diff --git a/README b/README index b81500f6af..128734134b 100644 --- a/README +++ b/README @@ -1696,11 +1696,6 @@ The following options need to be configured: - CONFIG_SYS_OMAP24_I2C_SPEED4 speed channel 4 - CONFIG_SYS_OMAP24_I2C_SLAVE4 slave addr channel 4 - - drivers/i2c/zynq_i2c.c - - activate this driver with CONFIG_SYS_I2C_ZYNQ - - set CONFIG_SYS_I2C_ZYNQ_SPEED for speed setting - - set CONFIG_SYS_I2C_ZYNQ_SLAVE for slave addr - - drivers/i2c/s3c24x0_i2c.c: - activate this driver with CONFIG_SYS_I2C_S3C24X0 - This driver adds i2c buses (11 for Exynos5250, Exynos5420 diff --git a/drivers/i2c/Kconfig b/drivers/i2c/Kconfig index d83afe4dc6..b6bc678091 100644 --- a/drivers/i2c/Kconfig +++ b/drivers/i2c/Kconfig @@ -456,39 +456,6 @@ config SYS_I2C_XILINX_XIIC help Support for Xilinx AXI I2C controller. -config SYS_I2C_ZYNQ - bool "Xilinx I2C driver" - depends on ARCH_ZYNQMP || ARCH_ZYNQ - depends on !DM_I2C - help - Support for Xilinx I2C controller. - -config SYS_I2C_ZYNQ_SLAVE - hex "Set slave addr" - depends on SYS_I2C_ZYNQ - default 0 - help - Set CONFIG_SYS_I2C_ZYNQ_SLAVE for slave addr. - -config SYS_I2C_ZYNQ_SPEED - int "Set I2C speed" - depends on SYS_I2C_ZYNQ - default 100000 - help - Set CONFIG_SYS_I2C_ZYNQ_SPEED for speed setting. - -config ZYNQ_I2C0 - bool "Xilinx I2C0 controller" - depends on SYS_I2C_ZYNQ - help - Enable Xilinx I2C0 controller. - -config ZYNQ_I2C1 - bool "Xilinx I2C1 controller" - depends on SYS_I2C_ZYNQ - help - Enable Xilinx I2C1 controller. - config SYS_I2C_IHS bool "gdsys IHS I2C driver" depends on DM_I2C diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile index ec2d1964c3..dc40055efb 100644 --- a/drivers/i2c/Makefile +++ b/drivers/i2c/Makefile @@ -38,7 +38,6 @@ obj-$(CONFIG_SYS_I2C_UNIPHIER) += i2c-uniphier.o obj-$(CONFIG_SYS_I2C_UNIPHIER_F) += i2c-uniphier-f.o obj-$(CONFIG_SYS_I2C_VERSATILE) += i2c-versatile.o obj-$(CONFIG_SYS_I2C_XILINX_XIIC) += xilinx_xiic.o -obj-$(CONFIG_SYS_I2C_ZYNQ) += zynq_i2c.o obj-$(CONFIG_TEGRA186_BPMP_I2C) += tegra186_bpmp_i2c.o obj-$(CONFIG_I2C_MUX) += muxes/ diff --git a/drivers/i2c/zynq_i2c.c b/drivers/i2c/zynq_i2c.c deleted file mode 100644 index da25067c21..0000000000 --- a/drivers/i2c/zynq_i2c.c +++ /dev/null @@ -1,313 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Driver for the Zynq-7000 PS I2C controller - * IP from Cadence (ID T-CS-PE-0007-100, Version R1p10f2) - * - * Author: Joe Hershberger - * Copyright (c) 2012 Joe Hershberger. - * - * Copyright (c) 2012-2013 Xilinx, Michal Simek - * - * NOTE: This driver should be converted to driver model before June 2017. - * Please see doc/driver-model/i2c-howto.txt for instructions. - */ - -#include -#include -#include -#include -#include - -/* i2c register set */ -struct zynq_i2c_registers { - u32 control; - u32 status; - u32 address; - u32 data; - u32 interrupt_status; - u32 transfer_size; - u32 slave_mon_pause; - u32 time_out; - u32 interrupt_mask; - u32 interrupt_enable; - u32 interrupt_disable; -}; - -/* Control register fields */ -#define ZYNQ_I2C_CONTROL_RW 0x00000001 -#define ZYNQ_I2C_CONTROL_MS 0x00000002 -#define ZYNQ_I2C_CONTROL_NEA 0x00000004 -#define ZYNQ_I2C_CONTROL_ACKEN 0x00000008 -#define ZYNQ_I2C_CONTROL_HOLD 0x00000010 -#define ZYNQ_I2C_CONTROL_SLVMON 0x00000020 -#define ZYNQ_I2C_CONTROL_CLR_FIFO 0x00000040 -#define ZYNQ_I2C_CONTROL_DIV_B_SHIFT 8 -#define ZYNQ_I2C_CONTROL_DIV_B_MASK 0x00003F00 -#define ZYNQ_I2C_CONTROL_DIV_A_SHIFT 14 -#define ZYNQ_I2C_CONTROL_DIV_A_MASK 0x0000C000 - -/* Status register values */ -#define ZYNQ_I2C_STATUS_RXDV 0x00000020 -#define ZYNQ_I2C_STATUS_TXDV 0x00000040 -#define ZYNQ_I2C_STATUS_RXOVF 0x00000080 -#define ZYNQ_I2C_STATUS_BA 0x00000100 - -/* Interrupt register fields */ -#define ZYNQ_I2C_INTERRUPT_COMP 0x00000001 -#define ZYNQ_I2C_INTERRUPT_DATA 0x00000002 -#define ZYNQ_I2C_INTERRUPT_NACK 0x00000004 -#define ZYNQ_I2C_INTERRUPT_TO 0x00000008 -#define ZYNQ_I2C_INTERRUPT_SLVRDY 0x00000010 -#define ZYNQ_I2C_INTERRUPT_RXOVF 0x00000020 -#define ZYNQ_I2C_INTERRUPT_TXOVF 0x00000040 -#define ZYNQ_I2C_INTERRUPT_RXUNF 0x00000080 -#define ZYNQ_I2C_INTERRUPT_ARBLOST 0x00000200 - -#define ZYNQ_I2C_FIFO_DEPTH 16 -#define ZYNQ_I2C_TRANSFERT_SIZE_MAX 255 /* Controller transfer limit */ - -static struct zynq_i2c_registers *i2c_select(struct i2c_adapter *adap) -{ - return adap->hwadapnr ? - /* Zynq PS I2C1 */ - (struct zynq_i2c_registers *)ZYNQ_I2C_BASEADDR1 : - /* Zynq PS I2C0 */ - (struct zynq_i2c_registers *)ZYNQ_I2C_BASEADDR0; -} - -/* I2C init called by cmd_i2c when doing 'i2c reset'. */ -static void zynq_i2c_init(struct i2c_adapter *adap, int requested_speed, - int slaveadd) -{ - struct zynq_i2c_registers *zynq_i2c = i2c_select(adap); - - /* 111MHz / ( (3 * 17) * 22 ) = ~100KHz */ - writel((16 << ZYNQ_I2C_CONTROL_DIV_B_SHIFT) | - (2 << ZYNQ_I2C_CONTROL_DIV_A_SHIFT), &zynq_i2c->control); - - /* Enable master mode, ack, and 7-bit addressing */ - setbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_MS | - ZYNQ_I2C_CONTROL_ACKEN | ZYNQ_I2C_CONTROL_NEA); -} - -#ifdef DEBUG -static void zynq_i2c_debug_status(struct zynq_i2c_registers *zynq_i2c) -{ - int int_status; - int status; - int_status = readl(&zynq_i2c->interrupt_status); - - status = readl(&zynq_i2c->status); - if (int_status || status) { - debug("Status: "); - if (int_status & ZYNQ_I2C_INTERRUPT_COMP) - debug("COMP "); - if (int_status & ZYNQ_I2C_INTERRUPT_DATA) - debug("DATA "); - if (int_status & ZYNQ_I2C_INTERRUPT_NACK) - debug("NACK "); - if (int_status & ZYNQ_I2C_INTERRUPT_TO) - debug("TO "); - if (int_status & ZYNQ_I2C_INTERRUPT_SLVRDY) - debug("SLVRDY "); - if (int_status & ZYNQ_I2C_INTERRUPT_RXOVF) - debug("RXOVF "); - if (int_status & ZYNQ_I2C_INTERRUPT_TXOVF) - debug("TXOVF "); - if (int_status & ZYNQ_I2C_INTERRUPT_RXUNF) - debug("RXUNF "); - if (int_status & ZYNQ_I2C_INTERRUPT_ARBLOST) - debug("ARBLOST "); - if (status & ZYNQ_I2C_STATUS_RXDV) - debug("RXDV "); - if (status & ZYNQ_I2C_STATUS_TXDV) - debug("TXDV "); - if (status & ZYNQ_I2C_STATUS_RXOVF) - debug("RXOVF "); - if (status & ZYNQ_I2C_STATUS_BA) - debug("BA "); - debug("TS%d ", readl(&zynq_i2c->transfer_size)); - debug("\n"); - } -} -#endif - -/* Wait for an interrupt */ -static u32 zynq_i2c_wait(struct zynq_i2c_registers *zynq_i2c, u32 mask) -{ - int timeout, int_status; - - for (timeout = 0; timeout < 100; timeout++) { - udelay(100); - int_status = readl(&zynq_i2c->interrupt_status); - if (int_status & mask) - break; - } -#ifdef DEBUG - zynq_i2c_debug_status(zynq_i2c); -#endif - /* Clear interrupt status flags */ - writel(int_status & mask, &zynq_i2c->interrupt_status); - - return int_status & mask; -} - -/* - * I2C probe called by cmd_i2c when doing 'i2c probe'. - * Begin read, nak data byte, end. - */ -static int zynq_i2c_probe(struct i2c_adapter *adap, u8 dev) -{ - struct zynq_i2c_registers *zynq_i2c = i2c_select(adap); - - /* Attempt to read a byte */ - setbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_CLR_FIFO | - ZYNQ_I2C_CONTROL_RW); - clrbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_HOLD); - writel(0xFF, &zynq_i2c->interrupt_status); - writel(dev, &zynq_i2c->address); - writel(1, &zynq_i2c->transfer_size); - - return (zynq_i2c_wait(zynq_i2c, ZYNQ_I2C_INTERRUPT_COMP | - ZYNQ_I2C_INTERRUPT_NACK) & - ZYNQ_I2C_INTERRUPT_COMP) ? 0 : -ETIMEDOUT; -} - -/* - * I2C read called by cmd_i2c when doing 'i2c read' and by cmd_eeprom.c - * Begin write, send address byte(s), begin read, receive data bytes, end. - */ -static int zynq_i2c_read(struct i2c_adapter *adap, u8 dev, uint addr, - int alen, u8 *data, int length) -{ - u32 status; - u32 i = 0; - u8 *cur_data = data; - struct zynq_i2c_registers *zynq_i2c = i2c_select(adap); - - /* Check the hardware can handle the requested bytes */ - if ((length < 0) || (length > ZYNQ_I2C_TRANSFERT_SIZE_MAX)) - return -EINVAL; - - /* Write the register address */ - setbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_CLR_FIFO | - ZYNQ_I2C_CONTROL_HOLD); - /* - * Temporarily disable restart (by clearing hold) - * It doesn't seem to work. - */ - clrbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_HOLD); - writel(0xFF, &zynq_i2c->interrupt_status); - if (alen) { - clrbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_RW); - writel(dev, &zynq_i2c->address); - while (alen--) - writel(addr >> (8 * alen), &zynq_i2c->data); - - /* Wait for the address to be sent */ - if (!zynq_i2c_wait(zynq_i2c, ZYNQ_I2C_INTERRUPT_COMP)) { - /* Release the bus */ - clrbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_HOLD); - return -ETIMEDOUT; - } - debug("Device acked address\n"); - } - - setbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_CLR_FIFO | - ZYNQ_I2C_CONTROL_RW); - /* Start reading data */ - writel(dev, &zynq_i2c->address); - writel(length, &zynq_i2c->transfer_size); - - /* Wait for data */ - do { - status = zynq_i2c_wait(zynq_i2c, ZYNQ_I2C_INTERRUPT_COMP | - ZYNQ_I2C_INTERRUPT_DATA); - if (!status) { - /* Release the bus */ - clrbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_HOLD); - return -ETIMEDOUT; - } - debug("Read %d bytes\n", - length - readl(&zynq_i2c->transfer_size)); - for (; i < length - readl(&zynq_i2c->transfer_size); i++) - *(cur_data++) = readl(&zynq_i2c->data); - } while (readl(&zynq_i2c->transfer_size) != 0); - /* All done... release the bus */ - clrbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_HOLD); - -#ifdef DEBUG - zynq_i2c_debug_status(zynq_i2c); -#endif - return 0; -} - -/* - * I2C write called by cmd_i2c when doing 'i2c write' and by cmd_eeprom.c - * Begin write, send address byte(s), send data bytes, end. - */ -static int zynq_i2c_write(struct i2c_adapter *adap, u8 dev, uint addr, - int alen, u8 *data, int length) -{ - u8 *cur_data = data; - struct zynq_i2c_registers *zynq_i2c = i2c_select(adap); - - /* Write the register address */ - setbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_CLR_FIFO | - ZYNQ_I2C_CONTROL_HOLD); - clrbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_RW); - writel(0xFF, &zynq_i2c->interrupt_status); - writel(dev, &zynq_i2c->address); - if (alen) { - while (alen--) - writel(addr >> (8 * alen), &zynq_i2c->data); - /* Start the tranfer */ - if (!zynq_i2c_wait(zynq_i2c, ZYNQ_I2C_INTERRUPT_COMP)) { - /* Release the bus */ - clrbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_HOLD); - return -ETIMEDOUT; - } - debug("Device acked address\n"); - } - - while (length--) { - writel(*(cur_data++), &zynq_i2c->data); - if (readl(&zynq_i2c->transfer_size) == ZYNQ_I2C_FIFO_DEPTH) { - if (!zynq_i2c_wait(zynq_i2c, ZYNQ_I2C_INTERRUPT_COMP)) { - /* Release the bus */ - clrbits_le32(&zynq_i2c->control, - ZYNQ_I2C_CONTROL_HOLD); - return -ETIMEDOUT; - } - } - } - - /* All done... release the bus */ - clrbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_HOLD); - /* Wait for the address and data to be sent */ - if (!zynq_i2c_wait(zynq_i2c, ZYNQ_I2C_INTERRUPT_COMP)) - return -ETIMEDOUT; - return 0; -} - -static unsigned int zynq_i2c_set_bus_speed(struct i2c_adapter *adap, - unsigned int speed) -{ - if (speed != 1000000) - return -EINVAL; - - return 0; -} - -#ifdef CONFIG_ZYNQ_I2C0 -U_BOOT_I2C_ADAP_COMPLETE(zynq_0, zynq_i2c_init, zynq_i2c_probe, zynq_i2c_read, - zynq_i2c_write, zynq_i2c_set_bus_speed, - CONFIG_SYS_I2C_ZYNQ_SPEED, CONFIG_SYS_I2C_ZYNQ_SLAVE, - 0) -#endif -#ifdef CONFIG_ZYNQ_I2C1 -U_BOOT_I2C_ADAP_COMPLETE(zynq_1, zynq_i2c_init, zynq_i2c_probe, zynq_i2c_read, - zynq_i2c_write, zynq_i2c_set_bus_speed, - CONFIG_SYS_I2C_ZYNQ_SPEED, CONFIG_SYS_I2C_ZYNQ_SLAVE, - 1) -#endif