rockchip: rk3328: add rock-pi-e dts file
The ROCK-PI-E is a credit card size SBC based on Rockchip RK3328
Quad-Core ARM Cortex A53.
Net - Dual ethernet port, 1 X Gbe, 1 X 100M
USB - USB 3.0
DC - USB-Type C, 5V 2A
Storage - TF card, eMMC
Just build idbloader.img and u-boot.itb for Rockpi E board and
follow the blow steps to replace the relevant partition.
dd if=idbloader.img of=/dev/sdcard seek=64 conv=notrunc
dd if=u-boot.itb of=/dev/sdcard seek=16384 conv=notrunc
Signed-off-by: Banglang Huang <banglang.huang@foxmail.com>
This commit is contained in:
b.l.huang
Kever Yang
parent
f85cb3d978
commit
5764911e67
@ -107,7 +107,8 @@ dtb-$(CONFIG_ROCKCHIP_RK3308) += \
|
||||
dtb-$(CONFIG_ROCKCHIP_RK3328) += \
|
||||
rk3328-evb.dtb \
|
||||
rk3328-roc-cc.dtb \
|
||||
rk3328-rock64.dtb
|
||||
rk3328-rock64.dtb \
|
||||
rk3328-rock-pi-e.dtb
|
||||
|
||||
dtb-$(CONFIG_ROCKCHIP_RK3368) += \
|
||||
rk3368-lion.dtb \
|
||||
|
||||
33
arch/arm/dts/rk3328-rock-pi-e-u-boot.dtsi
Normal file
33
arch/arm/dts/rk3328-rock-pi-e-u-boot.dtsi
Normal file
@ -0,0 +1,33 @@
|
||||
// SPDX-License-Identifier: GPL-2.0+
|
||||
/*
|
||||
* (C) Copyright 2020 Radxa
|
||||
*/
|
||||
|
||||
#include "rk3328-u-boot.dtsi"
|
||||
#include "rk3328-sdram-ddr3-666.dtsi"
|
||||
|
||||
&gpio0 {
|
||||
u-boot,dm-spl;
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
u-boot,dm-spl;
|
||||
};
|
||||
|
||||
&sdmmc0m1_gpio {
|
||||
u-boot,dm-spl;
|
||||
};
|
||||
|
||||
&pcfg_pull_up_4ma {
|
||||
u-boot,dm-spl;
|
||||
};
|
||||
|
||||
&usb_host0_xhci {
|
||||
vbus-supply = <&vcc5v0_host_xhci>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
/* Need this and all the pinctrl/gpio stuff above to set pinmux */
|
||||
&vcc_sd {
|
||||
u-boot,dm-spl;
|
||||
};
|
||||
267
arch/arm/dts/rk3328-rock-pi-e.dts
Normal file
267
arch/arm/dts/rk3328-rock-pi-e.dts
Normal file
@ -0,0 +1,267 @@
|
||||
// SPDX-License-Identifier: GPL-2.0+
|
||||
/*
|
||||
* (C) Copyright 2020 Radxa
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
#include "rk3328.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Radxa Rockpi E";
|
||||
compatible = "radxa,rock-pi-e", "rockchip,rk3328";
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial2:1500000n8";
|
||||
};
|
||||
|
||||
gmac_clkin: external-gmac-clock {
|
||||
compatible = "fixed-clock";
|
||||
clock-frequency = <125000000>;
|
||||
clock-output-names = "gmac_clkin";
|
||||
#clock-cells = <0>;
|
||||
};
|
||||
|
||||
vcc_sd: sdmmc-regulator {
|
||||
compatible = "regulator-fixed";
|
||||
gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&sdmmc0m1_gpio>;
|
||||
regulator-name = "vcc_sd";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
vin-supply = <&vcc_io>;
|
||||
};
|
||||
|
||||
vcc5v0_host_xhci: vcc5v0-host-xhci-drv {
|
||||
compatible = "regulator-fixed";
|
||||
enable-active-high;
|
||||
regulator-name = "vcc5v0_host_xhci";
|
||||
gpio = <&gpio3 RK_PA7 GPIO_ACTIVE_HIGH>;
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
};
|
||||
|
||||
vcc_sys: vcc-sys {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vcc_sys";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
};
|
||||
};
|
||||
|
||||
&cpu0 {
|
||||
cpu-supply = <&vdd_arm>;
|
||||
};
|
||||
|
||||
&cpu1 {
|
||||
cpu-supply = <&vdd_arm>;
|
||||
};
|
||||
|
||||
&cpu2 {
|
||||
cpu-supply = <&vdd_arm>;
|
||||
};
|
||||
|
||||
&cpu3 {
|
||||
cpu-supply = <&vdd_arm>;
|
||||
};
|
||||
|
||||
&emmc {
|
||||
bus-width = <8>;
|
||||
cap-mmc-highspeed;
|
||||
mmc-hs200-1_8v;
|
||||
supports-emmc;
|
||||
disable-wp;
|
||||
non-removable;
|
||||
num-slots = <1>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
|
||||
vmmc-supply = <&vcc_io>;
|
||||
vqmmc-supply = <&vcc18_emmc>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gmac2io {
|
||||
assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
|
||||
assigned-clock-parents = <&gmac_clkin>, <&gmac_clkin>;
|
||||
clock_in_out = "input";
|
||||
phy-supply = <&vcc_io>;
|
||||
phy-mode = "rgmii";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&rgmiim1_pins>;
|
||||
snps,force_thresh_dma_mode;
|
||||
snps,reset-gpio = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
|
||||
snps,reset-active-low;
|
||||
snps,reset-delays-us = <0 10000 50000>;
|
||||
tx_delay = <0x26>;
|
||||
rx_delay = <0x11>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c1 {
|
||||
status = "okay";
|
||||
|
||||
rk805: rk805@18 {
|
||||
compatible = "rockchip,rk805";
|
||||
status = "okay";
|
||||
reg = <0x18>;
|
||||
interrupt-parent = <&gpio2>;
|
||||
interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
|
||||
#clock-cells = <1>;
|
||||
clock-output-names = "xin32k", "rk805-clkout2";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pmic_int_l>;
|
||||
rockchip,system-power-controller;
|
||||
wakeup-source;
|
||||
|
||||
vcc1-supply = <&vcc_sys>;
|
||||
vcc2-supply = <&vcc_sys>;
|
||||
vcc3-supply = <&vcc_sys>;
|
||||
vcc4-supply = <&vcc_sys>;
|
||||
vcc5-supply = <&vcc_io>;
|
||||
vcc6-supply = <&vcc_sys>;
|
||||
|
||||
regulators {
|
||||
vdd_logic: DCDC_REG1 {
|
||||
regulator-name = "vdd_logic";
|
||||
regulator-min-microvolt = <712500>;
|
||||
regulator-max-microvolt = <1450000>;
|
||||
regulator-ramp-delay = <12500>;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-state-mem {
|
||||
regulator-on-in-suspend;
|
||||
regulator-suspend-microvolt = <1000000>;
|
||||
};
|
||||
};
|
||||
|
||||
vdd_arm: DCDC_REG2 {
|
||||
regulator-name = "vdd_arm";
|
||||
regulator-min-microvolt = <712500>;
|
||||
regulator-max-microvolt = <1450000>;
|
||||
regulator-ramp-delay = <12500>;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-state-mem {
|
||||
regulator-on-in-suspend;
|
||||
regulator-suspend-microvolt = <950000>;
|
||||
};
|
||||
};
|
||||
|
||||
vcc_ddr: DCDC_REG3 {
|
||||
regulator-name = "vcc_ddr";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-state-mem {
|
||||
regulator-on-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vcc_io: DCDC_REG4 {
|
||||
regulator-name = "vcc_io";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-state-mem {
|
||||
regulator-on-in-suspend;
|
||||
regulator-suspend-microvolt = <3300000>;
|
||||
};
|
||||
};
|
||||
|
||||
vcc_18: LDO_REG1 {
|
||||
regulator-name = "vcc_18";
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-state-mem {
|
||||
regulator-on-in-suspend;
|
||||
regulator-suspend-microvolt = <1800000>;
|
||||
};
|
||||
};
|
||||
|
||||
vcc18_emmc: LDO_REG2 {
|
||||
regulator-name = "vcc18_emmc";
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-state-mem {
|
||||
regulator-on-in-suspend;
|
||||
regulator-suspend-microvolt = <1800000>;
|
||||
};
|
||||
};
|
||||
|
||||
vdd_10: LDO_REG3 {
|
||||
regulator-name = "vdd_10";
|
||||
regulator-min-microvolt = <1000000>;
|
||||
regulator-max-microvolt = <1000000>;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-state-mem {
|
||||
regulator-on-in-suspend;
|
||||
regulator-suspend-microvolt = <1000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&io_domains {
|
||||
status = "okay";
|
||||
|
||||
vccio1-supply = <&vcc_io>;
|
||||
vccio2-supply = <&vcc18_emmc>;
|
||||
vccio3-supply = <&vcc_io>;
|
||||
vccio4-supply = <&vcc_io>;
|
||||
vccio5-supply = <&vcc_io>;
|
||||
vccio6-supply = <&vcc_io>;
|
||||
pmuio-supply = <&vcc_io>;
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
pmic {
|
||||
pmic_int_l: pmic-int-l {
|
||||
rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&sdmmc {
|
||||
bus-width = <4>;
|
||||
cap-mmc-highspeed;
|
||||
cap-sd-highspeed;
|
||||
card-detect-delay = <200>;
|
||||
disable-wp;
|
||||
max-frequency = <150000000>;
|
||||
num-slots = <1>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_dectn &sdmmc0_bus4>;
|
||||
supports-sd;
|
||||
vmmc-supply = <&vcc_sd>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&saradc {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart2 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb20_otg {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_host0_ehci {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_host0_ohci {
|
||||
status = "okay";
|
||||
};
|
||||
Loading…
Reference in New Issue
Block a user