The choice of the SPL_TEXT_BASE is not really a decision that should be
specified by each board's defconfig, as this setting is actually
dictated by the SoC's memory map and the BootROM behaviour.
To make this obvious and reduce the clutter in the defconfig files,
let's specify the SoC constraints in the Kconfig stanza.
This allows us to remove these lines from the defconfig files again.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
Onc of key blocker for using USB Generic host controller
drivers in Allwinner are CLK and RESET drivers, now these
available for USB usage.
So switch sunxi USB use EHCI and OHCI Generic controllers.
Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD
where it already have USB_EHCI_HCD
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.
Signed-off-by: Tom Rini <trini@konsulko.com>
Convert USB fastboot code to use shared fastboot protocol.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is new System-On-Module platform with universal dimm socket for
easy insertation. The EVB board is designed to be universal with
future modules.
Base features of A20-SOM204 board includes:
* 1GB DDR3 RAM
* AXP209 PMU
* KSZ9031 Gigabit PHY
* AT24C16 EEPROM
* Status LED
* LCD connector
* GPIO connector
There will be variants with the following options:
* Second LAN8710A Megabit PHY
* 16MB SPI Flash memory
* eMMC card
* ATECC508 crypto device
The EVB board has:
* Debug UART
* MicroSD card connector
* USB-OTG connector
* Two USB host
* RTL8723BS WiFi/BT combo
* IrDA transceiver/receiver
* HDMI connector
* VGA connector
* Megabit ethernet transceiver
* Gigabit ethernet transceiver
* SATA connector
* CAN driver
* CSI camera
* MIC and HP connectors
* PCIe x4 connector
* USB3 connector
* Two UEXT connectors
* Two user LEDs
Some of the features are multiplexed and cannot be used the same time:
CAN and Megabit PHY. Others are not usable with A20 SoC: PCIe and USB3.
This patch adds defconfig and dts files for this board. The dts is same
with mainline kernel, except some nodes are removed to make file
compatible with existing dtsi file.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
