drivers: misc: add Gateworks System Controller driver

Add a driver for the Gateworks System Controller used on Gateworks boards
which provides a boot watchdog, power control, temperature monitor,
and voltage ADCs.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
This commit is contained in:
Tim Harvey 2022-03-07 16:24:04 -08:00 committed by Stefano Babic
parent 6bec6c169f
commit 8479b9e6c9
5 changed files with 669 additions and 0 deletions

View File

@ -882,6 +882,12 @@ T: git https://source.denx.de/u-boot/custodians/u-boot-fsl-qoriq.git
F: drivers/watchdog/sp805_wdt.c
F: drivers/watchdog/sbsa_gwdt.c
GATEWORKS_SC
M: Tim Harvey <tharvey@gateworks.com>
S: Maintained
F: drivers/misc/gsc.c
F: include/gsc.h
I2C
M: Heiko Schocher <hs@denx.de>
S: Maintained

View File

@ -46,6 +46,14 @@ config ATSHA204A
CryptoAuthentication module found for example on the Turris Omnia
board.
config GATEWORKS_SC
bool "Gateworks System Controller Support"
depends on MISC
help
Enable access for the Gateworks System Controller used on Gateworks
boards to provide a boot watchdog, power control, temperature monitor,
voltage ADCs, and EEPROM.
config ROCKCHIP_EFUSE
bool "Rockchip e-fuse support"
depends on MISC

View File

@ -38,6 +38,7 @@ obj-$(CONFIG_FSL_IIM) += fsl_iim.o
obj-$(CONFIG_FSL_MC9SDZ60) += mc9sdz60.o
obj-$(CONFIG_FSL_SEC_MON) += fsl_sec_mon.o
obj-$(CONFIG_$(SPL_)FS_LOADER) += fs_loader.o
obj-$(CONFIG_GATEWORKS_SC) += gsc.o
obj-$(CONFIG_GDSYS_IOEP) += gdsys_ioep.o
obj-$(CONFIG_GDSYS_RXAUI_CTRL) += gdsys_rxaui_ctrl.o
obj-$(CONFIG_GDSYS_SOC) += gdsys_soc.o

633
drivers/misc/gsc.c Normal file
View File

@ -0,0 +1,633 @@
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2022 Gateworks Corporation
*/
#include <command.h>
#include <gsc.h>
#include <i2c.h>
#include <rtc.h>
#include <asm/unaligned.h>
#include <linux/delay.h>
#include <dm/device.h>
#include <dm/device-internal.h>
#include <dm/ofnode.h>
#include <dm/read.h>
#define GSC_BUSNO 0
#define GSC_SC_ADDR 0x20
#define GSC_HWMON_ADDR 0x29
#define GSC_RTC_ADDR 0x68
/* System Controller registers */
enum {
GSC_SC_CTRL0 = 0,
GSC_SC_CTRL1 = 1,
GSC_SC_TIME = 2,
GSC_SC_TIME_ADD = 6,
GSC_SC_STATUS = 10,
GSC_SC_FWCRC = 12,
GSC_SC_FWVER = 14,
GSC_SC_WP = 15,
GSC_SC_RST_CAUSE = 16,
GSC_SC_THERM_PROTECT = 19,
};
/* System Controller Control1 bits */
enum {
GSC_SC_CTRL1_SLEEP_EN = 0, /* 1 = enable sleep */
GSC_SC_CTRL1_SLEEP_ACTIVATE = 1, /* 1 = activate sleep */
GSC_SC_CTRL1_SLEEP_ADD = 2, /* 1 = latch and add sleep time */
GSC_SC_CTRL1_SLEEP_NOWAKEPB = 3, /* 1 = do not wake on sleep on button press */
GSC_SC_CTRL1_WDTIME = 4, /* 1 = 60s timeout, 0 = 30s timeout */
GSC_SC_CTRL1_WDEN = 5, /* 1 = enable, 0 = disable */
GSC_SC_CTRL1_BOOT_CHK = 6, /* 1 = enable alt boot check */
GSC_SC_CTRL1_WDDIS = 7, /* 1 = disable boot watchdog */
};
/* System Controller Interrupt bits */
enum {
GSC_SC_IRQ_PB = 0, /* Pushbutton switch */
GSC_SC_IRQ_SECURE = 1, /* Secure Key erase operation complete */
GSC_SC_IRQ_EEPROM_WP = 2, /* EEPROM write violation */
GSC_SC_IRQ_GPIO = 4, /* GPIO change */
GSC_SC_IRQ_TAMPER = 5, /* Tamper detect */
GSC_SC_IRQ_WATCHDOG = 6, /* Watchdog trip */
GSC_SC_IRQ_PBLONG = 7, /* Pushbutton long hold */
};
/* System Controller WP bits */
enum {
GSC_SC_WP_ALL = 0, /* Write Protect All EEPROM regions */
GSC_SC_WP_BOARDINFO = 1, /* Write Protect Board Info region */
};
/* System Controller Reset Cause */
enum {
GSC_SC_RST_CAUSE_VIN = 0,
GSC_SC_RST_CAUSE_PB = 1,
GSC_SC_RST_CAUSE_WDT = 2,
GSC_SC_RST_CAUSE_CPU = 3,
GSC_SC_RST_CAUSE_TEMP_LOCAL = 4,
GSC_SC_RST_CAUSE_TEMP_REMOTE = 5,
GSC_SC_RST_CAUSE_SLEEP = 6,
GSC_SC_RST_CAUSE_BOOT_WDT = 7,
GSC_SC_RST_CAUSE_BOOT_WDT_MAN = 8,
GSC_SC_RST_CAUSE_SOFT_PWR = 9,
GSC_SC_RST_CAUSE_MAX = 10,
};
#if (IS_ENABLED(CONFIG_DM_I2C))
struct gsc_priv {
int gscver;
int fwver;
int fwcrc;
struct udevice *hwmon;
struct udevice *rtc;
};
/*
* GSCv2 will fail to ACK an I2C transaction if it is busy, which can occur
* during its 1HZ timer tick while reading ADC's. When this does occur,
* it will never be busy longer than 2 back-to-back transfers so retry 3 times.
*/
static int gsc_i2c_read(struct udevice *dev, uint addr, u8 *buf, int len)
{
struct gsc_priv *priv = dev_get_priv(dev);
int retry = (priv->gscver == 3) ? 1 : 3;
int n = 0;
int ret;
while (n++ < retry) {
ret = dm_i2c_read(dev, addr, buf, len);
if (!ret)
break;
if (ret != -EREMOTEIO)
break;
mdelay(10);
}
return ret;
}
static int gsc_i2c_write(struct udevice *dev, uint addr, const u8 *buf, int len)
{
struct gsc_priv *priv = dev_get_priv(dev);
int retry = (priv->gscver == 3) ? 1 : 3;
int n = 0;
int ret;
while (n++ < retry) {
ret = dm_i2c_write(dev, addr, buf, len);
if (!ret)
break;
if (ret != -EREMOTEIO)
break;
mdelay(10);
}
return ret;
}
static struct udevice *gsc_get_dev(int busno, int slave)
{
struct udevice *dev, *bus;
int ret;
ret = uclass_get_device_by_seq(UCLASS_I2C, busno, &bus);
if (ret)
return NULL;
ret = dm_i2c_probe(bus, slave, 0, &dev);
if (ret)
return NULL;
return dev;
}
static int gsc_thermal_get_info(struct udevice *dev, u8 *outreg, int *tmax, bool *enable)
{
struct gsc_priv *priv = dev_get_priv(dev);
int ret;
u8 reg;
if (priv->gscver > 2 && priv->fwver > 52) {
ret = gsc_i2c_read(dev, GSC_SC_THERM_PROTECT, &reg, 1);
if (!ret) {
if (outreg)
*outreg = reg;
if (tmax) {
*tmax = ((reg & 0xf8) >> 3) * 2;
if (*tmax)
*tmax += 70;
else
*tmax = 120;
}
if (enable)
*enable = reg & 1;
}
} else {
ret = -ENODEV;
}
return ret;
}
static int gsc_thermal_get_temp(struct udevice *dev)
{
struct gsc_priv *priv = dev_get_priv(dev);
u32 reg, mode, val;
const char *label;
ofnode node;
u8 buf[2];
ofnode_for_each_subnode(node, dev_read_subnode(dev, "adc")) {
if (ofnode_read_u32(node, "reg", &reg))
reg = -1;
if (ofnode_read_u32(node, "gw,mode", &mode))
mode = -1;
label = ofnode_read_string(node, "label");
if ((reg == -1) || (mode == -1) || !label)
continue;
if (mode != 0 || strcmp(label, "temp"))
continue;
memset(buf, 0, sizeof(buf));
if (!gsc_i2c_read(priv->hwmon, reg, buf, sizeof(buf))) {
val = buf[0] | buf[1] << 8;
if (val > 0x8000)
val -= 0xffff;
return val;
}
}
return 0;
}
static void gsc_thermal_info(struct udevice *dev)
{
struct gsc_priv *priv = dev_get_priv(dev);
switch (priv->gscver) {
case 2:
printf("board_temp:%dC ", gsc_thermal_get_temp(dev) / 10);
break;
case 3:
if (priv->fwver > 52) {
bool enabled;
int tmax;
if (!gsc_thermal_get_info(dev, NULL, &tmax, &enabled)) {
puts("Thermal protection:");
if (enabled)
printf("enabled at %dC ", tmax);
else
puts("disabled ");
}
}
break;
}
}
static void gsc_reset_info(struct udevice *dev)
{
struct gsc_priv *priv = dev_get_priv(dev);
static const char * const names[] = {
"VIN",
"PB",
"WDT",
"CPU",
"TEMP_L",
"TEMP_R",
"SLEEP",
"BOOT_WDT1",
"BOOT_WDT2",
"SOFT_PWR",
};
u8 reg;
/* reset cause */
switch (priv->gscver) {
case 2:
if (!gsc_i2c_read(dev, GSC_SC_STATUS, &reg, 1)) {
if (reg & BIT(GSC_SC_IRQ_WATCHDOG)) {
puts("RST:WDT");
reg &= ~BIT(GSC_SC_IRQ_WATCHDOG);
gsc_i2c_write(dev, GSC_SC_STATUS, &reg, 1);
} else {
puts("RST:VIN");
}
printf(" WDT:%sabled ",
(reg & BIT(GSC_SC_CTRL1_WDEN)) ? "en" : "dis");
}
break;
case 3:
if (priv->fwver > 52 &&
!gsc_i2c_read(dev, GSC_SC_RST_CAUSE, &reg, 1)) {
puts("RST:");
if (reg < ARRAY_SIZE(names))
printf("%s ", names[reg]);
else
printf("0x%02x ", reg);
}
break;
}
}
/* display hardware monitor ADC channels */
static int gsc_hwmon(struct udevice *dev)
{
struct gsc_priv *priv = dev_get_priv(dev);
u32 reg, mode, val, offset;
const char *label;
ofnode node;
u8 buf[2];
u32 r[2];
int ret;
/* iterate over hwmon nodes */
ofnode_for_each_subnode(node, dev_read_subnode(dev, "adc")) {
if (ofnode_read_u32(node, "reg", &reg))
reg = -1;
if (ofnode_read_u32(node, "gw,mode", &mode))
mode = -1;
label = ofnode_read_string(node, "label");
if ((reg == -1) || (mode == -1) || !label)
continue;
memset(buf, 0, sizeof(buf));
ret = gsc_i2c_read(priv->hwmon, reg, buf, sizeof(buf));
if (ret) {
printf("i2c error: %d\n", ret);
continue;
}
val = buf[0] | buf[1] << 8;
switch (mode) {
case 0: /* temperature (C*10) */
if (val > 0x8000)
val -= 0xffff;
printf("%-8s: %d.%ldC\n", label, val / 10, abs(val % 10));
break;
case 1: /* prescaled voltage */
if (val != 0xffff)
printf("%-8s: %d.%03dV\n", label, val / 1000, val % 1000);
break;
case 2: /* scaled based on ref volt and resolution */
val *= 2500;
val /= 1 << 12;
/* apply pre-scaler voltage divider */
if (!ofnode_read_u32_index(node, "gw,voltage-divider-ohms", 0, &r[0]) &&
!ofnode_read_u32_index(node, "gw,voltage-divider-ohms", 1, &r[1]) &&
r[0] && r[1]) {
val *= (r[0] + r[1]);
val /= r[1];
}
/* adjust by offset */
val += (offset / 1000);
printf("%-8s: %d.%03dV\n", label, val / 1000, val % 1000);
break;
}
}
return 0;
}
static int gsc_banner(struct udevice *dev)
{
struct gsc_priv *priv = dev_get_priv(dev);
/* banner */
printf("GSCv%d : v%d 0x%04x ", priv->gscver, priv->fwver, priv->fwcrc);
gsc_reset_info(dev);
gsc_thermal_info(dev);
puts("\n");
/* Display RTC */
if (priv->rtc) {
u8 buf[4];
time_t timestamp;
struct rtc_time tm;
if (!gsc_i2c_read(priv->rtc, 0, buf, 4)) {
timestamp = get_unaligned_le32(buf);
rtc_to_tm(timestamp, &tm);
printf("RTC : %4d-%02d-%02d %2d:%02d:%02d UTC\n",
tm.tm_year, tm.tm_mon, tm.tm_mday,
tm.tm_hour, tm.tm_min, tm.tm_sec);
}
}
return 0;
}
static int gsc_probe(struct udevice *dev)
{
struct gsc_priv *priv = dev_get_priv(dev);
u8 buf[32];
int ret;
ret = gsc_i2c_read(dev, 0, buf, sizeof(buf));
if (ret)
return ret;
/*
* GSC chip version:
* GSCv2 has 16 registers (which overlap)
* GSCv3 has 32 registers
*/
priv->gscver = memcmp(buf, buf + 16, 16) ? 3 : 2;
priv->fwver = buf[GSC_SC_FWVER];
priv->fwcrc = buf[GSC_SC_FWCRC] | buf[GSC_SC_FWCRC + 1] << 8;
priv->hwmon = gsc_get_dev(GSC_BUSNO, GSC_HWMON_ADDR);
if (priv->hwmon)
dev_set_priv(priv->hwmon, priv);
priv->rtc = gsc_get_dev(GSC_BUSNO, GSC_RTC_ADDR);
if (priv->rtc)
dev_set_priv(priv->rtc, priv);
#ifdef CONFIG_SPL_BUILD
gsc_banner(dev);
#endif
return 0;
};
static const struct udevice_id gsc_ids[] = {
{ .compatible = "gw,gsc", },
{ }
};
U_BOOT_DRIVER(gsc) = {
.name = "gsc",
.id = UCLASS_MISC,
.of_match = gsc_ids,
.probe = gsc_probe,
.priv_auto = sizeof(struct gsc_priv),
.flags = DM_FLAG_PRE_RELOC,
};
static int gsc_sleep(struct udevice *dev, unsigned long secs)
{
u8 regs[4];
int ret;
printf("GSC Sleeping for %ld seconds\n", secs);
put_unaligned_le32(secs, regs);
ret = gsc_i2c_write(dev, GSC_SC_TIME_ADD, regs, sizeof(regs));
if (ret)
goto err;
ret = gsc_i2c_read(dev, GSC_SC_CTRL1, regs, 1);
if (ret)
goto err;
regs[0] |= BIT(GSC_SC_CTRL1_SLEEP_ADD);
ret = gsc_i2c_write(dev, GSC_SC_CTRL1, regs, 1);
if (ret)
goto err;
regs[0] &= ~BIT(GSC_SC_CTRL1_SLEEP_ADD);
regs[0] |= BIT(GSC_SC_CTRL1_SLEEP_EN) | BIT(GSC_SC_CTRL1_SLEEP_ACTIVATE);
ret = gsc_i2c_write(dev, GSC_SC_CTRL1, regs, 1);
if (ret)
goto err;
return 0;
err:
printf("i2c error: %d\n", ret);
return ret;
}
static int gsc_wd_disable(struct udevice *dev)
{
int ret;
u8 reg;
ret = gsc_i2c_read(dev, GSC_SC_CTRL1, &reg, 1);
if (ret)
goto err;
reg |= BIT(GSC_SC_CTRL1_WDDIS);
reg &= ~BIT(GSC_SC_CTRL1_BOOT_CHK);
ret = gsc_i2c_write(dev, GSC_SC_CTRL1, &reg, 1);
if (ret)
goto err;
puts("GSC : boot watchdog disabled\n");
return 0;
err:
puts("i2c error");
return ret;
}
static int gsc_thermal(struct udevice *dev, const char *cmd, const char *val)
{
struct gsc_priv *priv = dev_get_priv(dev);
int ret, tmax;
bool enabled;
u8 reg;
if (priv->gscver < 3 || priv->fwver < 53)
return -EINVAL;
ret = gsc_thermal_get_info(dev, &reg, &tmax, &enabled);
if (ret)
return ret;
if (cmd && !strcmp(cmd, "enable")) {
if (val && *val) {
tmax = clamp((int)simple_strtoul(val, NULL, 0), 72, 122);
reg &= ~0xf8;
reg |= ((tmax - 70) / 2) << 3;
}
reg |= BIT(0);
gsc_i2c_write(dev, GSC_SC_THERM_PROTECT, &reg, 1);
} else if (cmd && !strcmp(cmd, "disable")) {
reg &= ~BIT(0);
gsc_i2c_write(dev, GSC_SC_THERM_PROTECT, &reg, 1);
} else if (cmd) {
return -EINVAL;
}
/* show status */
gsc_thermal_info(dev);
puts("\n");
return 0;
}
/* override in board files to display additional board EEPROM info */
__weak void board_gsc_info(void)
{
}
static void gsc_info(struct udevice *dev)
{
gsc_banner(dev);
board_gsc_info();
}
static int do_gsc(struct cmd_tbl *cmdtp, int flag, int argc, char * const argv[])
{
struct udevice *dev;
int ret;
/* get/probe driver */
ret = uclass_get_device_by_driver(UCLASS_MISC, DM_DRIVER_GET(gsc), &dev);
if (ret)
return CMD_RET_USAGE;
if (argc < 2) {
gsc_info(dev);
return CMD_RET_SUCCESS;
} else if (strcasecmp(argv[1], "sleep") == 0) {
if (argc < 3)
return CMD_RET_USAGE;
if (!gsc_sleep(dev, dectoul(argv[2], NULL)))
return CMD_RET_SUCCESS;
} else if (strcasecmp(argv[1], "hwmon") == 0) {
if (!gsc_hwmon(dev))
return CMD_RET_SUCCESS;
} else if (strcasecmp(argv[1], "wd-disable") == 0) {
if (!gsc_wd_disable(dev))
return CMD_RET_SUCCESS;
} else if (strcasecmp(argv[1], "thermal") == 0) {
char *cmd, *val;
cmd = (argc > 2) ? argv[2] : NULL;
val = (argc > 3) ? argv[3] : NULL;
if (!gsc_thermal(dev, cmd, val))
return CMD_RET_SUCCESS;
}
return CMD_RET_USAGE;
}
U_BOOT_CMD(gsc, 4, 1, do_gsc, "Gateworks System Controller",
"[sleep <secs>]|[hwmon]|[wd-disable][thermal [disable|enable [temp]]]\n");
/* disable boot watchdog - useful for an SPL that wants to use falcon mode */
int gsc_boot_wd_disable(void)
{
struct udevice *dev;
int ret;
/* get/probe driver */
ret = uclass_get_device_by_driver(UCLASS_MISC, DM_DRIVER_GET(gsc), &dev);
if (!ret)
ret = gsc_wd_disable(dev);
return ret;
}
# else
/*
* GSCv2 will fail to ACK an I2C transaction if it is busy, which can occur
* during its 1HZ timer tick while reading ADC's. When this does occur,
* it will never be busy longer than 2 back-to-back transfers so retry 3 times.
*/
static int gsc_i2c_read(uint chip, uint addr, u8 *buf, int len)
{
int retry = 3;
int n = 0;
int ret;
while (n++ < retry) {
ret = i2c_read(chip, addr, 1, buf, len);
if (!ret)
break;
if (ret != -EREMOTEIO)
break;
printf("%s 0x%02x retry %d\n", __func__, addr, n);
mdelay(10);
}
return ret;
}
static int gsc_i2c_write(uint chip, uint addr, u8 *buf, int len)
{
int retry = 3;
int n = 0;
int ret;
while (n++ < retry) {
ret = i2c_write(chip, addr, 1, buf, len);
if (!ret)
break;
if (ret != -EREMOTEIO)
break;
printf("%s 0x%02x retry %d\n", __func__, addr, n);
mdelay(10);
}
return ret;
}
/* disable boot watchdog - useful for an SPL that wants to use falcon mode */
int gsc_boot_wd_disable(void)
{
u8 buf[32];
int ret;
i2c_set_bus_num(GSC_BUSNO);
ret = gsc_i2c_read(GSC_SC_ADDR, 0, buf, sizeof(buf));
if (!ret) {
buf[GSC_SC_CTRL1] |= BIT(GSC_SC_CTRL1_WDDIS);
ret = gsc_i2c_write(GSC_SC_ADDR, GSC_SC_CTRL1, &buf[GSC_SC_CTRL1], 1);
printf("GSCv%d: v%d 0x%04x ",
memcmp(buf, buf + 16, 16) ? 3 : 2,
buf[GSC_SC_FWVER],
buf[GSC_SC_FWCRC] | buf[GSC_SC_FWCRC + 1] << 8);
if (buf[GSC_SC_STATUS] & BIT(GSC_SC_IRQ_WATCHDOG)) {
puts("RST:WDT ");
buf[GSC_SC_STATUS] &= ~BIT(GSC_SC_IRQ_WATCHDOG);
gsc_i2c_write(GSC_SC_ADDR, GSC_SC_STATUS, &buf[GSC_SC_STATUS], 1);
} else {
puts("RST:VIN ");
}
puts("WDT:disabled\n");
}
return ret;
}
#endif

21
include/gsc.h Normal file
View File

@ -0,0 +1,21 @@
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2022 Gateworks Corporation
*/
#ifndef _GSC_H_
#define _GSC_H_
/*
* board_gsc_info - Display additional board info
*/
void board_gsc_info(void);
/*
* gsc_boot_wd_disable - disable the BOOT watchdog
*
* Return: 0 on success or negative error on failure
*/
int gsc_boot_wd_disable(void);
#endif