Add ICID setup for the platform devices contained on this chip: usb,
sata, sdhc, sec. The ICID macros for SEC needed to be adapted because
the format of the registers is different.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
BRDCFG4[USBOSC] and BRDCFG5[SPR] register field of Qixis device is used
to control SPI and other IP signal routing.
USBOSC:
0= SPI_CLK used as external USB REFCLK input driven with 24.000 MHz.
SPI devices are unusable in this mode.
1= SPI_CLK used as SPI clock.
SPI devices are usable in this mode. USB block is clocked from
internal sources
SPR[3:2]:
SPI_CS / SDHC_DAT4:7 Routing (schematic net CFG_SPI_ROUTE[3:2]):
00= SDHC/eMMC 8-bit
01= SD Card Rev 2.0/3.0
10= SPI on-board memory
11= TDM Riser / SPI off-board connector.
The default value is 00 if an SDCard/eMMC card is selected as the boot
device.
SPR[1:0]:
SPI_SIN/SOUT/SCK Routing (schematic net CFG_SPI_ROUTE[1:0]):
00= SDHC Sync loop
01= TDM Riser / SPI off-board connector.
10= SPI on-board memory.
11= SPI off-board connector.
By default, the SPI feature is not available, so we need to configure
the above register fields to select the route to the SPI feature.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Flexcan in LX2160ARDB is controlled by FPGA register boardcfg4
bit 5. enable this bit so that flexcan is enabled in LX2160ARDB.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM
I2C API when DM_I2C is used.When DM_I2C_COMPAT is not enabled for
compilation, a compilation error will be generated. This patch
solves the problem that the i2c-related api of the ls1088a platform
does not support dm.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add an implementation of the rtc_enable_32khz_output() that uses the
driver model i2c APIs.
Also put code related to rtc_enable_32khz_output
under CONFIG_RTC_ENABLE_32KHZ_OUTPUT.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM
I2C API when DM_I2C is used.When DM_I2C_COMPAT is not enabled for
compilation, a compilation error will be generated. This patch
solves the problem that the i2c-related api of the ls2088a platform
does not support dm.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM
I2C API when DM_I2C is used.When DM_I2C_COMPAT is not enabled for
compilation, a compilation error will be generated. This patch
solves the problem that the i2c-related api of the ls1028a platform
does not support dm.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM I2C
API when DM_I2C is used. When DM_I2C_COMPAT is not enabled for
compilation, a compilation error will be generated. This patch solves
the problem that the i2c-related api of the lx2160a platform does not
support dm.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This driver needs modification to work with new soc,
like ls1028, since bitmap of RCFG is changed to
RESV[7:5] LIVE[4] WDEN[3] RESV[2:1] GO[0]
000 1 0 00 0
Also the RCW location is moved to only dutcfg0.
RESV[7:4] RCWSRC[3:0]
1111 configurable
Following commands are functional now
qixis_reset
qixis_reset sd
qixis_reset qspi
qixis_reset emmc
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
MC firmware need to be aligned to 512M, so minimum 512MB DDR is reserved.
But MC support to work with 128MB or 256MB DDR memory also, in this
case, rest of the memory is not usable.
So reporting this extra memory to Linux through dtb memory fixup.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The Kconfig file calls to ti/common/Kconfig twice which makes
several of the menu items repeat themselves. In an effort to
clean this up, this patch removes the second call which eliminates
the duplicate menu items.
Signed-off-by: Adam Ford <aford173@gmail.com>
Sorry for the noise, but there appears to be a regression with older
hardware. Since it broke the direct_nor boot option, it should be
reverted until a better solution is available.
This reverts commit 51cd1e2373.
The full path has changed in the recent kernels so that it is
not possible to load them. Aliases "ethernet0" and "ethernet1"
are still present in both legacy and new kernels.
Also, fix error messages to correspond to the taken actions.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Historically there have been various boot options, SPI flash,
NAND or NOR. The NOR flash is mutually exclusive with MMC, but
it isn't mutually exclusive with NAND or SPI Flash, so this patch
enables both NAND flash and SPI Flash when booting from NOR.
Signed-off-by: Adam Ford <aford173@gmail.com>
This commit adds support for the B&R brsmarc1 SoM.
The SoM is based on TI's AM335x SoC.
Mainly vxWorks 6.9.4.x is running on the board,
doing some PLC stuff on various carrier boards.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
The SPL for the Overo board does not initialise the MMC. Hence, it
cannot load the main boot loader from the SD card susequently. This
patch moves the initialisation code for the MMC so it gets included in
the SPL.
[trini: Add missing header]
Signed-off-by: Tom Rini <trini@konsulko.com>
The SEI510 board is based on the Amlogic S905X2 SoC
from the Amlogic G12A SoC family.
The board has the following specifications :
- Amlogic S905X2 ARM Cortex-A53 quad-core SoC
- XGB DDR4 SDRAM
- 10/100 Ethernet (Internal PHY)
- 1 x USB 3.0 Host
- eMMC
- SDcard
- Infrared receiver
- SDIO WiFi Module
The board default behaviour is for booting Android and triggers
fastboot on recovery or reboot mode.
USB vendor ID (used by fastboot) is 0x18d1 (Google) for
default udev rules for existing android users work out of the box.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This board is unmaintained and can be removed. This also allows us to
remove kmp204x-common.h and integrate it in kmp204x.h.
Signed-off-by: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Remove the PORTL2 board and all its dependencies as it is no longer
supported by the company.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Activate the driver model for the Ethernet interface (RGMII) in the KM
Kirkwood Kconfig file. Additionally, raise the auto negotiation timeout
to eight seconds as more time is required for those boards.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Activate the driver model for the serial interface in the KM Kirkwood
Kconfig file. The associated preprocessor definitions could be removed
from the header file. However, the clock of 200 MHz needs to be declared
in the device tree.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
After moving the KM specific configurations to Kconfig, the associated
preprocessor definitions can now be removed in the headers. Moreover, the
whitelist has been adapted correspondingly.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
To execute the conversion away from board specific header files, Kconfig
menus have been implemented for all KM boards and additionally for those
having an ARM architecture.
For the moment, the preprocessor definitions stay in the headers. The
boolean types, however, needed a modification (#define CONFIG_* 1).
The default configuration files of some boards required an update in order
to not change the currently defined values of the configurations.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This file contains lots of internal details about the environment. Most
code can include env.h instead, calling the functions there as needed.
Rename this file and add a comment at the top to indicate its internal
nature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Fixup apalis-tk1.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Move these functions to the new header file and rename set_default_env()
to env_set_default() so that it has a consistent env_ prefix.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Move env_set_hex() over to the new header file along with env_set_addr()
which uses it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
As part of the effort to remove things from common.h, create a new header
for the gzip functions. Move the function declarations to it and add
missing documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This commit adds board support for Hikey960 board from Hisilicon. This
board is one of the Consumer Edition boards of the 96Boards family
powered by Kirin960 SoC.
More information about this board can be found in 96Boards website:
https://www.96boards.org/product/hikey960/
The initial supported/tested devices include:
- Debug serial
- SD
With these support, it's good enough for loading Linux Kernel from SD.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
giedi and deneb are i.MX8X based and have additional data with
WLAN MAC in factoryset container. Enable building for these
boards and adapt factoryset functions to set WLAN MAC and dtb
name in environment.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
For new boards we always enable DM_I2C. Extend factoryset functions
to support EEPROM reading on these boards.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
- Enable SD slot on Intel Edison
- Populate CSRT ACPI table for shared DMA controller on Intel Tangier
- Convert Intel ICH-SPI driver to use new spi-mem ops
- Enable config_distro_bootcmd for QEMU x86
- Support U-Boot as a payload for Intel Slim Bootloader
- Avoid writing temporary asl files into the source tree which fixes the
parallel build issue occasionally seen
Support the V1.2 hardware revision with the following pin muxing
changes:
Ddc_scl_pv4 and ddc_sda_pv5 previously used as Apalis GPIO3 and GPIO4
are now used as DDC pins.
Gen2_i2c_scl_pt5 and gen2_i2c_sda_pt6 previously used as DDC pins are
now used as USB power enable signals.
Usb_vbus_en0_pn4 and usb_vbus_en1_pn5 previously used as USB power
enable signals are now used as GPIO3 and GPIO4.
Additionally a new device tree file tegra124-apalis-v1.2-eval.dtb is
loaded on V1.2 and later modules and resp. USB power enable signals
activated.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
