arm: socfpga: stratix10: Enable Stratix10 SoC build

Add build support for Stratix SoC

Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>

Conflicts:

	arch/arm/Kconfig
	arch/arm/mach-socfpga/Kconfig

arch/arm/Kconfig

@@ -759,10 +759,10 @@ config ARCH_SOCFPGA
 	bool "Altera SOCFPGA family"
 	select ARCH_EARLY_INIT_R
 	select ARCH_MISC_INIT
-	select CPU_V7A
+	select CPU_V7A if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
 	select DM
 	select DM_SERIAL
-	select ENABLE_ARM_SOC_BOOT0_HOOK
+	select ENABLE_ARM_SOC_BOOT0_HOOK if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
 	select OF_CONTROL
 	select SPL_LIBCOMMON_SUPPORT
 	select SPL_LIBDISK_SUPPORT
@@ -772,20 +772,22 @@ config ARCH_SOCFPGA
 	select SPL_OF_CONTROL
 	select SPL_SERIAL_SUPPORT
 	select SPL_DM_SERIAL
+	select SPL_RESET_SUPPORT
 	select SPL_SPI_FLASH_SUPPORT if SPL_SPI_SUPPORT
 	select SPL_SPI_SUPPORT if DM_SPI
 	select SPL_WATCHDOG_SUPPORT
 	select SUPPORT_SPL
 	select SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION_TYPE
 	select SYS_NS16550
-	select SYS_THUMB_BUILD
+	select SYS_THUMB_BUILD if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
+	select ARM64 if TARGET_SOCFPGA_STRATIX10
 	imply CMD_MTDPARTS
 	imply CRC32_VERIFY
 	imply DM_SPI
 	imply DM_SPI_FLASH
 	imply FAT_WRITE
-	imply HW_WATCHDOG
 	imply SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION
+	select SPL_SEPARATE_BSS if TARGET_SOCFPGA_STRATIX10
 
 config ARCH_SUNXI
 	bool "Support sunxi (Allwinner) SoCs"

arch/arm/mach-socfpga/Kconfig

@@ -20,6 +20,12 @@ config TARGET_SOCFPGA_GEN5
 	bool
 	select ALTERA_SDRAM
 
+config TARGET_SOCFPGA_STRATIX10
+	bool
+	select ARMV8_MULTIENTRY
+	select ARMV8_SPIN_TABLE
+	select ARMV8_SET_SMPEN
+
 choice
 	prompt "Altera SOCFPGA board select"
 	optional
@@ -57,6 +63,10 @@ config TARGET_SOCFPGA_SR1500
 	bool "SR1500 (Cyclone V)"
 	select TARGET_SOCFPGA_CYCLONE5
 
+config TARGET_SOCFPGA_STRATIX10_SOCDK
+	bool "Intel SOCFPGA SoCDK (Stratix 10)"
+	select TARGET_SOCFPGA_STRATIX10
+
 config TARGET_SOCFPGA_TERASIC_DE0_NANO
 	bool "Terasic DE0-Nano-Atlas (Cyclone V)"
 	select TARGET_SOCFPGA_CYCLONE5
@@ -87,12 +97,14 @@ config SYS_BOARD
 	default "sockit" if TARGET_SOCFPGA_TERASIC_SOCKIT
 	default "socrates" if TARGET_SOCFPGA_EBV_SOCRATES
 	default "sr1500" if TARGET_SOCFPGA_SR1500
+	default "stratix10-socdk" if TARGET_SOCFPGA_STRATIX10_SOCDK
 	default "vining_fpga" if TARGET_SOCFPGA_SAMTEC_VINING_FPGA
 
 config SYS_VENDOR
 	default "altera" if TARGET_SOCFPGA_ARRIA5_SOCDK
 	default "altera" if TARGET_SOCFPGA_ARRIA10_SOCDK
 	default "altera" if TARGET_SOCFPGA_CYCLONE5_SOCDK
+	default "altera" if TARGET_SOCFPGA_STRATIX10_SOCDK
 	default "devboards" if TARGET_SOCFPGA_DEVBOARDS_DBM_SOC1
 	default "ebv" if TARGET_SOCFPGA_EBV_SOCRATES
 	default "samtec" if TARGET_SOCFPGA_SAMTEC_VINING_FPGA
@@ -116,6 +128,7 @@ config SYS_CONFIG_NAME
 	default "socfpga_sockit" if TARGET_SOCFPGA_TERASIC_SOCKIT
 	default "socfpga_socrates" if TARGET_SOCFPGA_EBV_SOCRATES
 	default "socfpga_sr1500" if TARGET_SOCFPGA_SR1500
+	default "socfpga_stratix10_socdk" if TARGET_SOCFPGA_STRATIX10_SOCDK
 	default "socfpga_vining_fpga" if TARGET_SOCFPGA_SAMTEC_VINING_FPGA
 
 endif

configs/socfpga_stratix10_defconfig

@@ -0,0 +1,56 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SOCFPGA=y
+CONFIG_SYS_TEXT_BASE=0x1000
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_TARGET_SOCFPGA_STRATIX10_SOCDK=y
+CONFIG_SPL=y
+CONFIG_IDENT_STRING="socfpga_stratix10"
+CONFIG_SPL_FAT_SUPPORT=y
+CONFIG_DEFAULT_DEVICE_TREE="socfpga_stratix10_socdk"
+CONFIG_BOOTDELAY=5
+CONFIG_SPL_SPI_LOAD=y
+CONFIG_HUSH_PARSER=y
+CONFIG_SYS_PROMPT="SOCFPGA_STRATIX10 # "
+CONFIG_CMD_MEMTEST=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SPL_DM=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_DM_GPIO=y
+CONFIG_DWAPB_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_DW=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_DW=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_BAR=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_PHY_MICREL=y
+CONFIG_PHY_MICREL_KSZ90X1=y
+CONFIG_DM_ETH=y
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_DM_RESET=y
+CONFIG_SPI=y
+CONFIG_CADENCE_QSPI=y
+CONFIG_DESIGNWARE_SPI=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_DWC2=y
+CONFIG_USB_STORAGE=y
+CONFIG_USE_TINY_PRINTF=y

include/configs/socfpga_stratix10_socdk.h

@@ -0,0 +1,222 @@
+/* SPDX-License-Identifier: GPL-2.0
+ *
+ * Copyright (C) 2017-2018 Intel Corporation <www.intel.com>
+ *
+ */
+
+#ifndef __CONFIG_SOCFGPA_STRATIX10_H__
+#define __CONFIG_SOCFGPA_STRATIX10_H__
+
+#include <asm/arch/base_addr_s10.h>
+#include <asm/arch/handoff_s10.h>
+
+/*
+ * U-Boot general configurations
+ */
+#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
+#define CONFIG_LOADADDR			0x2000000
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+#define CONFIG_REMAKE_ELF
+/* sysmgr.boot_scratch_cold4 & 5 (64bit) will be used for PSCI_CPU_ON call */
+#define CPU_RELEASE_ADDR		0xFFD12210
+#define CONFIG_SYS_CACHELINE_SIZE	64
+#define CONFIG_SYS_MEM_RESERVE_SECURE	0	/* using OCRAM, not DDR */
+
+/*
+ * U-Boot console configurations
+ */
+#define CONFIG_SYS_MAXARGS		64
+#define CONFIG_SYS_CBSIZE		2048
+#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
+					sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
+
+/* Extend size of kernel image for uncompression */
+#define CONFIG_SYS_BOOTM_LEN		(32 * 1024 * 1024)
+
+/*
+ * U-Boot run time memory configurations
+ */
+#define CONFIG_SYS_INIT_RAM_ADDR	0xFFE00000
+#define CONFIG_SYS_INIT_RAM_SIZE	0x40000
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INIT_RAM_ADDR  \
+					+ CONFIG_SYS_INIT_RAM_SIZE \
+					- S10_HANDOFF_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_INIT_SP_ADDR)
+#define CONFIG_SYS_MALLOC_LEN		(5 * 1024 * 1024)
+
+/*
+ * U-Boot environment configurations
+ */
+#define CONFIG_ENV_SIZE			0x1000
+#define CONFIG_SYS_MMC_ENV_DEV		0	/* device 0 */
+#define CONFIG_ENV_OFFSET		512	/* just after the MBR */
+
+/*
+ * QSPI support
+ */
+ #ifdef CONFIG_CADENCE_QSPI
+/* Enable it if you want to use dual-stacked mode */
+#undef CONFIG_SF_DUAL_FLASH
+/*#define CONFIG_QSPI_RBF_ADDR		0x720000*/
+
+/* Flash device info */
+#define CONFIG_SF_DEFAULT_SPEED		(50000000)
+#define CONFIG_SF_DEFAULT_MODE		(SPI_MODE_3 | SPI_RX_QUAD)
+#define CONFIG_SF_DEFAULT_BUS		0
+#define CONFIG_SF_DEFAULT_CS		0
+
+/*#define CONFIG_ENV_IS_IN_SPI_FLASH*/
+#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
+#undef CONFIG_ENV_OFFSET
+#undef CONFIG_ENV_SIZE
+#define CONFIG_ENV_OFFSET		0x710000
+#define CONFIG_ENV_SIZE			(4 * 1024)
+#define CONFIG_ENV_SECT_SIZE		(4 * 1024)
+#endif /* CONFIG_ENV_IS_IN_SPI_FLASH */
+
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+#define MTDIDS_DEFAULT			"nor0=ff705000.spi.0"
+#endif /* CONFIG_SPL_BUILD */
+
+#ifndef __ASSEMBLY__
+unsigned int cm_get_qspi_controller_clk_hz(void);
+#define CONFIG_CQSPI_REF_CLK		cm_get_qspi_controller_clk_hz()
+#endif
+
+#endif /* CONFIG_CADENCE_QSPI */
+
+/*
+ * Boot arguments passed to the boot command. The value of
+ * CONFIG_BOOTARGS goes into the environment value "bootargs".
+ * Do note the value will override also the chosen node in FDT blob.
+ */
+#define CONFIG_BOOTARGS "earlycon"
+#define CONFIG_BOOTCOMMAND "run fatscript; run mmcload;run linux_qspi_enable;" \
+			   "run mmcboot"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"loadaddr=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
+	"bootfile=Image\0" \
+	"fdt_addr=8000000\0" \
+	"fdtimage=socfpga_stratix10_socdk.dtb\0" \
+	"mmcroot=/dev/mmcblk0p2\0" \
+	"mmcboot=setenv bootargs " CONFIG_BOOTARGS \
+		" root=${mmcroot} rw rootwait;" \
+		"booti ${loadaddr} - ${fdt_addr}\0" \
+	"mmcload=mmc rescan;" \
+		"load mmc 0:1 ${loadaddr} ${bootfile};" \
+		"load mmc 0:1 ${fdt_addr} ${fdtimage}\0" \
+	"linux_qspi_enable=if sf probe; then " \
+		"echo Enabling QSPI at Linux DTB...;" \
+		"fdt addr ${fdt_addr}; fdt resize;" \
+		"fdt set /soc/spi@ff8d2000 status okay;" \
+		"fdt set /soc/clkmgr/clocks/qspi_clk clock-frequency " \
+		" ${qspi_clock}; fi; \0" \
+	"scriptaddr=0x02100000\0" \
+	"scriptfile=u-boot.scr\0" \
+	"fatscript=if fatload mmc 0:1 ${scriptaddr} ${scriptfile};" \
+		   "then source ${scriptaddr}; fi\0"
+
+/*
+ * Generic Interrupt Controller Definitions
+ */
+#define CONFIG_GICV2
+
+/*
+ * External memory configurations
+ */
+#define PHYS_SDRAM_1			0x0
+#define PHYS_SDRAM_1_SIZE		(1 * 1024 * 1024 * 1024)
+#define CONFIG_SYS_SDRAM_BASE		0
+#define CONFIG_NR_DRAM_BANKS		1
+#define CONFIG_SYS_MEMTEST_START	0
+#define CONFIG_SYS_MEMTEST_END		PHYS_SDRAM_1_SIZE - 0x200000
+
+/*
+ * SDRAM controller
+ */
+#define CONFIG_ALTERA_SDRAM
+
+/*
+ * Serial / UART configurations
+ */
+#define CONFIG_SYS_NS16550_CLK		100000000
+#define CONFIG_SYS_NS16550_MEM32
+
+/*
+ * Timer & watchdog configurations
+ */
+#define COUNTER_FREQUENCY		400000000
+
+/*
+ * SDMMC configurations
+ */
+#ifdef CONFIG_CMD_MMC
+#define CONFIG_BOUNCE_BUFFER
+#define CONFIG_SYS_MMC_MAX_BLK_COUNT	256
+#endif
+/*
+ * Flash configurations
+ */
+#define CONFIG_SYS_MAX_FLASH_BANKS	1
+
+/* Ethernet on SoC (EMAC) */
+#if defined(CONFIG_CMD_NET)
+#define CONFIG_DW_ALTDESCRIPTOR
+#define CONFIG_MII
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * L4 Watchdog
+ */
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_HW_WATCHDOG
+#define CONFIG_DESIGNWARE_WATCHDOG
+#define CONFIG_DW_WDT_BASE		SOCFPGA_L4WD0_ADDRESS
+#ifndef __ASSEMBLY__
+unsigned int cm_get_l4_sys_free_clk_hz(void);
+#define CONFIG_DW_WDT_CLOCK_KHZ		(cm_get_l4_sys_free_clk_hz() / 1000)
+#endif
+#define CONFIG_WATCHDOG_TIMEOUT_MSECS	3000
+#endif
+
+/*
+ * SPL memory layout
+ *
+ * On chip RAM
+ * 0xFFE0_0000 ...... Start of OCRAM
+ * SPL code, rwdata
+ * empty space
+ * 0xFFEx_xxxx ...... Top of stack (grows down)
+ * 0xFFEy_yyyy ...... Global Data
+ * 0xFFEz_zzzz ...... Malloc prior relocation (size CONFIG_SYS_MALLOC_F_LEN)
+ * 0xFFE3_F000 ...... Hardware handdoff blob (size 4KB)
+ * 0xFFE3_FFFF ...... End of OCRAM
+ *
+ * SDRAM
+ * 0x0000_0000 ...... Start of SDRAM_1
+ * unused / empty space for image loading
+ * Size 64MB   ...... MALLOC (size CONFIG_SYS_SPL_MALLOC_SIZE)
+ * Size 1MB    ...... BSS (size CONFIG_SPL_BSS_MAX_SIZE)
+ * 0x8000_0000 ...... End of SDRAM_1 (assume 2GB)
+ *
+ */
+#define CONFIG_SPL_TEXT_BASE		CONFIG_SYS_INIT_RAM_ADDR
+#define CONFIG_SPL_MAX_SIZE		CONFIG_SYS_INIT_RAM_SIZE
+#define CONFIG_SPL_STACK		CONFIG_SYS_INIT_SP_ADDR
+#define CONFIG_SPL_BSS_MAX_SIZE		0x100000	/* 1 MB */
+#define CONFIG_SPL_BSS_START_ADDR	(PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE \
+					- CONFIG_SPL_BSS_MAX_SIZE)
+#define CONFIG_SYS_SPL_MALLOC_SIZE	(CONFIG_SYS_MALLOC_LEN)
+#define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SPL_BSS_START_ADDR \
+					- CONFIG_SYS_SPL_MALLOC_SIZE)
+#define CONFIG_SYS_SPI_U_BOOT_OFFS      0x3C00000
+
+/* SPL SDMMC boot support */
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME		"u-boot-dtb.img"
+
+#endif	/* __CONFIG_H */