FSL DDR: Convert socrates to new DDR code.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

board/socrates/Makefile

@@ -28,10 +28,15 @@ include $(TOPDIR)/config.mk
 LIB	= $(obj)lib$(BOARD).a
 #
 
-COBJS	:= $(BOARD).o law.o tlb.o sdram.o nand.o
+COBJS-y	+= $(BOARD).o
+COBJS-y	+= law.o
+COBJS-y	+= tlb.o
+COBJS-y	+= nand.o
+COBJS-y	+= sdram.o
+COBJS-$(CONFIG_FSL_DDR2) += ddr.o
 
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
 SOBJS	:= $(addprefix $(obj),$(SOBJS))
 
 $(LIB):	$(obj).depend $(OBJS) $(SOBJS)

board/socrates/ddr.c

@@ -0,0 +1,80 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+
+static void
+get_spd(ddr2_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+	i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr2_spd_eeprom_t));
+}
+
+unsigned int fsl_ddr_get_mem_data_rate(void)
+{
+	return get_ddr_freq(0);
+}
+
+void fsl_ddr_get_spd(ddr2_spd_eeprom_t *ctrl_dimms_spd,
+		      unsigned int ctrl_num)
+{
+	unsigned int i;
+
+	if (ctrl_num) {
+		printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num);
+		return;
+	}
+
+	for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+		get_spd(&(ctrl_dimms_spd[i]), SPD_EEPROM_ADDRESS);
+	}
+}
+
+void fsl_ddr_board_options(memctl_options_t *popts, unsigned int ctrl_num)
+{
+	/*
+	 * Factors to consider for clock adjust:
+	 *	- number of chips on bus
+	 *	- position of slot
+	 *	- DDR1 vs. DDR2?
+	 *	- ???
+	 *
+	 * This needs to be determined on a board-by-board basis.
+	 *	0110	3/4 cycle late
+	 *	0111	7/8 cycle late
+	 */
+	popts->clk_adjust = 7;
+
+	/*
+	 * Factors to consider for CPO:
+	 *	- frequency
+	 *	- ddr1 vs. ddr2
+	 */
+	popts->cpo_override = 10;
+
+	/*
+	 * Factors to consider for write data delay:
+	 *	- number of DIMMs
+	 *
+	 * 1 = 1/4 clock delay
+	 * 2 = 1/2 clock delay
+	 * 3 = 3/4 clock delay
+	 * 4 = 1   clock delay
+	 * 5 = 5/4 clock delay
+	 * 6 = 3/2 clock delay
+	 */
+	popts->write_data_delay = 3;
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+}

board/socrates/sdram.c

@@ -25,6 +25,7 @@
 #include <common.h>
 #include <asm/processor.h>
 #include <asm/immap_85xx.h>
+#include <asm/fsl_ddr_sdram.h>
 #include <asm/processor.h>
 #include <asm/mmu.h>
 #include <spd_sdram.h>
@@ -80,7 +81,9 @@ phys_size_t initdram (int board_type)
 {
 	long dram_size = 0;
 #if defined(CONFIG_SPD_EEPROM)
-	dram_size = spd_sdram ();
+	dram_size = fsl_ddr_sdram();
+	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+	dram_size *= 0x100000;
 #else
 	dram_size = sdram_setup(CONFIG_DDR_DEFAULT_CL);
 #endif

include/configs/socrates.h

@@ -93,11 +93,25 @@
 #define CFG_CCSRBAR_PHYS	CFG_CCSRBAR	/* physical addr of CCSRBAR */
 #define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR	*/
 
-/*
- * DDR Setup
- */
-#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory	*/
+/* DDR Setup */
+#define CONFIG_FSL_DDR2
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
+#define CONFIG_DDR_SPD
+
+#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
+
+#define CFG_DDR_SDRAM_BASE	0x00000000
 #define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
+
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	2
+
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS	0x51	/* CTLR 0 DIMM 0 */
 
 #define CONFIG_DDR_DEFAULT_CL	30		/* CAS latency 3	*/
 
@@ -114,13 +128,6 @@
 #define CFG_DDR_CLK_CONTROL		0x03800000
 #define CFG_SDRAM_SIZE			256 /* in Megs */
 
-#define CONFIG_SPD_EEPROM	1 	/* Use SPD EEPROM for DDR setup*/
-#define SPD_EEPROM_ADDRESS	0x50		/* DDR DIMM */
-#define MPC85xx_DDR_SDRAM_CLK_CNTL	/* 85xx has clock control reg */
-
-/*
- * Flash on the Local Bus
- */
 /*
  * Flash on the LocalBus
  */