From eb5ba3aefdf0f6cbd61684eeb61428f11fa7613c Mon Sep 17 00:00:00 2001 From: Simon Glass Date: Fri, 12 May 2017 21:09:49 -0600 Subject: [PATCH 01/12] i2c: Drop use of CONFIG_I2C_HARD This option is pretty old. It predates CONFIG_SYS_I2C which is itself deprecated in favour of driver model. Disable it for all boards. Also drop I2C options which depend on this. Signed-off-by: Simon Glass --- README | 17 +- arch/arm/include/asm/arch-armada100/config.h | 12 -- board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c | 12 +- board/cm5200/cm5200.c | 32 +--- board/cm5200/cmd_cm5200.c | 32 +--- board/davedenx/aria/aria.c | 3 - board/esd/mecp5123/mecp5123.c | 12 +- board/freescale/mpc5121ads/mpc5121ads.c | 21 --- board/ifm/ac14xx/ac14xx.c | 53 +----- board/renesas/r0p7734/r0p7734.c | 12 +- board/tqc/tqm5200/tqm5200.c | 18 +- configs/MiniFAP_defconfig | 2 - configs/O2D300_defconfig | 1 - configs/O2DNT2_RAMBOOT_defconfig | 1 - configs/O2DNT2_defconfig | 1 - configs/O2D_defconfig | 1 - configs/O2I_defconfig | 1 - configs/O2MNT_O2M110_defconfig | 1 - configs/O2MNT_O2M112_defconfig | 1 - configs/O2MNT_O2M113_defconfig | 1 - configs/O2MNT_defconfig | 1 - configs/O3DNT_defconfig | 1 - configs/TQM5200S_HIGHBOOT_defconfig | 2 - configs/TQM5200S_defconfig | 2 - configs/TQM5200_B_HIGHBOOT_defconfig | 2 - configs/TQM5200_B_defconfig | 2 - configs/TQM5200_STK100_defconfig | 2 - configs/TQM5200_defconfig | 2 - configs/a4m072_defconfig | 1 - configs/ac14xx_defconfig | 1 - configs/ap_sh4a_4a_defconfig | 1 - configs/apx4devkit_defconfig | 2 - configs/aria_defconfig | 1 - configs/aspenite_defconfig | 1 - configs/cam5200_defconfig | 2 - configs/cam5200_niosflash_defconfig | 2 - configs/charon_defconfig | 1 - configs/cm5200_defconfig | 1 - configs/digsy_mtc_RAMBOOT_defconfig | 2 - configs/digsy_mtc_defconfig | 2 - configs/digsy_mtc_rev5_RAMBOOT_defconfig | 2 - configs/digsy_mtc_rev5_defconfig | 2 - configs/fo300_defconfig | 2 - configs/gplugd_defconfig | 1 - configs/ipek01_defconfig | 2 - configs/m28evk_defconfig | 1 - configs/mecp5123_defconfig | 2 - configs/motionpro_defconfig | 2 - configs/mpc5121ads_defconfig | 2 - configs/mpc5121ads_rev2_defconfig | 2 - configs/pcm030_LOWBOOT_defconfig | 2 - configs/pcm030_defconfig | 2 - configs/pdm360ng_defconfig | 2 - configs/r0p7734_defconfig | 1 - configs/v38b_defconfig | 2 - include/common.h | 10 ++ include/configs/M54418TWR.h | 1 - include/configs/TQM5200.h | 64 +------ include/configs/a4m072.h | 20 --- include/configs/ac14xx.h | 18 -- include/configs/ap_sh4a_4a.h | 14 -- include/configs/apx4devkit.h | 6 - include/configs/aria.h | 21 --- include/configs/axs10x.h | 2 +- include/configs/cm5200.h | 12 +- include/configs/digsy_mtc.h | 31 ---- include/configs/ids8313.h | 1 - include/configs/ipek01.h | 23 --- include/configs/jupiter.h | 19 -- include/configs/m28evk.h | 6 - include/configs/manroland/mpc5200-common.h | 176 +++++++++++++++++++ include/configs/mecp5123.h | 18 +- include/configs/motionpro.h | 22 --- include/configs/mpc5121ads.h | 18 -- include/configs/mxs.h | 10 -- include/configs/o2dnt-common.h | 22 --- include/configs/pcm030.h | 31 +--- include/configs/pdm360ng.h | 30 ---- include/configs/r0p7734.h | 14 -- include/configs/s32v234evb.h | 10 -- include/configs/v38b.h | 21 --- 81 files changed, 211 insertions(+), 701 deletions(-) create mode 100644 include/configs/manroland/mpc5200-common.h diff --git a/README b/README index 2ca0102b57..86f0814f79 100644 --- a/README +++ b/README @@ -2213,22 +2213,9 @@ The following options need to be configured: - approved multibus support - better i2c mux support - ** Please consider updating your I2C driver now. ** + ** CONFIG_HARD_I2C is now being removed ** - These enable legacy I2C serial bus commands. Defining - CONFIG_HARD_I2C will include the appropriate I2C driver - for the selected CPU. - - This will allow you to use i2c commands at the u-boot - command line (as long as you set CONFIG_CMD_I2C in - CONFIG_COMMANDS) and communicate with i2c based realtime - clock chips. See common/cmd_i2c.c for a description of the - command line interface. - - CONFIG_HARD_I2C selects a hardware I2C controller. - - There are several other quantities that must also be - defined when you define CONFIG_HARD_I2C. +----under removal: In both cases you will need to define CONFIG_SYS_I2C_SPEED to be the frequency (in Hz) at which you wish your i2c bus diff --git a/arch/arm/include/asm/arch-armada100/config.h b/arch/arm/include/asm/arch-armada100/config.h index 6ebc759f4b..113e1c73f3 100644 --- a/arch/arm/include/asm/arch-armada100/config.h +++ b/arch/arm/include/asm/arch-armada100/config.h @@ -24,17 +24,5 @@ #define MV_UART_CONSOLE_BASE ARMD1_UART1_BASE #define CONFIG_SYS_NS16550_IER (1 << 6) /* Bit 6 in UART_IER register represents UART Unit Enable */ -/* - * I2C definition - */ -#ifdef CONFIG_CMD_I2C -#define CONFIG_I2C_MV 1 -#define CONFIG_MV_I2C_NUM 2 -#define CONFIG_I2C_MULTI_BUS 1 -#define CONFIG_MV_I2C_REG {0xd4011000, 0xd4025000} -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_SPEED 0 -#define CONFIG_SYS_I2C_SLAVE 0xfe -#endif #endif /* _ARMD1_CONFIG_H */ diff --git a/board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c b/board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c index 31418a1f96..9205c22e0b 100644 --- a/board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c +++ b/board/alphaproject/ap_sh4a_4a/ap_sh4a_4a.c @@ -156,17 +156,7 @@ int board_init(void) int board_late_init(void) { - u8 mac[6]; - - /* Read Mac Address and set*/ - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); - i2c_set_bus_num(CONFIG_SYS_I2C_MODULE); - - /* Read MAC address */ - i2c_read(0x50, 0x0, 0, mac, 6); - - if (is_valid_ethaddr(mac)) - eth_setenv_enetaddr("ethaddr", mac); + printf("Cannot use I2C to get MAC address\n"); return 0; } diff --git a/board/cm5200/cm5200.c b/board/cm5200/cm5200.c index 7b862355c8..2f55191caf 100644 --- a/board/cm5200/cm5200.c +++ b/board/cm5200/cm5200.c @@ -161,14 +161,7 @@ int dram_init(void) */ static void read_hw_id(hw_id_t hw_id) { - int i; - for (i = 0; i < HW_ID_ELEM_COUNT; ++i) - if (i2c_read(CONFIG_SYS_I2C_EEPROM, - hw_id_format[i].offset, - 2, - (uchar *)&hw_id[i][0], - hw_id_format[i].length) != 0) - printf("ERROR: can't read HW ID from EEPROM\n"); + printf("ERROR: can't read HW ID from EEPROM\n"); } @@ -221,7 +214,7 @@ static void compose_module_name(hw_id_t hw_id, char *buf) strcat(buf, tmp); } - +#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT) /* * Compose string with hostname. * buf is assumed to have enough space, and be null-terminated. @@ -237,7 +230,7 @@ static void compose_hostname(hw_id_t hw_id, char *buf) *p = tolower(*p); } - +#endif #ifdef CONFIG_OF_BOARD_SETUP /* @@ -270,15 +263,6 @@ int checkboard(void) hw_id_t hw_id_tmp; char module_name_tmp[MODULE_NAME_MAXLEN] = ""; - /* - * We need I2C to access HW ID data from EEPROM, so we call i2c_init() - * here despite the fact that it will be called again later on. We - * also use a little trick to silence I2C-related output. - */ - gd->flags |= GD_FLG_SILENT; - i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); - gd->flags &= ~GD_FLG_SILENT; - read_hw_id(hw_id_tmp); identify_module(hw_id_tmp); /* this sets gd->board_type */ compose_module_name(hw_id_tmp, module_name_tmp); @@ -334,16 +318,16 @@ int misc_init_r(void) " device at address %02X:%04X\n", CONFIG_SYS_I2C_EEPROM, CONFIG_MAC_OFFSET); } + hostname[0] = 0x00; + /* set the hostname appropriate to the module we're running on */ + compose_hostname(hw_id, hostname); + setenv("hostname", hostname); + #endif /* defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT) */ if (!getenv("ethaddr")) printf(LOG_PREFIX "MAC address not set, networking is not " "operational\n"); - /* set the hostname appropriate to the module we're running on */ - hostname[0] = 0x00; - compose_hostname(hw_id, hostname); - setenv("hostname", hostname); - return 0; } #endif /* CONFIG_MISC_INIT_R */ diff --git a/board/cm5200/cmd_cm5200.c b/board/cm5200/cmd_cm5200.c index 9c40ad7b2a..60097dc8c7 100644 --- a/board/cm5200/cmd_cm5200.c +++ b/board/cm5200/cmd_cm5200.c @@ -13,34 +13,6 @@ #ifdef CONFIG_CMD_BSP -static int do_i2c_test(char * const argv[]) -{ - unsigned char temp, temp1; - - printf("Starting I2C Test\n" - "Please set Jumper:\nI2C SDA 2-3\nI2C SCL 2-3\n\n" - "Please press any key to start\n\n"); - getc(); - - temp = 0xf0; /* set io 0-4 as output */ - i2c_write(CONFIG_SYS_I2C_IO, 3, 1, (uchar *)&temp, 1); - - printf("Press I2C4-7. LED I2C0-3 should have the same state\n\n" - "Press any key to stop\n\n"); - - while (!tstc()) { - i2c_read(CONFIG_SYS_I2C_IO, 0, 1, (uchar *)&temp, 1); - temp1 = (temp >> 4) & 0x03; - temp1 |= (temp >> 3) & 0x08; /* S302 -> LED303 */ - temp1 |= (temp >> 5) & 0x04; /* S303 -> LED302 */ - temp = temp1; - i2c_write(CONFIG_SYS_I2C_IO, 1, 1, (uchar *)&temp, 1); - } - getc(); - - return 0; -} - static int do_usb_test(char * const argv[]) { int i; @@ -387,9 +359,7 @@ static int cmd_fkt(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) switch (argc) { case 2: - if (strncmp(argv[1], "i2c", 3) == 0) - rcode = do_i2c_test(argv); - else if (strncmp(argv[1], "led", 3) == 0) + if (strncmp(argv[1], "led", 3) == 0) rcode = do_led_test(argv); else if (strncmp(argv[1], "usb", 3) == 0) rcode = do_usb_test(argv); diff --git a/board/davedenx/aria/aria.c b/board/davedenx/aria/aria.c index e3441cad4e..e389819e9d 100644 --- a/board/davedenx/aria/aria.c +++ b/board/davedenx/aria/aria.c @@ -29,9 +29,6 @@ int misc_init_r(void) { u32 tmp; - /* we use I2C-2 for on-board eeprom */ - i2c_set_bus_num(2); - tmp = in_be32((u32*)CONFIG_SYS_ARIA_FPGA_BASE); printf("FPGA: %u-%u.%u.%u\n", (tmp & 0xFF000000) >> 24, diff --git a/board/esd/mecp5123/mecp5123.c b/board/esd/mecp5123/mecp5123.c index 66dc407bae..78a6b66110 100644 --- a/board/esd/mecp5123/mecp5123.c +++ b/board/esd/mecp5123/mecp5123.c @@ -18,17 +18,7 @@ DECLARE_GLOBAL_DATA_PTR; int eeprom_write_enable(unsigned dev_addr, int state) { - volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR; - - if (dev_addr != CONFIG_SYS_I2C_EEPROM_ADDR) - return -1; - - if (state == 0) - setbits_be32(&im->gpio.gpdat, 0x00100000); - else - clrbits_be32(&im->gpio.gpdat, 0x00100000); - - return 0; + return -ENOSYS; } int board_early_init_f(void) diff --git a/board/freescale/mpc5121ads/mpc5121ads.c b/board/freescale/mpc5121ads/mpc5121ads.c index f87579f193..d729056fd0 100644 --- a/board/freescale/mpc5121ads/mpc5121ads.c +++ b/board/freescale/mpc5121ads/mpc5121ads.c @@ -174,27 +174,6 @@ int dram_init(void) int misc_init_r(void) { - u8 tmp_val; - - /* Using this for DIU init before the driver in linux takes over - * Enable the TFP410 Encoder (I2C address 0x38) - */ - - i2c_set_bus_num(2); - tmp_val = 0xBF; - i2c_write(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val)); - /* Verify if enabled */ - tmp_val = 0; - i2c_read(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val)); - debug("DVI Encoder Read: 0x%02x\n", tmp_val); - - tmp_val = 0x10; - i2c_write(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val)); - /* Verify if enabled */ - tmp_val = 0; - i2c_read(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val)); - debug("DVI Encoder Read: 0x%02x\n", tmp_val); - return 0; } diff --git a/board/ifm/ac14xx/ac14xx.c b/board/ifm/ac14xx/ac14xx.c index 348613736d..cd79e804a0 100644 --- a/board/ifm/ac14xx/ac14xx.c +++ b/board/ifm/ac14xx/ac14xx.c @@ -17,7 +17,6 @@ #include #endif -static int eeprom_diag; static int mac_diag; static int gpio_diag; @@ -136,7 +135,6 @@ struct __attribute__ ((__packed__)) eeprom_layout { #define HW_COMP_MAINCPU 2 static struct eeprom_layout eeprom_content; -static int eeprom_was_read; /* has_been_read */ static int eeprom_is_valid; static int eeprom_version; @@ -153,53 +151,7 @@ static int eeprom_version; static int read_eeprom(void) { - int eeprom_datalen; - int ret; - - if (eeprom_was_read) - return 0; - - eeprom_is_valid = 0; - ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, - CONFIG_SYS_I2C_EEPROM_ADDR_LEN, - (uchar *)&eeprom_content, sizeof(eeprom_content)); - if (eeprom_diag) { - printf("DIAG: %s() read rc[%d], size[%d]\n", - __func__, ret, sizeof(eeprom_content)); - } - - if (ret != 0) - return -1; - - eeprom_was_read = 1; - - /* - * check validity of EEPROM content - * (check version, length, optionally checksum) - */ - eeprom_is_valid = 1; - eeprom_datalen = get_eeprom_field_int(eeprom_content.len); - eeprom_version = get_eeprom_field_int(eeprom_content.version); - - if (eeprom_diag) { - printf("DIAG: %s() magic[%c%c%c] len[%d] ver[%d] type[%d]\n", - __func__, eeprom_content.magic[0], - eeprom_content.magic[1], eeprom_content.magic[2], - eeprom_datalen, eeprom_version, eeprom_content.type); - } - if (strncmp(eeprom_content.magic, "ifm", strlen("ifm")) != 0) - eeprom_is_valid = 0; - if (eeprom_datalen < sizeof(struct eeprom_layout) - 5) - eeprom_is_valid = 0; - if ((eeprom_version != 1) && (eeprom_version != 2)) - eeprom_is_valid = 0; - if (eeprom_content.type != HW_COMP_MAINCPU) - eeprom_is_valid = 0; - - if (eeprom_diag) - printf("DIAG: %s() valid[%d]\n", __func__, eeprom_is_valid); - - return ret; + return -ENOSYS; } int mac_read_from_eeprom(void) @@ -324,9 +276,6 @@ int misc_init_r(void) char *s; int want_recovery; - /* we use bus I2C-0 for the on-board eeprom */ - i2c_set_bus_num(0); - /* setup GPIO directions and initial values */ gpio_configure(); diff --git a/board/renesas/r0p7734/r0p7734.c b/board/renesas/r0p7734/r0p7734.c index 360e0a1a6f..d0b4537513 100644 --- a/board/renesas/r0p7734/r0p7734.c +++ b/board/renesas/r0p7734/r0p7734.c @@ -44,17 +44,7 @@ int board_init(void) int board_late_init(void) { - u8 mac[6]; - - /* Read Mac Address and set*/ - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); - i2c_set_bus_num(CONFIG_SYS_I2C_MODULE); - - /* Read MAC address */ - i2c_read(0x50, 0x10, 0, mac, 6); - - if (is_valid_ethaddr(mac)) - eth_setenv_enetaddr("ethaddr", mac); + printf("Cannot get MAC address from I2C\n"); return 0; } diff --git a/board/tqc/tqm5200/tqm5200.c b/board/tqc/tqm5200/tqm5200.c index 92db093dbf..c48ab11fc4 100644 --- a/board/tqc/tqm5200/tqm5200.c +++ b/board/tqc/tqm5200/tqm5200.c @@ -486,20 +486,14 @@ int board_early_init_f (void) static int tfp410_read_reg(int reg, uchar *buf) { - if (i2c_read(CONFIG_SYS_TFP410_ADDR, reg, 1, buf, 1) != 0) { - puts ("Error reading the chip.\n"); - return 1; - } - return 0; + puts("Error reading the chip.\n"); + return -ENOSYS; } static int tfp410_write_reg(int reg, uchar buf) { - if (i2c_write(CONFIG_SYS_TFP410_ADDR, reg, 1, &buf, 1) != 0) { - puts ("Error writing the chip.\n"); - return 1; - } - return 0; + puts("Error writing the chip.\n"); + return -ENOSYS; } typedef struct _tfp410_config { @@ -525,12 +519,9 @@ static int charon_last_stage_init(void) { volatile struct mpc5xxx_lpb *lpb = (struct mpc5xxx_lpb *) MPC5XXX_LPB; - int oldbus = i2c_get_bus_num(); uchar buf; int i = 0; - i2c_set_bus_num(CONFIG_SYS_TFP410_BUS); - /* check version */ if (tfp410_read_reg(TFP410_REG_DEV_ID_H, &buf) != 0) return -1; @@ -551,7 +542,6 @@ static int charon_last_stage_init(void) i++; } printf("TFP410 initialized.\n"); - i2c_set_bus_num(oldbus); /* set deadcycle for cs3 to 0 */ setbits_be32(&lpb->cs_deadcycle, 0xffffcfff); diff --git a/configs/MiniFAP_defconfig b/configs/MiniFAP_defconfig index 7d719f81f5..02ca577e28 100644 --- a/configs/MiniFAP_defconfig +++ b/configs/MiniFAP_defconfig @@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -19,7 +18,6 @@ CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BMP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/O2D300_defconfig b/configs/O2D300_defconfig index 38101f05df..c0e9541b87 100644 --- a/configs/O2D300_defconfig +++ b/configs/O2D300_defconfig @@ -4,7 +4,6 @@ CONFIG_TARGET_O2D300=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O2DNT2_RAMBOOT_defconfig b/configs/O2DNT2_RAMBOOT_defconfig index 83006e5582..8cff44cf36 100644 --- a/configs/O2DNT2_RAMBOOT_defconfig +++ b/configs/O2DNT2_RAMBOOT_defconfig @@ -8,7 +8,6 @@ CONFIG_HUSH_PARSER=y CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press password to stop\n" CONFIG_AUTOBOOT_STOP_STR="++++++++++" -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O2DNT2_defconfig b/configs/O2DNT2_defconfig index 4202d85203..f29abb83bc 100644 --- a/configs/O2DNT2_defconfig +++ b/configs/O2DNT2_defconfig @@ -7,7 +7,6 @@ CONFIG_HUSH_PARSER=y CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press password to stop\n" CONFIG_AUTOBOOT_STOP_STR="++++++++++" -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O2D_defconfig b/configs/O2D_defconfig index b84a1c8839..534cfe12e2 100644 --- a/configs/O2D_defconfig +++ b/configs/O2D_defconfig @@ -4,7 +4,6 @@ CONFIG_TARGET_O2D=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O2I_defconfig b/configs/O2I_defconfig index efcc769ff4..acf42abe29 100644 --- a/configs/O2I_defconfig +++ b/configs/O2I_defconfig @@ -4,7 +4,6 @@ CONFIG_TARGET_O2I=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O2MNT_O2M110_defconfig b/configs/O2MNT_O2M110_defconfig index abdc53df21..de647c76b9 100644 --- a/configs/O2MNT_O2M110_defconfig +++ b/configs/O2MNT_O2M110_defconfig @@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M110\"" CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O2MNT_O2M112_defconfig b/configs/O2MNT_O2M112_defconfig index 06089fe3cf..b243e9cc0e 100644 --- a/configs/O2MNT_O2M112_defconfig +++ b/configs/O2MNT_O2M112_defconfig @@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M112\"" CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O2MNT_O2M113_defconfig b/configs/O2MNT_O2M113_defconfig index 1ea3f3a09b..1584058289 100644 --- a/configs/O2MNT_O2M113_defconfig +++ b/configs/O2MNT_O2M113_defconfig @@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M113\"" CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O2MNT_defconfig b/configs/O2MNT_defconfig index 0209085605..20bd31466e 100644 --- a/configs/O2MNT_defconfig +++ b/configs/O2MNT_defconfig @@ -4,7 +4,6 @@ CONFIG_TARGET_O2MNT=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/O3DNT_defconfig b/configs/O3DNT_defconfig index 5ce4140859..ea769e7edc 100644 --- a/configs/O3DNT_defconfig +++ b/configs/O3DNT_defconfig @@ -4,7 +4,6 @@ CONFIG_TARGET_O3DNT=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/TQM5200S_HIGHBOOT_defconfig b/configs/TQM5200S_HIGHBOOT_defconfig index d0cd50a63c..d07596add0 100644 --- a/configs/TQM5200S_HIGHBOOT_defconfig +++ b/configs/TQM5200S_HIGHBOOT_defconfig @@ -7,7 +7,6 @@ CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -15,7 +14,6 @@ CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/TQM5200S_defconfig b/configs/TQM5200S_defconfig index 5324a9a11c..af3225554b 100644 --- a/configs/TQM5200S_defconfig +++ b/configs/TQM5200S_defconfig @@ -7,7 +7,6 @@ CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -15,7 +14,6 @@ CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/TQM5200_B_HIGHBOOT_defconfig b/configs/TQM5200_B_HIGHBOOT_defconfig index 2f933e6cab..37d6767f28 100644 --- a/configs/TQM5200_B_HIGHBOOT_defconfig +++ b/configs/TQM5200_B_HIGHBOOT_defconfig @@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -19,7 +18,6 @@ CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BMP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/TQM5200_B_defconfig b/configs/TQM5200_B_defconfig index f204484f59..5e0cf9ea47 100644 --- a/configs/TQM5200_B_defconfig +++ b/configs/TQM5200_B_defconfig @@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -19,7 +18,6 @@ CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BMP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/TQM5200_STK100_defconfig b/configs/TQM5200_STK100_defconfig index db9bb8a30d..7b4b030d74 100644 --- a/configs/TQM5200_STK100_defconfig +++ b/configs/TQM5200_STK100_defconfig @@ -10,7 +10,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -19,7 +18,6 @@ CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BMP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/TQM5200_defconfig b/configs/TQM5200_defconfig index eec60f1be4..4792639653 100644 --- a/configs/TQM5200_defconfig +++ b/configs/TQM5200_defconfig @@ -9,7 +9,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -18,7 +17,6 @@ CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BMP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/a4m072_defconfig b/configs/a4m072_defconfig index ce5edcbf01..0054d4cddb 100644 --- a/configs/a4m072_defconfig +++ b/configs/a4m072_defconfig @@ -7,7 +7,6 @@ CONFIG_HUSH_PARSER=y CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="autoboot in %d seconds\n" CONFIG_AUTOBOOT_DELAY_STR="asdfg" -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y diff --git a/configs/ac14xx_defconfig b/configs/ac14xx_defconfig index e3b7793e04..930ec8acf2 100644 --- a/configs/ac14xx_defconfig +++ b/configs/ac14xx_defconfig @@ -5,7 +5,6 @@ CONFIG_FIT=y CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_PROMPT="ac14xx> " CONFIG_CMD_ASKENV=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/ap_sh4a_4a_defconfig b/configs/ap_sh4a_4a_defconfig index 75cf53fe21..41c8be9120 100644 --- a/configs/ap_sh4a_4a_defconfig +++ b/configs/ap_sh4a_4a_defconfig @@ -13,7 +13,6 @@ CONFIG_VERSION_VARIABLE=y # CONFIG_CMD_ENV_EXISTS is not set # CONFIG_CMD_LOADB is not set # CONFIG_CMD_LOADS is not set -CONFIG_CMD_I2C=y # CONFIG_CMD_FPGA is not set # CONFIG_CMD_ECHO is not set # CONFIG_CMD_ITEST is not set diff --git a/configs/apx4devkit_defconfig b/configs/apx4devkit_defconfig index e2061a2cce..5c30fe3ce7 100644 --- a/configs/apx4devkit_defconfig +++ b/configs/apx4devkit_defconfig @@ -14,14 +14,12 @@ CONFIG_HUSH_PARSER=y # CONFIG_CMD_IMLS is not set # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_CACHE=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_UBI=y diff --git a/configs/aria_defconfig b/configs/aria_defconfig index 963661ab2d..0f1432f9a8 100644 --- a/configs/aria_defconfig +++ b/configs/aria_defconfig @@ -5,7 +5,6 @@ CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y diff --git a/configs/aspenite_defconfig b/configs/aspenite_defconfig index 26654426ed..0ac39eabd2 100644 --- a/configs/aspenite_defconfig +++ b/configs/aspenite_defconfig @@ -6,7 +6,6 @@ CONFIG_BOOTDELAY=3 CONFIG_BOARD_EARLY_INIT_F=y # CONFIG_CMD_IMLS is not set # CONFIG_CMD_FLASH is not set -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set # CONFIG_CMD_NET is not set # CONFIG_CMD_NFS is not set diff --git a/configs/cam5200_defconfig b/configs/cam5200_defconfig index 92985ab3d6..46a24f56ab 100644 --- a/configs/cam5200_defconfig +++ b/configs/cam5200_defconfig @@ -7,14 +7,12 @@ CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_MAC_PARTITION=y CONFIG_DOS_PARTITION=y CONFIG_ISO_PARTITION=y diff --git a/configs/cam5200_niosflash_defconfig b/configs/cam5200_niosflash_defconfig index 32bc58ee9b..6b9877ff21 100644 --- a/configs/cam5200_niosflash_defconfig +++ b/configs/cam5200_niosflash_defconfig @@ -7,14 +7,12 @@ CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_MAC_PARTITION=y CONFIG_DOS_PARTITION=y CONFIG_ISO_PARTITION=y diff --git a/configs/charon_defconfig b/configs/charon_defconfig index ec22a6368f..8a1429037a 100644 --- a/configs/charon_defconfig +++ b/configs/charon_defconfig @@ -9,7 +9,6 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y diff --git a/configs/cm5200_defconfig b/configs/cm5200_defconfig index 7d8d01aaaa..d3369f4455 100644 --- a/configs/cm5200_defconfig +++ b/configs/cm5200_defconfig @@ -6,7 +6,6 @@ CONFIG_BOOTDELAY=5 CONFIG_SILENT_CONSOLE=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y diff --git a/configs/digsy_mtc_RAMBOOT_defconfig b/configs/digsy_mtc_RAMBOOT_defconfig index 0d11eec75a..86b2b0d804 100644 --- a/configs/digsy_mtc_RAMBOOT_defconfig +++ b/configs/digsy_mtc_RAMBOOT_defconfig @@ -13,7 +13,6 @@ CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n" CONFIG_AUTOBOOT_DELAY_STR="d" CONFIG_AUTOBOOT_STOP_STR=" " CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -21,7 +20,6 @@ CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_BMP=y CONFIG_CMD_CACHE=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/digsy_mtc_defconfig b/configs/digsy_mtc_defconfig index dc17ab4406..85b7f850f7 100644 --- a/configs/digsy_mtc_defconfig +++ b/configs/digsy_mtc_defconfig @@ -11,7 +11,6 @@ CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="autoboot in %d seconds\n" CONFIG_AUTOBOOT_DELAY_STR=" " CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -19,7 +18,6 @@ CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_BMP=y CONFIG_CMD_CACHE=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/digsy_mtc_rev5_RAMBOOT_defconfig b/configs/digsy_mtc_rev5_RAMBOOT_defconfig index 4ab11c755b..7ec8650aca 100644 --- a/configs/digsy_mtc_rev5_RAMBOOT_defconfig +++ b/configs/digsy_mtc_rev5_RAMBOOT_defconfig @@ -13,7 +13,6 @@ CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n" CONFIG_AUTOBOOT_DELAY_STR="d" CONFIG_AUTOBOOT_STOP_STR=" " CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -21,7 +20,6 @@ CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_BMP=y CONFIG_CMD_CACHE=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/digsy_mtc_rev5_defconfig b/configs/digsy_mtc_rev5_defconfig index 1f3f3c8bb6..b4b8533063 100644 --- a/configs/digsy_mtc_rev5_defconfig +++ b/configs/digsy_mtc_rev5_defconfig @@ -13,7 +13,6 @@ CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n" CONFIG_AUTOBOOT_DELAY_STR="d" CONFIG_AUTOBOOT_STOP_STR=" " CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -21,7 +20,6 @@ CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_BMP=y CONFIG_CMD_CACHE=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/fo300_defconfig b/configs/fo300_defconfig index b4f334a436..00418153be 100644 --- a/configs/fo300_defconfig +++ b/configs/fo300_defconfig @@ -12,7 +12,6 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y @@ -21,7 +20,6 @@ CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_BMP=y CONFIG_CMD_BSP=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y diff --git a/configs/gplugd_defconfig b/configs/gplugd_defconfig index 97bb976803..f44b68dae8 100644 --- a/configs/gplugd_defconfig +++ b/configs/gplugd_defconfig @@ -6,7 +6,6 @@ CONFIG_BOOTDELAY=3 CONFIG_BOARD_EARLY_INIT_F=y # CONFIG_CMD_IMLS is not set # CONFIG_CMD_FLASH is not set -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_FPGA is not set # CONFIG_CMD_SETEXPR is not set diff --git a/configs/ipek01_defconfig b/configs/ipek01_defconfig index cac9326b6c..690bc0f461 100644 --- a/configs/ipek01_defconfig +++ b/configs/ipek01_defconfig @@ -7,13 +7,11 @@ CONFIG_BOOTDELAY=5 # CONFIG_CONSOLE_MUX is not set CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_LOOPW=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_BMP=y -CONFIG_CMD_DATE=y CONFIG_CMD_FAT=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y diff --git a/configs/m28evk_defconfig b/configs/m28evk_defconfig index 6acbd77d5f..0ab7f6bb3c 100644 --- a/configs/m28evk_defconfig +++ b/configs/m28evk_defconfig @@ -22,7 +22,6 @@ CONFIG_CMD_GREPENV=y CONFIG_CMD_MMC=y CONFIG_CMD_SF=y CONFIG_CMD_SPI=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y CONFIG_CMD_GPIO=y CONFIG_CMD_DHCP=y diff --git a/configs/mecp5123_defconfig b/configs/mecp5123_defconfig index ebf5415464..db52077e1a 100644 --- a/configs/mecp5123_defconfig +++ b/configs/mecp5123_defconfig @@ -6,12 +6,10 @@ CONFIG_BOOTDELAY=5 CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y -CONFIG_CMD_DATE=y CONFIG_CMD_FAT=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y diff --git a/configs/motionpro_defconfig b/configs/motionpro_defconfig index 91384a6259..5040ea5742 100644 --- a/configs/motionpro_defconfig +++ b/configs/motionpro_defconfig @@ -8,12 +8,10 @@ CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press \"\" to stop\n" CONFIG_AUTOBOOT_STOP_STR="\x1b\x1b" CONFIG_CMD_ASKENV=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y -CONFIG_CMD_DATE=y CONFIG_CMD_FAT=y CONFIG_CMD_BEDBUG=y CONFIG_LED_STATUS=y diff --git a/configs/mpc5121ads_defconfig b/configs/mpc5121ads_defconfig index c0af8127b5..47c4e5ace7 100644 --- a/configs/mpc5121ads_defconfig +++ b/configs/mpc5121ads_defconfig @@ -6,13 +6,11 @@ CONFIG_BOOTDELAY=5 CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_MAC_PARTITION=y diff --git a/configs/mpc5121ads_rev2_defconfig b/configs/mpc5121ads_rev2_defconfig index ad46e02e94..ef700d0773 100644 --- a/configs/mpc5121ads_rev2_defconfig +++ b/configs/mpc5121ads_rev2_defconfig @@ -7,13 +7,11 @@ CONFIG_BOOTDELAY=5 CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_MAC_PARTITION=y diff --git a/configs/pcm030_LOWBOOT_defconfig b/configs/pcm030_LOWBOOT_defconfig index d19908ca8f..2933326e5d 100644 --- a/configs/pcm030_LOWBOOT_defconfig +++ b/configs/pcm030_LOWBOOT_defconfig @@ -4,11 +4,9 @@ CONFIG_TARGET_PCM030=y CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="SYS_TEXT_BASE=0xFF000000" CONFIG_BOOTDELAY=3 -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y -CONFIG_CMD_DATE=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y CONFIG_USB=y diff --git a/configs/pcm030_defconfig b/configs/pcm030_defconfig index ef5c85888c..ff9f4e9f4f 100644 --- a/configs/pcm030_defconfig +++ b/configs/pcm030_defconfig @@ -4,11 +4,9 @@ CONFIG_TARGET_PCM030=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=3 CONFIG_SYS_PROMPT="uboot> " -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y -CONFIG_CMD_DATE=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y CONFIG_USB=y diff --git a/configs/pdm360ng_defconfig b/configs/pdm360ng_defconfig index f45a90caf9..4ef0df1aa8 100644 --- a/configs/pdm360ng_defconfig +++ b/configs/pdm360ng_defconfig @@ -10,13 +10,11 @@ CONFIG_SILENT_CONSOLE=y # CONFIG_CONSOLE_MUX is not set CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y -CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_BMP=y -CONFIG_CMD_DATE=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y # CONFIG_PCI is not set diff --git a/configs/r0p7734_defconfig b/configs/r0p7734_defconfig index c5c3d52718..91b08dc24f 100644 --- a/configs/r0p7734_defconfig +++ b/configs/r0p7734_defconfig @@ -13,7 +13,6 @@ CONFIG_VERSION_VARIABLE=y # CONFIG_CMD_ENV_EXISTS is not set # CONFIG_CMD_LOADB is not set # CONFIG_CMD_LOADS is not set -CONFIG_CMD_I2C=y # CONFIG_CMD_FPGA is not set # CONFIG_CMD_ECHO is not set # CONFIG_CMD_ITEST is not set diff --git a/configs/v38b_defconfig b/configs/v38b_defconfig index db4c47c3d2..18dc039d93 100644 --- a/configs/v38b_defconfig +++ b/configs/v38b_defconfig @@ -3,13 +3,11 @@ CONFIG_MPC5xxx=y CONFIG_TARGET_V38B=y CONFIG_BOOTDELAY=3 CONFIG_BOARD_EARLY_INIT_F=y -CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y -CONFIG_CMD_DATE=y CONFIG_CMD_FAT=y CONFIG_CMD_DIAG=y CONFIG_MAC_PARTITION=y diff --git a/include/common.h b/include/common.h index 83e4037a86..45f190a600 100644 --- a/include/common.h +++ b/include/common.h @@ -499,9 +499,19 @@ void reset_phy (void); void fdc_hw_init (void); /* $(BOARD)/eeprom.c */ +#ifdef CONFIG_CMD_EEPROM void eeprom_init (int bus); int eeprom_read (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt); int eeprom_write (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt); +#else +/* + * Some EEPROM code is depecated because it used the legacy I2C interface. Add + * some macros here so we don't have to touch every one of those uses + */ +#define eeprom_init(bus) +#define eeprom_read(dev_addr, offset, buffer, cnt) ((void)-ENOSYS) +#define eeprom_write(dev_addr, offset, buffer, cnt) ((void)-ENOSYS) +#endif /* * Set this up regardless of board diff --git a/include/configs/M54418TWR.h b/include/configs/M54418TWR.h index 1817571efe..7b162cccef 100644 --- a/include/configs/M54418TWR.h +++ b/include/configs/M54418TWR.h @@ -166,7 +166,6 @@ /* I2c */ #undef CONFIG_SYS_FSL_I2C -#undef CONFIG_HARD_I2C /* I2C with hardware support */ #undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SPEED 80000 diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h index 13f4ef67e1..19e0b1be1b 100644 --- a/include/configs/TQM5200.h +++ b/include/configs/TQM5200.h @@ -124,8 +124,7 @@ #ifndef CONFIG_CAM5200 /* POST support */ #define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ - CONFIG_SYS_POST_CPU | \ - CONFIG_SYS_POST_I2C) + CONFIG_SYS_POST_CPU) #endif #ifdef CONFIG_POST @@ -144,7 +143,6 @@ /* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_REGINFO @@ -278,54 +276,6 @@ #define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */ #endif -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#ifdef CONFIG_TQM5200_REV100 -#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 for rev. 100 board */ -#else -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 for all other revs */ -#endif - -/* - * I2C clock frequency - * - * Please notice, that the resulting clock frequency could differ from the - * configured value. This is because the I2C clock is derived from system - * clock over a frequency divider with only a few divider values. U-Boot - * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated - * approximation allways lies below the configured value, never above. - */ -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work - * also). For other EEPROMs configuration should be verified. On Mini-FAP the - * EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the - * same configuration could be used. - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 - -/* - * HW-Monitor configuration on Mini-FAP - */ -#if defined (CONFIG_MINIFAP) -#define CONFIG_SYS_I2C_HWMON_ADDR 0x2C -#endif - -/* List of I2C addresses to be verified by POST */ -#if defined (CONFIG_MINIFAP) -#undef CONFIG_SYS_POST_I2C_ADDRS -#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_EEPROM_ADDR, \ - CONFIG_SYS_I2C_HWMON_ADDR, \ - CONFIG_SYS_I2C_SLAVE} -#endif - /* * Flash configuration */ @@ -544,18 +494,6 @@ #endif #endif -/* - * RTC configuration - */ -#if defined (CONFIG_STK52XX) && !defined (CONFIG_STK52XX_REV100) -# define CONFIG_RTC_M41T11 1 -# define CONFIG_SYS_I2C_RTC_ADDR 0x68 -# define CONFIG_SYS_M41T11_BASE_YEAR 1900 /* because Linux uses the same base - year */ -#else -# define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */ -#endif - /* * Miscellaneous configurable options */ diff --git a/include/configs/a4m072.h b/include/configs/a4m072.h index 79099518e7..2ea43ffce1 100644 --- a/include/configs/a4m072.h +++ b/include/configs/a4m072.h @@ -81,7 +81,6 @@ /* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IDE #if defined(CONFIG_PCI) @@ -145,25 +144,6 @@ */ #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ - -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* 1010010x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 -#define CONFIG_SYS_EEPROM_WREN 1 -#define CONFIG_SYS_EEPROM_WP GPIO_PSC2_4 - /* * Flash configuration */ diff --git a/include/configs/ac14xx.h b/include/configs/ac14xx.h index ee015bb83d..2a46e9b864 100644 --- a/include/configs/ac14xx.h +++ b/include/configs/ac14xx.h @@ -336,28 +336,11 @@ #define CONFIG_CMDLINE_EDITING 1 /* command line history */ -/* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS - -/* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0x7F - /* * IIM - IC Identification Module */ #undef CONFIG_FSL_IIM -/* - * EEPROM configuration for Atmel AT24C01: - * 8-bit addresses, 30ms write delay, 32-Byte Page Write Mode - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 30 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 - /* * Ethernet configuration */ @@ -384,7 +367,6 @@ #define CONFIG_LOADS_ECHO 1 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 -#define CONFIG_CMD_EEPROM #undef CONFIG_CMD_FUSE #undef CONFIG_CMD_IDE #define CONFIG_CMD_JFFS2 diff --git a/include/configs/ap_sh4a_4a.h b/include/configs/ap_sh4a_4a.h index 5f5882dc8e..d3d72b634d 100644 --- a/include/configs/ap_sh4a_4a.h +++ b/include/configs/ap_sh4a_4a.h @@ -35,20 +35,6 @@ #define CONFIG_BITBANGMII #define CONFIG_BITBANGMII_MULTI -/* I2C */ -#define CONFIG_SH_SH7734_I2C 1 -#define CONFIG_HARD_I2C 1 -#define CONFIG_I2C_MULTI_BUS 1 -#define CONFIG_SYS_MAX_I2C_BUS 2 -#define CONFIG_SYS_I2C_MODULE 0 -#define CONFIG_SYS_I2C_SPEED 400000 /* 400 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x50 -#define CONFIG_SH_I2C_DATA_HIGH 4 -#define CONFIG_SH_I2C_DATA_LOW 5 -#define CONFIG_SH_I2C_CLOCK 500000000 -#define CONFIG_SH_I2C_BASE0 0xFFC70000 -#define CONFIG_SH_I2C_BASE1 0xFFC71000 - /* undef to save memory */ #define CONFIG_SYS_LONGHELP /* Monitor Command Prompt */ diff --git a/include/configs/apx4devkit.h b/include/configs/apx4devkit.h index a4c7847dab..cce39f27c7 100644 --- a/include/configs/apx4devkit.h +++ b/include/configs/apx4devkit.h @@ -79,12 +79,6 @@ #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 #endif -/* RTC */ -#ifdef CONFIG_CMD_DATE -#define CONFIG_RTC_PCF8563 -#define CONFIG_SYS_I2C_RTC_ADDR 0x51 -#endif - /* Boot Linux */ #define CONFIG_BOOTFILE "uImage" #define CONFIG_BOOTCOMMAND "run bootcmd_nand" diff --git a/include/configs/aria.h b/include/configs/aria.h index 94f6605d46..4d946fc44a 100644 --- a/include/configs/aria.h +++ b/include/configs/aria.h @@ -340,31 +340,11 @@ #endif -/* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS - -/* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#if 0 -#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */ -#endif - /* * IIM - IC Identification Module */ #undef CONFIG_FSL_IIM -/* - * EEPROM configuration for Atmel AT24C32A-10TQ-2.7: - * 16-bit addresses, 10ms write delay, 32-Byte Page Write Mode - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 - /* * Ethernet configuration */ @@ -392,7 +372,6 @@ #define CONFIG_LOADS_ECHO 1 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 -#define CONFIG_CMD_EEPROM #undef CONFIG_CMD_FUSE #undef CONFIG_CMD_IDE #define CONFIG_CMD_JFFS2 diff --git a/include/configs/axs10x.h b/include/configs/axs10x.h index 768e8fbfa4..66e8cd5e9a 100644 --- a/include/configs/axs10x.h +++ b/include/configs/axs10x.h @@ -100,7 +100,7 @@ /* * Environment settings */ -#define CONFIG_ENV_IS_IN_EEPROM +#define CONFIG_ENV_IS_NOWHERE #define CONFIG_ENV_SIZE SZ_512 #define CONFIG_ENV_OFFSET 0 diff --git a/include/configs/cm5200.h b/include/configs/cm5200.h index 0073cb5373..3a7d826837 100644 --- a/include/configs/cm5200.h +++ b/include/configs/cm5200.h @@ -44,7 +44,7 @@ /* * POST support */ -#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | CONFIG_SYS_POST_CPU | CONFIG_SYS_POST_I2C) +#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | CONFIG_SYS_POST_CPU) #define MPC5XXX_SRAM_POST_SIZE (MPC5XXX_SRAM_SIZE - 4) /* List of I2C addresses to be verified by POST */ #define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_SLAVE, \ @@ -199,16 +199,6 @@ "2m(kernel),27904k(rootfs)," \ "-(config)" -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 */ -#define CONFIG_SYS_I2C_SPEED 40000 /* 40 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x0 -#define CONFIG_SYS_I2C_IO 0x38 /* PCA9554AD I2C I/O port address */ -#define CONFIG_SYS_I2C_EEPROM 0x53 /* I2C EEPROM device address */ - /* * RTC configuration */ diff --git a/include/configs/digsy_mtc.h b/include/configs/digsy_mtc.h index 2b56945dd9..ab546c50cd 100644 --- a/include/configs/digsy_mtc.h +++ b/include/configs/digsy_mtc.h @@ -85,7 +85,6 @@ /* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IDE #define CONFIG_CMD_IRQ #define CONFIG_CMD_PCI @@ -205,36 +204,6 @@ #define CONFIG_BOOTCOMMAND "run mtcb_start" -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_MODULE 1 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70 - -/* - * RTC configuration - */ -#if defined(CONFIG_DIGSY_REV5) -#define CONFIG_SYS_I2C_RTC_ADDR 0x56 -#define CONFIG_RTC_RV3029 -/* Enable 5k Ohm trickle charge resistor */ -#define CONFIG_SYS_RV3029_TCR 0x20 -#else -#define CONFIG_RTC_DS1337 -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 -#define CONFIG_SYS_DS1339_TCR_VAL 0xAB /* diode + 4k resistor */ -#endif - /* * Flash configuration */ diff --git a/include/configs/ids8313.h b/include/configs/ids8313.h index 6b6bbbd5c0..7ffc9d1dd9 100644 --- a/include/configs/ids8313.h +++ b/include/configs/ids8313.h @@ -165,7 +165,6 @@ #define CONFIG_TSEC2 #define CONFIG_TSEC_ENET #define CONFIG_HARD_SPI -#define CONFIG_HARD_I2C /* * NOR FLASH setup diff --git a/include/configs/ipek01.h b/include/configs/ipek01.h index aff4adf5d0..ece72c6aa1 100644 --- a/include/configs/ipek01.h +++ b/include/configs/ipek01.h @@ -150,29 +150,6 @@ #define OF_SOC "soc5200@f0000000" #define OF_TBCLK (bd->bi_busfreq / 4) -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ - -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 - -/* - * RTC configuration - */ -#define CONFIG_RTC_PCF8563 -#define CONFIG_SYS_I2C_RTC_ADDR 0x51 - #define CONFIG_SYS_FLASH_BASE 0xFC000000 #define CONFIG_SYS_FLASH_SIZE 0x01000000 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + \ diff --git a/include/configs/jupiter.h b/include/configs/jupiter.h index 0d97317c7f..4461623118 100644 --- a/include/configs/jupiter.h +++ b/include/configs/jupiter.h @@ -127,25 +127,6 @@ #define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000" #endif -#if 0 -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ - -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70 -#endif - /* * Flash configuration */ diff --git a/include/configs/m28evk.h b/include/configs/m28evk.h index f6fa599e6b..c4717238bb 100644 --- a/include/configs/m28evk.h +++ b/include/configs/m28evk.h @@ -16,7 +16,6 @@ /* U-Boot Commands */ #define CONFIG_FAT_WRITE -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_NAND #define CONFIG_CMD_NAND_TRIMFFS @@ -63,11 +62,6 @@ #define CONFIG_FEC_MXC #endif -/* EEPROM */ -#ifdef CONFIG_CMD_EEPROM -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#endif - /* RTC */ #ifdef CONFIG_CMD_DATE /* Use the internal RTC in the MXS chip */ diff --git a/include/configs/manroland/mpc5200-common.h b/include/configs/manroland/mpc5200-common.h new file mode 100644 index 0000000000..68874dc029 --- /dev/null +++ b/include/configs/manroland/mpc5200-common.h @@ -0,0 +1,176 @@ +/* + * (C) Copyright 2009 + * Heiko Schocher, DENX Software Engineering, hs@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __MANROLAND_MPC52XX__COMMON_H +#define __MANROLAND_MPC52XX__COMMON_H + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_MPC5200 1 /* MPC5200 CPU */ + +/* ... running at 33.000000MHz */ +#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 + +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + +/* + * Serial console configuration + */ +#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200,\ + 230400 } + +#if (CONFIG_SYS_TEXT_BASE == 0xFFF00000) /* Boot low */ +# define CONFIG_SYS_LOWBOOT 1 +#endif + +/* + * IPB Bus clocking configuration. + */ +#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ + +/* + * Flash configuration + */ +#define CONFIG_SYS_FLASH_BASE 0xFF800000 + +#define CONFIG_SYS_FLASH_SIZE 0x00800000 /* 8 MByte */ + +#define CONFIG_ENV_ADDR (CONFIG_SYS_TEXT_BASE+0x40000) /* second sector */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks + (= chip selects) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout [ms]*/ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout [ms]*/ + +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_CFI_AMD_RESET + +/* + * Environment settings + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_SIZE 0x4000 +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) + +/* + * Memory map + */ +#define CONFIG_SYS_MBAR 0xF0000000 +#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE -\ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SRAM_BASE 0x80100000 /* CS 1 */ +#define CONFIG_SYS_DISPLAY_BASE 0x80600000 /* CS 3 */ + +/* Settings for XLB = 132 MHz */ +#define SDRAM_DDR 1 +#define SDRAM_MODE 0x018D0000 +#define SDRAM_EMODE 0x40090000 +#define SDRAM_CONTROL 0x714f0f00 +#define SDRAM_CONFIG1 0x73722930 +#define SDRAM_CONFIG2 0x47770000 +#define SDRAM_TAPDELAY 0x10000000 + +/* Use ON-Chip SRAM until RAM will be available */ +#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM +#ifdef CONFIG_POST +/* preserve space for the post_word at end of on-chip SRAM */ +#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE +#else +#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE +#endif + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +# define CONFIG_SYS_RAMBOOT 1 +#endif + +#define CONFIG_SYS_MONITOR_LEN (192 << 10) +#define CONFIG_SYS_MALLOC_LEN (512 << 10) +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) + +/* + * Ethernet configuration + */ +#define CONFIG_MPC5xxx_FEC 1 +#define CONFIG_MPC5xxx_FEC_MII100 +#define CONFIG_PHY_ADDR 0x00 +#define CONFIG_MII 1 + +/*use Hardware WDT */ +#define CONFIG_HW_WATCHDOG + +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ +#if defined(CONFIG_CMD_KGDB) +# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * Various low-level settings + */ +#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI +#define CONFIG_SYS_HID0_FINAL HID0_ICE + +#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE +#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE + +/* 8Mbit SRAM @0x80100000 */ +#define CONFIG_SYS_CS1_START CONFIG_SYS_SRAM_BASE + +#define CONFIG_SYS_CS_BURST 0x00000000 +#define CONFIG_SYS_CS_DEADCYCLE 0x33333333 + +/*----------------------------------------------------------------------- + * IDE/ATA stuff Supports IDE harddisk + *----------------------------------------------------------------------- + */ + +#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ + +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ + +#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ + +#define CONFIG_IDE_PREINIT 1 + +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 + +#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA + +/* Offset for data I/O */ +#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) + +/* Offset for normal register accesses */ +#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) + +/* Offset for alternate registers */ +#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) + +/* Interval between registers */ +#define CONFIG_SYS_ATA_STRIDE 4 + +#define CONFIG_ATAPI 1 + +#define OF_CPU "PowerPC,5200@0" +#define OF_SOC "soc5200@f0000000" +#define OF_TBCLK (bd->bi_busfreq / 4) +#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000" +#define CONFIG_OF_IDE_FIXUP + +#endif /* __MANROLAND_MPC52XX__COMMON_H */ diff --git a/include/configs/mecp5123.h b/include/configs/mecp5123.h index 1a9cb675df..fe94e663c5 100644 --- a/include/configs/mecp5123.h +++ b/include/configs/mecp5123.h @@ -241,26 +241,11 @@ #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -/* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed */ -#define CONFIG_SYS_I2C_SLAVE 0x7F /* slave address */ - /* * IIM - IC Identification Module */ #undef CONFIG_FSL_IIM -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM address */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Atmel: AT24C32A-10TQ-2.7 */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 32-Byte Page Write Mode */ -#define CONFIG_SYS_EEPROM_WREN /* Use EEPROM write protect */ - /* * Ethernet configuration */ @@ -280,7 +265,7 @@ /* * Environment */ -#define CONFIG_ENV_IS_IN_EEPROM /* Store env in I2C EEPROM */ +#define CONFIG_ENV_IS_NOWHERE /* Store env in I2C EEPROM */ #define CONFIG_ENV_SIZE 0x1000 #define CONFIG_ENV_OFFSET 0x0000 /* environment starts here */ @@ -288,7 +273,6 @@ #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ #define CONFIG_CMD_REGINFO -#define CONFIG_CMD_EEPROM #undef CONFIG_CMD_FUSE #undef CONFIG_CMD_IDE #define CONFIG_CMD_JFFS2 diff --git a/include/configs/motionpro.h b/include/configs/motionpro.h index 136db0dd26..cb5c346807 100644 --- a/include/configs/motionpro.h +++ b/include/configs/motionpro.h @@ -34,7 +34,6 @@ * Command line configuration. */ #define CONFIG_CMD_DTT -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IDE #define CONFIG_CMD_IMMAP #define CONFIG_CMD_JFFS2 @@ -255,21 +254,6 @@ #define CONFIG_SYS_ATA_REG_OFFSET CONFIG_SYS_ATA_DATA_OFFSET #define CONFIG_SYS_ATA_STRIDE 4 -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* select I2C module #2 */ -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 1 /* 2 bytes per write cycle */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 /* 2ms/cycle + 3ms extra */ - /* * RTC configuration */ @@ -283,12 +267,6 @@ #define ENABLE_GPIO_OUT 0x00000024 #define LED_ON 0x00000010 -/* - * Temperature sensor - */ -#define CONFIG_DTT_LM75 1 -#define CONFIG_DTT_SENSORS { 0x49 } - /* * Environment settings */ diff --git a/include/configs/mpc5121ads.h b/include/configs/mpc5121ads.h index dafb724e3f..f3961a6f35 100644 --- a/include/configs/mpc5121ads.h +++ b/include/configs/mpc5121ads.h @@ -327,28 +327,11 @@ #endif -/* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#if 0 -#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */ -#endif - /* * IIM - IC Identification Module */ #undef CONFIG_FSL_IIM -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM address */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Atmel: AT24C32A-10TQ-2.7 */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 32-Byte Page Write Mode */ - /* * Ethernet configuration */ @@ -396,7 +379,6 @@ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IDE #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_REGINFO diff --git a/include/configs/mxs.h b/include/configs/mxs.h index fdf596f82f..c403dda483 100644 --- a/include/configs/mxs.h +++ b/include/configs/mxs.h @@ -126,16 +126,6 @@ #endif #endif -/* I2C */ -#ifdef CONFIG_CMD_I2C -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_MXS -#define CONFIG_HARD_I2C -#ifndef CONFIG_SYS_I2C_SPEED -#define CONFIG_SYS_I2C_SPEED 400000 -#endif -#endif - /* LCD */ #ifdef CONFIG_VIDEO #define CONFIG_VIDEO_MXS diff --git a/include/configs/o2dnt-common.h b/include/configs/o2dnt-common.h index e2881a7177..1b4200bcbf 100644 --- a/include/configs/o2dnt-common.h +++ b/include/configs/o2dnt-common.h @@ -68,7 +68,6 @@ /* * Supported commands */ -#define CONFIG_CMD_EEPROM #ifdef CONFIG_PCI #define CONFIG_CMD_PCI #endif @@ -172,27 +171,6 @@ #define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */ #endif -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 or #2 */ -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration: - * - * O2DNT board is equiped with Ramtron FRAM device FM24CL16 - * 16 Kib Ferroelectric Nonvolatile serial RAM memory - * organized as 2048 x 8 bits and addressable as eight I2C devices - * 0x50 ... 0x57 each 256 bytes in size - * - */ -#define CONFIG_SYS_I2C_FRAM -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 /* * There is no write delay with FRAM, write operations are performed at bus * speed. Thus, no status polling or write delay is needed. diff --git a/include/configs/pcm030.h b/include/configs/pcm030.h index 6d8a2338a2..406f3e547a 100644 --- a/include/configs/pcm030.h +++ b/include/configs/pcm030.h @@ -49,7 +49,6 @@ Serial console configuration /* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_PCI @@ -120,31 +119,6 @@ IPB Bus clocking configuration. #define CONFIG_PCI_IO_SIZE 0x01000000 #define CONFIG_SYS_XLB_PIPELINING 1 -/*--------------------------------------------------------------------------- - I2C configuration ----------------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/*--------------------------------------------------------------------------- - EEPROM CAT24WC32 configuration ----------------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* 1010100x */ -#define CONFIG_SYS_I2C_FACT_ADDR 0x52 /* EEPROM CAT24WC32 */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ -#define CONFIG_SYS_EEPROM_SIZE 2048 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 15 - -/*--------------------------------------------------------------------------- -RTC configuration ----------------------------------------------------------------------------*/ -#define RTC -#define CONFIG_RTC_PCF8563 1 -#define CONFIG_SYS_I2C_RTC_ADDR 0x51 - /*--------------------------------------------------------------------------- Flash configuration ---------------------------------------------------------------------------*/ @@ -172,11 +146,10 @@ RTC configuration Environment settings ---------------------------------------------------------------------------*/ -/* pcm030 ships with environment is EEPROM by default */ -#define CONFIG_ENV_IS_IN_EEPROM 1 +#define CONFIG_ENV_IS_NOWHERE #define CONFIG_ENV_OFFSET 0x00 /* environment starts at the */ /*beginning of the EEPROM */ -#define CONFIG_ENV_SIZE CONFIG_SYS_EEPROM_SIZE +#define CONFIG_ENV_SIZE 2048 #define CONFIG_ENV_OVERWRITE 1 diff --git a/include/configs/pdm360ng.h b/include/configs/pdm360ng.h index 501611dde7..4bd8236b33 100644 --- a/include/configs/pdm360ng.h +++ b/include/configs/pdm360ng.h @@ -301,34 +301,11 @@ #define CONFIG_SYS_PDM360NG_COPROC_READ_DELAY 5000 #define CONFIG_SYS_PDM360NG_COPROC_BAUDRATE 38400 -/* - * I2C - */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_CMD_TREE -/* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0x7F - /* * IIM - IC Identification Module */ #undef CONFIG_FSL_IIM -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16-bit EEPROM addr */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* ST AT24C01 */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* 10ms of delay */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16-Byte Write Mode */ - -/* - * MAC addr in EEPROM - */ -#define CONFIG_SYS_I2C_EEPROM_BUS_NUM 0 -#define CONFIG_SYS_I2C_EEPROM_MAC_OFFSET 0x10 /* * Enabled only to delete "ethaddr" before testing * "ethaddr" setting from EEPROM @@ -344,12 +321,6 @@ #define CONFIG_FEC_AN_TIMEOUT 1 #define CONFIG_HAS_ETH0 -/* - * Configure on-board RTC - */ -#define CONFIG_RTC_M41T62 /* use M41T00 rtc via i2c */ -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ - /* * Environment */ @@ -367,7 +338,6 @@ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_REGINFO #undef CONFIG_CMD_FUSE diff --git a/include/configs/r0p7734.h b/include/configs/r0p7734.h index 642572fc95..b159b1ed8d 100644 --- a/include/configs/r0p7734.h +++ b/include/configs/r0p7734.h @@ -40,20 +40,6 @@ # define CONFIG_SMC911X_BASE (0x84000000) #endif -/* I2C */ -#define CONFIG_SH_SH7734_I2C 1 -#define CONFIG_HARD_I2C 1 -#define CONFIG_I2C_MULTI_BUS 1 -#define CONFIG_SYS_MAX_I2C_BUS 2 -#define CONFIG_SYS_I2C_MODULE 0 -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x50 -#define CONFIG_SH_I2C_DATA_HIGH 4 -#define CONFIG_SH_I2C_DATA_LOW 5 -#define CONFIG_SH_I2C_CLOCK 500000000 -#define CONFIG_SH_I2C_BASE0 0xFFC70000 -#define CONFIG_SH_I2C_BASE1 0xFFC7100 - /* undef to save memory */ #define CONFIG_SYS_LONGHELP /* Monitor Command Prompt */ diff --git a/include/configs/s32v234evb.h b/include/configs/s32v234evb.h index 398b3aa343..33487cd86f 100644 --- a/include/configs/s32v234evb.h +++ b/include/configs/s32v234evb.h @@ -97,16 +97,6 @@ #define CONFIG_PHY_MICREL #endif -#if 0 /* Disable until the I2C driver will be updated */ - -/* I2C Configs */ -#define CONFIG_CMD_I2C -#define CONFIG_HARD_I2C -#define CONFIG_I2C_MXC -#define CONFIG_SYS_I2C_BASE I2C0_BASE_ADDR -#define CONFIG_SYS_I2C_SPEED 100000 -#endif - #if 0 /* Disable until the FLASH will be implemented */ #define CONFIG_SYS_USE_NAND #endif diff --git a/include/configs/v38b.h b/include/configs/v38b.h index cc0007827d..0bc0ae517a 100644 --- a/include/configs/v38b.h +++ b/include/configs/v38b.h @@ -134,27 +134,6 @@ */ #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70 - -/* - * RTC configuration - */ -#define CONFIG_SYS_I2C_RTC_ADDR 0x51 - /* * Flash configuration - use CFI driver */ From 7ffce4f17fdbb110f572dae60670ec28db731ef2 Mon Sep 17 00:00:00 2001 From: Simon Glass Date: Fri, 12 May 2017 21:09:50 -0600 Subject: [PATCH 02/12] i2c: powerpc: Remove use of CONFIG_HARD_I2C Drop use of this long-deprecated option for powerpc. Signed-off-by: Simon Glass --- arch/powerpc/cpu/mpc512x/Makefile | 1 - arch/powerpc/cpu/mpc512x/i2c.c | 386 --------------- arch/powerpc/cpu/mpc5xxx/Makefile | 1 - arch/powerpc/cpu/mpc5xxx/i2c.c | 456 ----------------- arch/powerpc/cpu/mpc8260/Makefile | 2 +- arch/powerpc/cpu/mpc8260/commproc.c | 4 - arch/powerpc/cpu/mpc8260/i2c.c | 741 ---------------------------- arch/powerpc/cpu/mpc8xx/Makefile | 1 - arch/powerpc/cpu/mpc8xx/i2c.c | 672 ------------------------- board/freescale/m52277evb/README | 1 - board/freescale/m53017evb/README | 1 - board/freescale/m5373evb/README | 1 - board/freescale/m54455evb/README | 1 - board/freescale/m547xevb/README | 1 - 14 files changed, 1 insertion(+), 2268 deletions(-) delete mode 100644 arch/powerpc/cpu/mpc512x/i2c.c delete mode 100644 arch/powerpc/cpu/mpc5xxx/i2c.c delete mode 100644 arch/powerpc/cpu/mpc8260/i2c.c delete mode 100644 arch/powerpc/cpu/mpc8xx/i2c.c diff --git a/arch/powerpc/cpu/mpc512x/Makefile b/arch/powerpc/cpu/mpc512x/Makefile index 98991c688b..933deebdae 100644 --- a/arch/powerpc/cpu/mpc512x/Makefile +++ b/arch/powerpc/cpu/mpc512x/Makefile @@ -9,7 +9,6 @@ obj-y := cpu.o obj-y += traps.o obj-y += cpu_init.o obj-y += fixed_sdram.o -obj-y += i2c.o obj-y += interrupts.o obj-y += iopin.o obj-y += serial.o diff --git a/arch/powerpc/cpu/mpc512x/i2c.c b/arch/powerpc/cpu/mpc512x/i2c.c deleted file mode 100644 index 15d519a116..0000000000 --- a/arch/powerpc/cpu/mpc512x/i2c.c +++ /dev/null @@ -1,386 +0,0 @@ -/* - * (C) Copyright 2003 - 2009 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - * - * Based on the MPC5xxx code. - */ - -#include -#include - -DECLARE_GLOBAL_DATA_PTR; - -#ifdef CONFIG_HARD_I2C - -#include - -/* by default set I2C bus 0 active */ -static unsigned int bus_num __attribute__ ((section (".data"))) = 0; - -#define I2C_TIMEOUT 100 -#define I2C_RETRIES 3 - -struct mpc512x_i2c_tap { - int scl2tap; - int tap2tap; -}; - -static int mpc_reg_in(volatile u32 *reg); -static void mpc_reg_out(volatile u32 *reg, int val, int mask); -static int wait_for_bb(void); -static int wait_for_pin(int *status); -static int do_address(uchar chip, char rdwr_flag); -static int send_bytes(uchar chip, char *buf, int len); -static int receive_bytes(uchar chip, char *buf, int len); -static int mpc_get_fdr(int); - -static int mpc_reg_in (volatile u32 *reg) -{ - int ret = in_be32(reg) >> 24; - - return ret; -} - -static void mpc_reg_out (volatile u32 *reg, int val, int mask) -{ - if (!mask) { - out_be32(reg, val << 24); - } else { - clrsetbits_be32(reg, mask << 24, (val & mask) << 24); - } -} - -static int wait_for_bb (void) -{ - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; - volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num]; - int timeout = I2C_TIMEOUT; - int status; - - status = mpc_reg_in (®s->msr); - - while (timeout-- && (status & I2C_BB)) { - mpc_reg_out (®s->mcr, I2C_STA, I2C_STA); - (void)mpc_reg_in(®s->mdr); - mpc_reg_out (®s->mcr, 0, I2C_STA); - mpc_reg_out (®s->mcr, 0, 0); - mpc_reg_out (®s->mcr, I2C_EN, 0); - - udelay (1000); - status = mpc_reg_in (®s->msr); - } - - return (status & I2C_BB); -} - -static int wait_for_pin (int *status) -{ - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; - volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num]; - int timeout = I2C_TIMEOUT; - - *status = mpc_reg_in (®s->msr); - - while (timeout-- && !(*status & I2C_IF)) { - udelay (1000); - *status = mpc_reg_in (®s->msr); - } - - if (!(*status & I2C_IF)) { - return -1; - } - - mpc_reg_out (®s->msr, 0, I2C_IF); - - return 0; -} - -static int do_address (uchar chip, char rdwr_flag) -{ - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; - volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num]; - int status; - - chip <<= 1; - - if (rdwr_flag) { - chip |= 1; - } - - mpc_reg_out (®s->mcr, I2C_TX, I2C_TX); - mpc_reg_out (®s->mdr, chip, 0); - - if (wait_for_pin (&status)) { - return -2; - } - - if (status & I2C_RXAK) { - return -3; - } - - return 0; -} - -static int send_bytes (uchar chip, char *buf, int len) -{ - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; - volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num]; - int wrcount; - int status; - - for (wrcount = 0; wrcount < len; ++wrcount) { - - mpc_reg_out (®s->mdr, buf[wrcount], 0); - - if (wait_for_pin (&status)) { - break; - } - - if (status & I2C_RXAK) { - break; - } - - } - - return !(wrcount == len); -} - -static int receive_bytes (uchar chip, char *buf, int len) -{ - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; - volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num]; - int dummy = 1; - int rdcount = 0; - int status; - int i; - - mpc_reg_out (®s->mcr, 0, I2C_TX); - - for (i = 0; i < len; ++i) { - buf[rdcount] = mpc_reg_in (®s->mdr); - - if (dummy) { - dummy = 0; - } else { - rdcount++; - } - - if (wait_for_pin (&status)) { - return -4; - } - } - - mpc_reg_out (®s->mcr, I2C_TXAK, I2C_TXAK); - buf[rdcount++] = mpc_reg_in (®s->mdr); - - if (wait_for_pin (&status)) { - return -5; - } - - mpc_reg_out (®s->mcr, 0, I2C_TXAK); - - return 0; -} - -/**************** I2C API ****************/ - -void i2c_init (int speed, int saddr) -{ - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; - int i; - - for (i = 0; i < I2C_BUS_CNT; i++){ - volatile i2c512x_dev_t *regs = &im->i2c.dev[i]; - - mpc_reg_out (®s->mcr, 0, 0); - - /* Set clock */ - mpc_reg_out (®s->mfdr, mpc_get_fdr (speed), 0); - mpc_reg_out (®s->madr, saddr << 1, 0); - - /* Enable module */ - mpc_reg_out (®s->mcr, I2C_EN, I2C_INIT_MASK); - mpc_reg_out (®s->msr, 0, I2C_IF); - } - - /* Disable interrupts */ - out_be32(&im->i2c.icr, 0); - - /* Turn off filters */ - out_be32(&im->i2c.mifr, 0); -} - -static int mpc_get_fdr (int speed) -{ - static int fdr = -1; - - if (fdr == -1) { - ulong best_speed = 0; - ulong divider; - ulong ips, scl; - ulong bestmatch = 0xffffffffUL; - int best_i = 0, best_j = 0, i, j; - int SCL_Tap[] = { 9, 10, 12, 15, 5, 6, 7, 8}; - struct mpc512x_i2c_tap scltap[] = { - {4, 1}, - {4, 2}, - {6, 4}, - {6, 8}, - {14, 16}, - {30, 32}, - {62, 64}, - {126, 128} - }; - - ips = gd->arch.ips_clk; - for (i = 7; i >= 0; i--) { - for (j = 7; j >= 0; j--) { - scl = 2 * (scltap[j].scl2tap + - (SCL_Tap[i] - 1) * scltap[j].tap2tap - + 2); - if (ips <= speed*scl) { - if ((speed*scl - ips) < bestmatch) { - bestmatch = speed*scl - ips; - best_i = i; - best_j = j; - best_speed = ips/scl; - } - } - } - } - divider = (best_i & 3) | ((best_i & 4) << 3) | (best_j << 2); - if (gd->flags & GD_FLG_RELOC) { - fdr = divider; - } else { - debug("%ld kHz, \n", best_speed / 1000); - return divider; - } - } - - return fdr; -} - -int i2c_probe (uchar chip) -{ - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; - volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num]; - int i; - - for (i = 0; i < I2C_RETRIES; i++) { - mpc_reg_out (®s->mcr, I2C_STA, I2C_STA); - - if (! do_address (chip, 0)) { - mpc_reg_out (®s->mcr, 0, I2C_STA); - udelay (500); - break; - } - - mpc_reg_out (®s->mcr, 0, I2C_STA); - udelay (500); - } - - return (i == I2C_RETRIES); -} - -int i2c_read (uchar chip, uint addr, int alen, uchar *buf, int len) -{ - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; - volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num]; - char xaddr[4]; - int ret = -1; - - xaddr[0] = (addr >> 24) & 0xFF; - xaddr[1] = (addr >> 16) & 0xFF; - xaddr[2] = (addr >> 8) & 0xFF; - xaddr[3] = addr & 0xFF; - - if (wait_for_bb ()) { - printf ("i2c_read: bus is busy\n"); - goto Done; - } - - mpc_reg_out (®s->mcr, I2C_STA, I2C_STA); - if (do_address (chip, 0)) { - printf ("i2c_read: failed to address chip\n"); - goto Done; - } - - if (send_bytes (chip, &xaddr[4-alen], alen)) { - printf ("i2c_read: send_bytes failed\n"); - goto Done; - } - - mpc_reg_out (®s->mcr, I2C_RSTA, I2C_RSTA); - if (do_address (chip, 1)) { - printf ("i2c_read: failed to address chip\n"); - goto Done; - } - - if (receive_bytes (chip, (char *)buf, len)) { - printf ("i2c_read: receive_bytes failed\n"); - goto Done; - } - - ret = 0; -Done: - mpc_reg_out (®s->mcr, 0, I2C_STA); - return ret; -} - -int i2c_write (uchar chip, uint addr, int alen, uchar *buf, int len) -{ - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; - volatile i2c512x_dev_t *regs = &im->i2c.dev[bus_num]; - char xaddr[4]; - int ret = -1; - - xaddr[0] = (addr >> 24) & 0xFF; - xaddr[1] = (addr >> 16) & 0xFF; - xaddr[2] = (addr >> 8) & 0xFF; - xaddr[3] = addr & 0xFF; - - if (wait_for_bb ()) { - printf ("i2c_write: bus is busy\n"); - goto Done; - } - - mpc_reg_out (®s->mcr, I2C_STA, I2C_STA); - if (do_address (chip, 0)) { - printf ("i2c_write: failed to address chip\n"); - goto Done; - } - - if (send_bytes (chip, &xaddr[4-alen], alen)) { - printf ("i2c_write: send_bytes failed\n"); - goto Done; - } - - if (send_bytes (chip, (char *)buf, len)) { - printf ("i2c_write: send_bytes failed\n"); - goto Done; - } - - ret = 0; -Done: - mpc_reg_out (®s->mcr, 0, I2C_STA); - return ret; -} - -int i2c_set_bus_num (unsigned int bus) -{ - if (bus >= I2C_BUS_CNT) { - return -1; - } - bus_num = bus; - - return 0; -} - -unsigned int i2c_get_bus_num (void) -{ - return bus_num; -} - -#endif /* CONFIG_HARD_I2C */ diff --git a/arch/powerpc/cpu/mpc5xxx/Makefile b/arch/powerpc/cpu/mpc5xxx/Makefile index 5c67e1d37d..88e3b2e3ae 100644 --- a/arch/powerpc/cpu/mpc5xxx/Makefile +++ b/arch/powerpc/cpu/mpc5xxx/Makefile @@ -9,7 +9,6 @@ extra-y = start.o extra-y += traps.o obj-y += io.o obj-y += firmware_sc_task_bestcomm.impl.o -obj-y += i2c.o obj-y += cpu.o obj-y += cpu_init.o obj-y += ide.o diff --git a/arch/powerpc/cpu/mpc5xxx/i2c.c b/arch/powerpc/cpu/mpc5xxx/i2c.c deleted file mode 100644 index 73601ae184..0000000000 --- a/arch/powerpc/cpu/mpc5xxx/i2c.c +++ /dev/null @@ -1,456 +0,0 @@ -/* - * (C) Copyright 2003 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include - -DECLARE_GLOBAL_DATA_PTR; - -#ifdef CONFIG_HARD_I2C - -#include -#include - -#if !defined(CONFIG_I2C_MULTI_BUS) -#if (CONFIG_SYS_I2C_MODULE == 2) -#define I2C_BASE MPC5XXX_I2C2 -#elif (CONFIG_SYS_I2C_MODULE == 1) -#define I2C_BASE MPC5XXX_I2C1 -#else -#error CONFIG_SYS_I2C_MODULE is not properly configured -#endif -#else -static unsigned int i2c_bus_num __attribute__ ((section (".data"))) = - CONFIG_SYS_SPD_BUS_NUM; -static unsigned int i2c_bus_speed[2] = {CONFIG_SYS_I2C_SPEED, - CONFIG_SYS_I2C_SPEED}; - -static const unsigned long i2c_dev[2] = { - MPC5XXX_I2C1, - MPC5XXX_I2C2, -}; - -#define I2C_BASE ((struct mpc5xxx_i2c *)i2c_dev[i2c_bus_num]) -#endif - -#define I2C_TIMEOUT 6667 -#define I2C_RETRIES 3 - -struct mpc5xxx_i2c_tap { - int scl2tap; - int tap2tap; -}; - -static int mpc_reg_in (volatile u32 *reg); -static void mpc_reg_out (volatile u32 *reg, int val, int mask); -static int wait_for_bb (void); -static int wait_for_pin (int *status); -static int do_address (uchar chip, char rdwr_flag); -static int send_bytes (uchar chip, char *buf, int len); -static int receive_bytes (uchar chip, char *buf, int len); -static int mpc_get_fdr (int); - -static int mpc_reg_in(volatile u32 *reg) -{ - int ret = *reg >> 24; - __asm__ __volatile__ ("eieio"); - return ret; -} - -static void mpc_reg_out(volatile u32 *reg, int val, int mask) -{ - int tmp; - - if (!mask) { - *reg = val << 24; - } else { - tmp = mpc_reg_in(reg); - *reg = ((tmp & ~mask) | (val & mask)) << 24; - } - __asm__ __volatile__ ("eieio"); - - return; -} - -static int wait_for_bb(void) -{ - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE; - int timeout = I2C_TIMEOUT; - int status; - - status = mpc_reg_in(®s->msr); - - while (timeout-- && (status & I2C_BB)) { - mpc_reg_out(®s->mcr, I2C_STA, I2C_STA); - (void)mpc_reg_in(®s->mdr); - mpc_reg_out(®s->mcr, 0, I2C_STA); - mpc_reg_out(®s->mcr, 0, 0); - mpc_reg_out(®s->mcr, I2C_EN, 0); - udelay(15); - status = mpc_reg_in(®s->msr); - } - - return (status & I2C_BB); -} - -static int wait_for_pin(int *status) -{ - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE; - int timeout = I2C_TIMEOUT; - - *status = mpc_reg_in(®s->msr); - - while (timeout-- && !(*status & I2C_IF)) { - udelay(15); - *status = mpc_reg_in(®s->msr); - } - - if (!(*status & I2C_IF)) { - return -1; - } - - mpc_reg_out(®s->msr, 0, I2C_IF); - - return 0; -} - -static int do_address(uchar chip, char rdwr_flag) -{ - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE; - int status; - - chip <<= 1; - - if (rdwr_flag) { - chip |= 1; - } - - mpc_reg_out(®s->mcr, I2C_TX, I2C_TX); - mpc_reg_out(®s->mdr, chip, 0); - - if (wait_for_pin(&status)) { - return -2; - } - - if (status & I2C_RXAK) { - return -3; - } - - return 0; -} - -static int send_bytes(uchar chip, char *buf, int len) -{ - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE; - int wrcount; - int status; - - for (wrcount = 0; wrcount < len; ++wrcount) { - - mpc_reg_out(®s->mdr, buf[wrcount], 0); - - if (wait_for_pin(&status)) { - break; - } - - if (status & I2C_RXAK) { - break; - } - - } - - return !(wrcount == len); -} - -static int receive_bytes(uchar chip, char *buf, int len) -{ - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE; - int dummy = 1; - int rdcount = 0; - int status; - int i; - - mpc_reg_out(®s->mcr, 0, I2C_TX); - - for (i = 0; i < len; ++i) { - buf[rdcount] = mpc_reg_in(®s->mdr); - - if (dummy) { - dummy = 0; - } else { - rdcount++; - } - - - if (wait_for_pin(&status)) { - return -4; - } - } - - mpc_reg_out(®s->mcr, I2C_TXAK, I2C_TXAK); - buf[rdcount++] = mpc_reg_in(®s->mdr); - - if (wait_for_pin(&status)) { - return -5; - } - - mpc_reg_out(®s->mcr, 0, I2C_TXAK); - - return 0; -} - -#if defined(CONFIG_SYS_I2C_INIT_MPC5XXX) - -#define FDR510(x) (u8) (((x & 0x20) >> 3) | (x & 0x3)) -#define FDR432(x) (u8) ((x & 0x1C) >> 2) -/* - * Reset any i2c devices that may have been interrupted during a system reset. - * Normally this would be accomplished by clocking the line until SCL and SDA - * are released and then sending a start condtiion (From an Atmel datasheet). - * There is no direct access to the i2c pins so instead create start commands - * through the i2c interface. Send a start command then delay for the SDA Hold - * time, repeat this by disabling/enabling the bus a total of 9 times. - */ -static void send_reset(void) -{ - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE; - int i; - u32 delay; - u8 fdr; - int SDA_Tap[] = { 3, 3, 4, 4, 1, 1, 2, 2}; - struct mpc5xxx_i2c_tap scltap[] = { - {4, 1}, - {4, 2}, - {6, 4}, - {6, 8}, - {14, 16}, - {30, 32}, - {62, 64}, - {126, 128} - }; - - fdr = (u8)mpc_reg_in(®s->mfdr); - - delay = scltap[FDR432(fdr)].scl2tap + ((SDA_Tap[FDR510(fdr)] - 1) * \ - scltap[FDR432(fdr)].tap2tap) + 3; - - for (i = 0; i < 9; i++) { - mpc_reg_out(®s->mcr, I2C_EN|I2C_STA|I2C_TX, I2C_INIT_MASK); - udelay(delay); - mpc_reg_out(®s->mcr, 0, I2C_INIT_MASK); - udelay(delay); - } - - mpc_reg_out(®s->mcr, I2C_EN, I2C_INIT_MASK); -} -#endif /* CONFIG_SYS_I2c_INIT_MPC5XXX */ - -/**************** I2C API ****************/ - -void i2c_init(int speed, int saddr) -{ - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE; - - mpc_reg_out(®s->mcr, 0, 0); - mpc_reg_out(®s->madr, saddr << 1, 0); - - /* Set clock - */ - mpc_reg_out(®s->mfdr, mpc_get_fdr(speed), 0); - - /* Enable module - */ - mpc_reg_out(®s->mcr, I2C_EN, I2C_INIT_MASK); - mpc_reg_out(®s->msr, 0, I2C_IF); - -#if defined(CONFIG_SYS_I2C_INIT_MPC5XXX) - send_reset(); -#endif - return; -} - -static int mpc_get_fdr(int speed) -{ - static int fdr = -1; - - if (fdr == -1) { - ulong best_speed = 0; - ulong divider; - ulong ipb, scl; - ulong bestmatch = 0xffffffffUL; - int best_i = 0, best_j = 0, i, j; - int SCL_Tap[] = { 9, 10, 12, 15, 5, 6, 7, 8}; - struct mpc5xxx_i2c_tap scltap[] = { - {4, 1}, - {4, 2}, - {6, 4}, - {6, 8}, - {14, 16}, - {30, 32}, - {62, 64}, - {126, 128} - }; - - ipb = gd->arch.ipb_clk; - for (i = 7; i >= 0; i--) { - for (j = 7; j >= 0; j--) { - scl = 2 * (scltap[j].scl2tap + - (SCL_Tap[i] - 1) * scltap[j].tap2tap + 2); - if (ipb <= speed*scl) { - if ((speed*scl - ipb) < bestmatch) { - bestmatch = speed*scl - ipb; - best_i = i; - best_j = j; - best_speed = ipb/scl; - } - } - } - } - divider = (best_i & 3) | ((best_i & 4) << 3) | (best_j << 2); - if (gd->flags & GD_FLG_RELOC) { - fdr = divider; - } else { - printf("%ld kHz, ", best_speed / 1000); - return divider; - } - } - - return fdr; -} - -int i2c_probe(uchar chip) -{ - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE; - int i; - - for (i = 0; i < I2C_RETRIES; i++) { - mpc_reg_out(®s->mcr, I2C_STA, I2C_STA); - - if (! do_address(chip, 0)) { - mpc_reg_out(®s->mcr, 0, I2C_STA); - udelay(500); - break; - } - - mpc_reg_out(®s->mcr, 0, I2C_STA); - udelay(500); - } - - return (i == I2C_RETRIES); -} - -int i2c_read(uchar chip, uint addr, int alen, uchar *buf, int len) -{ - char xaddr[4]; - struct mpc5xxx_i2c * regs = (struct mpc5xxx_i2c *)I2C_BASE; - int ret = -1; - - xaddr[0] = (addr >> 24) & 0xFF; - xaddr[1] = (addr >> 16) & 0xFF; - xaddr[2] = (addr >> 8) & 0xFF; - xaddr[3] = addr & 0xFF; - - if (wait_for_bb()) { - printf("i2c_read: bus is busy\n"); - goto Done; - } - - mpc_reg_out(®s->mcr, I2C_STA, I2C_STA); - if (do_address(chip, 0)) { - printf("i2c_read: failed to address chip\n"); - goto Done; - } - - if (send_bytes(chip, &xaddr[4-alen], alen)) { - printf("i2c_read: send_bytes failed\n"); - goto Done; - } - - mpc_reg_out(®s->mcr, I2C_RSTA, I2C_RSTA); - if (do_address(chip, 1)) { - printf("i2c_read: failed to address chip\n"); - goto Done; - } - - if (receive_bytes(chip, (char *)buf, len)) { - printf("i2c_read: receive_bytes failed\n"); - goto Done; - } - - ret = 0; -Done: - mpc_reg_out(®s->mcr, 0, I2C_STA); - return ret; -} - -int i2c_write(uchar chip, uint addr, int alen, uchar *buf, int len) -{ - char xaddr[4]; - struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE; - int ret = -1; - - xaddr[0] = (addr >> 24) & 0xFF; - xaddr[1] = (addr >> 16) & 0xFF; - xaddr[2] = (addr >> 8) & 0xFF; - xaddr[3] = addr & 0xFF; - - if (wait_for_bb()) { - printf("i2c_write: bus is busy\n"); - goto Done; - } - - mpc_reg_out(®s->mcr, I2C_STA, I2C_STA); - if (do_address(chip, 0)) { - printf("i2c_write: failed to address chip\n"); - goto Done; - } - - if (send_bytes(chip, &xaddr[4-alen], alen)) { - printf("i2c_write: send_bytes failed\n"); - goto Done; - } - - if (send_bytes(chip, (char *)buf, len)) { - printf("i2c_write: send_bytes failed\n"); - goto Done; - } - - ret = 0; -Done: - mpc_reg_out(®s->mcr, 0, I2C_STA); - return ret; -} - -#if defined(CONFIG_I2C_MULTI_BUS) -int i2c_set_bus_num(unsigned int bus) -{ - if (bus > 1) - return -1; - - i2c_bus_num = bus; - i2c_init(i2c_bus_speed[bus], CONFIG_SYS_I2C_SLAVE); - return 0; -} - -int i2c_set_bus_speed(unsigned int speed) -{ - i2c_init(speed, CONFIG_SYS_I2C_SLAVE); - return 0; -} - -unsigned int i2c_get_bus_num(void) -{ - return i2c_bus_num; -} - -unsigned int i2c_get_bus_speed(void) -{ - return i2c_bus_speed[i2c_bus_num]; -} -#endif - - -#endif /* CONFIG_HARD_I2C */ diff --git a/arch/powerpc/cpu/mpc8260/Makefile b/arch/powerpc/cpu/mpc8260/Makefile index 83adc4c436..72dd8aba25 100644 --- a/arch/powerpc/cpu/mpc8260/Makefile +++ b/arch/powerpc/cpu/mpc8260/Makefile @@ -7,7 +7,7 @@ extra-y = start.o obj-y = traps.o serial_smc.o serial_scc.o cpu.o cpu_init.o speed.o \ - interrupts.o ether_fcc.o i2c.o commproc.o \ + interrupts.o ether_fcc.o commproc.o \ bedbug_603e.o pci.o spi.o kgdb.o obj-$(CONFIG_ETHER_ON_SCC) += ether_scc.o diff --git a/arch/powerpc/cpu/mpc8260/commproc.c b/arch/powerpc/cpu/mpc8260/commproc.c index 484bd17745..ff69881089 100644 --- a/arch/powerpc/cpu/mpc8260/commproc.c +++ b/arch/powerpc/cpu/mpc8260/commproc.c @@ -41,10 +41,6 @@ m8260_cpm_reset(void) do { /* Spin until command processed */ __asm__ __volatile__ ("eieio"); } while ((immr->im_cpm.cp_cpcr & CPM_CR_FLG) && ++count < 1000000); - -#ifdef CONFIG_HARD_I2C - immr->im_dprambase16[PROFF_I2C_BASE / sizeof(u16)] = 0; -#endif } /* Allocate some memory from the dual ported ram. diff --git a/arch/powerpc/cpu/mpc8260/i2c.c b/arch/powerpc/cpu/mpc8260/i2c.c deleted file mode 100644 index a0de101329..0000000000 --- a/arch/powerpc/cpu/mpc8260/i2c.c +++ /dev/null @@ -1,741 +0,0 @@ -/* - * (C) Copyright 2000 - * Paolo Scaffardi, AIRVENT SAM s.p.a - RIMINI(ITALY), arsenio@tin.it - * - * (C) Copyright 2000 Sysgo Real-Time Solutions, GmbH - * Marius Groeger - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include - -#if defined(CONFIG_HARD_I2C) - -#include -#include - -DECLARE_GLOBAL_DATA_PTR; - -#if defined(CONFIG_I2C_MULTI_BUS) -static unsigned int i2c_bus_num __attribute__ ((section(".data"))) = 0; -#endif /* CONFIG_I2C_MULTI_BUS */ - -/* uSec to wait between polls of the i2c */ -#define DELAY_US 100 -/* uSec to wait for the CPM to start processing the buffer */ -#define START_DELAY_US 1000 - -/* - * tx/rx per-byte timeout: we delay DELAY_US uSec between polls so the - * timeout will be (tx_length + rx_length) * DELAY_US * TOUT_LOOP - */ -#define TOUT_LOOP 5 - -/* - * Set default values - */ -#ifndef CONFIG_SYS_I2C_SPEED -#define CONFIG_SYS_I2C_SPEED 50000 -#endif - - -typedef void (*i2c_ecb_t) (int, int, void *); /* error callback function */ - -/* This structure keeps track of the bd and buffer space usage. */ -typedef struct i2c_state { - int rx_idx; /* index to next free Rx BD */ - int tx_idx; /* index to next free Tx BD */ - void *rxbd; /* pointer to next free Rx BD */ - void *txbd; /* pointer to next free Tx BD */ - int tx_space; /* number of Tx bytes left */ - unsigned char *tx_buf; /* pointer to free Tx area */ - i2c_ecb_t err_cb; /* error callback function */ - void *cb_data; /* private data to be passed */ -} i2c_state_t; - -/* flags for i2c_send() and i2c_receive() */ -#define I2CF_ENABLE_SECONDARY 0x01 /* secondary_address is valid */ -#define I2CF_START_COND 0x02 /* tx: generate start condition */ -#define I2CF_STOP_COND 0x04 /* tx: generate stop condition */ - -/* return codes */ -#define I2CERR_NO_BUFFERS 1 /* no more BDs or buffer space */ -#define I2CERR_MSG_TOO_LONG 2 /* tried to send/receive to much data */ -#define I2CERR_TIMEOUT 3 /* timeout in i2c_doio() */ -#define I2CERR_QUEUE_EMPTY 4 /* i2c_doio called without send/rcv */ -#define I2CERR_IO_ERROR 5 /* had an error during comms */ - -/* error callback flags */ -#define I2CECB_RX_ERR 0x10 /* this is a receive error */ -#define I2CECB_RX_OV 0x02 /* receive overrun error */ -#define I2CECB_RX_MASK 0x0f /* mask for error bits */ -#define I2CECB_TX_ERR 0x20 /* this is a transmit error */ -#define I2CECB_TX_CL 0x01 /* transmit collision error */ -#define I2CECB_TX_UN 0x02 /* transmit underflow error */ -#define I2CECB_TX_NAK 0x04 /* transmit no ack error */ -#define I2CECB_TX_MASK 0x0f /* mask for error bits */ -#define I2CECB_TIMEOUT 0x40 /* this is a timeout error */ - -#define ERROR_I2C_NONE 0 -#define ERROR_I2C_LENGTH 1 - -#define I2C_WRITE_BIT 0x00 -#define I2C_READ_BIT 0x01 - -#define I2C_RXTX_LEN 128 /* maximum tx/rx buffer length */ - - -#define NUM_RX_BDS 4 -#define NUM_TX_BDS 4 -#define MAX_TX_SPACE 256 - -typedef struct I2C_BD { - unsigned short status; - unsigned short length; - unsigned char *addr; -} I2C_BD; - -#define BD_I2C_TX_START 0x0400 /* special status for i2c: Start condition */ - -#define BD_I2C_TX_CL 0x0001 /* collision error */ -#define BD_I2C_TX_UN 0x0002 /* underflow error */ -#define BD_I2C_TX_NAK 0x0004 /* no acknowledge error */ -#define BD_I2C_TX_ERR (BD_I2C_TX_NAK|BD_I2C_TX_UN|BD_I2C_TX_CL) - -#define BD_I2C_RX_ERR BD_SC_OV - -/* - * Returns the best value of I2BRG to meet desired clock speed of I2C with - * input parameters (clock speed, filter, and predivider value). - * It returns computer speed value and the difference between it and desired - * speed. - */ -static inline int -i2c_roundrate(int hz, int speed, int filter, int modval, - int *brgval, int *totspeed) -{ - int moddiv = 1 << (5 - (modval & 3)), brgdiv, div; - - debug("\t[I2C] trying hz=%d, speed=%d, filter=%d, modval=%d\n", - hz, speed, filter, modval); - - div = moddiv * speed; - brgdiv = (hz + div - 1) / div; - - debug("\t\tmoddiv=%d, brgdiv=%d\n", moddiv, brgdiv); - - *brgval = ((brgdiv + 1) / 2) - 3 - (2 * filter); - - if ((*brgval < 0) || (*brgval > 255)) { - debug("\t\trejected brgval=%d\n", *brgval); - return -1; - } - - brgdiv = 2 * (*brgval + 3 + (2 * filter)); - div = moddiv * brgdiv; - *totspeed = hz / div; - - debug("\t\taccepted brgval=%d, totspeed=%d\n", *brgval, *totspeed); - - return 0; -} - -/* - * Sets the I2C clock predivider and divider to meet required clock speed. - */ -static int i2c_setrate(int hz, int speed) -{ - immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; - volatile i2c8260_t *i2c = (i2c8260_t *)&immap->im_i2c; - int brgval, - modval, /* 0-3 */ - bestspeed_diff = speed, - bestspeed_brgval = 0, - bestspeed_modval = 0, - bestspeed_filter = 0, - totspeed, - filter = 0; /* Use this fixed value */ - - for (modval = 0; modval < 4; modval++) { - if (i2c_roundrate(hz, speed, filter, modval, &brgval, &totspeed) - == 0) { - int diff = speed - totspeed; - - if ((diff >= 0) && (diff < bestspeed_diff)) { - bestspeed_diff = diff; - bestspeed_modval = modval; - bestspeed_brgval = brgval; - bestspeed_filter = filter; - } - } - } - - debug("[I2C] Best is:\n"); - debug("[I2C] CPU=%dhz RATE=%d F=%d I2MOD=%08x I2BRG=%08x DIFF=%dhz\n", - hz, speed, bestspeed_filter, bestspeed_modval, bestspeed_brgval, - bestspeed_diff); - - i2c->i2c_i2mod |= ((bestspeed_modval & 3) << 1) | - (bestspeed_filter << 3); - i2c->i2c_i2brg = bestspeed_brgval & 0xff; - - debug("[I2C] i2mod=%08x i2brg=%08x\n", i2c->i2c_i2mod, - i2c->i2c_i2brg); - - return 1; -} - -void i2c_init(int speed, int slaveadd) -{ - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; - volatile cpm8260_t *cp = (cpm8260_t *)&immap->im_cpm; - volatile i2c8260_t *i2c = (i2c8260_t *)&immap->im_i2c; - volatile iic_t *iip; - ulong rbase, tbase; - volatile I2C_BD *rxbd, *txbd; - uint dpaddr; - -#ifdef CONFIG_SYS_I2C_INIT_BOARD - /* - * call board specific i2c bus reset routine before accessing the - * environment, which might be in a chip on that bus. For details - * about this problem see doc/I2C_Edge_Conditions. - */ - i2c_init_board(); -#endif - - dpaddr = immap->im_dprambase16[PROFF_I2C_BASE / sizeof(u16)]; - if (dpaddr == 0) { - /* need to allocate dual port ram */ - dpaddr = m8260_cpm_dpalloc(64 + - (NUM_RX_BDS * sizeof(I2C_BD)) + - (NUM_TX_BDS * sizeof(I2C_BD)) + - MAX_TX_SPACE, 64); - immap->im_dprambase16[PROFF_I2C_BASE / sizeof(u16)] = - dpaddr; - } - - /* - * initialise data in dual port ram: - * - * dpaddr -> parameter ram (64 bytes) - * rbase -> rx BD (NUM_RX_BDS * sizeof(I2C_BD) bytes) - * tbase -> tx BD (NUM_TX_BDS * sizeof(I2C_BD) bytes) - * tx buffer (MAX_TX_SPACE bytes) - */ - - iip = (iic_t *)&immap->im_dprambase[dpaddr]; - memset((void *)iip, 0, sizeof(iic_t)); - - rbase = dpaddr + 64; - tbase = rbase + NUM_RX_BDS * sizeof(I2C_BD); - - /* Disable interrupts */ - i2c->i2c_i2mod = 0x00; - i2c->i2c_i2cmr = 0x00; - i2c->i2c_i2cer = 0xff; - i2c->i2c_i2add = slaveadd; - - /* - * Set the I2C BRG Clock division factor from desired i2c rate - * and current CPU rate (we assume sccr dfbgr field is 0; - * divide BRGCLK by 1) - */ - debug("[I2C] Setting rate...\n"); - i2c_setrate(gd->arch.brg_clk, CONFIG_SYS_I2C_SPEED); - - /* Set I2C controller in master mode */ - i2c->i2c_i2com = 0x01; - - /* Initialize Tx/Rx parameters */ - iip->iic_rbase = rbase; - iip->iic_tbase = tbase; - rxbd = (I2C_BD *)((unsigned char *) &immap-> - im_dprambase[iip->iic_rbase]); - txbd = (I2C_BD *)((unsigned char *) &immap-> - im_dprambase[iip->iic_tbase]); - - debug("[I2C] rbase = %04x\n", iip->iic_rbase); - debug("[I2C] tbase = %04x\n", iip->iic_tbase); - debug("[I2C] rxbd = %08x\n", (int) rxbd); - debug("[I2C] txbd = %08x\n", (int) txbd); - - /* Set big endian byte order */ - iip->iic_tfcr = 0x10; - iip->iic_rfcr = 0x10; - - /* Set maximum receive size. */ - iip->iic_mrblr = I2C_RXTX_LEN; - - cp->cp_cpcr = mk_cr_cmd(CPM_CR_I2C_PAGE, - CPM_CR_I2C_SBLOCK, - 0x00, CPM_CR_INIT_TRX) | CPM_CR_FLG; - do { - __asm__ __volatile__("eieio"); - } while (cp->cp_cpcr & CPM_CR_FLG); - - /* Clear events and interrupts */ - i2c->i2c_i2cer = 0xff; - i2c->i2c_i2cmr = 0x00; -} - -static -void i2c_newio(i2c_state_t *state) -{ - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; - volatile iic_t *iip; - uint dpaddr; - - debug("[I2C] i2c_newio\n"); - - dpaddr = immap->im_dprambase16[PROFF_I2C_BASE / sizeof(u16)]; - iip = (iic_t *)&immap->im_dprambase[dpaddr]; - state->rx_idx = 0; - state->tx_idx = 0; - state->rxbd = (void *)&immap->im_dprambase[iip->iic_rbase]; - state->txbd = (void *)&immap->im_dprambase[iip->iic_tbase]; - state->tx_space = MAX_TX_SPACE; - state->tx_buf = (uchar *)state->txbd + NUM_TX_BDS * sizeof(I2C_BD); - state->err_cb = NULL; - state->cb_data = NULL; - - debug("[I2C] rxbd = %08x\n", (int)state->rxbd); - debug("[I2C] txbd = %08x\n", (int)state->txbd); - debug("[I2C] tx_buf = %08x\n", (int)state->tx_buf); - - /* clear the buffer memory */ - memset((char *) state->tx_buf, 0, MAX_TX_SPACE); -} - -static -int i2c_send(i2c_state_t *state, - unsigned char address, - unsigned char secondary_address, - unsigned int flags, unsigned short size, unsigned char *dataout) -{ - volatile I2C_BD *txbd; - int i, j; - - debug("[I2C] i2c_send add=%02d sec=%02d flag=%02d size=%d\n", - address, secondary_address, flags, size); - - /* trying to send message larger than BD */ - if (size > I2C_RXTX_LEN) - return I2CERR_MSG_TOO_LONG; - - /* no more free bds */ - if (state->tx_idx >= NUM_TX_BDS || state->tx_space < (2 + size)) - return I2CERR_NO_BUFFERS; - - txbd = (I2C_BD *)state->txbd; - txbd->addr = state->tx_buf; - - debug("[I2C] txbd = %08x\n", (int) txbd); - - if (flags & I2CF_START_COND) { - debug("[I2C] Formatting addresses...\n"); - if (flags & I2CF_ENABLE_SECONDARY) { - /* Length of message plus dest addresses */ - txbd->length = size + 2; - txbd->addr[0] = address << 1; - txbd->addr[1] = secondary_address; - i = 2; - } else { - /* Length of message plus dest address */ - txbd->length = size + 1; - /* Write destination address to BD */ - txbd->addr[0] = address << 1; - i = 1; - } - } else { - txbd->length = size; /* Length of message */ - i = 0; - } - - /* set up txbd */ - txbd->status = BD_SC_READY; - if (flags & I2CF_START_COND) - txbd->status |= BD_I2C_TX_START; - if (flags & I2CF_STOP_COND) - txbd->status |= BD_SC_LAST | BD_SC_WRAP; - - /* Copy data to send into buffer */ - debug("[I2C] copy data...\n"); - for (j = 0; j < size; i++, j++) - txbd->addr[i] = dataout[j]; - - debug("[I2C] txbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n", - txbd->length, txbd->status, txbd->addr[0], txbd->addr[1]); - - /* advance state */ - state->tx_buf += txbd->length; - state->tx_space -= txbd->length; - state->tx_idx++; - state->txbd = (void *) (txbd + 1); - - return 0; -} - -static -int i2c_receive(i2c_state_t *state, - unsigned char address, - unsigned char secondary_address, - unsigned int flags, - unsigned short size_to_expect, unsigned char *datain) -{ - volatile I2C_BD *rxbd, *txbd; - - debug("[I2C] i2c_receive %02d %02d %02d\n", address, - secondary_address, flags); - - /* Expected to receive too much */ - if (size_to_expect > I2C_RXTX_LEN) - return I2CERR_MSG_TOO_LONG; - - /* no more free bds */ - if (state->tx_idx >= NUM_TX_BDS || state->rx_idx >= NUM_RX_BDS - || state->tx_space < 2) - return I2CERR_NO_BUFFERS; - - rxbd = (I2C_BD *) state->rxbd; - txbd = (I2C_BD *) state->txbd; - - debug("[I2C] rxbd = %08x\n", (int) rxbd); - debug("[I2C] txbd = %08x\n", (int) txbd); - - txbd->addr = state->tx_buf; - - /* set up TXBD for destination address */ - if (flags & I2CF_ENABLE_SECONDARY) { - txbd->length = 2; - txbd->addr[0] = address << 1; /* Write data */ - txbd->addr[1] = secondary_address; /* Internal address */ - txbd->status = BD_SC_READY; - } else { - txbd->length = 1 + size_to_expect; - txbd->addr[0] = (address << 1) | 0x01; - txbd->status = BD_SC_READY; - memset(&txbd->addr[1], 0, txbd->length); - } - - /* set up rxbd for reception */ - rxbd->status = BD_SC_EMPTY; - rxbd->length = size_to_expect; - rxbd->addr = datain; - - txbd->status |= BD_I2C_TX_START; - if (flags & I2CF_STOP_COND) { - txbd->status |= BD_SC_LAST | BD_SC_WRAP; - rxbd->status |= BD_SC_WRAP; - } - - debug("[I2C] txbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n", - txbd->length, txbd->status, txbd->addr[0], txbd->addr[1]); - debug("[I2C] rxbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n", - rxbd->length, rxbd->status, rxbd->addr[0], rxbd->addr[1]); - - /* advance state */ - state->tx_buf += txbd->length; - state->tx_space -= txbd->length; - state->tx_idx++; - state->txbd = (void *) (txbd + 1); - state->rx_idx++; - state->rxbd = (void *) (rxbd + 1); - - return 0; -} - - -static -int i2c_doio(i2c_state_t *state) -{ - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; - volatile iic_t *iip; - volatile i2c8260_t *i2c = (i2c8260_t *)&immap->im_i2c; - volatile I2C_BD *txbd, *rxbd; - int n, i, b, rxcnt = 0, rxtimeo = 0, txcnt = 0, txtimeo = 0, rc = 0; - uint dpaddr; - - debug("[I2C] i2c_doio\n"); - - if (state->tx_idx <= 0 && state->rx_idx <= 0) { - debug("[I2C] No I/O is queued\n"); - return I2CERR_QUEUE_EMPTY; - } - - dpaddr = immap->im_dprambase16[PROFF_I2C_BASE / sizeof(u16)]; - iip = (iic_t *)&immap->im_dprambase[dpaddr]; - iip->iic_rbptr = iip->iic_rbase; - iip->iic_tbptr = iip->iic_tbase; - - /* Enable I2C */ - debug("[I2C] Enabling I2C...\n"); - i2c->i2c_i2mod |= 0x01; - - /* Begin transmission */ - i2c->i2c_i2com |= 0x80; - - /* Loop until transmit & receive completed */ - - n = state->tx_idx; - - if (n > 0) { - - txbd = ((I2C_BD *) state->txbd) - n; - for (i = 0; i < n; i++) { - txtimeo += TOUT_LOOP * txbd->length; - txbd++; - } - - txbd--; /* wait until last in list is done */ - - debug("[I2C] Transmitting...(txbd=0x%08lx)\n", - (ulong) txbd); - - udelay(START_DELAY_US); /* give it time to start */ - while ((txbd->status & BD_SC_READY) && (++txcnt < txtimeo)) { - udelay(DELAY_US); - if (ctrlc()) - return -1; - __asm__ __volatile__("eieio"); - } - } - - n = state->rx_idx; - - if (txcnt < txtimeo && n > 0) { - - rxbd = ((I2C_BD *) state->rxbd) - n; - for (i = 0; i < n; i++) { - rxtimeo += TOUT_LOOP * rxbd->length; - rxbd++; - } - - rxbd--; /* wait until last in list is done */ - - debug("[I2C] Receiving...(rxbd=0x%08lx)\n", (ulong) rxbd); - - udelay(START_DELAY_US); /* give it time to start */ - while ((rxbd->status & BD_SC_EMPTY) && (++rxcnt < rxtimeo)) { - udelay(DELAY_US); - if (ctrlc()) - return -1; - __asm__ __volatile__("eieio"); - } - } - - /* Turn off I2C */ - i2c->i2c_i2mod &= ~0x01; - - n = state->tx_idx; - - if (n > 0) { - for (i = 0; i < n; i++) { - txbd = ((I2C_BD *) state->txbd) - (n - i); - b = txbd->status & BD_I2C_TX_ERR; - if (b != 0) { - if (state->err_cb != NULL) - (*state->err_cb) (I2CECB_TX_ERR | b, - i, state->cb_data); - if (rc == 0) - rc = I2CERR_IO_ERROR; - } - } - } - - n = state->rx_idx; - - if (n > 0) { - for (i = 0; i < n; i++) { - rxbd = ((I2C_BD *) state->rxbd) - (n - i); - b = rxbd->status & BD_I2C_RX_ERR; - if (b != 0) { - if (state->err_cb != NULL) - (*state->err_cb) (I2CECB_RX_ERR | b, - i, state->cb_data); - if (rc == 0) - rc = I2CERR_IO_ERROR; - } - } - } - - if ((txtimeo > 0 && txcnt >= txtimeo) || - (rxtimeo > 0 && rxcnt >= rxtimeo)) { - if (state->err_cb != NULL) - (*state->err_cb) (I2CECB_TIMEOUT, -1, state->cb_data); - if (rc == 0) - rc = I2CERR_TIMEOUT; - } - - return rc; -} - -static void i2c_probe_callback(int flags, int xnum, void *data) -{ - /* - * the only acceptable errors are a transmit NAK or a receive - * overrun - tx NAK means the device does not exist, rx OV - * means the device must have responded to the slave address - * even though the transfer failed - */ - if (flags == (I2CECB_TX_ERR | I2CECB_TX_NAK)) - *(int *) data |= 1; - if (flags == (I2CECB_RX_ERR | I2CECB_RX_OV)) - *(int *) data |= 2; -} - -int i2c_probe(uchar chip) -{ - i2c_state_t state; - int rc, err_flag; - uchar buf[1]; - - i2c_newio(&state); - - state.err_cb = i2c_probe_callback; - state.cb_data = (void *) &err_flag; - err_flag = 0; - - rc = i2c_receive(&state, chip, 0, I2CF_START_COND | I2CF_STOP_COND, 1, - buf); - - if (rc != 0) - return rc; /* probe failed */ - - rc = i2c_doio(&state); - - if (rc == 0) - return 0; /* device exists - read succeeded */ - - if (rc == I2CERR_TIMEOUT) - return -1; /* device does not exist - timeout */ - - if (rc != I2CERR_IO_ERROR || err_flag == 0) - return rc; /* probe failed */ - - if (err_flag & 1) - return -1; /* device does not exist - had transmit NAK */ - - return 0; /* device exists - had receive overrun */ -} - - -int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) -{ - i2c_state_t state; - uchar xaddr[4]; - int rc; - - xaddr[0] = (addr >> 24) & 0xFF; - xaddr[1] = (addr >> 16) & 0xFF; - xaddr[2] = (addr >> 8) & 0xFF; - xaddr[3] = addr & 0xFF; - -#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW - /* - * EEPROM chips that implement "address overflow" are ones - * like Catalyst 24WC04/08/16 which has 9/10/11 bits of address - * and the extra bits end up in the "chip address" bit slots. - * This makes a 24WC08 (1Kbyte) chip look like four 256 byte - * chips. - * - * Note that we consider the length of the address field to still - * be one byte because the extra address bits are hidden in the - * chip address. - */ - chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW); -#endif - - i2c_newio(&state); - - rc = i2c_send(&state, chip, 0, I2CF_START_COND, alen, - &xaddr[4 - alen]); - if (rc != 0) { - printf("i2c_read: i2c_send failed (%d)\n", rc); - return 1; - } - - rc = i2c_receive(&state, chip, 0, I2CF_STOP_COND, len, buffer); - if (rc != 0) { - printf("i2c_read: i2c_receive failed (%d)\n", rc); - return 1; - } - - rc = i2c_doio(&state); - if (rc != 0) { - printf("i2c_read: i2c_doio failed (%d)\n", rc); - return 1; - } - return 0; -} - -int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) -{ - i2c_state_t state; - uchar xaddr[4]; - int rc; - - xaddr[0] = (addr >> 24) & 0xFF; - xaddr[1] = (addr >> 16) & 0xFF; - xaddr[2] = (addr >> 8) & 0xFF; - xaddr[3] = addr & 0xFF; - -#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW - /* - * EEPROM chips that implement "address overflow" are ones - * like Catalyst 24WC04/08/16 which has 9/10/11 bits of address - * and the extra bits end up in the "chip address" bit slots. - * This makes a 24WC08 (1Kbyte) chip look like four 256 byte - * chips. - * - * Note that we consider the length of the address field to still - * be one byte because the extra address bits are hidden in the - * chip address. - */ - chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW); -#endif - - i2c_newio(&state); - - rc = i2c_send(&state, chip, 0, I2CF_START_COND, alen, - &xaddr[4 - alen]); - if (rc != 0) { - printf("i2c_write: first i2c_send failed (%d)\n", rc); - return 1; - } - - rc = i2c_send(&state, 0, 0, I2CF_STOP_COND, len, buffer); - if (rc != 0) { - printf("i2c_write: second i2c_send failed (%d)\n", rc); - return 1; - } - - rc = i2c_doio(&state); - if (rc != 0) { - printf("i2c_write: i2c_doio failed (%d)\n", rc); - return 1; - } - return 0; -} - -#if defined(CONFIG_I2C_MULTI_BUS) -/* - * Functions for multiple I2C bus handling - */ -unsigned int i2c_get_bus_num(void) -{ - return i2c_bus_num; -} - -int i2c_set_bus_num(unsigned int bus) -{ - if (bus >= CONFIG_SYS_MAX_I2C_BUS) - return -1; - i2c_bus_num = bus; - return 0; -} - -#endif /* CONFIG_I2C_MULTI_BUS */ -#endif /* CONFIG_HARD_I2C */ diff --git a/arch/powerpc/cpu/mpc8xx/Makefile b/arch/powerpc/cpu/mpc8xx/Makefile index 6f81fee571..fc91a054f0 100644 --- a/arch/powerpc/cpu/mpc8xx/Makefile +++ b/arch/powerpc/cpu/mpc8xx/Makefile @@ -14,7 +14,6 @@ obj-y += cpu.o obj-y += cpu_init.o obj-y += fec.o obj-$(CONFIG_OF_LIBFDT) += fdt.o -obj-y += i2c.o obj-y += interrupts.o obj-y += scc.o obj-y += serial.o diff --git a/arch/powerpc/cpu/mpc8xx/i2c.c b/arch/powerpc/cpu/mpc8xx/i2c.c deleted file mode 100644 index 54d5cb5130..0000000000 --- a/arch/powerpc/cpu/mpc8xx/i2c.c +++ /dev/null @@ -1,672 +0,0 @@ -/* - * (C) Copyright 2000 - * Paolo Scaffardi, AIRVENT SAM s.p.a - RIMINI(ITALY), arsenio@tin.it - * - * (C) Copyright 2000 Sysgo Real-Time Solutions, GmbH - * Marius Groeger - * - * SPDX-License-Identifier: GPL-2.0+ - * - * Back ported to the 8xx platform (from the 8260 platform) by - * Murray.Jensen@cmst.csiro.au, 27-Jan-01. - */ - -#include -#include - -#ifdef CONFIG_HARD_I2C - -#include -#include - -DECLARE_GLOBAL_DATA_PTR; - -/* tx/rx timeout (we need the i2c early, so we don't use get_timer()) */ -#define TOUT_LOOP 1000000 - -#define NUM_RX_BDS 4 -#define NUM_TX_BDS 4 -#define MAX_TX_SPACE 256 -#define I2C_RXTX_LEN 128 /* maximum tx/rx buffer length */ - -typedef struct I2C_BD { - unsigned short status; - unsigned short length; - unsigned char *addr; -} I2C_BD; - -#define BD_I2C_TX_START 0x0400 /* special status for i2c: Start condition */ - -#define BD_I2C_TX_CL 0x0001 /* collision error */ -#define BD_I2C_TX_UN 0x0002 /* underflow error */ -#define BD_I2C_TX_NAK 0x0004 /* no acknowledge error */ -#define BD_I2C_TX_ERR (BD_I2C_TX_NAK|BD_I2C_TX_UN|BD_I2C_TX_CL) - -#define BD_I2C_RX_ERR BD_SC_OV - -typedef void (*i2c_ecb_t) (int, int); /* error callback function */ - -/* This structure keeps track of the bd and buffer space usage. */ -typedef struct i2c_state { - int rx_idx; /* index to next free Rx BD */ - int tx_idx; /* index to next free Tx BD */ - void *rxbd; /* pointer to next free Rx BD */ - void *txbd; /* pointer to next free Tx BD */ - int tx_space; /* number of Tx bytes left */ - unsigned char *tx_buf; /* pointer to free Tx area */ - i2c_ecb_t err_cb; /* error callback function */ -} i2c_state_t; - - -/* flags for i2c_send() and i2c_receive() */ -#define I2CF_ENABLE_SECONDARY 0x01 /* secondary_address is valid */ -#define I2CF_START_COND 0x02 /* tx: generate start condition */ -#define I2CF_STOP_COND 0x04 /* tx: generate stop condition */ - -/* return codes */ -#define I2CERR_NO_BUFFERS 0x01 /* no more BDs or buffer space */ -#define I2CERR_MSG_TOO_LONG 0x02 /* tried to send/receive to much data */ -#define I2CERR_TIMEOUT 0x03 /* timeout in i2c_doio() */ -#define I2CERR_QUEUE_EMPTY 0x04 /* i2c_doio called without send/receive */ - -/* error callback flags */ -#define I2CECB_RX_ERR 0x10 /* this is a receive error */ -#define I2CECB_RX_ERR_OV 0x02 /* receive overrun error */ -#define I2CECB_RX_MASK 0x0f /* mask for error bits */ -#define I2CECB_TX_ERR 0x20 /* this is a transmit error */ -#define I2CECB_TX_CL 0x01 /* transmit collision error */ -#define I2CECB_TX_UN 0x02 /* transmit underflow error */ -#define I2CECB_TX_NAK 0x04 /* transmit no ack error */ -#define I2CECB_TX_MASK 0x0f /* mask for error bits */ -#define I2CECB_TIMEOUT 0x40 /* this is a timeout error */ - -/* - * Returns the best value of I2BRG to meet desired clock speed of I2C with - * input parameters (clock speed, filter, and predivider value). - * It returns computer speed value and the difference between it and desired - * speed. - */ -static inline int -i2c_roundrate(int hz, int speed, int filter, int modval, - int *brgval, int *totspeed) -{ - int moddiv = 1 << (5 - (modval & 3)), brgdiv, div; - - debug("\t[I2C] trying hz=%d, speed=%d, filter=%d, modval=%d\n", - hz, speed, filter, modval); - - div = moddiv * speed; - brgdiv = (hz + div - 1) / div; - - debug("\t\tmoddiv=%d, brgdiv=%d\n", moddiv, brgdiv); - - *brgval = ((brgdiv + 1) / 2) - 3 - (2 * filter); - - if ((*brgval < 0) || (*brgval > 255)) { - debug("\t\trejected brgval=%d\n", *brgval); - return -1; - } - - brgdiv = 2 * (*brgval + 3 + (2 * filter)); - div = moddiv * brgdiv; - *totspeed = hz / div; - - debug("\t\taccepted brgval=%d, totspeed=%d\n", *brgval, *totspeed); - - return 0; -} - -/* - * Sets the I2C clock predivider and divider to meet required clock speed. - */ -static int i2c_setrate(int hz, int speed) -{ - immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - volatile i2c8xx_t *i2c = (i2c8xx_t *) & immap->im_i2c; - int brgval, - modval, /* 0-3 */ - bestspeed_diff = speed, - bestspeed_brgval = 0, - bestspeed_modval = 0, - bestspeed_filter = 0, - totspeed, - filter = 0; /* Use this fixed value */ - - for (modval = 0; modval < 4; modval++) { - if (i2c_roundrate - (hz, speed, filter, modval, &brgval, &totspeed) == 0) { - int diff = speed - totspeed; - - if ((diff >= 0) && (diff < bestspeed_diff)) { - bestspeed_diff = diff; - bestspeed_modval = modval; - bestspeed_brgval = brgval; - bestspeed_filter = filter; - } - } - } - - debug("[I2C] Best is:\n"); - debug("[I2C] CPU=%dhz RATE=%d F=%d I2MOD=%08x I2BRG=%08x DIFF=%dhz\n", - hz, - speed, - bestspeed_filter, - bestspeed_modval, - bestspeed_brgval, - bestspeed_diff); - - i2c->i2c_i2mod |= - ((bestspeed_modval & 3) << 1) | (bestspeed_filter << 3); - i2c->i2c_i2brg = bestspeed_brgval & 0xff; - - debug("[I2C] i2mod=%08x i2brg=%08x\n", - i2c->i2c_i2mod, - i2c->i2c_i2brg); - - return 1; -} - -void i2c_init(int speed, int slaveaddr) -{ - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - volatile cpm8xx_t *cp = (cpm8xx_t *)&immap->im_cpm; - volatile i2c8xx_t *i2c = (i2c8xx_t *)&immap->im_i2c; - volatile iic_t *iip = (iic_t *)&cp->cp_dparam[PROFF_IIC]; - ulong rbase, tbase; - volatile I2C_BD *rxbd, *txbd; - uint dpaddr; - -#ifdef CONFIG_SYS_I2C_INIT_BOARD - /* call board specific i2c bus reset routine before accessing the */ - /* environment, which might be in a chip on that bus. For details */ - /* about this problem see doc/I2C_Edge_Conditions. */ - i2c_init_board(); -#endif - -#ifdef CONFIG_SYS_I2C_UCODE_PATCH - iip = (iic_t *)&cp->cp_dpmem[iip->iic_rpbase]; -#else - /* Disable relocation */ - iip->iic_rpbase = 0; -#endif - - dpaddr = CPM_I2C_BASE; - - /* - * initialise data in dual port ram: - * - * dpaddr->rbase -> rx BD (NUM_RX_BDS * sizeof(I2C_BD) bytes) - * tbase -> tx BD (NUM_TX_BDS * sizeof(I2C_BD) bytes) - * tx buffer (MAX_TX_SPACE bytes) - */ - - rbase = dpaddr; - tbase = rbase + NUM_RX_BDS * sizeof(I2C_BD); - - /* Initialize Port B I2C pins. */ - cp->cp_pbpar |= 0x00000030; - cp->cp_pbdir |= 0x00000030; - cp->cp_pbodr |= 0x00000030; - - /* Disable interrupts */ - i2c->i2c_i2mod = 0x00; - i2c->i2c_i2cmr = 0x00; - i2c->i2c_i2cer = 0xff; - i2c->i2c_i2add = slaveaddr; - - /* - * Set the I2C BRG Clock division factor from desired i2c rate - * and current CPU rate (we assume sccr dfbgr field is 0; - * divide BRGCLK by 1) - */ - debug("[I2C] Setting rate...\n"); - i2c_setrate(gd->cpu_clk, CONFIG_SYS_I2C_SPEED); - - /* Set I2C controller in master mode */ - i2c->i2c_i2com = 0x01; - - /* Set SDMA bus arbitration level to 5 (SDCR) */ - immap->im_siu_conf.sc_sdcr = 0x0001; - - /* Initialize Tx/Rx parameters */ - iip->iic_rbase = rbase; - iip->iic_tbase = tbase; - rxbd = (I2C_BD *) ((unsigned char *) &cp->cp_dpmem[iip->iic_rbase]); - txbd = (I2C_BD *) ((unsigned char *) &cp->cp_dpmem[iip->iic_tbase]); - - debug("[I2C] rbase = %04x\n", iip->iic_rbase); - debug("[I2C] tbase = %04x\n", iip->iic_tbase); - debug("[I2C] rxbd = %08x\n", (int)rxbd); - debug("[I2C] txbd = %08x\n", (int)txbd); - - /* Set big endian byte order */ - iip->iic_tfcr = 0x10; - iip->iic_rfcr = 0x10; - - /* Set maximum receive size. */ - iip->iic_mrblr = I2C_RXTX_LEN; - -#ifdef CONFIG_SYS_I2C_UCODE_PATCH - /* - * Initialize required parameters if using microcode patch. - */ - iip->iic_rbptr = iip->iic_rbase; - iip->iic_tbptr = iip->iic_tbase; - iip->iic_rstate = 0; - iip->iic_tstate = 0; -#else - cp->cp_cpcr = mk_cr_cmd(CPM_CR_CH_I2C, CPM_CR_INIT_TRX) | CPM_CR_FLG; - do { - __asm__ __volatile__("eieio"); - } while (cp->cp_cpcr & CPM_CR_FLG); -#endif - - /* Clear events and interrupts */ - i2c->i2c_i2cer = 0xff; - i2c->i2c_i2cmr = 0x00; -} - -static void i2c_newio(i2c_state_t *state) -{ - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; - volatile cpm8xx_t *cp = (cpm8xx_t *)&immap->im_cpm; - volatile iic_t *iip = (iic_t *)&cp->cp_dparam[PROFF_IIC]; - - debug("[I2C] i2c_newio\n"); - -#ifdef CONFIG_SYS_I2C_UCODE_PATCH - iip = (iic_t *)&cp->cp_dpmem[iip->iic_rpbase]; -#endif - state->rx_idx = 0; - state->tx_idx = 0; - state->rxbd = (void *)&cp->cp_dpmem[iip->iic_rbase]; - state->txbd = (void *)&cp->cp_dpmem[iip->iic_tbase]; - state->tx_space = MAX_TX_SPACE; - state->tx_buf = (uchar *)state->txbd + NUM_TX_BDS * sizeof(I2C_BD); - state->err_cb = NULL; - - debug("[I2C] rxbd = %08x\n", (int)state->rxbd); - debug("[I2C] txbd = %08x\n", (int)state->txbd); - debug("[I2C] tx_buf = %08x\n", (int)state->tx_buf); - - /* clear the buffer memory */ - memset((char *)state->tx_buf, 0, MAX_TX_SPACE); -} - -static int -i2c_send(i2c_state_t *state, - unsigned char address, - unsigned char secondary_address, - unsigned int flags, unsigned short size, unsigned char *dataout) -{ - volatile I2C_BD *txbd; - int i, j; - - debug("[I2C] i2c_send add=%02d sec=%02d flag=%02d size=%d\n", - address, secondary_address, flags, size); - - /* trying to send message larger than BD */ - if (size > I2C_RXTX_LEN) - return I2CERR_MSG_TOO_LONG; - - /* no more free bds */ - if (state->tx_idx >= NUM_TX_BDS || state->tx_space < (2 + size)) - return I2CERR_NO_BUFFERS; - - txbd = (I2C_BD *) state->txbd; - txbd->addr = state->tx_buf; - - debug("[I2C] txbd = %08x\n", (int)txbd); - - if (flags & I2CF_START_COND) { - debug("[I2C] Formatting addresses...\n"); - if (flags & I2CF_ENABLE_SECONDARY) { - /* Length of msg + dest addr */ - txbd->length = size + 2; - - txbd->addr[0] = address << 1; - txbd->addr[1] = secondary_address; - i = 2; - } else { - /* Length of msg + dest addr */ - txbd->length = size + 1; - /* Write dest addr to BD */ - txbd->addr[0] = address << 1; - i = 1; - } - } else { - txbd->length = size; /* Length of message */ - i = 0; - } - - /* set up txbd */ - txbd->status = BD_SC_READY; - if (flags & I2CF_START_COND) - txbd->status |= BD_I2C_TX_START; - if (flags & I2CF_STOP_COND) - txbd->status |= BD_SC_LAST | BD_SC_WRAP; - - /* Copy data to send into buffer */ - debug("[I2C] copy data...\n"); - for(j = 0; j < size; i++, j++) - txbd->addr[i] = dataout[j]; - - debug("[I2C] txbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n", - txbd->length, - txbd->status, - txbd->addr[0], - txbd->addr[1]); - - /* advance state */ - state->tx_buf += txbd->length; - state->tx_space -= txbd->length; - state->tx_idx++; - state->txbd = (void *) (txbd + 1); - - return 0; -} - -static int -i2c_receive(i2c_state_t *state, - unsigned char address, - unsigned char secondary_address, - unsigned int flags, - unsigned short size_to_expect, unsigned char *datain) -{ - volatile I2C_BD *rxbd, *txbd; - - debug("[I2C] i2c_receive %02d %02d %02d\n", - address, secondary_address, flags); - - /* Expected to receive too much */ - if (size_to_expect > I2C_RXTX_LEN) - return I2CERR_MSG_TOO_LONG; - - /* no more free bds */ - if (state->tx_idx >= NUM_TX_BDS || state->rx_idx >= NUM_RX_BDS - || state->tx_space < 2) - return I2CERR_NO_BUFFERS; - - rxbd = (I2C_BD *) state->rxbd; - txbd = (I2C_BD *) state->txbd; - - debug("[I2C] rxbd = %08x\n", (int)rxbd); - debug("[I2C] txbd = %08x\n", (int)txbd); - - txbd->addr = state->tx_buf; - - /* set up TXBD for destination address */ - if (flags & I2CF_ENABLE_SECONDARY) { - txbd->length = 2; - txbd->addr[0] = address << 1; /* Write data */ - txbd->addr[1] = secondary_address; /* Internal address */ - txbd->status = BD_SC_READY; - } else { - txbd->length = 1 + size_to_expect; - txbd->addr[0] = (address << 1) | 0x01; - txbd->status = BD_SC_READY; - memset(&txbd->addr[1], 0, txbd->length); - } - - /* set up rxbd for reception */ - rxbd->status = BD_SC_EMPTY; - rxbd->length = size_to_expect; - rxbd->addr = datain; - - txbd->status |= BD_I2C_TX_START; - if (flags & I2CF_STOP_COND) { - txbd->status |= BD_SC_LAST | BD_SC_WRAP; - rxbd->status |= BD_SC_WRAP; - } - - debug("[I2C] txbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n", - txbd->length, - txbd->status, - txbd->addr[0], - txbd->addr[1]); - debug("[I2C] rxbd: length=0x%04x status=0x%04x addr[0]=0x%02x addr[1]=0x%02x\n", - rxbd->length, - rxbd->status, - rxbd->addr[0], - rxbd->addr[1]); - - /* advance state */ - state->tx_buf += txbd->length; - state->tx_space -= txbd->length; - state->tx_idx++; - state->txbd = (void *) (txbd + 1); - state->rx_idx++; - state->rxbd = (void *) (rxbd + 1); - - return 0; -} - - -static int i2c_doio(i2c_state_t *state) -{ - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; - volatile cpm8xx_t *cp = (cpm8xx_t *)&immap->im_cpm; - volatile i2c8xx_t *i2c = (i2c8xx_t *)&immap->im_i2c; - volatile iic_t *iip = (iic_t *)&cp->cp_dparam[PROFF_IIC]; - volatile I2C_BD *txbd, *rxbd; - volatile int j = 0; - - debug("[I2C] i2c_doio\n"); - -#ifdef CONFIG_SYS_I2C_UCODE_PATCH - iip = (iic_t *)&cp->cp_dpmem[iip->iic_rpbase]; -#endif - - if (state->tx_idx <= 0 && state->rx_idx <= 0) { - debug("[I2C] No I/O is queued\n"); - return I2CERR_QUEUE_EMPTY; - } - - iip->iic_rbptr = iip->iic_rbase; - iip->iic_tbptr = iip->iic_tbase; - - /* Enable I2C */ - debug("[I2C] Enabling I2C...\n"); - i2c->i2c_i2mod |= 0x01; - - /* Begin transmission */ - i2c->i2c_i2com |= 0x80; - - /* Loop until transmit & receive completed */ - - if (state->tx_idx > 0) { - txbd = ((I2C_BD*)state->txbd) - 1; - - debug("[I2C] Transmitting...(txbd=0x%08lx)\n", - (ulong)txbd); - - while ((txbd->status & BD_SC_READY) && (j++ < TOUT_LOOP)) { - if (ctrlc()) - return (-1); - - __asm__ __volatile__("eieio"); - } - } - - if ((state->rx_idx > 0) && (j < TOUT_LOOP)) { - rxbd = ((I2C_BD*)state->rxbd) - 1; - - debug("[I2C] Receiving...(rxbd=0x%08lx)\n", - (ulong)rxbd); - - while ((rxbd->status & BD_SC_EMPTY) && (j++ < TOUT_LOOP)) { - if (ctrlc()) - return (-1); - - __asm__ __volatile__("eieio"); - } - } - - /* Turn off I2C */ - i2c->i2c_i2mod &= ~0x01; - - if (state->err_cb != NULL) { - int n, i, b; - - /* - * if we have an error callback function, look at the - * error bits in the bd status and pass them back - */ - - if ((n = state->tx_idx) > 0) { - for (i = 0; i < n; i++) { - txbd = ((I2C_BD *) state->txbd) - (n - i); - if ((b = txbd->status & BD_I2C_TX_ERR) != 0) - (*state->err_cb) (I2CECB_TX_ERR | b, - i); - } - } - - if ((n = state->rx_idx) > 0) { - for (i = 0; i < n; i++) { - rxbd = ((I2C_BD *) state->rxbd) - (n - i); - if ((b = rxbd->status & BD_I2C_RX_ERR) != 0) - (*state->err_cb) (I2CECB_RX_ERR | b, - i); - } - } - - if (j >= TOUT_LOOP) - (*state->err_cb) (I2CECB_TIMEOUT, 0); - } - - return (j >= TOUT_LOOP) ? I2CERR_TIMEOUT : 0; -} - -static int had_tx_nak; - -static void i2c_test_callback(int flags, int xnum) -{ - if ((flags & I2CECB_TX_ERR) && (flags & I2CECB_TX_NAK)) - had_tx_nak = 1; -} - -int i2c_probe(uchar chip) -{ - i2c_state_t state; - int rc; - uchar buf[1]; - - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); - - i2c_newio(&state); - - state.err_cb = i2c_test_callback; - had_tx_nak = 0; - - rc = i2c_receive(&state, chip, 0, I2CF_START_COND | I2CF_STOP_COND, 1, - buf); - - if (rc != 0) - return (rc); - - rc = i2c_doio(&state); - - if ((rc != 0) && (rc != I2CERR_TIMEOUT)) - return (rc); - - return (had_tx_nak); -} - -int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) -{ - i2c_state_t state; - uchar xaddr[4]; - int rc; - - xaddr[0] = (addr >> 24) & 0xFF; - xaddr[1] = (addr >> 16) & 0xFF; - xaddr[2] = (addr >> 8) & 0xFF; - xaddr[3] = addr & 0xFF; - -#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW - /* - * EEPROM chips that implement "address overflow" are ones like - * Catalyst 24WC04/08/16 which has 9/10/11 bits of address and the - * extra bits end up in the "chip address" bit slots. This makes - * a 24WC08 (1Kbyte) chip look like four 256 byte chips. - * - * Note that we consider the length of the address field to still - * be one byte because the extra address bits are hidden in the - * chip address. - */ - chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW); -#endif - - i2c_newio(&state); - - rc = i2c_send(&state, chip, 0, I2CF_START_COND, alen, - &xaddr[4 - alen]); - if (rc != 0) { - printf("i2c_read: i2c_send failed (%d)\n", rc); - return 1; - } - - rc = i2c_receive(&state, chip, 0, I2CF_STOP_COND, len, buffer); - if (rc != 0) { - printf("i2c_read: i2c_receive failed (%d)\n", rc); - return 1; - } - - rc = i2c_doio(&state); - if (rc != 0) { - printf("i2c_read: i2c_doio failed (%d)\n", rc); - return 1; - } - return 0; -} - -int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) -{ - i2c_state_t state; - uchar xaddr[4]; - int rc; - - xaddr[0] = (addr >> 24) & 0xFF; - xaddr[1] = (addr >> 16) & 0xFF; - xaddr[2] = (addr >> 8) & 0xFF; - xaddr[3] = addr & 0xFF; - -#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW - /* - * EEPROM chips that implement "address overflow" are ones like - * Catalyst 24WC04/08/16 which has 9/10/11 bits of address and the - * extra bits end up in the "chip address" bit slots. This makes - * a 24WC08 (1Kbyte) chip look like four 256 byte chips. - * - * Note that we consider the length of the address field to still - * be one byte because the extra address bits are hidden in the - * chip address. - */ - chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW); -#endif - - i2c_newio(&state); - - rc = i2c_send(&state, chip, 0, I2CF_START_COND, alen, - &xaddr[4 - alen]); - if (rc != 0) { - printf("i2c_write: first i2c_send failed (%d)\n", rc); - return 1; - } - - rc = i2c_send(&state, 0, 0, I2CF_STOP_COND, len, buffer); - if (rc != 0) { - printf("i2c_write: second i2c_send failed (%d)\n", rc); - return 1; - } - - rc = i2c_doio(&state); - if (rc != 0) { - printf("i2c_write: i2c_doio failed (%d)\n", rc); - return 1; - } - return 0; -} - -#endif /* CONFIG_HARD_I2C */ diff --git a/board/freescale/m52277evb/README b/board/freescale/m52277evb/README index 92a83849ac..89e033e1c5 100644 --- a/board/freescale/m52277evb/README +++ b/board/freescale/m52277evb/README @@ -83,7 +83,6 @@ CONFIG_MCFTMR -- define to use DMA timer CONFIG_MCFPIT -- define to use PIT timer CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver -CONFIG_HARD_I2C -- define for I2C hardware support CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged CONFIG_SYS_I2C_SPEED -- define for I2C speed CONFIG_SYS_I2C_SLAVE -- define for I2C slave address diff --git a/board/freescale/m53017evb/README b/board/freescale/m53017evb/README index 224e79c46a..2fca12c417 100644 --- a/board/freescale/m53017evb/README +++ b/board/freescale/m53017evb/README @@ -91,7 +91,6 @@ CONFIG_MCFTMR -- define to use DMA timer CONFIG_MCFPIT -- define to use PIT timer CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver -CONFIG_HARD_I2C -- define for I2C hardware support CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged CONFIG_SYS_I2C_SPEED -- define for I2C speed CONFIG_SYS_I2C_SLAVE -- define for I2C slave address diff --git a/board/freescale/m5373evb/README b/board/freescale/m5373evb/README index 582e0c3d9e..757f0abdd7 100644 --- a/board/freescale/m5373evb/README +++ b/board/freescale/m5373evb/README @@ -90,7 +90,6 @@ CONFIG_MCFTMR -- define to use DMA timer CONFIG_MCFPIT -- define to use PIT timer CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver -CONFIG_HARD_I2C -- define for I2C hardware support CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged CONFIG_SYS_I2C_SPEED -- define for I2C speed CONFIG_SYS_I2C_SLAVE -- define for I2C slave address diff --git a/board/freescale/m54455evb/README b/board/freescale/m54455evb/README index c563ad99a7..4a8719333a 100644 --- a/board/freescale/m54455evb/README +++ b/board/freescale/m54455evb/README @@ -113,7 +113,6 @@ CONFIG_MCFTMR -- define to use DMA timer CONFIG_MCFPIT -- define to use PIT timer CONFIG_SYS_FSL_I2C -- define to use FSL common I2C driver -CONFIG_HARD_I2C -- define for I2C hardware support CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged CONFIG_SYS_I2C_SPEED -- define for I2C speed CONFIG_SYS_I2C_SLAVE -- define for I2C slave address diff --git a/board/freescale/m547xevb/README b/board/freescale/m547xevb/README index 30c5dedafe..ce7b27b8b2 100644 --- a/board/freescale/m547xevb/README +++ b/board/freescale/m547xevb/README @@ -98,7 +98,6 @@ CONFIG_DOS_PARTITION -- enable DOS read/write CONFIG_SLTTMR -- define to use SLT timer CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver -CONFIG_HARD_I2C -- define for I2C hardware support CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged CONFIG_SYS_I2C_SPEED -- define for I2C speed CONFIG_SYS_I2C_SLAVE -- define for I2C slave address From b7c7a2602fcbfddb091c461e59fb142ab4bfb765 Mon Sep 17 00:00:00 2001 From: Simon Glass Date: Fri, 12 May 2017 21:09:51 -0600 Subject: [PATCH 03/12] i2c: cm5200: Drop use of CONFIG_I2C_HARD Drop use of this long-deprecated option. Signed-off-by: Simon Glass --- board/cm5200/cm5200.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/board/cm5200/cm5200.c b/board/cm5200/cm5200.c index 2f55191caf..0c647bbd3d 100644 --- a/board/cm5200/cm5200.c +++ b/board/cm5200/cm5200.c @@ -214,7 +214,7 @@ static void compose_module_name(hw_id_t hw_id, char *buf) strcat(buf, tmp); } -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT) +#if defined(CONFIG_SYS_I2C_SOFT) /* * Compose string with hostname. * buf is assumed to have enough space, and be null-terminated. @@ -295,7 +295,7 @@ int board_early_init_r(void) #ifdef CONFIG_MISC_INIT_R int misc_init_r(void) { -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT) +#if defined(CONFIG_SYS_I2C_SOFT) uchar buf[6]; char str[18]; char hostname[MODULE_NAME_MAXLEN]; @@ -323,7 +323,7 @@ int misc_init_r(void) compose_hostname(hw_id, hostname); setenv("hostname", hostname); -#endif /* defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT) */ +#endif /* defined(CONFIG_SYS_I2C_SOFT) */ if (!getenv("ethaddr")) printf(LOG_PREFIX "MAC address not set, networking is not " "operational\n"); From 7a81754c96856ff913bc1878341f1fb82a6a65db Mon Sep 17 00:00:00 2001 From: Simon Glass Date: Fri, 12 May 2017 21:09:52 -0600 Subject: [PATCH 04/12] i2c: pdm360ng: Drop use of CONFIG_I2C_HARD Drop use of this long-deprecated option. Signed-off-by: Simon Glass --- board/pdm360ng/pdm360ng.c | 30 ------------------------------ 1 file changed, 30 deletions(-) diff --git a/board/pdm360ng/pdm360ng.c b/board/pdm360ng/pdm360ng.c index 9db31d3312..371bcd9e6b 100644 --- a/board/pdm360ng/pdm360ng.c +++ b/board/pdm360ng/pdm360ng.c @@ -169,36 +169,6 @@ int misc_init_r(void) clrsetbits_be32(&im->gpio.gpdat, 0x01000000, 0x00040000); #endif -#if defined(CONFIG_HARD_I2C) - if (!getenv("ethaddr")) { - uchar buf[6]; - uchar ifm_oui[3] = { 0, 2, 1, }; - int ret; - - /* I2C-0 for on-board eeprom */ - i2c_set_bus_num(CONFIG_SYS_I2C_EEPROM_BUS_NUM); - - /* Read ethaddr from EEPROM */ - ret = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, - CONFIG_SYS_I2C_EEPROM_MAC_OFFSET, 1, buf, 6); - if (ret != 0) { - printf("Error: Unable to read MAC from I2C" - " EEPROM at address %02X:%02X\n", - CONFIG_SYS_I2C_EEPROM_ADDR, - CONFIG_SYS_I2C_EEPROM_MAC_OFFSET); - return 1; - } - - /* Owned by IFM ? */ - if (memcmp(buf, ifm_oui, sizeof(ifm_oui))) { - printf("Illegal MAC address in EEPROM: %pM\n", buf); - return 1; - } - - eth_setenv_enetaddr("ethaddr", buf); - } -#endif /* defined(CONFIG_HARD_I2C) */ - return 0; } From 00fc38aec94a5ea41ec5cd5faa2bfe7b201b8e12 Mon Sep 17 00:00:00 2001 From: Simon Glass Date: Fri, 12 May 2017 21:09:53 -0600 Subject: [PATCH 05/12] i2c: keymile: Drop use of CONFIG_I2C_HARD Drop use of this long-deprecated option. Signed-off-by: Simon Glass --- board/keymile/km82xx/km82xx.c | 5 ----- board/keymile/km_arm/km_arm.c | 4 ---- 2 files changed, 9 deletions(-) diff --git a/board/keymile/km82xx/km82xx.c b/board/keymile/km82xx/km82xx.c index 51b4571d40..f5a98b33e7 100644 --- a/board/keymile/km82xx/km82xx.c +++ b/board/keymile/km82xx/km82xx.c @@ -153,13 +153,8 @@ const iop_conf_t iop_conf_tab[4][32] = { { 0, 0, 0, 0, 0, 0 }, /* PD18 */ { 0, 0, 0, 0, 0, 0 }, /* PD17 */ { 0, 0, 0, 0, 0, 0 }, /* PD16 */ -#if defined(CONFIG_HARD_I2C) - { 1, 1, 1, 0, 1, 0 }, /* PD15 I2C SDA */ - { 1, 1, 1, 0, 1, 0 }, /* PD14 I2C SCL */ -#else { 1, 0, 0, 0, 1, 1 }, /* PD15 */ { 1, 0, 0, 1, 1, 1 }, /* PD14 */ -#endif { 0, 0, 0, 0, 0, 0 }, /* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */ diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c index 079509c979..85785ffc02 100644 --- a/board/keymile/km_arm/km_arm.c +++ b/board/keymile/km_arm/km_arm.c @@ -75,10 +75,6 @@ static const u32 kwmpp_config[] = { #if defined(CONFIG_SYS_I2C_SOFT) MPP8_GPIO, /* SDA */ MPP9_GPIO, /* SCL */ -#endif -#if defined(CONFIG_HARD_I2C) - MPP8_TW_SDA, - MPP9_TW_SCK, #endif MPP10_UART0_TXD, MPP11_UART0_RXD, From 754093eb40862fbbd2450f9f0c6003fad664901c Mon Sep 17 00:00:00 2001 From: Simon Glass Date: Fri, 12 May 2017 21:09:54 -0600 Subject: [PATCH 06/12] i2c: mxc_i2c: Drop use of CONFIG_I2C_HARD Drop use of this long-deprecated option. Signed-off-by: Simon Glass --- drivers/i2c/mxc_i2c.c | 4 ---- 1 file changed, 4 deletions(-) diff --git a/drivers/i2c/mxc_i2c.c b/drivers/i2c/mxc_i2c.c index 13ec0e63b1..b68e82770b 100644 --- a/drivers/i2c/mxc_i2c.c +++ b/drivers/i2c/mxc_i2c.c @@ -69,10 +69,6 @@ DECLARE_GLOBAL_DATA_PTR; #define I2SR_IIF_CLEAR (0 << 1) #endif -#if defined(CONFIG_HARD_I2C) && !defined(CONFIG_SYS_I2C_BASE) -#error "define CONFIG_SYS_I2C_BASE to use the mxc_i2c driver" -#endif - #ifdef I2C_QUIRK_REG static u16 i2c_clk_div[60][2] = { { 20, 0x00 }, { 22, 0x01 }, { 24, 0x02 }, { 26, 0x03 }, From 64a144dcea038df2b58dd3120a880e89164af09f Mon Sep 17 00:00:00 2001 From: Simon Glass Date: Fri, 12 May 2017 21:09:55 -0600 Subject: [PATCH 07/12] i2c: omap: Modify code to work without CONFIG_I2C_HARD Drop use of this long-deprecated option. Signed-off-by: Simon Glass Suggested-by: Lokesh Vutla Reviewed-by: Tom Rini --- board/ti/am335x/board.c | 3 ++- board/ti/am43xx/board.c | 3 ++- 2 files changed, 4 insertions(+), 2 deletions(-) diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c index 3e81521399..517965c0f0 100644 --- a/board/ti/am335x/board.c +++ b/board/ti/am335x/board.c @@ -72,7 +72,8 @@ void do_board_detect(void) enable_i2c0_pin_mux(); i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); - if (ti_i2c_eeprom_am_get(-1, CONFIG_SYS_I2C_EEPROM_ADDR)) + if (ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS, + CONFIG_EEPROM_CHIP_ADDRESS)) printf("ti_i2c_eeprom_init failed\n"); } #endif diff --git a/board/ti/am43xx/board.c b/board/ti/am43xx/board.c index f633e2f85d..f44103d4d6 100644 --- a/board/ti/am43xx/board.c +++ b/board/ti/am43xx/board.c @@ -42,7 +42,8 @@ static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; #ifdef CONFIG_TI_I2C_BOARD_DETECT void do_board_detect(void) { - if (ti_i2c_eeprom_am_get(-1, CONFIG_SYS_I2C_EEPROM_ADDR)) + if (ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS, + CONFIG_EEPROM_CHIP_ADDRESS)) printf("ti_i2c_eeprom_init failed\n"); } #endif From 69153988a6f4eda44257c6bc5afac484f8f95930 Mon Sep 17 00:00:00 2001 From: Simon Glass Date: Fri, 12 May 2017 21:09:56 -0600 Subject: [PATCH 08/12] i2c: Finish dropping use of CONFIG_I2C_HARD Drop use of this long-deprecated option. Signed-off-by: Simon Glass Reviewed-by: Tom Rini --- README | 16 ++++++++-------- cmd/eeprom.c | 2 -- common/board_f.c | 4 ++-- common/stdio.c | 5 +---- scripts/config_whitelist.txt | 1 - 5 files changed, 11 insertions(+), 17 deletions(-) diff --git a/README b/README index 86f0814f79..11fa84ccc4 100644 --- a/README +++ b/README @@ -2204,7 +2204,9 @@ The following options need to be configured: If you do not have i2c muxes on your board, omit this define. -- Legacy I2C Support: CONFIG_HARD_I2C +----under removal: + +- Legacy I2C Support: CONFIG_SOFT_I2C NOTE: It is intended to move drivers to CONFIG_SYS_I2C which provides the following compelling advantages: @@ -2213,14 +2215,12 @@ The following options need to be configured: - approved multibus support - better i2c mux support - ** CONFIG_HARD_I2C is now being removed ** + ** CONFIG_SOFT_I2C is now being removed ** -----under removal: - - In both cases you will need to define CONFIG_SYS_I2C_SPEED - to be the frequency (in Hz) at which you wish your i2c bus - to run and CONFIG_SYS_I2C_SLAVE to be the address of this node (ie - the CPU's i2c node address). + With CONFIG_SOFT_I2C you will need to define + CONFIG_SYS_I2C_SPEED to be the frequency (in Hz) at which you + wish your i2c bus to run and CONFIG_SYS_I2C_SLAVE to be the + address of this node (ie the CPU's i2c node address). Now, the u-boot i2c code for the mpc8xx (arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node diff --git a/cmd/eeprom.c b/cmd/eeprom.c index 0a0e4a2c1c..e43566bc56 100644 --- a/cmd/eeprom.c +++ b/cmd/eeprom.c @@ -73,11 +73,9 @@ void eeprom_init(int bus) #endif /* I2C EEPROM */ -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C) #if defined(CONFIG_SYS_I2C) if (bus >= 0) i2c_set_bus_num(bus); -#endif i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); #endif } diff --git a/common/board_f.c b/common/board_f.c index d9431ee79a..eed3e7be2a 100644 --- a/common/board_f.c +++ b/common/board_f.c @@ -184,7 +184,7 @@ __weak int dram_init_banksize(void) return 0; } -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C) +#if defined(CONFIG_SYS_I2C) static int init_func_i2c(void) { puts("I2C: "); @@ -765,7 +765,7 @@ static const init_fnc_t init_sequence_f[] = { misc_init_f, #endif INIT_FUNC_WATCHDOG_RESET -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C) +#if defined(CONFIG_SYS_I2C) init_func_i2c, #endif #if defined(CONFIG_HARD_SPI) diff --git a/common/stdio.c b/common/stdio.c index 4d30017530..ee4f0bda9e 100644 --- a/common/stdio.c +++ b/common/stdio.c @@ -21,7 +21,7 @@ #include #endif -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C) +#if defined(CONFIG_SYS_I2C) #include #endif @@ -346,9 +346,6 @@ int stdio_add_devices(void) #ifdef CONFIG_SYS_I2C i2c_init_all(); #else -#if defined(CONFIG_HARD_I2C) - i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); -#endif #endif #ifdef CONFIG_DM_VIDEO /* diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt index 7646bb6842..da37e49c83 100644 --- a/scripts/config_whitelist.txt +++ b/scripts/config_whitelist.txt @@ -1134,7 +1134,6 @@ CONFIG_G_DNL_UMS_VENDOR_NUM CONFIG_H264_FREQ CONFIG_H8300 CONFIG_HALEAKALA -CONFIG_HARD_I2C CONFIG_HARD_SPI CONFIG_HASH_VERIFY CONFIG_HAS_DATAFLASH From b238c9dce5e487092531fb6e61c4d9f334f86686 Mon Sep 17 00:00:00 2001 From: Simon Glass Date: Fri, 12 May 2017 21:09:57 -0600 Subject: [PATCH 09/12] i2c: README: Drop CONFIG_SYS_I2C_INIT_MPC5XXX This option is not used in U-Boot. Drop it. Signed-off-by: Simon Glass --- README | 2 -- 1 file changed, 2 deletions(-) diff --git a/README b/README index 11fa84ccc4..9f9265dc6d 100644 --- a/README +++ b/README @@ -2228,8 +2228,6 @@ The following options need to be configured: eg, MPC823e User's Manual p.16-473). So, set CONFIG_SYS_I2C_SLAVE to 0. - CONFIG_SYS_I2C_INIT_MPC5XXX - When a board is reset during an i2c bus transfer chips might think that the current transfer is still in progress. Reset the slave devices by sending start From b0103f33b45286eef53239d3c80e21d7eafd9cb4 Mon Sep 17 00:00:00 2001 From: Simon Glass Date: Fri, 12 May 2017 21:09:58 -0600 Subject: [PATCH 10/12] i2c: Drop CONFIG_SYS_I2C_BOARD_LATE_INIT This option is not used by any boards. Drop it. Signed-off-by: Simon Glass --- README | 11 ----------- drivers/i2c/fsl_i2c.c | 9 --------- drivers/i2c/fti2c010.c | 9 --------- include/i2c.h | 3 --- scripts/config_whitelist.txt | 1 - 5 files changed, 33 deletions(-) diff --git a/README b/README index 9f9265dc6d..96ce6289ea 100644 --- a/README +++ b/README @@ -2323,17 +2323,6 @@ The following options need to be configured: custom i2c_init_board() routine in boards/xxx/board.c is run early in the boot sequence. - CONFIG_SYS_I2C_BOARD_LATE_INIT - - An alternative to CONFIG_SYS_I2C_INIT_BOARD. If this option is - defined a custom i2c_board_late_init() routine in - boards/xxx/board.c is run AFTER the operations in i2c_init() - is completed. This callpoint can be used to unreset i2c bus - using CPU i2c controller register accesses for CPUs whose i2c - controller provide such a method. It is called at the end of - i2c_init() to allow i2c_init operations to setup the i2c bus - controller on the CPU (e.g. setting bus speed & slave address). - CONFIG_I2CFAST (PPC405GP|PPC405EP only) This option enables configuration of bi_iic_fast[] flags diff --git a/drivers/i2c/fsl_i2c.c b/drivers/i2c/fsl_i2c.c index a1406baa87..ff3dc25927 100644 --- a/drivers/i2c/fsl_i2c.c +++ b/drivers/i2c/fsl_i2c.c @@ -284,15 +284,6 @@ static void __i2c_init(const struct fsl_i2c_base *base, int speed, int break; } - -#ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT - /* Call board specific i2c bus reset routine AFTER the bus has been - * initialized. Use either this callpoint or i2c_init_board; - * which is called before i2c_init operations. - * For details about this problem see doc/I2C_Edge_Conditions. - */ - i2c_board_late_init(); -#endif } static int diff --git a/drivers/i2c/fti2c010.c b/drivers/i2c/fti2c010.c index b35d0d2d9c..4da959fa53 100644 --- a/drivers/i2c/fti2c010.c +++ b/drivers/i2c/fti2c010.c @@ -146,15 +146,6 @@ static void fti2c010_init(struct i2c_adapter *adap, int speed, int slaveaddr) set_i2c_bus_speed(chip, speed); /* slave init, don't care */ - -#ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT - /* Call board specific i2c bus reset routine AFTER the bus has been - * initialized. Use either this callpoint or i2c_init_board; - * which is called before fti2c010_init operations. - * For details about this problem see doc/I2C_Edge_Conditions. - */ - i2c_board_late_init(); -#endif } /* diff --git a/include/i2c.h b/include/i2c.h index cd7f61e1c1..a88cc7cddf 100644 --- a/include/i2c.h +++ b/include/i2c.h @@ -706,9 +706,6 @@ void i2c_early_init_f(void); #endif void i2c_init(int speed, int slaveaddr); void i2c_init_board(void); -#ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT -void i2c_board_late_init(void); -#endif #ifdef CONFIG_SYS_I2C /* diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt index da37e49c83..5cdca33f87 100644 --- a/scripts/config_whitelist.txt +++ b/scripts/config_whitelist.txt @@ -4222,7 +4222,6 @@ CONFIG_SYS_I2C_BASE2 CONFIG_SYS_I2C_BASE3 CONFIG_SYS_I2C_BASE4 CONFIG_SYS_I2C_BASE5 -CONFIG_SYS_I2C_BOARD_LATE_INIT CONFIG_SYS_I2C_BOOT_EEPROM_ADDR CONFIG_SYS_I2C_BUSES CONFIG_SYS_I2C_BUS_MAX From 213f27f3f9c89dbf32e38cb031b303193e6e8627 Mon Sep 17 00:00:00 2001 From: Simon Glass Date: Fri, 12 May 2017 21:09:59 -0600 Subject: [PATCH 11/12] Drop CONFIG_I2CFAST This option is not used in U-Boot. Drop it. Signed-off-by: Simon Glass --- README | 6 ------ common/board_r.c | 17 ----------------- scripts/config_whitelist.txt | 1 - 3 files changed, 24 deletions(-) diff --git a/README b/README index 96ce6289ea..71d8de0ba8 100644 --- a/README +++ b/README @@ -2323,12 +2323,6 @@ The following options need to be configured: custom i2c_init_board() routine in boards/xxx/board.c is run early in the boot sequence. - CONFIG_I2CFAST (PPC405GP|PPC405EP only) - - This option enables configuration of bi_iic_fast[] flags - in u-boot bd_info structure based on u-boot environment - variable "i2cfast". (see also i2cfast) - CONFIG_I2C_MULTI_BUS This option allows the use of multiple I2C buses, each of which diff --git a/common/board_r.c b/common/board_r.c index d69a33c4a3..dba2102b18 100644 --- a/common/board_r.c +++ b/common/board_r.c @@ -485,24 +485,7 @@ static int initr_env(void) /* Initialize from environment */ load_addr = getenv_ulong("loadaddr", 16, load_addr); -#if defined(CONFIG_SYS_EXTBDINFO) -#if defined(CONFIG_405GP) || defined(CONFIG_405EP) -#if defined(CONFIG_I2CFAST) - /* - * set bi_iic_fast for linux taking environment variable - * "i2cfast" into account - */ - { - char *s = getenv("i2cfast"); - if (s && ((*s == 'y') || (*s == 'Y'))) { - gd->bd->bi_iic_fast[0] = 1; - gd->bd->bi_iic_fast[1] = 1; - } - } -#endif /* CONFIG_I2CFAST */ -#endif /* CONFIG_405GP, CONFIG_405EP */ -#endif /* CONFIG_SYS_EXTBDINFO */ return 0; } diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt index 5cdca33f87..7cdfcd0a52 100644 --- a/scripts/config_whitelist.txt +++ b/scripts/config_whitelist.txt @@ -1319,7 +1319,6 @@ CONFIG_HW_ENV_SETTINGS CONFIG_HW_WATCHDOG CONFIG_HW_WATCHDOG_TIMEOUT_MS CONFIG_I2C -CONFIG_I2CFAST CONFIG_I2C_CHIPADDRESS CONFIG_I2C_CMD_TREE CONFIG_I2C_ENV_EEPROM_BUS From ce3b5d69112b1adc878e06586c1bc819414309be Mon Sep 17 00:00:00 2001 From: Simon Glass Date: Fri, 12 May 2017 21:10:00 -0600 Subject: [PATCH 12/12] Drop use of CONFIG_I2C_SOFT This option is not used in U-Boot. Drop it. Signed-off-by: Simon Glass --- README | 32 +------------------------------- 1 file changed, 1 insertion(+), 31 deletions(-) diff --git a/README b/README index 71d8de0ba8..9525199551 100644 --- a/README +++ b/README @@ -2204,37 +2204,7 @@ The following options need to be configured: If you do not have i2c muxes on your board, omit this define. -----under removal: - -- Legacy I2C Support: CONFIG_SOFT_I2C - - NOTE: It is intended to move drivers to CONFIG_SYS_I2C which - provides the following compelling advantages: - - - more than one i2c adapter is usable - - approved multibus support - - better i2c mux support - - ** CONFIG_SOFT_I2C is now being removed ** - - With CONFIG_SOFT_I2C you will need to define - CONFIG_SYS_I2C_SPEED to be the frequency (in Hz) at which you - wish your i2c bus to run and CONFIG_SYS_I2C_SLAVE to be the - address of this node (ie the CPU's i2c node address). - - Now, the u-boot i2c code for the mpc8xx - (arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node - and so its address should therefore be cleared to 0 (See, - eg, MPC823e User's Manual p.16-473). So, set - CONFIG_SYS_I2C_SLAVE to 0. - - When a board is reset during an i2c bus transfer - chips might think that the current transfer is still - in progress. Reset the slave devices by sending start - commands until the slave device responds. - - That's all that's required for CONFIG_HARD_I2C. - +- Legacy I2C Support: If you use the software i2c interface (CONFIG_SYS_I2C_SOFT) then the following macros need to be defined (examples are from include/configs/lwmon.h):