables. Remove pinmux/GPIO init tables & code from all T210-based builds
below:
p2371-2180 aka TX1
p2371-0000
e2220-1170
p2571
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
compatibility with stm32mp15_dhcom_basic_defconfig
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl6EiK0ACgkQ4rK92eCq
k3V6DggAhU7jE5MGs9A7En+YpANXbJ4tl56IZIjdzPzEjA2G3yuBv/DLci/w27aF
eaP83ayI/ZrVtevEBFomP0JRrzQc9r/ot+USVugGsoAigLbzJc5uba42FGn09Olh
uKkst0Fb7uPRzZQNwRc7hTKVSLvT11c0oPQyhhJM2djPDTETDry+RPnEFQ41SEUt
bNILmj0VRzikzbe5RXFWWYMUWBrt22pG2LLhog+WSRSpqrWM2zES64NnwAXxD/mR
YIQFZIZ6eWW2Otp+qzenkg5ZWIMVWRyUBAP5e0auKRE8TGWAXgBcoFRTRLf7oA/P
yr3TTBMWiPdqdXNe3MYzAiTpm7jrtg==
=RALH
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200401' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Fix device tree of Avenger96 board from Arrow Electronics and add
compatibility with stm32mp15_dhcom_basic_defconfig
Use DT /aliases node to establish a stable phandle to the configuration
EEPROM. This permits the configuration EEPROM to be moved e.g. to a
different address or a different bus. Adjust the board code to handle
new phandle lookup.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
If the DM_ETH is enabled, the board-specific ethernet registeration
should be disabled, make it so.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add code to reset the board through PMIC, by writing the required
PMIC registers in the CPU reset handler.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add config to enable the PFE and ETH support.
Also change the pfe secure boot header address.
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1046A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1043A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The SDHC1_DAT4 signal could be routes to SDHC1_VS or SDHC1
adapter slot for SDHC1 usage. When SDHC1 is selected in RCW,
do not force to route it to SDHC1 adapter slot if find it
has already been configued for SDHC1_VS.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Set VID to 800 mV for Rev1 and set VID as per switch settings
for Rev2.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Program GIC LPI configuration table:
1. Redistributor PROCBASER configuration table (which
is common for all redistributors)
2. Redistributor pending table (PENDBASER), for all the
available redistributors.
Signed-off-by: Manish Tomar <manish.tomar@nxp.com>
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Update "board_fix_fdt" with correct counter value "i".
This will fix the issue while fetching the "reg_names"
resource from fdt after fixup.
Signed-off-by: Vikas Singh <vikas.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Since commit 8e9a8d0d0c ("rockchip: elgin-rv1108: use board_early_init_f
for per-boar init") the function that configure the board GPIOs is no
longer called since CONFIG_BOARD_EARLY_INIT_F=y is not selected.
These GPIOs do not need to be configured in such early stagem, so change it
to rk_board_late_init() and also select CONFIG_BOARD_LATE_INIT=y
to fix the regression.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use syscon API to get grf base instead of get from dts.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use syscon API to get grf base instead of get from dts.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Need to increase the LPDDR2/LPDDR3 the voltage vdd2_ddr: buck2
form 1.2V to 1.25V for 32bits configuration.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Display the reference MBxxxx found in OTP49
only for STMicroelectronics boards when CONFIG_CMD_STBOARD
is activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
# Conflicts:
# board/st/stm32mp1/stm32mp1.c
Update the command stboard to support the updated coding of OTP 59 with
finished good.
The ST product codification have several element
- "Commercial Product Name" (CPN): type of product board (DKX, EVX)
associated to the board ID "MBxxxx"
- "Finished Good" or "Finish Good" (FG):
effective content of the product without chip STM32MP1 (LCD, Wifi, …)
- BOM: cost variant for same FG
(for example, several provider of the same component)
For example
- commercial product = STM32MP157C-EV1
- Finished Good = EVA32MP157A1$AU1
Booth information are written on board and these information is also saved
in OTP59:
bit [31:16] (hex) => Board id, MBxxxx
bit [15:12] (dec) => Variant CPN (1....15)
bit [11:8] (dec) => Revision board (index with A = 1, Z = 26)
bit [7:4] (dec) => Variant FG : finished good (NEW)
bit [3:0] (dec) => BOM (01, .... 255)
The updated command is:
stboard [-y] <Board> <VarCPN> <Revision> <VarFG> <BOM>
And the displayed STMicroelectronics board identification is:
Board: MB<Board> Var<VarCPN>.<VarFG> Rev.<Revision>-<BOM>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Lock the OTP used for board identification for the ST boards after
programming.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Read the value directly from the OTP and no more of the shadows
to avoid the need of reboot after stboard command to have correct value.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Update management of misc_write, which now return length of data
after the commit 8729b1ae2c ("misc: Update read() and write()
methods to return bytes xfered")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
K3 J721E:
* OSPI boot support
* Support for loading remote cores in R5 SPL
* PMIC ESM Support
* Minor fixes for R5F and C7x remoteproc drivers
K3 AM654:
* Update AVS class 0 voltages.
* Add I2C nodes
DRA7xx/AM57xx:
* Fixed Android boot on AM57xx
AM33/AM43/Davinci:
* switch to driver model for the net and mdio driver for baltos
* Add DM/DTS support for omap video driver
* Enable fastboot on am335x-evm
As there is only one mx31pdk config file and with upcoming updates to
the Kconfig parsing logic, rather than have an entry in
board/freescale/mx31pdk/Kconfig, move this single setting to the
defconfig file.
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Magnus Lilja <lilja.magnus@gmail.com>
In a few places we have Kconfig entries that set SPL_LDSCRIPT to what is
the default value anyways. Drop these.
Cc: Michal Simek <monstr@monstr.eu>
Cc: Rick Chen <rick@andestech.com>
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com> (for Microblaze)
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
This fixes the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This fixes the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Instead of resetting the ethernet phy through functions in imx8mq_evk.c, let the
driver reset the phy via dts description adding a reset duration of 10 ms
following atheros 8031's datasheet recommendation.
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Convert imx6sabresd ethernet to driver model to fix the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
On the aristainetos2c boards the PMIC needs to be initialized,
because the Ethernet PHY uses a different regulator that is not
setup per hardware default. This does not influence the other
versions as this regulator isn't used there at all.
Signed-off-by: Heiko Schocher <hs@denx.de>
The OP-TEE binary to use is renamed to v2 as the v1 binary has been
deprecated and is no longer built by default.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Add entries for the newly created documentation files in reST
format.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Convert README to reStructuredText format.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: spell out U-Boot correctly]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Add initial support for the ABB SECU board, which is an ArriaV-based
SoCFPGA system with ethernet and booting from Denali NAND.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Now k3-image-gen[0] is the official repository for generating sysfw.itb
Update the same in AM65x and J721e README.
[0] https://git.ti.com/cgit/k3-image-gen/k3-image-gen/
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Fix building errors if CONFIG_DM_VIDEO is enabled. This is the only
u-boot board that enables CONFIG_AM335X_LCD and from which I started
to develop the version of the frame buffer driver that supports the
driver model.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Initialize both ESM and ESM_PMIC support if available for the board.
If support is not available for either, a warning is printed out.
ESM signals are only properly routed on PM2 version of the J721E SOM,
so only probe the drivers on this device.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Change plain test README to rst format and move this file
in documentation directory.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
DEVICE_TREE variable is not exported from dts/Makefile that's why it is
necessary to setup directly before use.
Fixes: 312f2c5b14 ("arm: xilinx: Use device tree which can be passed on cmd line")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The board has two push button connected to MIO pins
50 and 51, which have a pull-down resistor and are
connected to 1.8V when pressed.
These two pins are wrongly initialized with internal
pull-up enabled so they are reported as 1 all the time
with no change when pressed.
Disable the internal pull-up to fix the issue.
Signed-off-by: Milan Obuch <u-boot@dino.sk>
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added support for onboard LED's and push button. When powered board will be
in low power mode(yellow LED), on button press, board enters full power mode
(red LED) and boots u-boot.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
roc-pc-rk3399 board has one user button & three user LED's. Currently
we don't have any code support for these devices. Since button and LED's are
specific to roc-pc-rk3399 board, split it into its own board file and add code
support here.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- DT alignment with kernel v5.5-rc7 for stm32mp1 boards
- fix STM32 image format for big endian hosts in mkimage
- solve warnings in device tree and code for stm32mp1 boards
- remove fdt_high and initrd_high for stm32 and stih boards
- add support of STM32MP15x Rev.Z
- update stm32mp1 readme
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl5GcB0ACgkQ4rK92eCq
k3Wr9gf/dDPJi6UBhLDio/IVKDBddOEUN0Lwdr9W0upL+DrdvEOyNyMSEKuLccIE
UTd1NmNNwcvgDRaPvB5o3R7twWItTW0cYlmVkFSZ228aq6xdf/SElN2OUD6B9Gh+
8bi6oVLu41TNMYn4VYxsEftcT2megfH8s+SH/FlvR5ua1yCC1vyrytEQjPIbJAB2
sa90ewDyp5EYqGLdAk6AVjPLeNZsaleGwuyLf04PoC2xhn+3HTEKJCJN4O46aJUr
0GUI7YN7pTjIfZdYfFqjcwoQV1xV2HtbjCTcOb8Td8TEYjIoILF8tSyfIwDXWGB5
zMQIQxUdQyNiqdBPFcnkAufjk+zLIQ==
=0dG+
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200214' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- add DH Electronics DHCOM SoM and PDK2 board
- DT alignment with kernel v5.5-rc7 for stm32mp1 boards
- fix STM32 image format for big endian hosts in mkimage
- solve warnings in device tree and code for stm32mp1 boards
- remove fdt_high and initrd_high for stm32 and stih boards
- add support of STM32MP15x Rev.Z
- update stm32mp1 readme
Change the dfu functions dfu_otp_read and dfu_pmic_read to static,
this patch avoids warning when compiling with W=1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add include for dfu, add prototype for set_dfu_alt_info
and avoid warning when compiling with W=1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Update readme:
- list the supported SOC and change family to STM32MP15x
- add warning on OTP write and prerequisite:
check if MAC address is not yet provisioned.
- Use filesize for mmc write command (avoid to write all partition
with ${partsize}). ${filesize} and ${partsize} are set by previous
load command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
On am571x-idk there can be following configurations based on Jumper J51
and LCD panel detected.
1) J51 removed (6port): 6 port Ethernet. Disable LCD panel.
2) J51 placed (LCD) + Panel detected: 4 port Ethernet with appropriate LCD.
3) J51 placed (LCD) + Panel not detected/not supported.
Configuration 3 is considered invalid as we can't use display nor ICSS1
ethernet ports due to hardware muxing. Alert the user to fix the
configuration and prevent boot.
Alternative was to allow boot and limit to 4 port Ethernet with no display
but this involved introduction of another DTB for the kernel and was
considered not worth the hassle.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier
board. This is an SoM with STM32MP15xx and an evaluation kit. The
baseboard provides Ethernet, UART, USB, CAN and optional display.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
It's a very rare if at all existing occasion when ARC CPU template
is used as is w/o any changes - in the end it's a beauty and competitive
advantage of ARC cores to be tailored for a particular use-case - and
so it doesn't make a lot of sense to offer template-based "-mcpu" selection.
Given for each and every platform we end-up adding quite a few more flags
it's logical to move "-mcpu" selection to platform's definition as well
which we exactly do here.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Given now nsim_hs38 configuration is usable on QEMU and in QEMU
we have Virtio working perfectly fine the next logical step
is to add support of supported & known to work net & bkl to this
config.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl48iogACgkQfxc6PpAI
reaVzAf/an3/yKe6r3CVWlcRV6H/dVg1ApnnLpX7jS0p0b++oCVvOiy7z1WPXj3k
b1SSgENDeeZ/8EHio+Gf7ZidH/TGEj7L6YEFwd1t60GMkZiWEkNf4Z53tw482YG+
96hoPD+ySTW+ddIdVHWAFG2I4aEiKHANJAp/ItNdD+rLbrEwNQy+eiK5JTOk80B6
/X8AJCLZeAC1s7vs+2+WolgjT78QGzA9HHalMiublcqh0ivKKk0QeQiOKKPe8JYJ
om5YY1TxayQ60Xmo5f39/SBfzEEklxw83sU9o1tBeYzyVUpu7fQdkxiDbWdsij77
DgwLdeYQJGbN+hdSWE0gjTqyhW+lWA==
=KRoA
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-6feb20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
sandbox conversion to SDL2
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
Drop PPD_UART_PAD_CTRL since it matches defaults.
Enable DM serial and MXC uart.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Add backlight and panel devicetree definitions
Use UCLASS_PANEL to enable backlight via display enable handler
Remove old explicit gpio code for handling backlight
Use cls command to initiate display in HW agnostic manner
Enable DM regulator and pwm
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Enable DM_VIDEO for mx53ppd.
Enable DM_REGULATOR_FIXED and DM_PWM for the backlight.
Remove unused MX53PPD_LCD_POWER.
Remove old (incorrect) setup_iomux_lcd.
Enable backlight via display enable handler.
Use cls command to initiate display in HW agnostic manner.
Modify `failbootcmd' to use lcdputs.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Remove old (pre-DM) i2c setup code.
Enable DM i2c.
Convert common code to use DM rtc.
Convert common code to read VPD from eeprom partition.
Convert the generic i2c PMIC init code to use the new da9063 driver.
mx53ppd only:
Correct RTC compatible in device tree.
Enable MXC DM i2c driver.
Define CONFIG_SYS_MALLOC_F_LEN so that DM is available in pre-reloc.
Make GPIO banks available during preloc, since initialisation is done
in board_early_init_f().
Add gpio_request() calls to satisfy the DM_GPIO compatibility API.
Remove unused power configuration.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
This should help keeping the screen black when booting the kernel.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Convert imx6sabresd PCI to driver model to fix the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_PCI Please update
the board to use CONFIG_DM_PCI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
After the conversion the following commands were used for testing:
=> pci enum
PCI: Failed autoconfig bar 10
PCI: Failed autoconfig bar 10
=> pci 1
Scanning PCI devices on bus 1
BusDevFun VendorId DeviceId Device Class Sub-Class
Reviewed-by: Fabio Estevam <festevam@gmail.com>
commit 88718be300 ("mtd: rename CONFIG_NAND -> CONFIG_MTD_RAW_NAND")
moved CONFIG_NAND -> CONFIG_MTD_RAW_NAND. Adapt board code to this
change, as last merge did not respect the above commit.
Signed-off-by: Heiko Schocher <hs@denx.de>
When pmic_get() is used with DM the first parameter must be
the complete node name plus the unit address, so fix it
accordingly
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Explicitly configure GPIO0_0 in SPL, which controlls 3V3 voltage
on the XEA board (it also supplies TIVAs).
This code would enable TIVAs power supply early (also when board
uses the falcon boot).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The 'local-mac-address' property needs to be adjusted to the MAC address
value stored in U-Boot's 'ethaddr' env variable.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Currently there are two targets for the i.MX6SX SabreSD board:
mx6sxsabresd_defconfig and mx6sxsabresd_spl_defconfig.
This brings additional maintainance effort without a clear
advantage.
Keep only the mx6sxsabresd_defconfig one and remove
mx6sxsabresd_spl_defconfig to keep it simpler.
Also remove the SPL related code from the board file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Assign Igor Opaniuk as a board maintainer.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Add README with build steps for U-boot and TF-A for Verdin iMX8M Mini SoM.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad
2GB WB IT V1.0A module. They are now strapped to boot from eFuses which
are factory fused to properly boot from their on-module eMMC. U-Boot
supports booting from the on-module eMMC only, SDP support is disabled
for now due to missing i.MX 8M Mini USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100)
Normal Boot
Trying to boot from MMC1
NOTICE: Configuring TZASC380
NOTICE: RDC off
NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty
NOTICE: BL31: Built : 01:11:41, Jan 25 2020
NOTICE: sip svc init
U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100)
CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz
Reset cause: POR
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial#
06535149
Net: eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
Verdin iMX8MM #
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Add support for storing configuration for Verdin iMX8M Mini and
Nano SoMs in Toradex config block.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Add support for storing configuration for Apalis iMX8X SoM
in Toradex config block.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Assign Alex Nemirovsky as custodian for all
Cortina Access (CA) for ARM and MIPS based SoCs.
Currently Cortina Access CAxxxx family of SoCs support both
ARM and MIPS ISA. Drivers have cross platform support for
both architectures.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Most files don't need this header and it pulls in quite of lots of stuff,
malloc() in particular. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This function is actually intended to read a string rather than a
property. All of its current callers use it that way. Also there is no way
to return the length of the property from this function.
Rename it to better indicate its purpose, using ofnode_read as the prefix
since this matches most other functions.
Also add some tests which are missing for these functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Inside Kconfig we must not use the CONFIG_ prefix with the imply statement.
Fixes: 28e3c39e53 ("board: freescale: ls1012a2g5rdb: enable network
support on ls1012a2g5rdb")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1021A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1012A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support of "qixis_reset emmc" command for lx2160a based platforms
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Coreutils command nproc can be used on Linux and BSD to count the number of
available CPU cores. Use this instead of relying on the parsing of the
Linux specific proc file system.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
XOM pins provide information for iROM bootloader about the boot device.
Those pins are mapped to lower bits of OP_MODE register (0x10000008),
which is common for all Exynos SoC variants. Set the default MMC device id
to reflect the boot device selected by XOM[7:5] pins (2 for the SD or 0 for
the eMMC).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
