ppc: Drop t4qds and b4860qds references
These boards have been removed. Drop the config file and other references. Signed-off-by: Simon Glass <sjg@chromium.org>
This commit is contained in:
Simon Glass
Tom Rini
parent
666671ecc3
commit
4a753fbcee
@ -413,11 +413,11 @@ jobs:
|
||||
non_fsl_ppc:
|
||||
BUILDMAN: "powerpc -x freescale"
|
||||
mpc85xx_freescale:
|
||||
BUILDMAN: "mpc85xx&freescale -x t208xrdb -x t4qds -x t102* -x p1_p2_rdb_pc -x p1010rdb -x corenet_ds -x b4860qds -x bsc91*"
|
||||
BUILDMAN: "mpc85xx&freescale -x t208xrdb -x t102* -x p1_p2_rdb_pc -x p1010rdb -x corenet_ds -x bsc91*"
|
||||
t208xrdb_corenet_ds:
|
||||
BUILDMAN: "t208xrdb corenet_ds"
|
||||
fsl_ppc:
|
||||
BUILDMAN: "t4qds b4860qds mpc83xx&freescale"
|
||||
BUILDMAN: "mpc83xx&freescale"
|
||||
t102x:
|
||||
BUILDMAN: "t102*"
|
||||
p1_p2_rdb_pc:
|
||||
|
||||
@ -1,453 +0,0 @@
|
||||
.. SPDX-License-Identifier: GPL-2.0+
|
||||
|
||||
B4860QDS
|
||||
========
|
||||
|
||||
The B4860QDS is a Freescale reference board that hosts the B4860 SoC
|
||||
(and variants).
|
||||
|
||||
B4860 Overview
|
||||
--------------
|
||||
The B4860 QorIQ Qonverge device is a Freescale high-end, multicore SoC based on
|
||||
StarCore and Power Architecture® cores. It targets the broadband wireless
|
||||
infrastructure and builds upon the proven success of the existing multicore
|
||||
DSPs and Power CPUs. It is designed to bolster the rapidly changing and
|
||||
expanding wireless markets, such as 3GLTE (FDD and TDD), LTE-Advanced, and UMTS.
|
||||
|
||||
The B4860 is a highly-integrated StarCore and Power Architecture processor that
|
||||
contains:
|
||||
|
||||
* Six fully-programmable StarCore SC3900 FVP subsystems, divided into three
|
||||
clusters-each core runs up to 1.2 GHz, with an architecture highly optimized
|
||||
for wireless base station applications
|
||||
* Four dual-thread e6500 Power Architecture processors organized in one
|
||||
cluster-each core runs up to 1.8 GHz
|
||||
* Two DDR3/3L controllers for high-speed, industry-standard memory interface
|
||||
each runs at up to 1866.67 MHz
|
||||
* MAPLE-B3 hardware acceleration-for forward error correction schemes including
|
||||
Turbo or Viterbi decoding, Turbo encoding and rate matching, MIMO MMSE
|
||||
equalization scheme, matrix operations, CRC insertion and check, DFT/iDFT and
|
||||
FFT/iFFT calculations, PUSCH/PDSCH acceleration, and UMTS chip rate
|
||||
acceleration
|
||||
* CoreNet fabric that fully supports coherency using MESI protocol between the
|
||||
e6500 cores, SC3900 FVP cores, memories and external interfaces.
|
||||
CoreNet fabric interconnect runs at 667 MHz and supports coherent and
|
||||
non-coherent out of order transactions with prioritization and bandwidth
|
||||
allocation amongst CoreNet endpoints.
|
||||
* Data Path Acceleration Architecture, which includes the following:
|
||||
|
||||
* Frame Manager (FMan), which supports in-line packet parsing and general
|
||||
classification to enable policing and QoS-based packet distribution
|
||||
* Queue Manager (QMan) and Buffer Manager (BMan), which allow offloading
|
||||
of queue management, task management, load distribution, flow ordering,
|
||||
buffer management, and allocation tasks from the cores
|
||||
* Security engine (SEC 5.3)-crypto-acceleration for protocols such as
|
||||
IPsec, SSL, and 802.16
|
||||
* RapidIO manager (RMAN) - Support SRIO types 8, 9, 10, and 11 (inbound
|
||||
and outbound). Supports types 5, 6 (outbound only)
|
||||
|
||||
* Large internal cache memory with snooping and stashing capabilities for
|
||||
bandwidth saving and high utilization of processor elements. The 9856-Kbyte
|
||||
internal memory space includes the following:
|
||||
|
||||
* 32 Kbyte L1 ICache per e6500/SC3900 core
|
||||
* 32 Kbyte L1 DCache per e6500/SC3900 core
|
||||
* 2048 Kbyte unified L2 cache for each SC3900 FVP cluster
|
||||
* 2048 Kbyte unified L2 cache for the e6500 cluster
|
||||
* Two 512 Kbyte shared L3 CoreNet platform caches (CPC)
|
||||
|
||||
* Sixteen 10-GHz SerDes lanes serving:
|
||||
|
||||
* Two Serial RapidIO interfaces
|
||||
* Each supports up to 4 lanes and a total of up to 8 lanes
|
||||
|
||||
* Up to 8-lanes Common Public Radio Interface (CPRI) controller for
|
||||
glue-less antenna connection
|
||||
* Two 10-Gbit Ethernet controllers (10GEC)
|
||||
* Six 1G/2.5-Gbit Ethernet controllers for network communications
|
||||
* PCI Express controller
|
||||
* Debug (Aurora)
|
||||
* Two OCeaN DMAs
|
||||
* Various system peripherals
|
||||
* 182 32-bit timers
|
||||
|
||||
B4860QDS Overview
|
||||
-----------------
|
||||
- DDRC1: Ten separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s,
|
||||
ECC, 4 GB of memory in two ranks of 2 GB.
|
||||
- DDRC2: Five separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s,
|
||||
ECC, 2 GB of memory. Single rank.
|
||||
- SerDes 1 multiplexing: Two Vitesse (transmit and receive path) cross-point
|
||||
16x16 switch VSC3316
|
||||
- SerDes 2 multiplexing: Two Vitesse (transmit and receive path) cross-point
|
||||
8x8 switch VSC3308
|
||||
- USB 2.0 ULPI PHY USB3315 by SMSC supports USB port in host mode.
|
||||
B4860 UART port is available over USB-to-UART translator USB2SER or over
|
||||
RS232 flat cable.
|
||||
- A Vitesse dual SGMII phy VSC8662 links the B4860 SGMII lines to 2xRJ-45
|
||||
copper connectors for Stand-alone mode and to the 1000Base-X over AMC
|
||||
MicroTCA connector ports 0 and 2 for AMC mode.
|
||||
- The B4860 configuration may be loaded from nine bits coded reset configuration
|
||||
reset source. The RCW source is set by appropriate DIP-switches.
|
||||
- 16-bit NOR Flash / PROMJet
|
||||
- QIXIS 8-bit NOR Flash Emulator
|
||||
- 8-bit NAND Flash
|
||||
- 24-bit SPI Flash
|
||||
- Long address I2C EEPROM
|
||||
- Available debug interfaces are:
|
||||
|
||||
- On-board eCWTAP controller with ETH and USB I/F
|
||||
- JTAG/COP 16-pin header for any external TAP controller
|
||||
- External JTAG source over AMC to support B2B configuration
|
||||
- 70-pin Aurora debug connector
|
||||
|
||||
- QIXIS (FPGA) logic:
|
||||
- 2 KB internal memory space including
|
||||
|
||||
- IDT840NT4 clock synthesizer provides B4860 essential clocks : SYSCLK,
|
||||
DDRCLK1,2 and RTCCLK.
|
||||
- Two 8T49N222A SerDes ref clock devices support two SerDes port clock
|
||||
frequency - total four refclk, including CPRI clock scheme.
|
||||
|
||||
|
||||
B4420 Personality
|
||||
-----------------
|
||||
|
||||
B4420 is a reduced personality of B4860 with less core/clusters(both SC3900
|
||||
and e6500), less DDR controllers, less serdes lanes, less SGMII interfaces
|
||||
and reduced target frequencies.
|
||||
|
||||
Key differences between B4860 and B4420
|
||||
---------------------------------------
|
||||
|
||||
B4420 has:
|
||||
|
||||
1. Less e6500 cores: 1 cluster with 2 e6500 cores
|
||||
2. Less SC3900 cores/clusters: 1 cluster with 2 SC3900 cores per cluster
|
||||
3. Single DDRC
|
||||
4. 2X 4 lane serdes
|
||||
5. 3 SGMII interfaces
|
||||
6. no sRIO
|
||||
7. no 10G
|
||||
|
||||
B4860QDS Default Settings
|
||||
-------------------------
|
||||
|
||||
Switch Settings
|
||||
^^^^^^^^^^^^^^^
|
||||
|
||||
.. code-block:: none
|
||||
|
||||
SW1 OFF [0] OFF [0] OFF [0] OFF [0] OFF [0] OFF [0] OFF [0] OFF [0]
|
||||
SW2 ON ON ON ON ON ON OFF OFF
|
||||
SW3 OFF OFF OFF ON OFF OFF ON OFF
|
||||
SW5 OFF OFF OFF OFF OFF OFF ON ON
|
||||
|
||||
Note:
|
||||
|
||||
- PCIe slots modes: All the PCIe devices work as Root Complex.
|
||||
- Boot location: NOR flash.
|
||||
|
||||
SysClk/Core(e6500)/CCB/DDR/FMan/DDRCLK/StarCore/CPRI-Maple/eTVPE-Maple/ULB-Maple
|
||||
66MHz/1.6GHz/667MHz/1.6GHz data rate/667MHz/133MHz/1200MHz/500MHz/800MHz/667MHz
|
||||
|
||||
NAND boot::
|
||||
|
||||
SW1 [1.1] = 0
|
||||
SW2 [1.1] = 1
|
||||
SW3 [1:4] = 0001
|
||||
|
||||
NOR boot::
|
||||
|
||||
SW1 [1.1] = 1
|
||||
SW2 [1.1] = 0
|
||||
SW3 [1:4] = 1000
|
||||
|
||||
B4420QDS Default Settings
|
||||
-------------------------
|
||||
|
||||
Switch Settings
|
||||
^^^^^^^^^^^^^^^
|
||||
|
||||
.. code-block:: none
|
||||
|
||||
SW1 OFF[0] OFF [0] OFF [0] OFF [0] OFF [0] OFF [0] OFF [0] OFF [0]
|
||||
SW2 ON OFF ON OFF ON ON OFF OFF
|
||||
SW3 OFF OFF OFF ON OFF OFF ON OFF
|
||||
SW5 OFF OFF OFF OFF OFF OFF ON ON
|
||||
|
||||
Note:
|
||||
|
||||
- PCIe slots modes: All the PCIe devices work as Root Complex.
|
||||
- Boot location: NOR flash.
|
||||
|
||||
SysClk/Core(e6500)/CCB/DDR/FMan/DDRCLK/StarCore/CPRI-Maple/eTVPE-Maple/ULB-Maple
|
||||
66MHz/1.6GHz/667MHz/1.6GHz data rate/667MHz/133MHz/1200MHz/500MHz/800MHz/667MHz
|
||||
|
||||
NAND boot::
|
||||
|
||||
SW1 [1.1] = 0
|
||||
SW2 [1.1] = 1
|
||||
SW3 [1:4] = 0001
|
||||
|
||||
NOR boot::
|
||||
|
||||
SW1 [1.1] = 1
|
||||
SW2 [1.1] = 0
|
||||
SW3 [1:4] = 1000
|
||||
|
||||
Memory map on B4860QDS
|
||||
----------------------
|
||||
The addresses in brackets are physical addresses.
|
||||
|
||||
============= ============= =============== =======
|
||||
Start Address End Address Description Size
|
||||
============= ============= =============== =======
|
||||
0xF_FFDF_1000 0xF_FFFF_FFFF Free 2 MB
|
||||
0xF_FFDF_0000 0xF_FFDF_0FFF IFC - FPGA 4 KB
|
||||
0xF_FF81_0000 0xF_FFDE_FFFF Free 5 MB
|
||||
0xF_FF80_0000 0xF_FF80_FFFF IFC NAND Flash 64 KB
|
||||
0xF_FF00_0000 0xF_FF7F_FFFF Free 8 MB
|
||||
0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16 MB
|
||||
0xF_F801_0000 0xF_FDFF_FFFF Free 95 MB
|
||||
0xF_F800_0000 0xF_F800_FFFF PCIe I/O Space 64 KB
|
||||
0xF_F600_0000 0xF_F7FF_FFFF QMAN s/w portal 32 MB
|
||||
0xF_F400_0000 0xF_F5FF_FFFF BMAN s/w portal 32 MB
|
||||
0xF_F000_0000 0xF_F3FF_FFFF Free 64 MB
|
||||
0xF_E800_0000 0xF_EFFF_FFFF IFC NOR Flash 128 MB
|
||||
0xF_E000_0000 0xF_E7FF_FFFF Promjet 128 MB
|
||||
0xF_A0C0_0000 0xF_DFFF_FFFF Free 1012 MB
|
||||
0xF_A000_0000 0xF_A0BF_FFFF MAPLE0/1/2 12 MB
|
||||
0xF_0040_0000 0xF_9FFF_FFFF Free 12 GB
|
||||
0xF_0000_0000 0xF_01FF_FFFF DCSR 32 MB
|
||||
0xC_4000_0000 0xE_FFFF_FFFF Free 11 GB
|
||||
0xC_3000_0000 0xC_3FFF_FFFF sRIO-2 I/O 256 MB
|
||||
0xC_2000_0000 0xC_2FFF_FFFF sRIO-1 I/O 256 MB
|
||||
0xC_0000_0000 0xC_1FFF_FFFF PCIe Mem Space 512 MB
|
||||
0x1_0000_0000 0xB_FFFF_FFFF Free 44 GB
|
||||
0x0_8000_0000 0x0_FFFF_FFFF DDRC1 2 GB
|
||||
0x0_0000_0000 0x0_7FFF_FFFF DDRC2 2 GB
|
||||
============= ============= =============== =======
|
||||
|
||||
Memory map on B4420QDS
|
||||
----------------------
|
||||
The addresses in brackets are physical addresses.
|
||||
|
||||
============= ============= =============== =======
|
||||
Start Address End Address Description Size
|
||||
============= ============= =============== =======
|
||||
0xF_FFDF_1000 0xF_FFFF_FFFF Free 2 MB
|
||||
0xF_FFDF_0000 0xF_FFDF_0FFF IFC - FPGA 4 KB
|
||||
0xF_FF81_0000 0xF_FFDE_FFFF Free 5 MB
|
||||
0xF_FF80_0000 0xF_FF80_FFFF IFC NAND Flash 64 KB
|
||||
0xF_FF00_0000 0xF_FF7F_FFFF Free 8 MB
|
||||
0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16 MB
|
||||
0xF_F801_0000 0xF_FDFF_FFFF Free 95 MB
|
||||
0xF_F800_0000 0xF_F800_FFFF PCIe I/O Space 64 KB
|
||||
0xF_F600_0000 0xF_F7FF_FFFF QMAN s/w portal 32 MB
|
||||
0xF_F400_0000 0xF_F5FF_FFFF BMAN s/w portal 32 MB
|
||||
0xF_F000_0000 0xF_F3FF_FFFF Free 64 MB
|
||||
0xF_E800_0000 0xF_EFFF_FFFF IFC NOR Flash 128 MB
|
||||
0xF_E000_0000 0xF_E7FF_FFFF Promjet 128 MB
|
||||
0xF_A0C0_0000 0xF_DFFF_FFFF Free 1012 MB
|
||||
0xF_A000_0000 0xF_A0BF_FFFF MAPLE0/1/2 12 MB
|
||||
0xF_0040_0000 0xF_9FFF_FFFF Free 12 GB
|
||||
0xF_0000_0000 0xF_01FF_FFFF DCSR 32 MB
|
||||
0xC_4000_0000 0xE_FFFF_FFFF Free 11 GB
|
||||
0xC_3000_0000 0xC_3FFF_FFFF sRIO-2 I/O 256 MB
|
||||
0xC_2000_0000 0xC_2FFF_FFFF sRIO-1 I/O 256 MB
|
||||
0xC_0000_0000 0xC_1FFF_FFFF PCIe Mem Space 512 MB
|
||||
0x1_0000_0000 0xB_FFFF_FFFF Free 44 GB
|
||||
0x0_0000_0000 0x0_FFFF_FFFF DDRC1 4 GB
|
||||
============= ============= =============== =======
|
||||
|
||||
NOR Flash memory Map on B4860 and B4420QDS
|
||||
------------------------------------------
|
||||
|
||||
============= ============= ============================== =========
|
||||
Start End Definition Size
|
||||
============= ============= ============================== =========
|
||||
0xEFF40000 0xEFFFFFFF U-Boot (current bank) 768KB
|
||||
0xEFF20000 0xEFF3FFFF U-Boot env (current bank) 128KB
|
||||
0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB
|
||||
0xEF300000 0xEFEFFFFF rootfs (alternate bank) 12MB
|
||||
0xEE800000 0xEE8FFFFF device tree (alternate bank) 1MB
|
||||
0xEE020000 0xEE6FFFFF Linux.uImage (alternate bank) 6MB+896KB
|
||||
0xEE000000 0xEE01FFFF RCW (alternate bank) 128KB
|
||||
0xEDF40000 0xEDFFFFFF U-Boot (alternate bank) 768KB
|
||||
0xEDF20000 0xEDF3FFFF U-Boot env (alternate bank) 128KB
|
||||
0xEDF00000 0xEDF1FFFF FMAN ucode (alternate bank) 128KB
|
||||
0xED300000 0xEDEFFFFF rootfs (current bank) 12MB
|
||||
0xEC800000 0xEC8FFFFF device tree (current bank) 1MB
|
||||
0xEC020000 0xEC6FFFFF Linux.uImage (current bank) 6MB+896KB
|
||||
0xEC000000 0xEC01FFFF RCW (current bank) 128KB
|
||||
============= ============= ============================== =========
|
||||
|
||||
Various Software configurations/environment variables/commands
|
||||
--------------------------------------------------------------
|
||||
The below commands apply to both B4860QDS and B4420QDS.
|
||||
|
||||
U-Boot environment variable hwconfig
|
||||
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
||||
|
||||
The default hwconfig is:
|
||||
|
||||
.. code-block:: none
|
||||
|
||||
hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=cs0_cs1;usb1:dr_mode=host,phy_type=ulpi
|
||||
|
||||
Note: For USB gadget set "dr_mode=peripheral"
|
||||
|
||||
FMAN Ucode versions
|
||||
^^^^^^^^^^^^^^^^^^^
|
||||
|
||||
fsl_fman_ucode_B4860_106_3_6.bin
|
||||
|
||||
Switching to alternate bank
|
||||
^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
||||
|
||||
Commands for switching to alternate bank.
|
||||
|
||||
1. To change from vbank0 to vbank2
|
||||
|
||||
.. code-block:: none
|
||||
|
||||
=> qixis_reset altbank (it will boot using vbank2)
|
||||
|
||||
2. To change from vbank2 to vbank0
|
||||
|
||||
.. code-block:: none
|
||||
|
||||
=> qixis reset (it will boot using vbank0)
|
||||
|
||||
To change personality of board
|
||||
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
||||
|
||||
For changing personality from B4860 to B4420
|
||||
|
||||
1. Boot from vbank0
|
||||
2. Flash vbank2 with b4420 rcw and U-Boot
|
||||
3. Give following commands to uboot prompt
|
||||
|
||||
.. code-block:: none
|
||||
|
||||
=> mw.b ffdf0040 0x30;
|
||||
=> mw.b ffdf0010 0x00;
|
||||
=> mw.b ffdf0062 0x02;
|
||||
=> mw.b ffdf0050 0x02;
|
||||
=> mw.b ffdf0010 0x30;
|
||||
=> reset
|
||||
|
||||
Note:
|
||||
|
||||
- Power off cycle will lead to default switch settings.
|
||||
- 0xffdf0000 is the address of the QIXIS FPGA.
|
||||
|
||||
Switching between NOR and NAND boot(RCW src changed from NOR <-> NAND)
|
||||
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
||||
|
||||
To change from NOR to NAND boot give following command on uboot prompt
|
||||
|
||||
.. code-block:: none
|
||||
|
||||
=> mw.b ffdf0040 0x30
|
||||
=> mw.b ffdf0010 0x00
|
||||
=> mw.b 0xffdf0050 0x08
|
||||
=> mw.b 0xffdf0060 0x82
|
||||
=> mw.b ffdf0061 0x00
|
||||
=> mw.b ffdf0010 0x30
|
||||
=> reset
|
||||
|
||||
To change from NAND to NOR boot give following command on uboot prompt:
|
||||
|
||||
.. code-block:: none
|
||||
|
||||
=> mw.b ffdf0040 0x30
|
||||
=> mw.b ffdf0010 0x00
|
||||
=> mw.b 0xffdf0050 0x00(for vbank0) or (mw.b 0xffdf0050 0x02 for vbank2)
|
||||
=> mw.b 0xffdf0060 0x12
|
||||
=> mw.b ffdf0061 0x01
|
||||
=> mw.b ffdf0010 0x30
|
||||
=> reset
|
||||
|
||||
Note:
|
||||
|
||||
- Power off cycle will lead to default switch settings.
|
||||
- 0xffdf0000 is the address of the QIXIS FPGA.
|
||||
|
||||
Ethernet interfaces for B4860QDS
|
||||
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
||||
|
||||
Serdes protocosl tested:
|
||||
* 0x2a, 0x8d (serdes1, serdes2) [DEFAULT]
|
||||
* 0x2a, 0xb2 (serdes1, serdes2)
|
||||
|
||||
When using [DEFAULT] RCW, which including 2 * 1G SGMII on board and 2 * 1G
|
||||
SGMII on SGMII riser card.
|
||||
|
||||
Under U-Boot these network interfaces are recognized as::
|
||||
|
||||
FM1@DTSEC3, FM1@DTSEC4, FM1@DTSEC5 and FM1@DTSEC6.
|
||||
|
||||
On Linux the interfaces are renamed as::
|
||||
|
||||
eth2 -> fm1-gb2
|
||||
eth3 -> fm1-gb3
|
||||
eth4 -> fm1-gb4
|
||||
eth5 -> fm1-gb5
|
||||
|
||||
RCW and Ethernet interfaces for B4420QDS
|
||||
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
||||
|
||||
Serdes protocosl tested:
|
||||
* 0x18, 0x9e (serdes1, serdes2)
|
||||
|
||||
Under U-Boot these network interfaces are recognized as::
|
||||
|
||||
FM1@DTSEC3, FM1@DTSEC4 and e1000#0.
|
||||
|
||||
On Linux the interfaces are renamed as::
|
||||
|
||||
eth2 -> fm1-gb2
|
||||
eth3 -> fm1-gb3
|
||||
|
||||
NAND boot with 2 Stage boot loader
|
||||
----------------------------------
|
||||
PBL initialise the internal SRAM and copy SPL(160KB) in SRAM.
|
||||
SPL further initialise DDR using SPD and environment variables and copy
|
||||
U-Boot(768 KB) from flash to DDR.
|
||||
Finally SPL transer control to U-Boot for futher booting.
|
||||
|
||||
SPL has following features:
|
||||
- Executes within 256K
|
||||
- No relocation required
|
||||
|
||||
Run time view of SPL framework during boot:
|
||||
|
||||
+----------------------------------------------+
|
||||
|Area | Address |
|
||||
+----------------------------------------------+
|
||||
|Secure boot | 0xFFFC0000 (32KB) |
|
||||
|headers | |
|
||||
+----------------------------------------------+
|
||||
|GD, BD | 0xFFFC8000 (4KB) |
|
||||
+----------------------------------------------+
|
||||
|ENV | 0xFFFC9000 (8KB) |
|
||||
+----------------------------------------------+
|
||||
|HEAP | 0xFFFCB000 (30KB) |
|
||||
+----------------------------------------------+
|
||||
|STACK | 0xFFFD8000 (22KB) |
|
||||
+----------------------------------------------+
|
||||
|U-Boot SPL | 0xFFFD8000 (160KB) |
|
||||
+----------------------------------------------+
|
||||
|
||||
NAND Flash memory Map on B4860 and B4420QDS
|
||||
-------------------------------------------
|
||||
|
||||
============= ============= ============================= =====
|
||||
Start End Definition Size
|
||||
============= ============= ============================= =====
|
||||
0x000000 0x0FFFFF U-Boot 1MB
|
||||
0x140000 0x15FFFF U-Boot env 128KB
|
||||
0x1A0000 0x1BFFFF FMAN Ucode 128KB
|
||||
============= ============= ============================= =====
|
||||
@ -6,7 +6,6 @@ Freescale
|
||||
.. toctree::
|
||||
:maxdepth: 2
|
||||
|
||||
b4860qds
|
||||
imx8mm_evk
|
||||
imx8mn_evk
|
||||
imx8mp_evk
|
||||
|
||||
@ -1,240 +0,0 @@
|
||||
/* SPDX-License-Identifier: GPL-2.0+ */
|
||||
/*
|
||||
* Copyright 2011-2012 Freescale Semiconductor, Inc.
|
||||
*/
|
||||
|
||||
/*
|
||||
* Corenet DS style board configuration file
|
||||
*/
|
||||
#ifndef __T4QDS_H
|
||||
#define __T4QDS_H
|
||||
|
||||
/* High Level Configuration Options */
|
||||
#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
|
||||
|
||||
#ifndef CONFIG_RESET_VECTOR_ADDRESS
|
||||
#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
|
||||
#endif
|
||||
|
||||
#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
|
||||
#define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS
|
||||
#define CONFIG_PCIE1 /* PCIE controller 1 */
|
||||
#define CONFIG_PCIE2 /* PCIE controller 2 */
|
||||
#define CONFIG_PCIE3 /* PCIE controller 3 */
|
||||
#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
|
||||
#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
|
||||
|
||||
#define CONFIG_SYS_SRIO
|
||||
#define CONFIG_SRIO1 /* SRIO port 1 */
|
||||
#define CONFIG_SRIO2 /* SRIO port 2 */
|
||||
|
||||
/*
|
||||
* These can be toggled for performance analysis, otherwise use default.
|
||||
*/
|
||||
#define CONFIG_SYS_CACHE_STASHING
|
||||
#define CONFIG_BTB /* toggle branch predition */
|
||||
#ifdef CONFIG_DDR_ECC
|
||||
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
|
||||
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
|
||||
#endif
|
||||
|
||||
#define CONFIG_ENABLE_36BIT_PHYS
|
||||
|
||||
/*
|
||||
* Config the L3 Cache as L3 SRAM
|
||||
*/
|
||||
#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000
|
||||
#define CONFIG_SYS_L3_SIZE (512 << 10)
|
||||
#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
|
||||
#define SPL_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024)
|
||||
#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024)
|
||||
#define CONFIG_SPL_RELOC_MALLOC_SIZE (50 << 10)
|
||||
#define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024)
|
||||
|
||||
#define CONFIG_SYS_DCSRBAR 0xf0000000
|
||||
#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
|
||||
|
||||
/*
|
||||
* DDR Setup
|
||||
*/
|
||||
#define CONFIG_VERY_BIG_RAM
|
||||
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
|
||||
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
|
||||
|
||||
#define CONFIG_DIMM_SLOTS_PER_CTLR 2
|
||||
#define CONFIG_CHIP_SELECTS_PER_CTRL 4
|
||||
|
||||
#define CONFIG_DDR_SPD
|
||||
|
||||
/*
|
||||
* IFC Definitions
|
||||
*/
|
||||
#define CONFIG_SYS_FLASH_BASE 0xe0000000
|
||||
#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
|
||||
|
||||
#ifdef CONFIG_SPL_BUILD
|
||||
#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
|
||||
#else
|
||||
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
|
||||
#endif
|
||||
|
||||
#define CONFIG_HWCONFIG
|
||||
|
||||
/* define to use L1 as initial stack */
|
||||
#define CONFIG_L1_INIT_RAM
|
||||
#define CONFIG_SYS_INIT_RAM_LOCK
|
||||
#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
|
||||
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
|
||||
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000
|
||||
/* The assembler doesn't like typecast */
|
||||
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
|
||||
((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
|
||||
CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
|
||||
#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
|
||||
|
||||
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
|
||||
GENERATED_GBL_DATA_SIZE)
|
||||
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
||||
|
||||
#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
|
||||
#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
|
||||
|
||||
/* Serial Port - controlled on board with jumper J8
|
||||
* open - index 2
|
||||
* shorted - index 1
|
||||
*/
|
||||
#define CONFIG_SYS_NS16550_SERIAL
|
||||
#define CONFIG_SYS_NS16550_REG_SIZE 1
|
||||
#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
|
||||
|
||||
#define CONFIG_SYS_BAUDRATE_TABLE \
|
||||
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
|
||||
|
||||
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
|
||||
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
|
||||
#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
|
||||
#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
|
||||
|
||||
/* I2C */
|
||||
#define CONFIG_SYS_I2C_LEGACY
|
||||
#define CONFIG_SYS_I2C_FSL
|
||||
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
|
||||
#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
|
||||
#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
|
||||
#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
|
||||
|
||||
/*
|
||||
* RapidIO
|
||||
*/
|
||||
#define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000
|
||||
#define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull
|
||||
#define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */
|
||||
|
||||
#define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000
|
||||
#define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull
|
||||
#define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */
|
||||
|
||||
/*
|
||||
* General PCI
|
||||
* Memory space is mapped 1-1, but I/O space must start from 0.
|
||||
*/
|
||||
|
||||
/* controller 1, direct to uli, tgtid 3, Base address 20000 */
|
||||
#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
|
||||
#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
|
||||
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
|
||||
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
|
||||
#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
|
||||
#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
|
||||
#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
|
||||
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
|
||||
|
||||
/* controller 2, Slot 2, tgtid 2, Base address 201000 */
|
||||
#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
|
||||
#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
|
||||
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
|
||||
#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
|
||||
#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
|
||||
#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
|
||||
#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
|
||||
#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
|
||||
|
||||
/* controller 3, Slot 1, tgtid 1, Base address 202000 */
|
||||
#define CONFIG_SYS_PCIE3_MEM_VIRT 0xc0000000
|
||||
#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
|
||||
#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull
|
||||
#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
|
||||
#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
|
||||
#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
|
||||
#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
|
||||
#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
|
||||
|
||||
/* controller 4, Base address 203000 */
|
||||
#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000
|
||||
#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc60000000ull
|
||||
#define CONFIG_SYS_PCIE4_MEM_SIZE 0x20000000 /* 512M */
|
||||
#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000
|
||||
#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull
|
||||
#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */
|
||||
|
||||
#ifdef CONFIG_PCI
|
||||
#define CONFIG_PCI_INDIRECT_BRIDGE
|
||||
|
||||
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
|
||||
#endif /* CONFIG_PCI */
|
||||
|
||||
/* SATA */
|
||||
#ifdef CONFIG_FSL_SATA_V2
|
||||
#define CONFIG_SYS_SATA_MAX_DEVICE 2
|
||||
#define CONFIG_SATA1
|
||||
#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
|
||||
#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
|
||||
#define CONFIG_SATA2
|
||||
#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR
|
||||
#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
|
||||
|
||||
#define CONFIG_LBA48
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_FMAN_ENET
|
||||
#define CONFIG_ETHPRIME "FM1@DTSEC1"
|
||||
#endif
|
||||
|
||||
/*
|
||||
* Environment
|
||||
*/
|
||||
#define CONFIG_LOADS_ECHO /* echo on for serial download */
|
||||
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
|
||||
|
||||
/*
|
||||
* Miscellaneous configurable options
|
||||
*/
|
||||
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
|
||||
|
||||
/*
|
||||
* For booting Linux, the board info and command line data
|
||||
* have to be in the first 64 MB of memory, since this is
|
||||
* the maximum mapped by the Linux kernel during initialization.
|
||||
*/
|
||||
#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/
|
||||
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
|
||||
|
||||
#ifdef CONFIG_CMD_KGDB
|
||||
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
|
||||
#endif
|
||||
|
||||
/*
|
||||
* Environment Configuration
|
||||
*/
|
||||
#define CONFIG_ROOTPATH "/opt/nfsroot"
|
||||
#define CONFIG_BOOTFILE "uImage"
|
||||
#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server*/
|
||||
|
||||
/* default location for tftp and bootm */
|
||||
#define CONFIG_LOADADDR 1000000
|
||||
|
||||
#define CONFIG_HVBOOT \
|
||||
"setenv bootargs config-addr=0x60000000; " \
|
||||
"bootm 0x01000000 - 0x00f00000"
|
||||
|
||||
#endif /* __CONFIG_H */
|
||||
Loading…
Reference in New Issue
Block a user