armv8: ls1046ardb: Add LS1046ARDB board support
LS1046ARDB Specification: ------------------------- Memory subsystem: * 8GByte DDR4 SDRAM (64bit bus) * 512 Mbyte NAND flash * Two 64 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card * On-board 4G eMMC Ethernet: * Two XFI 10G ports * Two SGMII ports * Two RGMII ports PCIe: * PCIe1 (SerDes2 Lane0) to miniPCIe slot * PCIe2 (SerDes2 Lane1) to x2 PCIe slot * PCIe3 (SerDes2 Lane2) to x4 PCIe slot SATA: * SerDes2 Lane3 to SATA port USB 3.0: one super speed USB 3.0 type A port one Micro-AB port UART: supports two UARTs up to 115200 bps for console Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
This commit is contained in:
Mingkai Hu
York Sun
parent
1b2b406636
commit
dd02936f81
@ -841,6 +841,18 @@ config TARGET_LS1043ARDB
|
||||
help
|
||||
Support for Freescale LS1043ARDB platform.
|
||||
|
||||
config TARGET_LS1046ARDB
|
||||
bool "Support ls1046ardb"
|
||||
select ARM64
|
||||
select ARMV8_MULTIENTRY
|
||||
select SUPPORT_SPL
|
||||
select DM_SPI_FLASH if DM_SPI
|
||||
help
|
||||
Support for Freescale LS1046ARDB platform.
|
||||
The LS1046A Reference Design Board (RDB) is a high-performance
|
||||
development platform that supports the QorIQ LS1046A
|
||||
Layerscape Architecture processor.
|
||||
|
||||
config TARGET_H2200
|
||||
bool "Support h2200"
|
||||
select CPU_PXA
|
||||
@ -985,6 +997,7 @@ source "board/freescale/ls1021aqds/Kconfig"
|
||||
source "board/freescale/ls1043aqds/Kconfig"
|
||||
source "board/freescale/ls1021atwr/Kconfig"
|
||||
source "board/freescale/ls1043ardb/Kconfig"
|
||||
source "board/freescale/ls1046ardb/Kconfig"
|
||||
source "board/freescale/ls1012aqds/Kconfig"
|
||||
source "board/freescale/ls1012ardb/Kconfig"
|
||||
source "board/freescale/ls1012afrdm/Kconfig"
|
||||
|
||||
@ -143,6 +143,7 @@ dtb-$(CONFIG_FSL_LSCH3) += fsl-ls2080a-qds.dtb \
|
||||
dtb-$(CONFIG_FSL_LSCH2) += fsl-ls1043a-qds-duart.dtb \
|
||||
fsl-ls1043a-qds-lpuart.dtb \
|
||||
fsl-ls1043a-rdb.dtb \
|
||||
fsl-ls1046a-rdb.dtb \
|
||||
fsl-ls1012a-qds.dtb \
|
||||
fsl-ls1012a-rdb.dtb \
|
||||
fsl-ls1012a-frdm.dtb
|
||||
|
||||
44
arch/arm/dts/fsl-ls1046a-rdb.dts
Normal file
44
arch/arm/dts/fsl-ls1046a-rdb.dts
Normal file
@ -0,0 +1,44 @@
|
||||
/*
|
||||
* Device Tree Include file for Freescale Layerscape-1046A family SoC.
|
||||
*
|
||||
* Copyright 2016, Freescale Semiconductor
|
||||
*
|
||||
* Mingkai Hu <Mingkai.hu@freescale.com>
|
||||
*
|
||||
* This file is licensed under the terms of the GNU General Public
|
||||
* License version 2. This program is licensed "as is" without any
|
||||
* warranty of any kind, whether express or implied.
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
/include/ "fsl-ls1046a.dtsi"
|
||||
|
||||
/ {
|
||||
model = "LS1046A RDB Board";
|
||||
|
||||
aliases {
|
||||
spi0 = &qspi;
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
&qspi {
|
||||
bus-num = <0>;
|
||||
status = "okay";
|
||||
|
||||
qflash0: s25fs512s@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "spi-flash";
|
||||
spi-max-frequency = <50000000>;
|
||||
reg = <0>;
|
||||
};
|
||||
|
||||
qflash1: s25fs512s@1 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "spi-flash";
|
||||
spi-max-frequency = <50000000>;
|
||||
reg = <1>;
|
||||
};
|
||||
};
|
||||
166
arch/arm/dts/fsl-ls1046a.dtsi
Normal file
166
arch/arm/dts/fsl-ls1046a.dtsi
Normal file
@ -0,0 +1,166 @@
|
||||
/*
|
||||
* Device Tree Include file for Freescale Layerscape-1046A family SoC.
|
||||
*
|
||||
* Copyright (C) 2016, Freescale Semiconductor
|
||||
*
|
||||
* Mingkai Hu <mingkai.hu@nxp.com>
|
||||
*
|
||||
* This file is licensed under the terms of the GNU General Public
|
||||
* License version 2. This program is licensed "as is" without any
|
||||
* warranty of any kind, whether express or implied.
|
||||
*/
|
||||
|
||||
/include/ "skeleton64.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "fsl,ls1046a";
|
||||
interrupt-parent = <&gic>;
|
||||
|
||||
sysclk: sysclk {
|
||||
compatible = "fixed-clock";
|
||||
#clock-cells = <0>;
|
||||
clock-frequency = <100000000>;
|
||||
clock-output-names = "sysclk";
|
||||
};
|
||||
|
||||
gic: interrupt-controller@1400000 {
|
||||
compatible = "arm,gic-400";
|
||||
#interrupt-cells = <3>;
|
||||
interrupt-controller;
|
||||
reg = <0x0 0x1410000 0 0x10000>, /* GICD */
|
||||
<0x0 0x1420000 0 0x10000>, /* GICC */
|
||||
<0x0 0x1440000 0 0x20000>, /* GICH */
|
||||
<0x0 0x1460000 0 0x20000>; /* GICV */
|
||||
interrupts = <1 9 0xf08>;
|
||||
};
|
||||
|
||||
soc {
|
||||
compatible = "simple-bus";
|
||||
#address-cells = <2>;
|
||||
#size-cells = <2>;
|
||||
ranges;
|
||||
|
||||
clockgen: clocking@1ee1000 {
|
||||
compatible = "fsl,ls1046a-clockgen";
|
||||
reg = <0x0 0x1ee1000 0x0 0x1000>;
|
||||
#clock-cells = <2>;
|
||||
clocks = <&sysclk>;
|
||||
};
|
||||
|
||||
dspi0: dspi@2100000 {
|
||||
compatible = "fsl,vf610-dspi";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0x0 0x2100000 0x0 0x10000>;
|
||||
interrupts = <0 64 0x4>;
|
||||
clock-names = "dspi";
|
||||
clocks = <&clockgen 4 0>;
|
||||
num-cs = <6>;
|
||||
big-endian;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
dspi1: dspi@2110000 {
|
||||
compatible = "fsl,vf610-dspi";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0x0 0x2110000 0x0 0x10000>;
|
||||
interrupts = <0 65 0x4>;
|
||||
clock-names = "dspi";
|
||||
clocks = <&clockgen 4 0>;
|
||||
num-cs = <6>;
|
||||
big-endian;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
ifc: ifc@1530000 {
|
||||
compatible = "fsl,ifc", "simple-bus";
|
||||
reg = <0x0 0x1530000 0x0 0x10000>;
|
||||
interrupts = <0 43 0x4>;
|
||||
};
|
||||
|
||||
i2c0: i2c@2180000 {
|
||||
compatible = "fsl,vf610-i2c";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0x0 0x2180000 0x0 0x10000>;
|
||||
interrupts = <0 56 0x4>;
|
||||
clock-names = "i2c";
|
||||
clocks = <&clockgen 4 0>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
i2c1: i2c@2190000 {
|
||||
compatible = "fsl,vf610-i2c";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0x0 0x2190000 0x0 0x10000>;
|
||||
interrupts = <0 57 0x4>;
|
||||
clock-names = "i2c";
|
||||
clocks = <&clockgen 4 0>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
i2c2: i2c@21a0000 {
|
||||
compatible = "fsl,vf610-i2c";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0x0 0x21a0000 0x0 0x10000>;
|
||||
interrupts = <0 58 0x4>;
|
||||
clock-names = "i2c";
|
||||
clocks = <&clockgen 4 0>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
i2c3: i2c@21b0000 {
|
||||
compatible = "fsl,vf610-i2c";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0x0 0x21b0000 0x0 0x10000>;
|
||||
interrupts = <0 59 0x4>;
|
||||
clock-names = "i2c";
|
||||
clocks = <&clockgen 4 0>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
duart0: serial@21c0500 {
|
||||
compatible = "fsl,ns16550", "ns16550a";
|
||||
reg = <0x00 0x21c0500 0x0 0x100>;
|
||||
interrupts = <0 54 0x4>;
|
||||
clocks = <&clockgen 4 0>;
|
||||
};
|
||||
|
||||
duart1: serial@21c0600 {
|
||||
compatible = "fsl,ns16550", "ns16550a";
|
||||
reg = <0x00 0x21c0600 0x0 0x100>;
|
||||
interrupts = <0 54 0x4>;
|
||||
clocks = <&clockgen 4 0>;
|
||||
};
|
||||
|
||||
duart2: serial@21d0500 {
|
||||
compatible = "fsl,ns16550", "ns16550a";
|
||||
reg = <0x0 0x21d0500 0x0 0x100>;
|
||||
interrupts = <0 55 0x4>;
|
||||
clocks = <&clockgen 4 0>;
|
||||
};
|
||||
|
||||
duart3: serial@21d0600 {
|
||||
compatible = "fsl,ns16550", "ns16550a";
|
||||
reg = <0x0 0x21d0600 0x0 0x100>;
|
||||
interrupts = <0 55 0x4>;
|
||||
clocks = <&clockgen 4 0>;
|
||||
};
|
||||
|
||||
qspi: quadspi@1550000 {
|
||||
compatible = "fsl,vf610-qspi";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0x0 0x1550000 0x0 0x10000>,
|
||||
<0x0 0x40000000 0x0 0x10000000>;
|
||||
reg-names = "QuadSPI", "QuadSPI-memory";
|
||||
num-cs = <4>;
|
||||
big-endian;
|
||||
status = "disabled";
|
||||
};
|
||||
};
|
||||
};
|
||||
16
board/freescale/ls1046ardb/Kconfig
Normal file
16
board/freescale/ls1046ardb/Kconfig
Normal file
@ -0,0 +1,16 @@
|
||||
|
||||
if TARGET_LS1046ARDB
|
||||
|
||||
config SYS_BOARD
|
||||
default "ls1046ardb"
|
||||
|
||||
config SYS_VENDOR
|
||||
default "freescale"
|
||||
|
||||
config SYS_SOC
|
||||
default "fsl-layerscape"
|
||||
|
||||
config SYS_CONFIG_NAME
|
||||
default "ls1046ardb"
|
||||
|
||||
endif
|
||||
9
board/freescale/ls1046ardb/MAINTAINERS
Normal file
9
board/freescale/ls1046ardb/MAINTAINERS
Normal file
@ -0,0 +1,9 @@
|
||||
LS1046A BOARD
|
||||
M: Mingkai Hu <mingkai.hu@nxp.com>
|
||||
S: Maintained
|
||||
F: board/freescale/ls1046ardb/
|
||||
F: board/freescale/ls1046ardb/ls1046ardb.c
|
||||
F: include/configs/ls1046ardb.h
|
||||
F: configs/ls1046ardb_qspi_defconfig
|
||||
F: configs/ls1046ardb_sdcard_defconfig
|
||||
F: configs/ls1046ardb_emmc_defconfig
|
||||
10
board/freescale/ls1046ardb/Makefile
Normal file
10
board/freescale/ls1046ardb/Makefile
Normal file
@ -0,0 +1,10 @@
|
||||
#
|
||||
# Copyright 2016 Freescale Semiconductor
|
||||
#
|
||||
# SPDX-License-Identifier: GPL-2.0+
|
||||
#
|
||||
|
||||
obj-y += cpld.o
|
||||
obj-y += ddr.o
|
||||
obj-y += ls1046ardb.o
|
||||
obj-$(CONFIG_SYS_DPAA_FMAN) += eth.o
|
||||
76
board/freescale/ls1046ardb/README
Normal file
76
board/freescale/ls1046ardb/README
Normal file
@ -0,0 +1,76 @@
|
||||
Overview
|
||||
--------
|
||||
The LS1046A Reference Design Board (RDB) is a high-performance computing,
|
||||
evaluation, and development platform that supports the QorIQ LS1046A
|
||||
LayerScape Architecture processor. The LS1046ARDB provides SW development
|
||||
platform for the Freescale LS1046A processor series, with a complete
|
||||
debugging environment. The LS1046A RDB is lead-free and RoHS-compliant.
|
||||
|
||||
LS1046A SoC Overview
|
||||
--------------------
|
||||
Please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc for LS1046A
|
||||
SoC overview.
|
||||
|
||||
LS1046ARDB board Overview
|
||||
-----------------------
|
||||
- SERDES1 Connections, 4 lanes supporting:
|
||||
- Lane0: XFI with x1 RJ45 connector
|
||||
- Lane1: XFI Cage
|
||||
- Lane2: SGMII.5
|
||||
- Lane3: SGMII.6
|
||||
- SERDES2 Connections, 4 lanes supporting:
|
||||
- Lane0: PCIe1 with miniPCIe slot
|
||||
- Lane1: PCIe2 with PCIe x2 slot
|
||||
- Lane2: PCIe3 with PCIe x4 slot
|
||||
- Lane3: SATA
|
||||
- DDR Controller
|
||||
- 8GB 64bits DDR4 SDRAM. Support rates of up to 2133MT/s
|
||||
-IFC/Local Bus
|
||||
- One 512 MB NAND flash with ECC support
|
||||
- CPLD connection
|
||||
- USB 3.0
|
||||
- one Type A port, one Micro-AB port
|
||||
- SDHC: connects directly to a full SD/MMC slot
|
||||
- DSPI: 64 MB high-speed flash Memory for boot code and storage (up to 108MHz)
|
||||
- 4 I2C controllers
|
||||
- UART
|
||||
- Two 4-pin serial ports at up to 115.2 Kbit/s
|
||||
- Two DB9 D-Type connectors supporting one Serial port each
|
||||
- ARM JTAG support
|
||||
|
||||
Memory map from core's view
|
||||
----------------------------
|
||||
Start Address End Address Description Size
|
||||
0x00_0000_0000 - 0x00_000F_FFFF Secure Boot ROM 1MB
|
||||
0x00_0100_0000 - 0x00_0FFF_FFFF CCSRBAR 240MB
|
||||
0x00_1000_0000 - 0x00_1000_FFFF OCRAM0 64KB
|
||||
0x00_1001_0000 - 0x00_1001_FFFF OCRAM1 64KB
|
||||
0x00_2000_0000 - 0x00_20FF_FFFF DCSR 16MB
|
||||
0x00_7E80_0000 - 0x00_7E80_FFFF IFC - NAND Flash 64KB
|
||||
0x00_7FB0_0000 - 0x00_7FB0_0FFF IFC - CPLD 4KB
|
||||
0x00_8000_0000 - 0x00_FFFF_FFFF DRAM1 2GB
|
||||
0x05_0000_0000 - 0x05_07FF_FFFF QMAN S/W Portal 128M
|
||||
0x05_0800_0000 - 0x05_0FFF_FFFF BMAN S/W Portal 128M
|
||||
0x08_8000_0000 - 0x09_FFFF_FFFF DRAM2 6GB
|
||||
0x40_0000_0000 - 0x47_FFFF_FFFF PCI Express1 32G
|
||||
0x48_0000_0000 - 0x4F_FFFF_FFFF PCI Express2 32G
|
||||
0x50_0000_0000 - 0x57_FFFF_FFFF PCI Express3 32G
|
||||
|
||||
QSPI flash map:
|
||||
Start Address End Address Description Size
|
||||
0x00_4000_0000 - 0x00_400F_FFFF RCW + PBI 1MB
|
||||
0x00_4010_0000 - 0x00_401F_FFFF U-Boot 1MB
|
||||
0x00_4020_0000 - 0x00_402F_FFFF U-Boot Env 1MB
|
||||
0x00_4030_0000 - 0x00_403F_FFFF FMan ucode 1MB
|
||||
0x00_4040_0000 - 0x00_404F_FFFF UEFI 1MB
|
||||
0x00_4050_0000 - 0x00_406F_FFFF PPA 2MB
|
||||
0x00_4070_0000 - 0x00_408F_FFFF Secure boot header
|
||||
+ bootscript 2MB
|
||||
0x00_4090_0000 - 0x00_40FF_FFFF Reserved 7MB
|
||||
0x00_4100_0000 - 0x00_43FF_FFFF FIT Image 48MB
|
||||
|
||||
Booting Options
|
||||
---------------
|
||||
a) QSPI boot
|
||||
b) SD boot
|
||||
c) eMMC boot
|
||||
158
board/freescale/ls1046ardb/cpld.c
Normal file
158
board/freescale/ls1046ardb/cpld.c
Normal file
@ -0,0 +1,158 @@
|
||||
/*
|
||||
* Copyright 2016 Freescale Semiconductor
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*
|
||||
* Freescale LS1046ARDB board-specific CPLD controlling supports.
|
||||
*/
|
||||
|
||||
#include <common.h>
|
||||
#include <command.h>
|
||||
#include <asm/io.h>
|
||||
#include "cpld.h"
|
||||
|
||||
u8 cpld_read(unsigned int reg)
|
||||
{
|
||||
void *p = (void *)CONFIG_SYS_CPLD_BASE;
|
||||
|
||||
return in_8(p + reg);
|
||||
}
|
||||
|
||||
void cpld_write(unsigned int reg, u8 value)
|
||||
{
|
||||
void *p = (void *)CONFIG_SYS_CPLD_BASE;
|
||||
|
||||
out_8(p + reg, value);
|
||||
}
|
||||
|
||||
/* Set the boot bank to the alternate bank */
|
||||
void cpld_set_altbank(void)
|
||||
{
|
||||
u16 reg = CPLD_CFG_RCW_SRC_QSPI;
|
||||
u8 reg4 = CPLD_READ(soft_mux_on);
|
||||
u8 reg5 = (u8)(reg >> 1);
|
||||
u8 reg6 = (u8)(reg & 1);
|
||||
u8 reg7 = CPLD_READ(vbank);
|
||||
|
||||
cpld_rev_bit(®5);
|
||||
|
||||
CPLD_WRITE(soft_mux_on, reg4 | CPLD_SW_MUX_BANK_SEL | 1);
|
||||
|
||||
CPLD_WRITE(cfg_rcw_src1, reg5);
|
||||
CPLD_WRITE(cfg_rcw_src2, reg6);
|
||||
|
||||
reg7 = (reg7 & ~CPLD_BANK_SEL_MASK) | CPLD_BANK_SEL_ALTBANK;
|
||||
CPLD_WRITE(vbank, reg7);
|
||||
|
||||
CPLD_WRITE(system_rst, 1);
|
||||
}
|
||||
|
||||
/* Set the boot bank to the default bank */
|
||||
void cpld_set_defbank(void)
|
||||
{
|
||||
u16 reg = CPLD_CFG_RCW_SRC_QSPI;
|
||||
u8 reg4 = CPLD_READ(soft_mux_on);
|
||||
u8 reg5 = (u8)(reg >> 1);
|
||||
u8 reg6 = (u8)(reg & 1);
|
||||
|
||||
cpld_rev_bit(®5);
|
||||
|
||||
CPLD_WRITE(soft_mux_on, reg4 | CPLD_SW_MUX_BANK_SEL | 1);
|
||||
|
||||
CPLD_WRITE(cfg_rcw_src1, reg5);
|
||||
CPLD_WRITE(cfg_rcw_src2, reg6);
|
||||
|
||||
CPLD_WRITE(vbank, 0);
|
||||
|
||||
CPLD_WRITE(system_rst, 1);
|
||||
}
|
||||
|
||||
void cpld_set_sd(void)
|
||||
{
|
||||
u16 reg = CPLD_CFG_RCW_SRC_SD;
|
||||
u8 reg5 = (u8)(reg >> 1);
|
||||
u8 reg6 = (u8)(reg & 1);
|
||||
|
||||
cpld_rev_bit(®5);
|
||||
|
||||
CPLD_WRITE(soft_mux_on, 1);
|
||||
|
||||
CPLD_WRITE(cfg_rcw_src1, reg5);
|
||||
CPLD_WRITE(cfg_rcw_src2, reg6);
|
||||
|
||||
CPLD_WRITE(system_rst, 1);
|
||||
}
|
||||
#ifdef DEBUG
|
||||
static void cpld_dump_regs(void)
|
||||
{
|
||||
printf("cpld_ver = %x\n", CPLD_READ(cpld_ver));
|
||||
printf("cpld_ver_sub = %x\n", CPLD_READ(cpld_ver_sub));
|
||||
printf("pcba_ver = %x\n", CPLD_READ(pcba_ver));
|
||||
printf("soft_mux_on = %x\n", CPLD_READ(soft_mux_on));
|
||||
printf("cfg_rcw_src1 = %x\n", CPLD_READ(cfg_rcw_src1));
|
||||
printf("cfg_rcw_src2 = %x\n", CPLD_READ(cfg_rcw_src2));
|
||||
printf("vbank = %x\n", CPLD_READ(vbank));
|
||||
printf("sysclk_sel = %x\n", CPLD_READ(sysclk_sel));
|
||||
printf("uart_sel = %x\n", CPLD_READ(uart_sel));
|
||||
printf("sd1refclk_sel = %x\n", CPLD_READ(sd1refclk_sel));
|
||||
printf("rgmii_1588_sel = %x\n", CPLD_READ(rgmii_1588_sel));
|
||||
printf("1588_clk_sel = %x\n", CPLD_READ(reg_1588_clk_sel));
|
||||
printf("status_led = %x\n", CPLD_READ(status_led));
|
||||
printf("sd_emmc = %x\n", CPLD_READ(sd_emmc));
|
||||
printf("vdd_en = %x\n", CPLD_READ(vdd_en));
|
||||
printf("vdd_sel = %x\n", CPLD_READ(vdd_sel));
|
||||
putc('\n');
|
||||
}
|
||||
#endif
|
||||
|
||||
void cpld_rev_bit(unsigned char *value)
|
||||
{
|
||||
u8 rev_val, val;
|
||||
int i;
|
||||
|
||||
val = *value;
|
||||
rev_val = val & 1;
|
||||
for (i = 1; i <= 7; i++) {
|
||||
val >>= 1;
|
||||
rev_val <<= 1;
|
||||
rev_val |= val & 1;
|
||||
}
|
||||
|
||||
*value = rev_val;
|
||||
}
|
||||
|
||||
int do_cpld(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
|
||||
{
|
||||
int rc = 0;
|
||||
|
||||
if (argc <= 1)
|
||||
return cmd_usage(cmdtp);
|
||||
|
||||
if (strcmp(argv[1], "reset") == 0) {
|
||||
if (strcmp(argv[2], "altbank") == 0)
|
||||
cpld_set_altbank();
|
||||
else if (strcmp(argv[2], "sd") == 0)
|
||||
cpld_set_sd();
|
||||
else
|
||||
cpld_set_defbank();
|
||||
#ifdef DEBUG
|
||||
} else if (strcmp(argv[1], "dump") == 0) {
|
||||
cpld_dump_regs();
|
||||
#endif
|
||||
} else {
|
||||
rc = cmd_usage(cmdtp);
|
||||
}
|
||||
|
||||
return rc;
|
||||
}
|
||||
|
||||
U_BOOT_CMD(
|
||||
cpld, CONFIG_SYS_MAXARGS, 1, do_cpld,
|
||||
"Reset the board or alternate bank",
|
||||
"reset: reset to default bank\n"
|
||||
"cpld reset altbank: reset to alternate bank\n"
|
||||
"cpld reset sd: reset to boot from SD card\n"
|
||||
#ifdef DEBUG
|
||||
"cpld dump - display the CPLD registers\n"
|
||||
#endif
|
||||
);
|
||||
49
board/freescale/ls1046ardb/cpld.h
Normal file
49
board/freescale/ls1046ardb/cpld.h
Normal file
@ -0,0 +1,49 @@
|
||||
/*
|
||||
* Copyright 2016 Freescale Semiconductor
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
|
||||
#ifndef __CPLD_H__
|
||||
#define __CPLD_H__
|
||||
|
||||
/*
|
||||
* CPLD register set of LS1046ARDB board-specific.
|
||||
* CPLD Revision: V2.1
|
||||
*/
|
||||
struct cpld_data {
|
||||
u8 cpld_ver; /* 0x0 - CPLD Major Revision Register */
|
||||
u8 cpld_ver_sub; /* 0x1 - CPLD Minor Revision Register */
|
||||
u8 pcba_ver; /* 0x2 - PCBA Revision Register */
|
||||
u8 system_rst; /* 0x3 - system reset register */
|
||||
u8 soft_mux_on; /* 0x4 - Switch Control Enable Register */
|
||||
u8 cfg_rcw_src1; /* 0x5 - RCW Source Location POR Regsiter 1 */
|
||||
u8 cfg_rcw_src2; /* 0x6 - RCW Source Location POR Regsiter 2 */
|
||||
u8 vbank; /* 0x7 - QSPI Flash Bank Setting Register */
|
||||
u8 sysclk_sel; /* 0x8 - System clock POR Register */
|
||||
u8 uart_sel; /* 0x9 - UART1 Connection Control Register */
|
||||
u8 sd1refclk_sel; /* 0xA - */
|
||||
u8 rgmii_1588_sel; /* 0xB - */
|
||||
u8 reg_1588_clk_sel; /* 0xC - */
|
||||
u8 status_led; /* 0xD - */
|
||||
u8 global_rst; /* 0xE - */
|
||||
u8 sd_emmc; /* 0xF - SD/EMMC Interface Control Regsiter */
|
||||
u8 vdd_en; /* 0x10 - VDD Voltage Control Enable Register */
|
||||
u8 vdd_sel; /* 0x11 - VDD Voltage Control Register */
|
||||
};
|
||||
|
||||
u8 cpld_read(unsigned int reg);
|
||||
void cpld_write(unsigned int reg, u8 value);
|
||||
void cpld_rev_bit(unsigned char *value);
|
||||
|
||||
#define CPLD_READ(reg) cpld_read(offsetof(struct cpld_data, reg))
|
||||
#define CPLD_WRITE(reg, value) \
|
||||
cpld_write(offsetof(struct cpld_data, reg), value)
|
||||
|
||||
/* CPLD on IFC */
|
||||
#define CPLD_SW_MUX_BANK_SEL 0x40
|
||||
#define CPLD_BANK_SEL_MASK 0x07
|
||||
#define CPLD_BANK_SEL_ALTBANK 0x04
|
||||
#define CPLD_CFG_RCW_SRC_QSPI 0x044
|
||||
#define CPLD_CFG_RCW_SRC_SD 0x040
|
||||
#endif
|
||||
140
board/freescale/ls1046ardb/ddr.c
Normal file
140
board/freescale/ls1046ardb/ddr.c
Normal file
@ -0,0 +1,140 @@
|
||||
/*
|
||||
* Copyright 2016 Freescale Semiconductor, Inc.
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
|
||||
#include <common.h>
|
||||
#include <fsl_ddr_sdram.h>
|
||||
#include <fsl_ddr_dimm_params.h>
|
||||
#include "ddr.h"
|
||||
#ifdef CONFIG_FSL_DEEP_SLEEP
|
||||
#include <fsl_sleep.h>
|
||||
#endif
|
||||
|
||||
DECLARE_GLOBAL_DATA_PTR;
|
||||
|
||||
void fsl_ddr_board_options(memctl_options_t *popts,
|
||||
dimm_params_t *pdimm,
|
||||
unsigned int ctrl_num)
|
||||
{
|
||||
const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
|
||||
ulong ddr_freq;
|
||||
|
||||
if (ctrl_num > 1) {
|
||||
printf("Not supported controller number %d\n", ctrl_num);
|
||||
return;
|
||||
}
|
||||
if (!pdimm->n_ranks)
|
||||
return;
|
||||
|
||||
pbsp = udimms[0];
|
||||
|
||||
/* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
|
||||
* freqency and n_banks specified in board_specific_parameters table.
|
||||
*/
|
||||
ddr_freq = get_ddr_freq(0) / 1000000;
|
||||
while (pbsp->datarate_mhz_high) {
|
||||
if (pbsp->n_ranks == pdimm->n_ranks) {
|
||||
if (ddr_freq <= pbsp->datarate_mhz_high) {
|
||||
popts->clk_adjust = pbsp->clk_adjust;
|
||||
popts->wrlvl_start = pbsp->wrlvl_start;
|
||||
popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
|
||||
popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
|
||||
goto found;
|
||||
}
|
||||
pbsp_highest = pbsp;
|
||||
}
|
||||
pbsp++;
|
||||
}
|
||||
|
||||
if (pbsp_highest) {
|
||||
printf("Error: board specific timing not found for %lu MT/s\n",
|
||||
ddr_freq);
|
||||
printf("Trying to use the highest speed (%u) parameters\n",
|
||||
pbsp_highest->datarate_mhz_high);
|
||||
popts->clk_adjust = pbsp_highest->clk_adjust;
|
||||
popts->wrlvl_start = pbsp_highest->wrlvl_start;
|
||||
popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
|
||||
popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
|
||||
} else {
|
||||
panic("DIMM is not supported by this board");
|
||||
}
|
||||
found:
|
||||
debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n",
|
||||
pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb);
|
||||
|
||||
popts->data_bus_width = 0; /* 64-bit data bus */
|
||||
popts->otf_burst_chop_en = 0;
|
||||
popts->burst_length = DDR_BL8;
|
||||
popts->bstopre = 0; /* enable auto precharge */
|
||||
|
||||
/*
|
||||
* Factors to consider for half-strength driver enable:
|
||||
* - number of DIMMs installed
|
||||
*/
|
||||
popts->half_strength_driver_enable = 0;
|
||||
/*
|
||||
* Write leveling override
|
||||
*/
|
||||
popts->wrlvl_override = 1;
|
||||
popts->wrlvl_sample = 0xf;
|
||||
|
||||
/*
|
||||
* Rtt and Rtt_WR override
|
||||
*/
|
||||
popts->rtt_override = 0;
|
||||
|
||||
/* Enable ZQ calibration */
|
||||
popts->zq_en = 1;
|
||||
|
||||
popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
|
||||
popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
|
||||
DDR_CDR2_VREF_TRAIN_EN | DDR_CDR2_VREF_RANGE_2;
|
||||
}
|
||||
|
||||
phys_size_t initdram(int board_type)
|
||||
{
|
||||
phys_size_t dram_size;
|
||||
|
||||
#if defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD)
|
||||
return fsl_ddr_sdram_size();
|
||||
#else
|
||||
puts("Initializing DDR....using SPD\n");
|
||||
|
||||
dram_size = fsl_ddr_sdram();
|
||||
#endif
|
||||
|
||||
erratum_a008850_post();
|
||||
|
||||
return dram_size;
|
||||
}
|
||||
|
||||
void dram_init_banksize(void)
|
||||
{
|
||||
/*
|
||||
* gd->arch.secure_ram tracks the location of secure memory.
|
||||
* It was set as if the memory starts from 0.
|
||||
* The address needs to add the offset of its bank.
|
||||
*/
|
||||
gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
|
||||
if (gd->ram_size > CONFIG_SYS_DDR_BLOCK1_SIZE) {
|
||||
gd->bd->bi_dram[0].size = CONFIG_SYS_DDR_BLOCK1_SIZE;
|
||||
gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
|
||||
gd->bd->bi_dram[1].size = gd->ram_size -
|
||||
CONFIG_SYS_DDR_BLOCK1_SIZE;
|
||||
#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
|
||||
gd->arch.secure_ram = gd->bd->bi_dram[1].start +
|
||||
gd->arch.secure_ram -
|
||||
CONFIG_SYS_DDR_BLOCK1_SIZE;
|
||||
gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
|
||||
#endif
|
||||
} else {
|
||||
gd->bd->bi_dram[0].size = gd->ram_size;
|
||||
#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
|
||||
gd->arch.secure_ram = gd->bd->bi_dram[0].start +
|
||||
gd->arch.secure_ram;
|
||||
gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
|
||||
#endif
|
||||
}
|
||||
}
|
||||
44
board/freescale/ls1046ardb/ddr.h
Normal file
44
board/freescale/ls1046ardb/ddr.h
Normal file
@ -0,0 +1,44 @@
|
||||
/*
|
||||
* Copyright 2016 Freescale Semiconductor, Inc.
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
|
||||
#ifndef __DDR_H__
|
||||
#define __DDR_H__
|
||||
|
||||
void erratum_a008850_post(void);
|
||||
|
||||
struct board_specific_parameters {
|
||||
u32 n_ranks;
|
||||
u32 datarate_mhz_high;
|
||||
u32 rank_gb;
|
||||
u32 clk_adjust;
|
||||
u32 wrlvl_start;
|
||||
u32 wrlvl_ctl_2;
|
||||
u32 wrlvl_ctl_3;
|
||||
};
|
||||
|
||||
/*
|
||||
* These tables contain all valid speeds we want to override with board
|
||||
* specific parameters. datarate_mhz_high values need to be in ascending order
|
||||
* for each n_ranks group.
|
||||
*/
|
||||
static const struct board_specific_parameters udimm0[] = {
|
||||
/*
|
||||
* memory controller 0
|
||||
* num| hi| rank| clk| wrlvl | wrlvl | wrlvl
|
||||
* ranks| mhz| GB |adjst| start | ctl2 | ctl3
|
||||
*/
|
||||
{2, 1350, 0, 8, 6, 0x0708090B, 0x0C0D0E09,},
|
||||
{2, 1666, 0, 8, 7, 0x08090A0C, 0x0D0F100B,},
|
||||
{2, 1900, 0, 8, 7, 0x09090B0D, 0x0E10120B,},
|
||||
{2, 2300, 0, 8, 9, 0x0A0B0C10, 0x1213140E,},
|
||||
{}
|
||||
};
|
||||
|
||||
static const struct board_specific_parameters *udimms[] = {
|
||||
udimm0,
|
||||
};
|
||||
|
||||
#endif
|
||||
77
board/freescale/ls1046ardb/eth.c
Normal file
77
board/freescale/ls1046ardb/eth.c
Normal file
@ -0,0 +1,77 @@
|
||||
/*
|
||||
* Copyright 2016 Freescale Semiconductor, Inc.
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
#include <common.h>
|
||||
#include <asm/io.h>
|
||||
#include <netdev.h>
|
||||
#include <fm_eth.h>
|
||||
#include <fsl_dtsec.h>
|
||||
#include <fsl_mdio.h>
|
||||
#include <malloc.h>
|
||||
|
||||
#include "../common/fman.h"
|
||||
|
||||
int board_eth_init(bd_t *bis)
|
||||
{
|
||||
#ifdef CONFIG_FMAN_ENET
|
||||
int i;
|
||||
struct memac_mdio_info dtsec_mdio_info;
|
||||
struct memac_mdio_info tgec_mdio_info;
|
||||
struct mii_dev *dev;
|
||||
u32 srds_s1;
|
||||
struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
|
||||
|
||||
srds_s1 = in_be32(&gur->rcwsr[4]) &
|
||||
FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_MASK;
|
||||
srds_s1 >>= FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT;
|
||||
|
||||
dtsec_mdio_info.regs =
|
||||
(struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR;
|
||||
|
||||
dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
|
||||
|
||||
/* Register the 1G MDIO bus */
|
||||
fm_memac_mdio_init(bis, &dtsec_mdio_info);
|
||||
|
||||
tgec_mdio_info.regs =
|
||||
(struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR;
|
||||
tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME;
|
||||
|
||||
/* Register the 10G MDIO bus */
|
||||
fm_memac_mdio_init(bis, &tgec_mdio_info);
|
||||
|
||||
/* Set the two on-board RGMII PHY address */
|
||||
fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY1_ADDR);
|
||||
fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY2_ADDR);
|
||||
|
||||
/* Set the two on-board SGMII PHY address */
|
||||
fm_info_set_phy_address(FM1_DTSEC5, SGMII_PHY1_ADDR);
|
||||
fm_info_set_phy_address(FM1_DTSEC6, SGMII_PHY2_ADDR);
|
||||
|
||||
/* Set the on-board AQ PHY address */
|
||||
fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR);
|
||||
|
||||
switch (srds_s1) {
|
||||
case 0x1133:
|
||||
break;
|
||||
default:
|
||||
printf("Invalid SerDes protocol 0x%x for LS1046ARDB\n",
|
||||
srds_s1);
|
||||
break;
|
||||
}
|
||||
|
||||
dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
|
||||
for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++)
|
||||
fm_info_set_mdio(i, dev);
|
||||
|
||||
/* XFI on lane A, MAC 9 */
|
||||
dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
|
||||
fm_info_set_mdio(FM1_10GEC1, dev);
|
||||
|
||||
cpu_eth_init(bis);
|
||||
#endif
|
||||
|
||||
return pci_eth_init(bis);
|
||||
}
|
||||
136
board/freescale/ls1046ardb/ls1046ardb.c
Normal file
136
board/freescale/ls1046ardb/ls1046ardb.c
Normal file
@ -0,0 +1,136 @@
|
||||
/*
|
||||
* Copyright 2016 Freescale Semiconductor, Inc.
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
|
||||
#include <common.h>
|
||||
#include <i2c.h>
|
||||
#include <fdt_support.h>
|
||||
#include <asm/io.h>
|
||||
#include <asm/arch/clock.h>
|
||||
#include <asm/arch/fsl_serdes.h>
|
||||
#include <asm/arch/ppa.h>
|
||||
#include <asm/arch/soc.h>
|
||||
#include <hwconfig.h>
|
||||
#include <ahci.h>
|
||||
#include <mmc.h>
|
||||
#include <scsi.h>
|
||||
#include <fm_eth.h>
|
||||
#include <fsl_csu.h>
|
||||
#include <fsl_esdhc.h>
|
||||
#include "cpld.h"
|
||||
|
||||
DECLARE_GLOBAL_DATA_PTR;
|
||||
|
||||
int checkboard(void)
|
||||
{
|
||||
static const char *freq[2] = {"100.00MHZ", "156.25MHZ"};
|
||||
u8 cfg_rcw_src1, cfg_rcw_src2;
|
||||
u16 cfg_rcw_src;
|
||||
u8 sd1refclk_sel;
|
||||
|
||||
puts("Board: LS1046ARDB, boot from ");
|
||||
|
||||
cfg_rcw_src1 = CPLD_READ(cfg_rcw_src1);
|
||||
cfg_rcw_src2 = CPLD_READ(cfg_rcw_src2);
|
||||
cpld_rev_bit(&cfg_rcw_src1);
|
||||
cfg_rcw_src = cfg_rcw_src1;
|
||||
cfg_rcw_src = (cfg_rcw_src << 1) | cfg_rcw_src2;
|
||||
|
||||
if (cfg_rcw_src == 0x44)
|
||||
printf("QSPI vBank %d\n", CPLD_READ(vbank));
|
||||
else if (cfg_rcw_src == 0x40)
|
||||
puts("SD\n");
|
||||
else
|
||||
puts("Invalid setting of SW5\n");
|
||||
|
||||
printf("CPLD: V%x.%x\nPCBA: V%x.0\n", CPLD_READ(cpld_ver),
|
||||
CPLD_READ(cpld_ver_sub), CPLD_READ(pcba_ver));
|
||||
|
||||
puts("SERDES Reference Clocks:\n");
|
||||
sd1refclk_sel = CPLD_READ(sd1refclk_sel);
|
||||
printf("SD1_CLK1 = %s, SD1_CLK2 = %s\n", freq[sd1refclk_sel], freq[0]);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
int dram_init(void)
|
||||
{
|
||||
gd->ram_size = initdram(0);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
int board_early_init_f(void)
|
||||
{
|
||||
fsl_lsch2_early_init_f();
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
int board_init(void)
|
||||
{
|
||||
struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
|
||||
|
||||
#ifdef CONFIG_LAYERSCAPE_NS_ACCESS
|
||||
enable_layerscape_ns_access();
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_FSL_LS_PPA
|
||||
ppa_init();
|
||||
#endif
|
||||
|
||||
/* invert AQR105 IRQ pins polarity */
|
||||
out_be32(&scfg->intpcr, AQR105_IRQ_MASK);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
void config_board_mux(void)
|
||||
{
|
||||
#ifdef CONFIG_HAS_FSL_XHCI_USB
|
||||
struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
|
||||
u32 usb_pwrfault;
|
||||
|
||||
/* USB3 is not used, configure mux to IIC4_SCL/IIC4_SDA */
|
||||
out_be32(&scfg->rcwpmuxcr0, 0x3300);
|
||||
out_be32(&scfg->usbdrvvbus_selcr, SCFG_USBDRVVBUS_SELCR_USB1);
|
||||
usb_pwrfault = (SCFG_USBPWRFAULT_DEDICATED <<
|
||||
SCFG_USBPWRFAULT_USB3_SHIFT) |
|
||||
(SCFG_USBPWRFAULT_DEDICATED <<
|
||||
SCFG_USBPWRFAULT_USB2_SHIFT) |
|
||||
(SCFG_USBPWRFAULT_SHARED <<
|
||||
SCFG_USBPWRFAULT_USB1_SHIFT);
|
||||
out_be32(&scfg->usbpwrfault_selcr, usb_pwrfault);
|
||||
#endif
|
||||
}
|
||||
|
||||
#ifdef CONFIG_MISC_INIT_R
|
||||
int misc_init_r(void)
|
||||
{
|
||||
config_board_mux();
|
||||
return 0;
|
||||
}
|
||||
#endif
|
||||
|
||||
int ft_board_setup(void *blob, bd_t *bd)
|
||||
{
|
||||
u64 base[CONFIG_NR_DRAM_BANKS];
|
||||
u64 size[CONFIG_NR_DRAM_BANKS];
|
||||
|
||||
/* fixup DT for the two DDR banks */
|
||||
base[0] = gd->bd->bi_dram[0].start;
|
||||
size[0] = gd->bd->bi_dram[0].size;
|
||||
base[1] = gd->bd->bi_dram[1].start;
|
||||
size[1] = gd->bd->bi_dram[1].size;
|
||||
|
||||
fdt_fixup_memory_banks(blob, base, size, 2);
|
||||
ft_cpu_setup(blob, bd);
|
||||
|
||||
#ifdef CONFIG_SYS_DPAA_FMAN
|
||||
fdt_fixup_fman_ethernet(blob);
|
||||
#endif
|
||||
|
||||
return 0;
|
||||
}
|
||||
22
board/freescale/ls1046ardb/ls1046ardb_pbi.cfg
Normal file
22
board/freescale/ls1046ardb/ls1046ardb_pbi.cfg
Normal file
@ -0,0 +1,22 @@
|
||||
#Configure Scratch register
|
||||
09570600 00000000
|
||||
09570604 10000000
|
||||
#Disable CCI barrier tranaction
|
||||
09570178 0000e010
|
||||
09180000 00000008
|
||||
#USB PHY frequency sel
|
||||
09570418 0000009e
|
||||
0957041c 0000009e
|
||||
09570420 0000009e
|
||||
#Serdes SATA
|
||||
09eb1300 80104e20
|
||||
09eb08dc 00502880
|
||||
#PEX gen3 link
|
||||
09570158 00000300
|
||||
89400890 01048000
|
||||
89500890 01048000
|
||||
89600890 01048000
|
||||
#Alt base register
|
||||
09570158 00001000
|
||||
#flush PBI data
|
||||
096100c0 000fffff
|
||||
7
board/freescale/ls1046ardb/ls1046ardb_rcw_emmc.cfg
Normal file
7
board/freescale/ls1046ardb/ls1046ardb_rcw_emmc.cfg
Normal file
@ -0,0 +1,7 @@
|
||||
#PBL preamble and RCW header
|
||||
aa55aa55 01ee0100
|
||||
# RCW
|
||||
0c150010 0e000000 00000000 00000000
|
||||
11335559 40000012 60040000 c1000000
|
||||
00000000 00000000 00000000 00238800
|
||||
20124000 00003000 00000096 00000001
|
||||
7
board/freescale/ls1046ardb/ls1046ardb_rcw_sd.cfg
Normal file
7
board/freescale/ls1046ardb/ls1046ardb_rcw_sd.cfg
Normal file
@ -0,0 +1,7 @@
|
||||
#PBL preamble and RCW header
|
||||
aa55aa55 01ee0100
|
||||
# RCW
|
||||
0c150010 0e000000 00000000 00000000
|
||||
11335559 40005012 60040000 c1000000
|
||||
00000000 00000000 00000000 00238800
|
||||
20124000 00003101 00000096 00000001
|
||||
27
configs/ls1046ardb_emmc_defconfig
Normal file
27
configs/ls1046ardb_emmc_defconfig
Normal file
@ -0,0 +1,27 @@
|
||||
CONFIG_ARM=y
|
||||
CONFIG_TARGET_LS1046ARDB=y
|
||||
CONFIG_DM_SPI=y
|
||||
CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1046a-rdb"
|
||||
CONFIG_SPL=y
|
||||
CONFIG_FIT=y
|
||||
CONFIG_FIT_VERBOSE=y
|
||||
CONFIG_OF_BOARD_SETUP=y
|
||||
CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPL_FSL_PBL,SYS_FSL_DDR4,CONFIG_EMMC_BOOT"
|
||||
CONFIG_SD_BOOT=y
|
||||
CONFIG_BOOTDELAY=10
|
||||
CONFIG_HUSH_PARSER=y
|
||||
# CONFIG_CMD_IMLS is not set
|
||||
CONFIG_CMD_MMC=y
|
||||
CONFIG_CMD_SF=y
|
||||
CONFIG_CMD_I2C=y
|
||||
CONFIG_CMD_DHCP=y
|
||||
CONFIG_CMD_MII=y
|
||||
CONFIG_CMD_PING=y
|
||||
CONFIG_CMD_CACHE=y
|
||||
CONFIG_CMD_EXT2=y
|
||||
CONFIG_CMD_FAT=y
|
||||
CONFIG_OF_CONTROL=y
|
||||
CONFIG_DM=y
|
||||
CONFIG_SPI_FLASH=y
|
||||
CONFIG_SYS_NS16550=y
|
||||
CONFIG_FSL_QSPI=y
|
||||
26
configs/ls1046ardb_qspi_defconfig
Normal file
26
configs/ls1046ardb_qspi_defconfig
Normal file
@ -0,0 +1,26 @@
|
||||
CONFIG_ARM=y
|
||||
CONFIG_TARGET_LS1046ARDB=y
|
||||
CONFIG_DM_SPI=y
|
||||
CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1046a-rdb"
|
||||
CONFIG_FIT=y
|
||||
CONFIG_FIT_VERBOSE=y
|
||||
CONFIG_OF_BOARD_SETUP=y
|
||||
CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4"
|
||||
CONFIG_QSPI_BOOT=y
|
||||
CONFIG_BOOTDELAY=10
|
||||
CONFIG_HUSH_PARSER=y
|
||||
# CONFIG_CMD_IMLS is not set
|
||||
CONFIG_CMD_MMC=y
|
||||
CONFIG_CMD_SF=y
|
||||
CONFIG_CMD_I2C=y
|
||||
CONFIG_CMD_DHCP=y
|
||||
CONFIG_CMD_MII=y
|
||||
CONFIG_CMD_PING=y
|
||||
CONFIG_CMD_CACHE=y
|
||||
CONFIG_CMD_EXT2=y
|
||||
CONFIG_CMD_FAT=y
|
||||
CONFIG_OF_CONTROL=y
|
||||
CONFIG_DM=y
|
||||
CONFIG_SPI_FLASH=y
|
||||
CONFIG_SYS_NS16550=y
|
||||
CONFIG_FSL_QSPI=y
|
||||
27
configs/ls1046ardb_sdcard_defconfig
Normal file
27
configs/ls1046ardb_sdcard_defconfig
Normal file
@ -0,0 +1,27 @@
|
||||
CONFIG_ARM=y
|
||||
CONFIG_TARGET_LS1046ARDB=y
|
||||
CONFIG_DM_SPI=y
|
||||
CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1046a-rdb"
|
||||
CONFIG_SPL=y
|
||||
CONFIG_FIT=y
|
||||
CONFIG_FIT_VERBOSE=y
|
||||
CONFIG_OF_BOARD_SETUP=y
|
||||
CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPL_FSL_PBL,SYS_FSL_DDR4"
|
||||
CONFIG_SD_BOOT=y
|
||||
CONFIG_BOOTDELAY=10
|
||||
CONFIG_HUSH_PARSER=y
|
||||
# CONFIG_CMD_IMLS is not set
|
||||
CONFIG_CMD_MMC=y
|
||||
CONFIG_CMD_SF=y
|
||||
CONFIG_CMD_I2C=y
|
||||
CONFIG_CMD_DHCP=y
|
||||
CONFIG_CMD_MII=y
|
||||
CONFIG_CMD_PING=y
|
||||
CONFIG_CMD_CACHE=y
|
||||
CONFIG_CMD_EXT2=y
|
||||
CONFIG_CMD_FAT=y
|
||||
CONFIG_OF_CONTROL=y
|
||||
CONFIG_DM=y
|
||||
CONFIG_SPI_FLASH=y
|
||||
CONFIG_SYS_NS16550=y
|
||||
CONFIG_FSL_QSPI=y
|
||||
175
include/configs/ls1046a_common.h
Normal file
175
include/configs/ls1046a_common.h
Normal file
@ -0,0 +1,175 @@
|
||||
/*
|
||||
* Copyright 2016 Freescale Semiconductor
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
|
||||
#ifndef __LS1046A_COMMON_H
|
||||
#define __LS1046A_COMMON_H
|
||||
|
||||
#define CONFIG_REMAKE_ELF
|
||||
#define CONFIG_FSL_LAYERSCAPE
|
||||
#define CONFIG_FSL_LSCH2
|
||||
#define CONFIG_LS1046A
|
||||
#define CONFIG_MP
|
||||
#define CONFIG_SYS_FSL_CLK
|
||||
#define CONFIG_GICV2
|
||||
|
||||
#include <asm/arch/config.h>
|
||||
#ifdef CONFIG_SYS_FSL_SRDS_1
|
||||
#define CONFIG_SYS_HAS_SERDES
|
||||
#endif
|
||||
|
||||
/* Link Definitions */
|
||||
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
|
||||
|
||||
#define CONFIG_SUPPORT_RAW_INITRD
|
||||
|
||||
#define CONFIG_SKIP_LOWLEVEL_INIT
|
||||
#define CONFIG_BOARD_EARLY_INIT_F 1
|
||||
|
||||
#define CONFIG_VERY_BIG_RAM
|
||||
#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000
|
||||
#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
|
||||
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
|
||||
#define CONFIG_SYS_DDR_BLOCK2_BASE 0x880000000ULL
|
||||
|
||||
#define CPU_RELEASE_ADDR secondary_boot_func
|
||||
|
||||
/* Generic Timer Definitions */
|
||||
#define COUNTER_FREQUENCY 25000000 /* 25MHz */
|
||||
|
||||
/* Size of malloc() pool */
|
||||
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1024 * 1024)
|
||||
|
||||
/* Serial Port */
|
||||
#define CONFIG_CONS_INDEX 1
|
||||
#define CONFIG_SYS_NS16550_SERIAL
|
||||
#define CONFIG_SYS_NS16550_REG_SIZE 1
|
||||
#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
|
||||
|
||||
#define CONFIG_BAUDRATE 115200
|
||||
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
|
||||
|
||||
/* SD boot SPL */
|
||||
#ifdef CONFIG_SD_BOOT
|
||||
#define CONFIG_SPL_FRAMEWORK
|
||||
#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
|
||||
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
|
||||
#define CONFIG_SPL_LIBCOMMON_SUPPORT
|
||||
#define CONFIG_SPL_LIBGENERIC_SUPPORT
|
||||
#define CONFIG_SPL_ENV_SUPPORT
|
||||
#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
|
||||
#define CONFIG_SPL_WATCHDOG_SUPPORT
|
||||
#define CONFIG_SPL_I2C_SUPPORT
|
||||
#define CONFIG_SPL_SERIAL_SUPPORT
|
||||
#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
|
||||
|
||||
#define CONFIG_SPL_MMC_SUPPORT
|
||||
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x110
|
||||
#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x500
|
||||
#define CONFIG_SPL_TEXT_BASE 0x10000000
|
||||
#define CONFIG_SPL_MAX_SIZE 0x1f000 /* 124 KiB */
|
||||
#define CONFIG_SPL_STACK 0x10020000
|
||||
#define CONFIG_SPL_PAD_TO 0x21000 /* 132 KiB */
|
||||
#define CONFIG_SPL_BSS_START_ADDR 0x8f000000
|
||||
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
|
||||
#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \
|
||||
CONFIG_SPL_BSS_MAX_SIZE)
|
||||
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
|
||||
#define CONFIG_SYS_MONITOR_LEN 0xa0000
|
||||
#endif
|
||||
|
||||
/* I2C */
|
||||
#define CONFIG_SYS_I2C
|
||||
#define CONFIG_SYS_I2C_MXC
|
||||
#define CONFIG_SYS_I2C_MXC_I2C1
|
||||
#define CONFIG_SYS_I2C_MXC_I2C2
|
||||
#define CONFIG_SYS_I2C_MXC_I2C3
|
||||
#define CONFIG_SYS_I2C_MXC_I2C4
|
||||
|
||||
/* Command line configuration */
|
||||
#define CONFIG_CMD_ENV
|
||||
|
||||
/* MMC */
|
||||
#define CONFIG_MMC
|
||||
#ifdef CONFIG_MMC
|
||||
#define CONFIG_FSL_ESDHC
|
||||
#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
|
||||
#define CONFIG_GENERIC_MMC
|
||||
#define CONFIG_DOS_PARTITION
|
||||
#endif
|
||||
|
||||
#define CONFIG_FSL_CAAM /* Enable SEC/CAAM */
|
||||
|
||||
#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
|
||||
|
||||
/* FMan ucode */
|
||||
#define CONFIG_SYS_DPAA_FMAN
|
||||
#ifdef CONFIG_SYS_DPAA_FMAN
|
||||
#define CONFIG_SYS_FM_MURAM_SIZE 0x60000
|
||||
|
||||
#ifdef CONFIG_SD_BOOT
|
||||
/*
|
||||
* PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
|
||||
* about 1MB (2048 blocks), Env is stored after the image, and the env size is
|
||||
* 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080(0x820).
|
||||
*/
|
||||
#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
|
||||
#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820)
|
||||
#else
|
||||
#define CONFIG_SYS_QE_FW_IN_SPIFLASH
|
||||
#define CONFIG_SYS_FMAN_FW_ADDR 0x40300000
|
||||
#define CONFIG_ENV_SPI_BUS 0
|
||||
#define CONFIG_ENV_SPI_CS 0
|
||||
#define CONFIG_ENV_SPI_MAX_HZ 1000000
|
||||
#define CONFIG_ENV_SPI_MODE 0x03
|
||||
#endif
|
||||
#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
|
||||
#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
|
||||
#endif
|
||||
|
||||
/* Miscellaneous configurable options */
|
||||
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
|
||||
#define CONFIG_ARCH_EARLY_INIT_R
|
||||
#define CONFIG_BOARD_LATE_INIT
|
||||
|
||||
#define CONFIG_HWCONFIG
|
||||
#define HWCONFIG_BUFFER_SIZE 128
|
||||
|
||||
/* Initial environment variables */
|
||||
#define CONFIG_EXTRA_ENV_SETTINGS \
|
||||
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
|
||||
"loadaddr=0x80100000\0" \
|
||||
"ramdisk_addr=0x800000\0" \
|
||||
"ramdisk_size=0x2000000\0" \
|
||||
"fdt_high=0xffffffffffffffff\0" \
|
||||
"initrd_high=0xffffffffffffffff\0" \
|
||||
"kernel_start=0x1000000\0" \
|
||||
"kernel_load=0xa0000000\0" \
|
||||
"kernel_size=0x2800000\0" \
|
||||
"console=ttyS0,115200\0" \
|
||||
MTDPARTS_DEFAULT "\0"
|
||||
|
||||
#define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/ram0 " \
|
||||
"earlycon=uart8250,mmio,0x21c0500 " \
|
||||
MTDPARTS_DEFAULT
|
||||
/* Monitor Command Prompt */
|
||||
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
|
||||
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
|
||||
sizeof(CONFIG_SYS_PROMPT) + 16)
|
||||
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */
|
||||
#define CONFIG_SYS_LONGHELP
|
||||
#define CONFIG_CMDLINE_EDITING 1
|
||||
#define CONFIG_AUTO_COMPLETE
|
||||
#define CONFIG_SYS_MAXARGS 64 /* max command args */
|
||||
|
||||
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
|
||||
|
||||
/* Hash command with SHA acceleration supported in hardware */
|
||||
#ifdef CONFIG_FSL_CAAM
|
||||
#define CONFIG_CMD_HASH
|
||||
#define CONFIG_SHA_HW_ACCEL
|
||||
#endif
|
||||
|
||||
#endif /* __LS1046A_COMMON_H */
|
||||
240
include/configs/ls1046ardb.h
Normal file
240
include/configs/ls1046ardb.h
Normal file
@ -0,0 +1,240 @@
|
||||
/*
|
||||
* Copyright 2016 Freescale Semiconductor
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
|
||||
#ifndef __LS1046ARDB_H__
|
||||
#define __LS1046ARDB_H__
|
||||
|
||||
#include "ls1046a_common.h"
|
||||
|
||||
#if defined(CONFIG_FSL_LS_PPA)
|
||||
#define CONFIG_ARMV8_PSCI
|
||||
#define CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT
|
||||
#define CONFIG_SYS_LS_PPA_DRAM_BLOCK_MIN_SIZE (1UL * 1024 * 1024)
|
||||
|
||||
#define CONFIG_SYS_LS_PPA_FW_IN_XIP
|
||||
#ifdef CONFIG_SYS_LS_PPA_FW_IN_XIP
|
||||
#define CONFIG_SYS_LS_PPA_FW_ADDR 0x40500000
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#define CONFIG_DISPLAY_CPUINFO
|
||||
#define CONFIG_DISPLAY_BOARDINFO
|
||||
|
||||
#ifdef CONFIG_SD_BOOT
|
||||
#define CONFIG_SYS_TEXT_BASE 0x82000000
|
||||
#else
|
||||
#define CONFIG_SYS_TEXT_BASE 0x40100000
|
||||
#endif
|
||||
|
||||
#define CONFIG_SYS_CLK_FREQ 100000000
|
||||
#define CONFIG_DDR_CLK_FREQ 100000000
|
||||
|
||||
#define CONFIG_LAYERSCAPE_NS_ACCESS
|
||||
#define CONFIG_MISC_INIT_R
|
||||
|
||||
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
|
||||
/* Physical Memory Map */
|
||||
#define CONFIG_CHIP_SELECTS_PER_CTRL 4
|
||||
#define CONFIG_NR_DRAM_BANKS 2
|
||||
|
||||
#define CONFIG_DDR_SPD
|
||||
#define SPD_EEPROM_ADDRESS 0x51
|
||||
#define CONFIG_SYS_SPD_BUS_NUM 0
|
||||
|
||||
#define CONFIG_DDR_ECC
|
||||
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
|
||||
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
|
||||
#define CONFIG_FSL_DDR_BIST /* enable built-in memory test */
|
||||
#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
|
||||
|
||||
#ifdef CONFIG_RAMBOOT_PBL
|
||||
#define CONFIG_SYS_FSL_PBL_PBI board/freescale/ls1046ardb/ls1046ardb_pbi.cfg
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_SD_BOOT
|
||||
#ifdef CONFIG_EMMC_BOOT
|
||||
#define CONFIG_SYS_FSL_PBL_RCW \
|
||||
board/freescale/ls1046ardb/ls1046ardb_rcw_emmc.cfg
|
||||
#else
|
||||
#define CONFIG_SYS_FSL_PBL_RCW board/freescale/ls1046ardb/ls1046ardb_rcw_sd.cfg
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/* No NOR flash */
|
||||
#define CONFIG_SYS_NO_FLASH
|
||||
|
||||
/* IFC */
|
||||
#define CONFIG_FSL_IFC
|
||||
|
||||
/*
|
||||
* NAND Flash Definitions
|
||||
*/
|
||||
#define CONFIG_NAND_FSL_IFC
|
||||
|
||||
#define CONFIG_SYS_NAND_BASE 0x7e800000
|
||||
#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
|
||||
|
||||
#define CONFIG_SYS_NAND_CSPR_EXT (0x0)
|
||||
#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
|
||||
| CSPR_PORT_SIZE_8 \
|
||||
| CSPR_MSEL_NAND \
|
||||
| CSPR_V)
|
||||
#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024)
|
||||
#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
|
||||
| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
|
||||
| CSOR_NAND_ECC_MODE_8 /* 8-bit ECC */ \
|
||||
| CSOR_NAND_RAL_3 /* RAL = 3 Bytes */ \
|
||||
| CSOR_NAND_PGS_4K /* Page Size = 4K */ \
|
||||
| CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \
|
||||
| CSOR_NAND_PB(64)) /* 64 Pages Per Block */
|
||||
|
||||
#define CONFIG_SYS_NAND_ONFI_DETECTION
|
||||
|
||||
#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x7) | \
|
||||
FTIM0_NAND_TWP(0x18) | \
|
||||
FTIM0_NAND_TWCHT(0x7) | \
|
||||
FTIM0_NAND_TWH(0xa))
|
||||
#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
|
||||
FTIM1_NAND_TWBE(0x39) | \
|
||||
FTIM1_NAND_TRR(0xe) | \
|
||||
FTIM1_NAND_TRP(0x18))
|
||||
#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0xf) | \
|
||||
FTIM2_NAND_TREH(0xa) | \
|
||||
FTIM2_NAND_TWHRE(0x1e))
|
||||
#define CONFIG_SYS_NAND_FTIM3 0x0
|
||||
|
||||
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
|
||||
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
||||
#define CONFIG_MTD_NAND_VERIFY_WRITE
|
||||
#define CONFIG_CMD_NAND
|
||||
|
||||
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
|
||||
|
||||
/*
|
||||
* CPLD
|
||||
*/
|
||||
#define CONFIG_SYS_CPLD_BASE 0x7fb00000
|
||||
#define CPLD_BASE_PHYS CONFIG_SYS_CPLD_BASE
|
||||
|
||||
#define CONFIG_SYS_CPLD_CSPR_EXT (0x0)
|
||||
#define CONFIG_SYS_CPLD_CSPR (CSPR_PHYS_ADDR(CPLD_BASE_PHYS) | \
|
||||
CSPR_PORT_SIZE_8 | \
|
||||
CSPR_MSEL_GPCM | \
|
||||
CSPR_V)
|
||||
#define CONFIG_SYS_CPLD_AMASK IFC_AMASK(64 * 1024)
|
||||
#define CONFIG_SYS_CPLD_CSOR CSOR_NOR_ADM_SHIFT(16)
|
||||
|
||||
/* CPLD Timing parameters for IFC GPCM */
|
||||
#define CONFIG_SYS_CPLD_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
|
||||
FTIM0_GPCM_TEADC(0x0e) | \
|
||||
FTIM0_GPCM_TEAHC(0x0e))
|
||||
#define CONFIG_SYS_CPLD_FTIM1 (FTIM1_GPCM_TACO(0xff) | \
|
||||
FTIM1_GPCM_TRAD(0x3f))
|
||||
#define CONFIG_SYS_CPLD_FTIM2 (FTIM2_GPCM_TCS(0xf) | \
|
||||
FTIM2_GPCM_TCH(0xf) | \
|
||||
FTIM2_GPCM_TWP(0x3E))
|
||||
#define CONFIG_SYS_CPLD_FTIM3 0x0
|
||||
|
||||
/* IFC Timing Params */
|
||||
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
|
||||
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
|
||||
#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
|
||||
#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
|
||||
#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
|
||||
#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
|
||||
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
|
||||
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
|
||||
|
||||
#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_CPLD_CSPR_EXT
|
||||
#define CONFIG_SYS_CSPR2 CONFIG_SYS_CPLD_CSPR
|
||||
#define CONFIG_SYS_AMASK2 CONFIG_SYS_CPLD_AMASK
|
||||
#define CONFIG_SYS_CSOR2 CONFIG_SYS_CPLD_CSOR
|
||||
#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_CPLD_FTIM0
|
||||
#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_CPLD_FTIM1
|
||||
#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_CPLD_FTIM2
|
||||
#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_CPLD_FTIM3
|
||||
|
||||
/* EEPROM */
|
||||
#define CONFIG_ID_EEPROM
|
||||
#define CONFIG_SYS_I2C_EEPROM_NXID
|
||||
#define CONFIG_SYS_EEPROM_BUS_NUM 0
|
||||
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53
|
||||
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
|
||||
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
|
||||
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
|
||||
#define I2C_RETIMER_ADDR 0x18
|
||||
|
||||
/*
|
||||
* Environment
|
||||
*/
|
||||
#define CONFIG_ENV_OVERWRITE
|
||||
|
||||
#if defined(CONFIG_SD_BOOT)
|
||||
#define CONFIG_ENV_IS_IN_MMC
|
||||
#define CONFIG_SYS_MMC_ENV_DEV 0
|
||||
#define CONFIG_ENV_OFFSET (1024 * 1024)
|
||||
#define CONFIG_ENV_SIZE 0x2000
|
||||
#else
|
||||
#define CONFIG_ENV_IS_IN_SPI_FLASH
|
||||
#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
|
||||
#define CONFIG_ENV_OFFSET 0x200000 /* 2MB */
|
||||
#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256KB */
|
||||
#endif
|
||||
|
||||
/* FMan */
|
||||
#ifdef CONFIG_SYS_DPAA_FMAN
|
||||
#define CONFIG_FMAN_ENET
|
||||
#define CONFIG_PHYLIB
|
||||
#define CONFIG_PHYLIB_10G
|
||||
#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
|
||||
|
||||
#define CONFIG_PHY_REALTEK
|
||||
#define CONFIG_PHY_AQUANTIA
|
||||
#define AQR105_IRQ_MASK 0x80000000
|
||||
|
||||
#define RGMII_PHY1_ADDR 0x1
|
||||
#define RGMII_PHY2_ADDR 0x2
|
||||
|
||||
#define SGMII_PHY1_ADDR 0x3
|
||||
#define SGMII_PHY2_ADDR 0x4
|
||||
|
||||
#define FM1_10GEC1_PHY_ADDR 0x0
|
||||
|
||||
#define CONFIG_ETHPRIME "FM1@DTSEC3"
|
||||
#endif
|
||||
|
||||
/* QSPI device */
|
||||
#ifdef CONFIG_FSL_QSPI
|
||||
#define CONFIG_SPI_FLASH_SPANSION
|
||||
#define FSL_QSPI_FLASH_SIZE (1 << 26)
|
||||
#define FSL_QSPI_FLASH_NUM 2
|
||||
#define CONFIG_SPI_FLASH_BAR
|
||||
#endif
|
||||
|
||||
/* SATA */
|
||||
#define CONFIG_LIBATA
|
||||
#define CONFIG_SCSI_AHCI
|
||||
#define CONFIG_SCSI_AHCI_PLAT
|
||||
#define CONFIG_SCSI
|
||||
#define CONFIG_DOS_PARTITION
|
||||
#define CONFIG_BOARD_LATE_INIT
|
||||
|
||||
#define CONFIG_SYS_SATA AHCI_BASE_ADDR
|
||||
|
||||
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
|
||||
#define CONFIG_SYS_SCSI_MAX_LUN 1
|
||||
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
|
||||
CONFIG_SYS_SCSI_MAX_LUN)
|
||||
#define CONFIG_BOOTCOMMAND "sf probe 0:0;sf read $kernel_load" \
|
||||
"$kernel_start $kernel_size;" \
|
||||
"bootm $kernel_load"
|
||||
|
||||
#define MTDPARTS_DEFAULT "mtdparts=1550000.quadspi:1m(rcw)," \
|
||||
"15m(u-boot),48m(kernel.itb);" \
|
||||
"7e800000.flash:16m(nand_uboot)," \
|
||||
"48m(nand_kernel),448m(nand_free)"
|
||||
|
||||
#endif /* __LS1046ARDB_H__ */
|
||||
Loading…
Reference in New Issue
Block a user