The analog sensors on iMX8MM are new, used for 14LPP process. So the
Temperature Sensor Monitoring Unit (TMU) has some change accordingly.
We use version 2 in TMU driver to represent the new TMU, so the one
driver can service for both i.MX8MQ/M.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The driver is ported form Linux Kernel and support driver model.
Users need to provide the tmu node and sensors nodes in DTB.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement the read_rom_hwaddr callback to load MAC address from fuse
for imx8m platforms.
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
imx_get_mac_from_fuse is used to load MAC address from fuse. On imx8mp,
we have two different ENET controllers and both need to call this
function. So decouple its declare from fec driver.
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement the callbacks to get phy mode interface and txclk
rate configuration.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add dwc eqos for imx support.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add RX delay enable support for RTL8211F PHY.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
For dual ethernet controllers, the HW design may connect ETH phys to
one MDIO ports. So two different ethernet drivers have to share MDIO bus.
Since two ethernet drivers are independent, we can't ensure their probe
order.
To resolve this problem, introduce an eth phy generic driver and uclass.
After eth-uclass binds, we search the mdio node and binds the phy node
with the eth-phy-generic driver.
When one eth driver get its phy device, the parent of phy device will
probe prior than phy device. So this ensure the eth driver ownes the
MDIO bus will be probed before using its MDIO.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
If a pad is not owned by current partition we should not set its
pinmux.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add fuse check for fec. If the fuse indicates the module
will not work in the SoC, let's fail the initialization.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add fuse check for USB. If the fuse indicates the module
will not work in the SoC, let's fail the initialization.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add fuse check for I2C. If the fuse indicates the module
will not work in the SoC, let's fail the initialization.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In RGMII mode the 10Mbps link speed is supported only when CPSW2G MAC SL is
configured for External Control ("in band") mode
CPSW_PN_MAC_CONTROL_REG.CTL_EN(18) = 1
Hence update am65_cpsw_update_link() to follow documentation.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
The reset_sata should reset the sata device info and free the
probe_ent memory. Otherwise, it will cause memory leak if we
init the sata again.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix coverity issue CID 43665: Free of address-of expression (BAD_FREE)
incorrect_free: free frees incorrect pointer pp.
pp points the port array field of struct ahci_uc_priv, should not free it.
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix coverity issue CID 3261683: Wrong operator used
(CONSTANT_EXPRESSION_RESULT) operator_confusion:
({...; __v;}) | 67108864 is always 1/true regardless of the values
of its operand. This occurs as the logical operand of !
When DIAG_X is set, the PHY COMINIT signal is detected, so
should use '&' to check whether it is set.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix coverity issue CID 3606684: Resource leak (RESOURCE_LEAK)
leaked_storage: Variable uc_priv going out of scope leaks the storage it points to
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move CONFIG_SYS_MTDPARTS_RUNTIME into Kconfig done by moveconfig.py.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The two functions are now exactly the same, remove one of them.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We can configure the clock output in the device tree. Disable the
hardcoded one in here. This is highly board-specific and should have
never been enabled in the PHY driver.
If bisecting shows that this commit breaks your board it probably
depends on the clock output of your Atheros AR8035 PHY. Please have a
look at doc/device-tree-bindings/net/phy/atheros.txt. You need to set
"clk-out-frequency = <125000000>" because that value was the hardcoded
value until this commit.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support for configuring the CLK_25M pin as well as the RGMII I/O
voltage by the device tree.
By default the AT803x PHYs outputs the 25MHz clock of the XTAL input.
But this output can also be changed by software to other frequencies.
This commit introduces a generic way to configure this output.
Also the PHY supports different RGMII I/O voltages: 1.5V, 1.8V and 2.5V.
An internal LDO is able to provide 1.5V (default) and 1.8V. The 2.5V
option needs an external supply voltage. This commit adds support to
switch the internal LDO to 1.8V.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Provide functions to read and write the Atheros debug registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Debug register 5 contains TX_CLK DELAY at bit 8 and reserved values at
the other bit positions, just like the other PHYs in the family do.
Therefore, it is not necessary to hardcode the reserved values, but
instead simply follow the read-modify-write procedure from the common
function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
To eliminate any doubts about the out-of-reset value of the PHY, that
the driver previously relied on.
If bisecting shows that this commit breaks your board you probably have
a wrong PHY interface mode. You probably want the
PHY_INTERFACE_MODE_RGMII_RXID or PHY_INTERFACE_MODE_RGMII_ID mode.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Also take the opportunity to use the phy_read_mmd and phy_write_mmd
convenience functions.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Delete the extraneous write to debug reg 5 that enables Tx delay
When the driver was originally introduced in commit "6027384a phylib:
Add Atheros AR8035 GETH PHY support", the Tx delay was being
unconditionally enabled.
Then during "2ec4d10b phy: atheros: add support for RGMII_ID, RGMII_TXID
and RGMII_RXID", the author did not notice that code for enabling Tx
delay code was already. Therefore, the if condition for Tx delay has
always been useless for this PHY since this commit introduced it.
Prior to this patch, every AR8035 PHY in U-boot had Tx delay enabled.
After this patch, only those who define the interface as RGMII_TXID or
RGMII_ID will. This is to be expected, but will nonetheless break the
setups of those who didn't know they rely on Tx delay implicitly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Even though the PL011 UART driver claims to be DM compliant, it does not
really a good job with parsing DT nodes. U-Boot seems to adhere to a
non-standard binding, either requiring to have a "skip-init" property in
the node, or to have an extra "clock" property holding the base
*frequency* value for the baud rate generator.
DTs in the U-Boot tree seem to have been hacked to match this
requirement.
The official binding does not mention any of these properties, instead
recommends a standard "clocks" property to point to the baud base clock.
Some boards use simple "fixed-clock" providers, which U-Boot readily
supports, so let's add some simple DM clock code to the PL011 driver to
learn the rate of the first clock, as described by the official binding.
These clock nodes seem to be not ready very early in the boot process,
so provide a fallback value, by re-using the already existing
CONFIG_PL011_CLOCK variable.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[trini: Add <clock_legacy.h> for get_bus_freq() for layerscape
platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In commit f62782fb29 ("cache: l2x0: Fix write to incorrect shared-override
bit") we removed writel to regs->pl310_aux_ctrl by accident. This
commit restores it back.
Fixes: f62782fb29 ("cache: l2x0: Fix write to incorrect shared-override bit")
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
- Add DM model for P1010RDB
- Add I2C DM Model support for P1010RDB, T1042RDB, T2080, T4240RDB,
MPC8548CDS, T1024RDB, P4080, P3041DS, P2041RDB, P2020RDB, P1020RDB,
P5040DS
- Fix reference to READM.qe_firmware
Commit 69529c9120 ("net: pcnet: Switch to PCI memory access")
switched from PCI IO access to PCI memory access without updating
the I/O primitives. Contrary to SH, the primitives for memory
access and IO access are implemented differently. Thus doing
memory access with IO port primitives breaks the driver on
MIPS Malta board.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
- dts clean up to use -u-boot for px30, rk3399 boards
- dts sycn from upstream kernel for rk3328, rk3399
- add rockchip rng driver
- new board support: rk3328-roc-cc, rk3399-roc-pc,Nanopi M4 2GB
This is part 1 of big network cleanup / DM conversion.
The dc2114x/rtl8139/pcnet/tulip PCI adapter drivers received checkpatch
cleanups in preparation for DM conversion. The smc911x is converted to
DM completely. The dwc_eth_qos cache fixes are applied.
In two files README.qe_firmware is referenced which never made it into the
U-Boot tree. The README is available in the Linux kernel tree.
Update the references.
Cc: Timur Tabi <timur@kernel.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add REVC informaiton.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
iMX8QM registers two thermal devices for CPUs, get the temperature
from "cpu-thermal1" device for A72
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When current cpu is A53, using is_cortex_a53 could not detect A72
information, so check cpu device compatible property to get
the correct information.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Return 4 is not correct on i.MX8DX/DXL/8QM and etc. we need to count
available cpu node with device_type "cpu".
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When running on SoC with multiple clusters, the boot CPU may
not be fixed, saying booting from cluster A or cluster B.
Add a API that can return the udevice for current boot CPU.
Cpu driver needs to implement is_current_cpu interface for this
feature, otherwise the API only returns the first udevice in
cpu uclass.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
If SDP_WRITE and SDP_JUMP addr is zero, use CONFIG_SDP_LOADADDR
as default address
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch is used to support the on-chip xHCI controller on
MediaTek SoCs, currently control/bulk/interrupt transfers are
supported.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Usually the digital and analog phys use the same reference clock,
but some platforms have two separate reference clocks for each of
them, so add another optional clock to support them.
In order to keep the clock names consistent with PHY IP's, change
the da_ref for analog phy and ref clock for digital phy.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
The new version removes all shared banks between multi-phys
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Support USB2 and USB3 PHY with shared banks when support multi-phys
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Use the phy bulk API to get a group of phys
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Get a group of phys by the phy bulk API
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds a "bulk" API to the phy API in order to
get/init/exit/power on/off a group of phys associated
with a device.
The bulk API will avoid adding a copy of the same code to
manage a group of phys in drivers.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This patch add function used to get the child count of
a ofnode or a device
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
LCDIF clock gate was wrong so set it according to RM.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The timers compatible string in upstream is called
mt6577-timer. Add this compatible to the driver.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
As noted in rtc_def.h, the tm_mon field in struct rtc_time is 1-12,
unlike in struct tm where it is 0-11. Currently, running "date" prints
the wrong
Date: 2020-04-01 (Friday) Time: 13:05:30
and setting the RTC via the date command is also broken.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Add support for U-Boot DM and DT probing. Furthermore, build the
SMC911x standalone EEPROM example only for the non-DM case, as it
is not converted yet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch enables the possibility to set FEC_ENET_ENABLE_TXC_DELAY or
FEC_ENET_ENABLE_RXC_DELAY so one can via a define enable the RXC or TXC
delay in the MAC.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Add a module to configure the tamper and secure violation of
the SNVS using the SCU API.
The module also adds some commands:
- snvs_cfg: Configure the SNVS HP and LP registers
- snvs_dgo_cfg: Configure the SNVS DGO bloc if present (8QXP)
- tamper_pin_cfg: Change the configuration of the tamper pins
- snvs_clear_status: Allow to write to LPSR and LPTDSR to clear
status bits
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sync the latest SCFW API with below commit
6dcd0242ae7a53ac ("SCF-105: Revert accidental change") to add
interfaces for PM resource reset and read/write SNVS security
violation and tamper DGO registers.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Split network handling functions into non-DM specific parts and
common code in preparation for conversion to DM.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Invert the status handling logic in smc911x_recv(), to make the
function easier to read, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Introduce a private data structure for this driver with embedded
struct eth_device and pass it around. This prepares the driver to
work with both DM and non-DM systems.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Convert the IO accessors to standard ones instead of using volatile
void pointers, as those do not cover all the bus access details.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
These accessors are not overridden by any board, and even if they were,
this is something which should be handled via DM now, so remove the
weak alias option. Moreover, drop the inline keyword, as the compiler
can decide better.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Inline all the functions from the header file, as they are not used
outside of the driver or the standalone EEPROM example.
Note that this does introduce considerable amount of duplication in
the standalone EEPROM example, however that one has to be rewritten
anyway, roughly such that the SMC911x driver would expose DM EEPROM
interface and the standalone example would use that.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Pull the MII interface registration into separate function to avoid the
ifdeffery in smc911x_initialize(). Moreover, adjust the fail path such
that we use goto labels.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Fix memleak in the init fail path, where if allocation or registration
of MDIO bus fails, then ethernet interface is not unregistered and the
private data are not freed, yet the probe function reports a failure.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Invert the logic in the aforementioned functions to reduce indent,
no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Rename the function to keep the naming scheme consistent,
no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Replace combination of malloc()+memset() with calloc() as the behavior
is exactly the same and the amount of code is reduced.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
These functions are never used and are likely a pre-DM remnant
from times long past, just remove them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The rtl8139 driver is derived from Etherboot driver, which is in
turn derived from Linux 8139too driver added in Linux 2.2.18pre14.
An undocumented change in Linux 2.4.10.2 added a new field to the
driver, MODULE_LICENSE("GPL"); . According to current Linux kernel
licensing rules, Documentation/process/license-rules.rst, quote:
"GPL" Module is licensed under GPL version 2. This
does not express any distinction between
GPL-2.0-only or GPL-2.0-or-later. The exact
license information can only be determined
via the license information in the
corresponding source files.
And since the code does not contain any "future" clause, the tag
is therefore GPL-2.0 only.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Just move functions around in preparation for easy DM conversion,
rename rtl_bcast_addr() to rtl8139_bcast_addr(), no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Finish the checkpatch cleanup of the driver, fix the remaining issues
in probe and init function and in global variables, rename the probe
function to rtl8139_init(), no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
This hardware reset and reset-wait implementation was twice in the
driver, factor it out into a separate function. This really should
use wait_for_bit() eventually and return -ETIMEDOUT, but thus far,
handling of any of this is missing from the driver. This must be
added later. Thus far, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_stop(), clean up checkpatch errors in
the stop polling function. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_recv(), clean up various checkpatch errors,
line-over-80 conditions, and malformed comments. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_send(), clean up the TX polling, the TX
OK condition at the end, overuse of typecasts, and various line-over-80
problems. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_reset(), clean up the reset polling
and various line-over-80 problems. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_set_rx_mode(), use unsigned variables
where applicable and inline mc_filter[] values. No functional chanage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
This string of macros is exactly the same thing as rtl8139_rx_config,
so just use rtl8139_rx_config. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_read_eeprom() to keep the naming
consistent, keep the variables sorted in reverse xmas tree. No
functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The macro assumes ee_addr variable to be present when it's being
used. Rework the macro into a function instead and pass it an
argument specifying the register base address, to make it future
proof for DM conversion.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the horrible register definitions in the RTL8139 driver.
This does create a couple of checkpatch errors, but the driver is
full of them anyway, and those will be cleaned up later.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The DMA may attempt to write a DMA descriptor in the ring while it is
being updated. By writing the DMA descriptor buffer address to 0, it
is assured the DMA will not use such a buffer and the buffer can be
updated without any interference.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
This patch prevents an issue where the RX packet might have been
accessed by the CPU, which now has cached data from the packet in
the caches and possibly various write buffers, and these data may
be evicted from the caches into the DRAM while the buffer is also
written by the DMA.
By invalidating the buffer after the CPU accessed it and before the
DMA populates the buffer, it is assured that the buffer will not be
corrupted.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
The current code polls the RX desciptor ring for new packets by reading
the RX descriptor status. This works by accident, as the RX descriptors
are often in non-cacheable memory. However, the driver does support use
of RX descriptors in cacheable memory.
This patch adds a missing RX descriptor invalidation, which assures the
CPU will read a fresh copy of the RX descriptor instead of a cached one.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Currently the code only flushes the first RX descriptor, not every entry
in the RX descriptor ring. Fix this, to make sure the DMA engine can pick
the RX descriptors correctly.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
This code programs the next descriptor in the TX descriptor ring into
the hardware as the last valid TX descriptor. The problem is that if
the currenty descriptor is the last one in the array, the code will
not wrap around correctly and use TX descriptor 0 again, but instead
will use TX descriptor at address right past the TX descriptor ring,
which is the first descriptor in the RX ring.
Fix this by adding the necessary wrap-around.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
The RX descriptor field 3 should contain only OWN and BUF1V bits before
being used for receiving data by the DMA engine. However, right now, if
the descriptor was already used for receiving data and is being cleared,
the field 3 is only modified and the aforementioned two bits are ORRed
into the field. This could lead to a residual dirty bits being left in
the field 3 from previous transfer, and it generally does. Fully set the
field 3 instead to clear those residual dirty bits.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Replace the adhoc debugging ifdeffery with debug_cond() and an
internal SROM_DEBUG macro to select the debug level.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Move the functions in the driver around to better fit future DM
conversion, drop function forward declarations. No functional
change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename these functions to dc2114x_{inl,outl}(), use u32 values in
them instead of plain signed integers as all those values are in
fact register values and the driver code does bitwise operations
on them. No functional change intended.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace these macros with static functions to permit the compiler to
do type checking on the functions. The INL()/OUTL() functions have to
be moved in this patch as well, as those DE4X5 macros are using them.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the remaining driver code, macro space alignment, function
declaration indent, replace __attribute__((aligned(32))) with plain
__aligned(32). No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the SROM accessors to bring them up to standards with
U-Boot coding style. Sort variable into reverse xmas tree. No
functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the send_setup_frame() to bring it up to standards with
U-Boot coding style, invert the loops where applicable to cut
down the level of indent. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the driver halt code to bring it up to standards with
U-Boot coding style. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the driver recv code to bring it up to standards with
U-Boot coding style. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the driver send code to bring it up to standards with
U-Boot coding style, invert the loops where applicable to cut
down the level of indent. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the driver init code to bring it up to standards with
U-Boot coding style, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace the PCI IO access with PCI memory access, the card
supports both, but the former does not work with QEMU SH4.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace mips-specific UNCACHED_SDRAM() macro with standard
map_physmem(), which permits the driver to work on other
systems than mips.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
These macros are not used by any board, remove them to simplify
the driver. The EEPROM accessors are still retained however, as
those might still be useful.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
These macros guard one switch-case statement, which grows mips malta
by some 20 bytes if debug is enabled, and even less if it is not. To
make the code simpler, just support all the NICs and be done with it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Due to v5.7-rc1 sync the SD controller nodes in rk3399.dtsi
have HCLK_SD assigned-clocks which are usually required for
Linux and don't require to handle them in U-Boot.
assigned-clocks = <&cru HCLK_SD>;
So, mark them as empty in clock otherwise device probe on
those SD controllers would fail.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The guessed reason is that the existing logic of filling
tx fifo with data, rx fifo with NULL for tx transfer and
filling rx fifo with data, tx fifo with NULL for rx transfer
is not clear enough to support the Quad Page Program.
SiFive SPI controllers have specific sets of watermark
registers and SPI I/O directions bits in order to program
SPI controllers clear enough to support all sets of operating
modes.
Here is the exact programing sequence that would follow on this
patch and tested via SPI-NOR and MMC_SPI.
- set the frame format proto, endian
- set the frame format dir, set it for tx and clear it for rx
- TX transfer:
fill tx fifo with data.
wait for TX watermark bit to clear.
- RX transfer:
fill tx fifo with 0xff.
write nbytes to rx watermark register
wait for rx watermark bit to clear.
read the rx fifo data.
So, this patch adopts this program sequence and fixes the existing
I/O direction bit.
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Sagar Kadam <sagar.kadam@sifive.com>
SiFive SPI controller has a proto bit field in frame format
register which would be used to configure the SPI I/O protocol
lines used on specific transfer.
Right now the driver is configuring this proto using slave->mode,
for all types of transctions. This makes the driver unable to
function since the proto needs to configure dynamically for
each and every transaction separately at runtime.
Now, the controller driver supports per transfer via spi-mem
exec_opo, so add the fmt_proto flag and fill the per transfer
buswidth so that the controller configures the proto bit at
runtime.
This patch fixes the SPI controller works with SPI NOR flash
on quad read with page program.
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Sagar Kadam <sagar.kadam@sifive.com>
SiFive SPI controller is responsible to handle the
slave devices like mmc spi and spi nor flash.
The controller is designed such a way that it would
handle the slave transactions based on the I/O protocol
numbers, example if spi nor slave send quad write opcode
it has to send alone with I/O protocol number of 4 and
if it try to send data it has to send I/O protocol number
along with 4 line data.
But the current spi-xfer code from spi-mem is combining
the opcode and address in a single transaction, so the
SPI controller will be unable to identify the I/O protocol
number of opcode vs address.
So, add the spi-mem exec_op with spi-xfer of opcode, address
and data as a separate transaction. This doesn't remove
the .xfer of dm_spi_ops since mmc spi will make use of it.
Note: This code might have moved to the spi-mem core area
once we have done the dedicated tests on other controllers
and have real reason to move.
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Sagar Kadam <sagar.kadam@sifive.com>
Spansion "s25fs512s" flash is incorrectly decoded as "s25fl512s" on
various platforms as former is not present. Add the entry.
Linux already has both the flashes present. A snippet below:
{ "s25fl512s", INFO6(0x010220, 0x4d0080, 256 * 1024, 256...},
{ "s25fs512s", INFO6(0x010220, 0x4d0081, 256 * 1024, 256...},
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Enable designware watchdog driver for rk3399 if WDT defined.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
IS25WP256 flash chips do support 4byte address opcodes,
so enable support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Sagar Kadam <sagar.kadam@sifive.com>
Enable QE bit for ISSI flash chips.
QE enablement logic is similar to what Macronix
has, so reuse the existing code itself.
Cc: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Usually variable name slave is used for spi_slave structure
and slave_plat for the dm_spi_slave_platdata.
Let's follow this meaningful notation by replacing slave
with slave_plat for dm_spi_slave_platdata structure.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Add DM_ETH support for DPAA1, DPAA2 based RDB platforms: ls1046ardb,
ls1043ardb, lx2160ardb, ls2088ardb, ls1088ardb.
- Add GICv3 support for ls1028a, ls2088a, ls1088a.
- Add lpuart support on ls1028aqds.
- Few bug fixes and updates on ls2088a, ls1012a, ls1046a, ls1021a based
platforms.
When U-Boot is not the first-stage bootloader we don't want to
re-configure the PCI devices, since this has already been done. Add a
check to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
A device may want to write out ACPI tables to describe itself to Linux.
Add a method to permit this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Probe the FMan MACs based on the device tree while
retaining the legacy code/functionality.
One notable change introduced here is that, for DM_ETH,
the name of the interfaces is corrected to the fmX-macY
format, that avoids the referral to the MAC block names
which were incorrect for FMan v3 devices (i.e. DTSEC,
TGEC) and had weird formatting (i.e. FM1@DTSEC6, FM1@TGEC1).
The legacy code is left unchanged in this respect.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Allow the MDIO devices to be probed based on the device tree.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move the receive buffer free code in a separate function.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Make any adjustments necessary in order to support DPAA2 devices probed
using CONFIG_DM_ETH. While at it, fixup some styling issues aroung the
switch-case statement.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When CONFIG_DM_ETH is enabled DPAA2 network interfaces will now probe
based on DTS nodes with the "fsl,qoriq-mc-dpmac" compatible.
In this case, transform the ldpaa_eth driver into a UCLASS_ETH driver
and reuse the _open()/_tx()/_stop() functions already inplemented.
For the moment, the ldpaa_eth driver will support both configurations:
with or without CONFIG_DM_ETH enabled. Any 'struct eth_device' occurrence
now has a matching 'struct udevice' made mutually exclusive based on the
state of CONFIG_DM_ETH.
Signed-off-by: Florin Laurentiu Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add a driver for the MDIO interface integrated in the mEMAC (Multi-rate
Ethernet Media Access Controller) and the Fman 10G Ethernet MACs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add a driver for the rng device found on rockchip platforms.
Support rng module of crypto v1 and crypto v2.
Signed-off-by: Lin Jinhan <troy.lin@rock-chips.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit: 0ebb261a0b2d ("spi: spi-mem: Add SPI_MEM_NO_DATA to the spi_mem_data_dir enum")
in linux.
When defining spi_mem_op templates we don't necessarily know the size
that will be passed when the template is actually used, and basing the
supports_op() check on op->data.nbytes to know whether there will be
data transferred for a specific operation is not possible.
Add SPI_MEM_NO_DATA to the spi_mem_data_dir enum so that we can base
our checks on op->data.dir instead of op->data.nbytes.
This also fixes a bug identified with the atmel-quaspi driver.
The spi-nor core, when erasing sectors, fills the spi_mem_op template
using SPI_MEM_OP_NO_DATA, which initializes all the data members with
value zero. This is wrong because data.dir is treated as SPI_MEM_DATA_IN,
which translates in our driver to read accesses for erases (RICR), while
the controller expects write accesses (WICR).
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Toshiba recently launched new revisions of their serial SLC NAND series.
TC58CVG2S0HRAIJ is a refresh of previous series with minor improvements.
Basic parameters are same so lets add support for this new revision.
Datasheet: https://business.kioxia.com/info/docget.jsp?did=58601&prodName=TC58CVG2S0HRAIJ
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Linux has good support for Toshiba SPI-NAND, so lets import it.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The s25fl256s0 supports dual and quad read like s25fl256s1.
Enable it by adding SPI_NOR_DUAL_READ and SPI_NOR_QUAD_READ
flags to the flash_info entry.
Tested on real silicon and confirmed to be working.
Signed-off-by: Bacem Daassi <Bacem.Daassi@cypress.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
"assigned-clock-parents" and "assigned-clock-rates" DT properties take
effect only after ofdata_to_platdata() when clk_set_defaults() is called
in device_probe(). Therefore clk get rate() would return a wrong value
in ofdata_to_platdata() when compared with probe. Hence it needs to be
moved to probe.
Tested on u-boot-ti/next.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
hweight32 is a somewhat expensive way to check for power-of-2. Use the
is_power_of_2 helper, which does the standard and cheap idiom
foo&(foo-1)==0.
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-96 (-96)
Function old new delta
spi_nor_write 388 292 -96
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
To support the SPI MEM API, instead of modifying the existing U-Boot
driver, this patch adds a port of the existing Linux driver.
This also has the advantage that porting changes and fixes from Linux will
be easier.
Porting of driver left most of the functions unchanged while few of the
changes are:
-Remove lock(mutexes) and irq handler as u-boot is a single core execution.
-Remove invalid masterid as it was required specially for multicore
execution in LS2088ARDB which is not the case in u-boot.
-Remove clock support as changing spi speed is not supported in uboot and
nor in linux.
Currently tested on LS1088ARDB, LS1012ARDB, LS1046ARDB, LS1046AFRWY,
LS1043AQDS, LS1021ATWR, LS2088ARDB, I.MX6ULL EVK.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
- add GXBB USB PHY driver
- enable access to SPI NOR Flash on VIM2 and VIM3/VIM3L boards
- fix USB PHYs Power-Up on on VIM3/VIM3L boards
-----BEGIN PGP SIGNATURE-----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=e10O
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200428' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- fix sd-emmc controller A init on G12A/G12B/SM1 SoCs
- add GXBB USB PHY driver
- enable access to SPI NOR Flash on VIM2 and VIM3/VIM3L boards
- fix USB PHYs Power-Up on on VIM3/VIM3L boards
dwc3-sti-glue has been broken since MISC uclass has been
modified to scan DT sub-nodes after bind.
Fixing it by a using the no-op uclass.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Solve issue for the display of "usb start" command on stm32mp1
because one carriage return is missing in DWC2 probe.
Before the patch:
STM32MP> usb start
starting USB...
Bus usb-otg@49000000: Bus usbh-ehci@5800d000: USB EHCI 1.00
after the patch:
STM32MP> usb start
starting USB...
Bus usb-otg@49000000: USB DWC2
Bus usbh-ehci@5800d000: USB EHCI 1.00
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Assert reset before deassert in dwc2_reset;
this patch solve issues when the DWC2 registers are already
initialized with value incompatible with host mode.
Force a hardware reset of the IP reset all the DWC2 registers at
default value, the host driver start with a clean state
(Core Soft reset doen in dwc_otg_core_reset is not enought
to reset all register).
The error can occurs in U-Boot when DWC2 device gadget driver
force device mode (called by ums or dfu command, before to execute
the usb start command).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support for clock with driver model.
This patch don't added dependency because when CONFIG_CLK
is not activated the clk function are stubbed.
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Use generic phy to initialize the PHY associated to the
DWC2 device and available in the device tree.
This patch don't added dependency because when CONFIG_PHY
is not activated, the generic PHY function are stubbed.
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use ofnode_decode_display_timing() instead of
fdtdec_decode_display_timing() to parse display timing, so that we can
support live DT.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Power on/off the PHYs to enable power to the USB ports, fixing USB support
on Khadas VIM3/VIM3L boards.
The G12A USB complex has at least 2 USB2 PHYs, but one is muxed between the
DWC2 and DWC3 controller and the other one directly connected to the DWC3
controller. The USB3+PCIe combo PHY is muxed between the DWC3 controller
and a DW-PCIE controller.
All PHYs are optional, but it's type (usb2/usb3) and position are important
to determine it's capabilities, thus they are stored in a fixed size
array and the phy-name determines it's position, it's position determining
it's type and functionnalities.
This is why we need to loop over the array to power on all the DT provided
PHYs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This adds support for the USB PHY found on Amlogic GXBB SoCs.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add missing SD_EMMC_A controller gates needed for probe of the A
controller, otherwise leading to a freeze of the SoC after b3d69aa596.
Fixes: b3d69aa596 ("clk: meson: reset mmc clock on probe")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
- bmips: fix build error when disabling USB
- mips: add option to restore original exception vector base
- mips: fix off-by-one error when clearing gd_data
- mips: minor fixes for compatibility with generic SPL framework
- spl: refactor legacy image loading
- spl: add LZMA decompression support for legacy images
- Makefile: add target to build LZMA compressed U-Boot images
- mtmips: refactor and rewrite low-level init code
- mtmips: add and enable SPL support with LZMA
- mtmips: add support for MT7628 reference board
- mtmips: add support for VoCore/VoCore2 board
-----BEGIN PGP SIGNATURE-----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=2jL1
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2020-04-27' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips
- brcmnand: fix missing code path from Linux driver
- bmips: fix build error when disabling USB
- mips: add option to restore original exception vector base
- mips: fix off-by-one error when clearing gd_data
- mips: minor fixes for compatibility with generic SPL framework
- spl: refactor legacy image loading
- spl: add LZMA decompression support for legacy images
- Makefile: add target to build LZMA compressed U-Boot images
- mtmips: refactor and rewrite low-level init code
- mtmips: add and enable SPL support with LZMA
- mtmips: add support for MT7628 reference board
- mtmips: add support for VoCore/VoCore2 board
Here we introduce new development platfrom for ARC: HSDK 4xD.
That's pretty much the same base-board as in HSDK but with
very recent quad-core ARC HS47D in the ASIC.
Thus we try to re-use existing code as much as possible while
inevitably add some pieces needed for the new ASIC.
Also we drop selection of bounce buffers on AXS10x
as there's no use of them any longer.
Some chips provide their sysreset function in reset controller, which is
normally a bit written to 1 to perform the sysreset.
This patch adds a new sysreset driver to take advantage of it.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Linux Broadcom NAND driver only disabled clock if no childs are initialized.
This section of the code seems to have been accidentally dropped when it was
imported in U-Boot.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The end_cmd field in the variables cmd_phase_addr and data_phase_addr
contains the value 0xFF when the end_cmd equals NAND_CMD_NONE. This
should be 0x00.
This is caused by comparing NAND_CMD_NONE (int) with end_cmd (u8).
end_cmd will be promoted by the int value -1 and therefore is not equal
to 0xFF. Solved by casting NAND_CMD_NONE to u8 which will avoid int
promotion.
Signed-off-by: Patrick van Gelder <patrick.vangelder@nl.bosch.com>
Reviewed-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable mux based clocks to populate LPD_LSBUS clock to xilinx_wwdt
driver. Skip reading clock rate for the mux based clocks with
parent clock id is zero.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Currently, the entry "bus-width = <8>" in the ZynqMP's sdhci nodes
is not evaluated. This results in the bus width staying at its default
value (4 bit in HS200 mode).
Fix this by calling mmc_of_parse. This function also checks for the
"no-1-8-v" and "max-frequency" entries. Remove the handling of those
nodes from this driver.
Signed-off-by: Benedikt Grassl <Benedikt.Grassl@rohde-schwarz.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for additional timer clock which belongs to tunnel
domain.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
The rk_edp.c and rk_lvds.c files reference rk_setreg which is declared in
hardware.h so include it so the drivers build. Adjust rk_lvds.c so
includes are in alphabetical order while updating.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
The build currently fails with
drivers/spi/mpc8xxx_spi.c:64:3: warning: implicit declaration of function ‘dev_err’ [-Wimplicit-function-declaration]
...
drivers/spi/built-in.o: In function `mpc8xxx_spi_set_speed':
drivers/spi/mpc8xxx_spi.c:227: undefined reference to `dev_err'
Fixes: 4856cc7a97 (mpc8xxx_spi: implement real ->set_speed)
Fixes: 1a7b462dee (mpc8xxx_spi: put max_cs to use)
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
This patch converts S900 clock driver to something common that can
be used for other SoCs, for instance S700(few of clk registers are same).
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Synchronize device tree bindings with v5.5-rc6 tag with commit id
"b3a987b0264d".
Also, it removes older clock binding defined for S900 along with undocumented
compatible string "actions,s900-serial" from serial driver and adapts clock
driver to cater to new bindings.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This patch adds "actions,owl-uart" string to the owl uart driver. It
is also defined in Linux kernel.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This function does not modify the device to change it to use const *, so
that callers with a const udevice * can call it without a cast.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Commit 6293b0361d ("mtd: nand: pxa3xx: add raw read support") added the
local data_len variable in handle_data_pio() to track read size, but
forgot to update the condition of drain_fifo() call. That happens to
work when the layout last_chunk_size != 0. But when last_chunk_size ==
0, drain_fifo() is not called to read the last chunk, which leads to
"Wait timeout!!!" error. Fix this.
Fixes: 6293b0361d ("mtd: nand: pxa3xx: add raw read support")
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
After a successful upgrade, multiple problem during boot sequence may
trigger the altbootcmd process.
This patch adds a version and an upgrade_available entries to the
bootcount file to enable/disable the bootcount check.
When failing to read the bootcount file it will consider that bootcount is
enabled, acting as previously, and update the file accordingly.
The bootcount file is only saved when `upgrade_available` is true, this
allows to save writes to the filesystem.
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
mt7531 is a 7-ports switch with 5 embedded giga phys, and uses the same
MAC design of mt7530. The cpu port6 supports SGMII only. The cpu port5
supports RGMII or SGMII in different model.
mt7531 is connected to mt7622 via both RGMII and SGMII interfaces.
In this patch, mt7531 cpu port5 or port6 is configured to maximum
capability to align CPU MAC setting.
The dts has been committed in the commit 6efa450565 ("arm: dts:
mediatek: add ethernet and sgmii dts node for mt7622")
Signed-off-by: Landen Chao <landen.chao@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
The mpc8xx watchdog can work either in 'reset mode' or 'NMI mode'.
The selection can be done at startup only.
It is desirable to select the mode without rebuilding U-boot.
It is also desirable to disable the watchdog without rebuilding.
At watchdog startup, check environment variable 'watchdog_mode'.
If it is 'off', the watchdog is not started. If it is 'nmi',
the watchdog is started in NMI mode. Otherwise, it is started
in reset mode which is the default mode.
Signed-off-by: Charles Frey <charles.frey@c-s.fr>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
commit 719cab6d2e ("dm: pinctrl: convert pinctrl-single to livetree")
converted pinctrl driver to livetree. In this conversion, the call to
read pinctrl-single,pins/bits property is provided with pinctrl device
pointer instead of pinctrl config pointer. Because of this none of the
pins gets configured. Fix it by passing the right udevice pointer.
Fixes: 719cab6d2e ("dm: pinctrl: convert pinctrl-single to livetree")
Reported-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
- iproc_sdhci memory leak fix and enable R1B resp quirk
- more mmc cmds and several mmc updates from Heinirich
- Use bounce buffer for tmio sdhci
- Alignment check for tmio sdhci
RPMB support is used by the 'mmc rpmb' command and by the OP-TEE support.
We do not need it in SPL.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Implement get_b_max() for the Renesas R-Car SDHI controller driver, limit
the b_max per hardware capabilities such that select Gen2 controllers have
16bit block transfer limit, the rest has 32bit block transfer limit and on
Gen3, the block transfer limit on addresses above the 32bit boundary is set
to 1/4 of the malloc area.
Originally, on Gen3, the block transfers above the 32bit area were limited
to PIO only, which resulted in (R8A7795 Salvator-X , HS200 eMMC):
=> time mmc read 0x0000000700000000 0 0x10000
time: 0.151 seconds
=> time mmc read 0x0000000700000000 0 0x100000
time: 11.090 seconds
with bounce buffer in place and b_max adjustment in place:
=> time mmc read 0x0000000700000000 0 0x10000
time: 0.156 seconds
=> time mmc read 0x0000000700000000 0 0x100000
time: 2.349 seconds
Note that the bounce buffer does mallocate and free the bounce buffer
for every transfer. Experiment which removes this results in further
increase of read speed, from 2.349s to 2.156s per 512 MiB of data,
which is not such a significant improvement anymore. It might however
be interesting to have bounce buffer directly in the MMC core or even
block core.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Add getter function which permits adjusting the maximum number of
blocks that could be read in a single sustained read transfer based
on the location of the source/target buffer and length, before such
transfer starts.
This is mainly useful on systems which have various DMA restrictions
for different memory locations, e.g. DMA limited to 32bit addresses,
and where a bounce buffer is used to work around such restrictions.
Since the U-Boot bounce buffer is mallocated, it's size is limited
by the malloc area size, and the read transfer to such a buffer must
also be limited. However, as not all areas are limited equally, the
b_max should be adjusted accordinly as needed to avoid degrading
performance unnecessarily.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
The R-Car SDHI DMA controller has various restrictions. To work around
those restrictions without falling back to PIO, implement bounce buffer
with custom alignment check function which tests for those limitations.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
set_ios_post return type changed from void to int, correcting
the same to fix compilation warning.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Provide command 'mmc wp' to power on write protect boot areas on eMMC
devices.
The B_PWR_WP_EN bit in the extended CSD register BOOT_WP is set. The boot
area are write protected until the next power cycle occurs.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Register value table for DDR PHY clock divider are wrong. They should be
0 or 1 for divide-by-2 or divide-by-4, respectively. Not 1 or 2. Current
values do not make sense, since 2 cannot be achieved, because the
register is only 1 bit long (mask is set to 1).
This fixes clk dump reporting DDR PHY clock rate differently from Linux.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
In R-Car Gen 3, there is a DMA controller restriction of SDHI.
When the transfer exceeding the 4 kByte boundary is performed while
the DRAM address is not 128 byte aligned, the bus is occupied.
This patch avoids this.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
- Further cleanups for 'make refcheckdocs'
- Another BTRFS fix.
- Support for automatic decompression of images with booti as well as
unlz4 command for manual decompression.
- fix SMBIOS info on Odroid-C2
- Fix video output on GXBB/GXL/GXM boards
- add USB gadget support for GXL/GXM boards
-----BEGIN PGP SIGNATURE-----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=1Ffl
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200420' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- enable DM_RNG on meson boards
- fix SMBIOS info on Odroid-C2
- Fix video output on GXBB/GXL/GXM boards
- add USB gadget support for GXL/GXM boards
Add set_mode function in the Amlogic GXL PHYs that will be called by
the arch code to switch PHYs from/to gadget mode.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add generic_phy_get_by_node() to get a PHY phandle from a node instead
of a udevice.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[narmstrong: fixed by including ofnode.h in generic-phy.h]
This adds the PCA9546 4-channel i2c bus switch.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Heiko Schocher <hs@denx.de>
In some cases U-Boot runs the same binary on different board versions.
In wandboard, for example, there are versions with the PFUZE100 PMIC
populated and others without it.
When the PMIC is not present, it is not really useful to get PMIC error,
so change the error message level to debug instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Heiko Schocher <hs@denx.de>
ENABLE signal can now be flipped by writing its bitmask on vdctrl0
register.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
DOTCLK signal can now be flipped by writing its bitmask on vdctrl0
register.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
VSYNC signal can now be flipped by writing its bitmask on vdctrl0
register.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
HSYNC signal can now be flipped according to display_flags bitmaks by
writing its bitmask on vdctrl0 register.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
struct display_timings provides more informations such clock and DE
polarity, so let's refactor the code to use struct display_timings
instead of struct ctfb_res_modes, so we'll become able to get clock and
DE polarity settings and set register according to them in the next patch.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Add support for i.MXRT by adding CONFIG_IMXRT in register structure and
adding .compatible = "fsl,imxrt-lcdif".
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Allow using DM CLK instead of mxs_set_lcdclk() so we can avoid to
implement a special function to set lcd clock on i.MXRT.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Since video_ctfb_mode_to_display_timing() has been implemented by moving
sunxi_ctfb_mode_to_display_timing() to video_modes.c and it's meant to be
used by other video subsystem, let's use it instead of local
sunxi_ctfb_mode_to_display_timing().
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This function converts from "struct ctf_res_modes" to
"struct display_timing".
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Need to add set_parent() callback to allow dts assigned-clock-parents to
work so let's add it accordingly.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
mxsfb needs PLL5 as source, so let's setup it at its default frequency
specified in RM(650Mhz).
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
"video:" must be "video", ":" is a typo.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
pllv3 PLLs have powerdown/up bits but enable bits too. Specifically
"enable bit" enable the pll output, so when dis/enabling pll by
setting/clearing power_bit we must also set/clear enable_bit.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Fix some errors pointed out by 'make refcheckdocs'.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Display TEE version at information level; this patch replaces
debug() call to dev_info() in print_os_revision() function.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Jens Wiklander <jens.wiklander@linaro.org>
Currently ATA commands are defined both in include/libata.h and
include/ata.h. Use the command definitions from include/libata.h where
applicable.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
If CONFIG_CMD_NAND is disabled, get_nand_dev_by_index() is not
accessible.
This fix allows the build to succeed in this case.
Signed-off-by: Francois Gervais <fgervais@distech-controls.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add a simple pincontrol associated to the sandbox gpio driver,
that allows to check pin configuration with the command pinmux.
The pinmux test is also updated to test behavior with 2 pincontrols.
Example to check LED pin configuration:
=> pinmux list
| Device | Driver | Parent
| pinctrl-gpio | sandbox_pinctrl_gpio | root_driver
| pinctrl | sandbox_pinctrl | root_driver
=> pinmux dev pinctrl-gpio
=> pinmux status
a0 : gpio input .
a1 : gpio input .
a2 : gpio input .
a3 : gpio input .
a4 : gpio input .
a5 : gpio output .
a6 : gpio output .
...
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add tests for new API set_dir_flags and set_dir_flags and associated
code in gpio uclass.
Test support for new flags GPIO_OPEN_DRAIN, GPIO_OPEN_SOURCE
GPIO_PULL_UP and GPIO_PULL_DOWN.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Cleanup binding support, use the generic binding by default
(test u-class gpio_xlate_offs_flags function) and add
specific binding for added value.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add test for "pins" configuration in gpio uclass with set_state() ops
and test for generic parsing of pinconf_param array).
set_state() is called by:
- pinctrl_generic_set_state
|- pinctrl_generic_set_state_subnode
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add param information in pin information output.
This update prepare unitary test for pin configuration
in pinctrl node.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the ops for GPIO driver set_dir_flags() to set the dir flags.
The user can update the direction and configuration
of each GPIO with a only call to dm_gpio_set_dir_flags() or
dm_gpio_set_dir() and respecting the configuration provided by
device tree (saved in desc->flags).
When these optional ops are absent, the gpio uclass use the mandatory
ops (direction_output, direction_input, get_value) and desc->flags
to manage only the main dir flags:
- GPIOD_IS_IN
- GPIOD_IS_OUT
- GPIOD_IS_OUT_ACTIVE
- GPIOD_ACTIVE_LOW
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the ops for GPIO driver get_dir_flags(), allows to get dynamically
the current gpio configuration; it is used by the API function
dm_gpio_get_dir_flags().
When these optional ops are absent, the gpio uclass continues to use
the mandatory ops (direction_output, direction_input, get_value) and
value of desc->flags to manage only the main dir flags:
- GPIOD_IS_IN
- GPIOD_IS_OUT
- GPIOD_IS_OUT_ACTIVE
- GPIOD_ACTIVE_LOW
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit manages the new dir flags that can be used in gpio
specifiers to indicate the pull-up or pull-down resistor
configuration for output gpio (GPIO_PULL_UP, GPIO_PULL_DOWN)
or the Open Drain/Open Source configuration for input gpio
(GPIO_OPEN_DRAIN, GPIO_OPEN_SOURCE).
These flags are already supported in Linux kernel in gpio lib.
This patch only parse and save the direction flags in GPIO
descriptor (desc->flags), it prepares the introduction of new ops
to manage them.
The GPIO uclass supports new GPIO flags from device-tree
(GPIO_XXX define in include/dt-bindings/gpio/gpio.h)
and translate them in the dir flags (GPIOD_XXX):
- GPIO_PULL_UP => GPIOD_PULL_UP
- GPIO_PULL_DOWN => GPIOD_PULL_DOWN
- GPIO_OPEN_DRAIN => GPIOD_OPEN_DRAIN
- GPIO_OPEN_SOURCE => GPIOD_OPEN_SOURCE
This patch also adds protection in the check_dir_flags function for
new invalid configuration of the dir flags.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the flag management in GPIO uclass: the desc->flags is always
combined with the requested flags and the GPIO descriptor is updated
for further call.
Add a function dm_gpio_get_dir_flags to get dynamically
the current dir_flags (configuration and value).
This patch prepare introduction of the dir flags support with new ops.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a macro to provide the GPIO output value according
the dir flags content.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a dir flags validity check with a new function
check_dir_flags.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce the function _dm_gpio_set_dir_flags to set dir flags
without check if the GPIO is reserved.
Separate the reserved check for "set_dir" and "set_dir_flags".
This patch is a preliminary step to add new ops.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce the function _gpio_get_value to get the GPIO value
without check if it is reserved.
This patch prepare new ops introduction.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a helper function gpio_desc_init() to initialize the gpio descriptor;
with this function the flags will be always set to 0.
It wasn't the case before this patch in dm_gpio_lookup_name.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch removes the ops get_open_drain/set_open_drain
and the API dm_gpio_get_open_drain/dm_gpio_set_open_drain.
The ops only provided in one driver (mpc8xxx gpio) and the
associated API is never called in boards.
This patch prepare a more generic set/get_dir_flags ops,
including the open drain property.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Migrate pinctrl-generic to livetree:
- dev_for_each_property
- dev_read_prop_by_prop
- dev_read_string_count
- dev_read_string_index
and get rid of DECLARE_GLOBAL_DATA_PTR.
This patch solves the parsing issue during sandbox tests for pin
configuration (OF_LIVE is activated in sandbox_defconfig
and sub node are not correctly parsed in
pinctrl_generic_set_state_subnode with fdt lib API).
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add functions to iterate on all property with livetree
- dev_read_first_prop
- dev_read_next_prop
- dev_read_prop_by_prop
and
- ofnode_get_first_property
- ofnode_get_next_property
- ofnode_get_property_by_prop
And helper: dev_for_each_property
For example:
struct ofprop property;
dev_for_each_property(property, config) {
value = dev_read_prop_by_prop(&property, &propname, &len);
or:
for (res = ofnode_get_first_property(node, &property);
!res;
res = ofnode_get_next_property(&property))
{
value = ofnode_get_property_by_prop(&property, &propname, &len);
....
}
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert 'pinctrl-single' using livetree functions
- dev_read_prop
- dev_read_u32_default
- dev_read_u32_array
- dev_read_bool
- dev_read_addr
and get rid of DECLARE_GLOBAL_DATA_PTR.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This is pretty minor set of changes mostly touching HSDK board:
* Enable on-chip reset controller on HSDK
* Add possibility to turn-on & off L2$ on more
recent ARC HS processors.
* AXI tunnel clock calculation on HSDK
This pull request
* provides an implementation of UEFI secure booting
* fixes a problem with the rsa_mod_exp driver which stops some boards
from booting when CONFIG_RSA is enabled which is needed for UEFI
secure booting
* enables the EFI_RNG_PROTOCOL if DM_RNG is enabled
* fixes some function comments
-----BEGIN PGP SIGNATURE-----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=+ZDZ
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-07-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-07-rc1
This pull request
* provides an implementation of UEFI secure booting
* fixes a problem with the rsa_mod_exp driver which stops some boards
from booting when CONFIG_RSA is enabled which is needed for UEFI
secure booting
* enables the EFI_RNG_PROTOCOL if DM_RNG is enabled
* fixes some function comments
We set wrong tunnel PLL frequency when we request 125MHz tunnel clock.
Fix that.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
