sun7i: a20: Add Bananapi M1 Plus support

Banana Pi M1 Plus is an open-source single-board computer
that adds more connectivity to the classic board using
Allwinner A20 SOC.

Bananapi M1-Plus features:
- A20 Dual-core 1.0GHz
- 1 GB DDR3 SDRAM
- MicroSD
- 10/100/1000 Ethernet RJ45
- WiFi b/g/n
- 5V DC Micro USB power-supply

For dts file,
Sync with Linux commit f92ca09("Merge branch 'akpm/master'").

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

arch/arm/dts/sun7i-a20-bananapi-m1-plus.dts

@@ -105,6 +105,10 @@
 	status = "okay";
 };
 
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
 &ehci0 {
 	status = "okay";
 };
@@ -132,16 +136,14 @@
 	status = "okay";
 
 	axp209: pmic@34 {
-		compatible = "x-powers,axp209";
 		reg = <0x34>;
 		interrupt-parent = <&nmi_intc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-
-		interrupt-controller;
-		#interrupt-cells = <1>;
 	};
 };
 
+#include "axp209.dtsi"
+
 &ir0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ir0_rx_pins_a>;
@@ -167,10 +169,10 @@
 	mmc-pwrseq = <&mmc3_pwrseq>;
 	bus-width = <4>;
 	non-removable;
-	enable-sdio-wakeup;
+	wakeup-source;
 	status = "okay";
 
-	brcmf: bcrmf@1 {
+	brcmf: wifi@1 {
 		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 		interrupt-parent = <&pio>;
@@ -181,7 +183,7 @@
 
 &mmc3_pins_a {
 	/* AP6210 requires pull-up */
-	allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+	bias-pull-up;
 };
 
 &ohci0 {
@@ -192,38 +194,81 @@
 	status = "okay";
 };
 
+&otg_sram {
+	status = "okay";
+};
+
 &pio {
 	gmac_power_pin_bpi_m1p: gmac_power_pin@0 {
-		allwinner,pins = "PH23";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PH23";
+		function = "gpio_out";
 	};
 
 	led_pins_bpi_m1p: led_pins@0 {
-		allwinner,pins = "PH24", "PH25";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PH24", "PH25";
+		function = "gpio_out";
 	};
 
 	mmc0_cd_pin_bpi_m1p: mmc0_cd_pin@0 {
-		allwinner,pins = "PH10";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+		pins = "PH10";
+		function = "gpio_in";
+		bias-pull-up;
 	};
 
 	mmc3_pwrseq_pin_bpi_m1p: mmc3_pwrseq_pin@0 {
-		allwinner,pins = "PH22";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PH22";
+		function = "gpio_out";
 	};
 };
 
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-int-dll";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&reg_usb0_vbus {
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;
 	status = "okay";
 };
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb_power_supply {
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+	usb0_vbus_power-supply = <&usb_power_supply>;
+	usb0_vbus-supply = <&reg_usb0_vbus>;
+	/* VBUS on usb host ports are tied to DC5V and therefore always on */
+	status = "okay";
+};

board/sunxi/MAINTAINERS

@@ -118,6 +118,11 @@ M:	Paul Kocialkowski <contact@paulk.fr>
 S:	Maintained
 F:	configs/Ampe_A76_defconfig
 
+BANANAPI M1 PLUS
+M:	Jagan Teki <jagan@amarulasolutions.com>
+S:	Maintained
+F:	configs/bananapi_m1_plus_defconfig
+
 BANANAPI M2 ULTRA BOARD
 M:	Chen-Yu Tsai <wens@csie.org>
 S:	Maintained

configs/bananapi_m1_plus_defconfig

@@ -0,0 +1,24 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN7I=y
+CONFIG_DRAM_CLK=432
+CONFIG_MACPWR="PH23"
+CONFIG_VIDEO_COMPOSITE=y
+CONFIG_GMAC_TX_DELAY=3
+CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-bananapi-m1-plus"
+CONFIG_AHCI=y
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+CONFIG_SPL_I2C_SUPPORT=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_SPL_ISO_PARTITION is not set
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_NETCONSOLE=y
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_RGMII=y
+CONFIG_SUN7I_GMAC=y
+CONFIG_SCSI=y
+CONFIG_USB_EHCI_HCD=y