imx: imx8qxp: imx8qxp_mek switch to binman

Switch to use binman pack images

Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>

arch/arm/dts/fsl-imx8qxp-mek-u-boot.dtsi

@@ -3,6 +3,8 @@
  * Copyright 2018, 2021 NXP
  */
 
+#include "imx8qxp-u-boot.dtsi"
+
 &{/imx8qx-pm} {
 
 	u-boot,dm-spl;

arch/arm/dts/imx8qxp-u-boot.dtsi

@@ -0,0 +1,133 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2018, 2021 NXP
+ */
+
+/ {
+	binman: binman {
+		multiple-images;
+	};
+};
+
+&binman {
+#ifdef CONFIG_SPL
+	u-boot-spl-ddr {
+		align = <4>;
+		align-size = <4>;
+		filename = "u-boot-spl-ddr.bin";
+		pad-byte = <0xff>;
+
+		u-boot-spl {
+			align-end = <4>;
+			filename = "u-boot-spl.bin";
+		};
+	};
+
+	spl {
+		filename = "spl.bin";
+
+		mkimage {
+			args = "-n spl/u-boot-spl.cfgout -T imx8image -e 0x100000";
+
+			blob {
+				filename = "u-boot-spl-ddr.bin";
+			};
+		};
+	};
+#endif
+
+	itb {
+		filename = "u-boot.itb";
+
+		fit {
+			description = "Configuration to load ATF before U-Boot";
+			fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
+			fit,fdt-list = "of-list";
+			#address-cells = <1>;
+
+			images {
+				uboot {
+					arch = "arm64";
+					compression = "none";
+					description = "U-Boot (64-bit)";
+					load = <CONFIG_SYS_TEXT_BASE>;
+					type = "standalone";
+
+					uboot-blob {
+						filename = "u-boot-nodtb.bin";
+						type = "blob-ext";
+					};
+				};
+
+				atf {
+					arch = "arm64";
+					compression = "none";
+					description = "ARM Trusted Firmware";
+					entry = <0x00910000>;
+					load =  <0x00091000>;
+					type = "firmware";
+
+					atf-blob {
+						filename = "bl31.bin";
+						type = "atf-bl31";
+					};
+				};
+
+				scfw {
+					arch = "arm64";
+					compression = "none";
+					description = "System Controler Firmware";
+					type = "firmware";
+
+					scfw_blob {
+						filename = "mx8qx-mek-scfw-tcm.bin";
+						type = "blob-ext";
+					};
+				};
+
+				seco {
+					arch = "arm64";
+					compression = "none";
+					description = "Seco Firmware";
+					type = "firmware";
+
+					seco_blob {
+						filename = "mx8qxc0-ahab-container.img";
+						type = "blob-ext";
+					};
+				};
+
+				fdt {
+					type = "flat_dt";
+					compression = "none";
+
+					uboot-fdt-blob {
+						filename = "u-boot.dtb";
+						type = "blob-ext";
+					};
+				};
+			};
+
+			configurations {
+				default = "conf";
+
+				conf {
+					fdt = "fdt";
+					firmware = "uboot";
+					loadables = "atf";
+				};
+			};
+		};
+	};
+
+	imx-boot {
+		filename = "flash.bin";
+		pad-byte = <0x00>;
+
+		spl {
+			filename = "spl.bin";
+			offset = <0x0>;
+			type = "blob-ext";
+		};
+	};
+};

arch/arm/mach-imx/imx8/Kconfig

@@ -90,6 +90,7 @@ config TARGET_IMX8QM_ROM7720_A1
 
 config TARGET_IMX8QXP_MEK
 	bool "Support i.MX8QXP MEK board"
+	select BINMAN
 	select BOARD_LATE_INIT
 	select IMX8QXP
 	select FSL_CAAM

board/freescale/imx8qxp_mek/imximage.cfg

@@ -7,8 +7,7 @@
  */
 
 
-/* Boot from SD, sector size 0x400 */
-BOOT_FROM SD 0x400
+BOOT_FROM	sd
 /* SoC type IMX8QX */
 SOC_TYPE IMX8QX
 /* Append seco container image */

configs/imx8qxp_mek_defconfig

@@ -23,6 +23,8 @@ CONFIG_SYS_LOAD_ADDR=0x80280000
 CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
 CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80200000
 CONFIG_REMAKE_ELF=y
+CONFIG_FIT=y
+CONFIG_FIT_EXTERNAL_OFFSET=0x3000
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_OF_SYSTEM_SETUP=y
 CONFIG_BOOTDELAY=3

doc/board/nxp/imx8qxp_mek.rst

@@ -50,7 +50,7 @@ Build U-Boot
 .. code-block:: bash
 
   $ make imx8qxp_mek_defconfig
-  $ make flash.bin
+  $ make
 
 Flash the binary into the SD card
 ---------------------------------