ARM: dts: stm32: Split AV96 into DHCOR SoM and AV96 board
The AV96 is in fact an assembly of DH Electronics DHCOR SoM on top of an AV96 reference board. Split the DTs to reflect that and make sure to DHCOR SoM can be reused on other boards easily. It is also highly recommended to configure the board for the DHCOM make stm32mp15_dhcom_basic_defconfig make DEVICE_TREE=stm32mp15xx-dhcor-avenger96 as that permits reusing the board code for the DH components, like accessing and reading out the ethernet MAC from EEPROM. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Change-Id: I7db47280d4eb0d668eb4e006355240271154f97f
This commit is contained in:
Marek Vasut
Patrick Delaunay
parent
e5899099ab
commit
132e5b6898
@ -893,7 +893,8 @@ dtb-$(CONFIG_STM32MP15x) += \
|
||||
stm32mp157c-dk2.dtb \
|
||||
stm32mp157c-ed1.dtb \
|
||||
stm32mp157c-ev1.dtb \
|
||||
stm32mp15xx-dhcom-pdk2.dtb
|
||||
stm32mp15xx-dhcom-pdk2.dtb \
|
||||
stm32mp15xx-dhcor-avenger96.dtb
|
||||
|
||||
dtb-$(CONFIG_SOC_K3_AM6) += k3-am654-base-board.dtb k3-am654-r5-base-board.dtb
|
||||
dtb-$(CONFIG_SOC_K3_J721E) += k3-j721e-common-proc-board.dtb \
|
||||
|
||||
@ -4,423 +4,5 @@
|
||||
* Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "stm32mp157.dtsi"
|
||||
#include "stm32mp15-pinctrl.dtsi"
|
||||
#include "stm32mp15xxac-pinctrl.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/mfd/st,stpmic1.h>
|
||||
|
||||
/ {
|
||||
model = "Arrow Electronics STM32MP157A Avenger96 board";
|
||||
compatible = "arrow,stm32mp157a-avenger96", "st,stm32mp157";
|
||||
|
||||
aliases {
|
||||
eeprom0 = &eeprom0;
|
||||
ethernet0 = ðernet0;
|
||||
mmc0 = &sdmmc1;
|
||||
serial0 = &uart4;
|
||||
serial1 = &uart7;
|
||||
spi0 = &qspi;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
memory@c0000000 {
|
||||
device_type = "memory";
|
||||
reg = <0xc0000000 0x40000000>;
|
||||
};
|
||||
|
||||
led {
|
||||
compatible = "gpio-leds";
|
||||
led1 {
|
||||
label = "green:user0";
|
||||
gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "heartbeat";
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
led2 {
|
||||
label = "green:user1";
|
||||
gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "mmc0";
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
led3 {
|
||||
label = "green:user2";
|
||||
gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "mmc1";
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
led4 {
|
||||
label = "green:user3";
|
||||
gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "none";
|
||||
default-state = "off";
|
||||
panic-indicator;
|
||||
};
|
||||
|
||||
led5 {
|
||||
label = "yellow:wifi";
|
||||
gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "phy0tx";
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
led6 {
|
||||
label = "blue:bt";
|
||||
gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "bluetooth-power";
|
||||
default-state = "off";
|
||||
};
|
||||
};
|
||||
|
||||
sd_switch: regulator-sd_switch {
|
||||
compatible = "regulator-gpio";
|
||||
regulator-name = "sd_switch";
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <2900000>;
|
||||
regulator-type = "voltage";
|
||||
regulator-always-on;
|
||||
|
||||
gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
|
||||
gpios-states = <0>;
|
||||
states = <1800000 0x1>,
|
||||
<2900000 0x0>;
|
||||
};
|
||||
|
||||
/* Enpirion EP3A8LQI U2 on the DHCOR */
|
||||
vdd_io: regulator-buck-io {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "buck-io";
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
vin-supply = <&vdd>;
|
||||
};
|
||||
};
|
||||
|
||||
ðernet0 {
|
||||
status = "okay";
|
||||
pinctrl-0 = <ðernet0_rgmii_pins_b>;
|
||||
pinctrl-1 = <ðernet0_rgmii_pins_sleep_b>;
|
||||
pinctrl-names = "default", "sleep";
|
||||
phy-mode = "rgmii";
|
||||
max-speed = <1000>;
|
||||
phy-handle = <&phy0>;
|
||||
phy-reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
|
||||
|
||||
mdio0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
compatible = "snps,dwmac-mdio";
|
||||
phy0: ethernet-phy@7 {
|
||||
reg = <7>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&i2c1 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&i2c1_pins_b>;
|
||||
i2c-scl-rising-time-ns = <185>;
|
||||
i2c-scl-falling-time-ns = <20>;
|
||||
status = "okay";
|
||||
/delete-property/dmas;
|
||||
/delete-property/dma-names;
|
||||
};
|
||||
|
||||
&i2c2 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&i2c2_pins_b1 &i2c2_pins_b2>;
|
||||
i2c-scl-rising-time-ns = <185>;
|
||||
i2c-scl-falling-time-ns = <20>;
|
||||
status = "okay";
|
||||
/delete-property/dmas;
|
||||
/delete-property/dma-names;
|
||||
};
|
||||
|
||||
&i2c4 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&i2c4_pins_a>;
|
||||
i2c-scl-rising-time-ns = <185>;
|
||||
i2c-scl-falling-time-ns = <20>;
|
||||
status = "okay";
|
||||
/delete-property/dmas;
|
||||
/delete-property/dma-names;
|
||||
|
||||
pmic: stpmic@33 {
|
||||
compatible = "st,stpmic1";
|
||||
reg = <0x33>;
|
||||
interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <2>;
|
||||
status = "okay";
|
||||
|
||||
st,main-control-register = <0x04>;
|
||||
st,vin-control-register = <0xc0>;
|
||||
st,usb-control-register = <0x30>;
|
||||
|
||||
regulators {
|
||||
compatible = "st,stpmic1-regulators";
|
||||
|
||||
ldo1-supply = <&v3v3>;
|
||||
ldo2-supply = <&v3v3>;
|
||||
ldo3-supply = <&vdd_ddr>;
|
||||
ldo5-supply = <&v3v3>;
|
||||
ldo6-supply = <&v3v3>;
|
||||
pwr_sw1-supply = <&bst_out>;
|
||||
pwr_sw2-supply = <&bst_out>;
|
||||
|
||||
vddcore: buck1 {
|
||||
regulator-name = "vddcore";
|
||||
regulator-min-microvolt = <800000>;
|
||||
regulator-max-microvolt = <1350000>;
|
||||
regulator-always-on;
|
||||
regulator-initial-mode = <0>;
|
||||
regulator-over-current-protection;
|
||||
};
|
||||
|
||||
vdd_ddr: buck2 {
|
||||
regulator-name = "vdd_ddr";
|
||||
regulator-min-microvolt = <1350000>;
|
||||
regulator-max-microvolt = <1350000>;
|
||||
regulator-always-on;
|
||||
regulator-initial-mode = <0>;
|
||||
regulator-over-current-protection;
|
||||
};
|
||||
|
||||
vdd: buck3 {
|
||||
regulator-name = "vdd";
|
||||
regulator-min-microvolt = <2900000>;
|
||||
regulator-max-microvolt = <2900000>;
|
||||
regulator-always-on;
|
||||
st,mask_reset;
|
||||
regulator-initial-mode = <0>;
|
||||
regulator-over-current-protection;
|
||||
};
|
||||
|
||||
v3v3: buck4 {
|
||||
regulator-name = "v3v3";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
regulator-always-on;
|
||||
regulator-over-current-protection;
|
||||
regulator-initial-mode = <0>;
|
||||
};
|
||||
|
||||
vdda: ldo1 {
|
||||
regulator-name = "vdda";
|
||||
regulator-min-microvolt = <2900000>;
|
||||
regulator-max-microvolt = <2900000>;
|
||||
interrupts = <IT_CURLIM_LDO1 0>;
|
||||
interrupt-parent = <&pmic>;
|
||||
};
|
||||
|
||||
v2v8: ldo2 {
|
||||
regulator-name = "v2v8";
|
||||
regulator-min-microvolt = <2800000>;
|
||||
regulator-max-microvolt = <2800000>;
|
||||
interrupts = <IT_CURLIM_LDO2 0>;
|
||||
interrupt-parent = <&pmic>;
|
||||
};
|
||||
|
||||
vtt_ddr: ldo3 {
|
||||
regulator-name = "vtt_ddr";
|
||||
regulator-min-microvolt = <500000>;
|
||||
regulator-max-microvolt = <750000>;
|
||||
regulator-always-on;
|
||||
regulator-over-current-protection;
|
||||
};
|
||||
|
||||
vdd_usb: ldo4 {
|
||||
regulator-name = "vdd_usb";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
interrupts = <IT_CURLIM_LDO4 0>;
|
||||
interrupt-parent = <&pmic>;
|
||||
};
|
||||
|
||||
vdd_sd: ldo5 {
|
||||
regulator-name = "vdd_sd";
|
||||
regulator-min-microvolt = <2900000>;
|
||||
regulator-max-microvolt = <2900000>;
|
||||
interrupts = <IT_CURLIM_LDO5 0>;
|
||||
interrupt-parent = <&pmic>;
|
||||
regulator-boot-on;
|
||||
};
|
||||
|
||||
v1v8: ldo6 {
|
||||
regulator-name = "v1v8";
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
interrupts = <IT_CURLIM_LDO6 0>;
|
||||
interrupt-parent = <&pmic>;
|
||||
regulator-enable-ramp-delay = <300000>;
|
||||
};
|
||||
|
||||
vref_ddr: vref_ddr {
|
||||
regulator-name = "vref_ddr";
|
||||
regulator-always-on;
|
||||
regulator-over-current-protection;
|
||||
};
|
||||
|
||||
bst_out: boost {
|
||||
regulator-name = "bst_out";
|
||||
interrupts = <IT_OCP_BOOST 0>;
|
||||
interrupt-parent = <&pmic>;
|
||||
};
|
||||
|
||||
vbus_otg: pwr_sw1 {
|
||||
regulator-name = "vbus_otg";
|
||||
interrupts = <IT_OCP_OTG 0>;
|
||||
interrupt-parent = <&pmic>;
|
||||
regulator-active-discharge = <1>;
|
||||
};
|
||||
|
||||
vbus_sw: pwr_sw2 {
|
||||
regulator-name = "vbus_sw";
|
||||
interrupts = <IT_OCP_SWOUT 0>;
|
||||
interrupt-parent = <&pmic>;
|
||||
regulator-active-discharge = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
onkey {
|
||||
compatible = "st,stpmic1-onkey";
|
||||
interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
|
||||
interrupt-names = "onkey-falling", "onkey-rising";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog {
|
||||
compatible = "st,stpmic1-wdt";
|
||||
status = "disabled";
|
||||
};
|
||||
};
|
||||
|
||||
eeprom0: eeprom@53 {
|
||||
compatible = "atmel,24c02";
|
||||
reg = <0x53>;
|
||||
pagesize = <16>;
|
||||
};
|
||||
};
|
||||
|
||||
&iwdg2 {
|
||||
timeout-sec = <32>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pwr_regulators {
|
||||
vdd-supply = <&vdd_io>;
|
||||
vdd_3v3_usbfs-supply = <&vdd_usb>;
|
||||
};
|
||||
|
||||
&qspi {
|
||||
pinctrl-names = "default", "sleep";
|
||||
pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
|
||||
pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
|
||||
reg = <0x58003000 0x1000>, <0x70000000 0x200000>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "okay";
|
||||
|
||||
flash0: spi-flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-rx-bus-width = <4>;
|
||||
spi-max-frequency = <108000000>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
&rng1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&rtc {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&sdmmc1 {
|
||||
pinctrl-names = "default", "opendrain", "sleep";
|
||||
pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
|
||||
pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
|
||||
pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
|
||||
disable-wp;
|
||||
st,sig-dir;
|
||||
st,neg-edge;
|
||||
st,use-ckin;
|
||||
sd-uhs-sdr104;
|
||||
bus-width = <4>;
|
||||
vmmc-supply = <&vdd_sd>;
|
||||
vqmmc-supply = <&sd_switch>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&sdmmc2 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
|
||||
non-removable;
|
||||
no-sd;
|
||||
no-sdio;
|
||||
st,neg-edge;
|
||||
bus-width = <8>;
|
||||
vmmc-supply = <&v3v3>;
|
||||
mmc-ddr-3_3v;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi2 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&spi2_pins_a>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart4 {
|
||||
/* On Low speed expansion header */
|
||||
label = "LS-UART1";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart4_pins_b>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart7 {
|
||||
/* On Low speed expansion header */
|
||||
label = "LS-UART0";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart7_pins_a>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbh_ehci {
|
||||
phys = <&usbphyc_port0>;
|
||||
phy-names = "usb";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbotg_hs {
|
||||
dr_mode = "peripheral";
|
||||
phys = <&usbphyc_port1 0>;
|
||||
phy-names = "usb2-phy";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbphyc {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbphyc_port0 {
|
||||
phy-supply = <&vdd_usb>;
|
||||
};
|
||||
|
||||
&usbphyc_port1 {
|
||||
phy-supply = <&vdd_usb>;
|
||||
};
|
||||
/* This is kept for backward compatibility and will be removed */
|
||||
#include "stm32mp15xx-dhcor-avenger96.dts"
|
||||
|
||||
83
arch/arm/dts/stm32mp15xx-dhcor-avenger96-u-boot.dtsi
Normal file
83
arch/arm/dts/stm32mp15xx-dhcor-avenger96-u-boot.dtsi
Normal file
@ -0,0 +1,83 @@
|
||||
// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
|
||||
/*
|
||||
* Copyright (C) 2020 Marek Vasut <marex@denx.de>
|
||||
*/
|
||||
|
||||
#include "stm32mp15xx-dhcor-u-boot.dtsi"
|
||||
|
||||
/ {
|
||||
aliases {
|
||||
mmc0 = &sdmmc1;
|
||||
mmc1 = &sdmmc2;
|
||||
usb0 = &usbotg_hs;
|
||||
};
|
||||
|
||||
config {
|
||||
u-boot,boot-led = "led1";
|
||||
u-boot,error-led = "led4";
|
||||
};
|
||||
};
|
||||
|
||||
&sdmmc1 {
|
||||
u-boot,dm-spl;
|
||||
};
|
||||
|
||||
&sdmmc1_b4_pins_a {
|
||||
u-boot,dm-spl;
|
||||
pins1 {
|
||||
u-boot,dm-spl;
|
||||
};
|
||||
pins2 {
|
||||
u-boot,dm-spl;
|
||||
};
|
||||
};
|
||||
|
||||
&sdmmc1_dir_pins_b {
|
||||
u-boot,dm-spl;
|
||||
pins1 {
|
||||
u-boot,dm-spl;
|
||||
};
|
||||
pins2 {
|
||||
u-boot,dm-spl;
|
||||
};
|
||||
};
|
||||
|
||||
&sdmmc2 {
|
||||
u-boot,dm-spl;
|
||||
};
|
||||
|
||||
&sdmmc2_b4_pins_a {
|
||||
u-boot,dm-spl;
|
||||
pins1 {
|
||||
u-boot,dm-spl;
|
||||
};
|
||||
pins2 {
|
||||
u-boot,dm-spl;
|
||||
};
|
||||
};
|
||||
|
||||
&sdmmc2_d47_pins_b {
|
||||
u-boot,dm-spl;
|
||||
pins {
|
||||
u-boot,dm-spl;
|
||||
};
|
||||
};
|
||||
|
||||
&uart4 {
|
||||
u-boot,dm-pre-reloc;
|
||||
};
|
||||
|
||||
&uart4_pins_b {
|
||||
u-boot,dm-pre-reloc;
|
||||
pins1 {
|
||||
u-boot,dm-pre-reloc;
|
||||
};
|
||||
pins2 {
|
||||
u-boot,dm-pre-reloc;
|
||||
};
|
||||
};
|
||||
|
||||
&usbotg_hs {
|
||||
u-boot,force-b-session-valid;
|
||||
hnp-srp-disable;
|
||||
};
|
||||
212
arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts
Normal file
212
arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts
Normal file
@ -0,0 +1,212 @@
|
||||
// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
|
||||
/*
|
||||
* Copyright (C) Linaro Ltd 2019 - All Rights Reserved
|
||||
* Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
||||
* Copyright (C) 2020 Marek Vasut <marex@denx.de>
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "stm32mp15xx-dhcor.dtsi"
|
||||
#include "stm32mp15xx-dhcor-avenger96-u-boot.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Arrow Electronics STM32MP15xx Avenger96 board";
|
||||
compatible = "arrow,stm32mp15xx-avenger96", "st,stm32mp15x";
|
||||
|
||||
aliases {
|
||||
eeprom0 = &eeprom0;
|
||||
ethernet0 = ðernet0;
|
||||
mmc0 = &sdmmc1;
|
||||
serial0 = &uart4;
|
||||
serial1 = &uart7;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
led {
|
||||
compatible = "gpio-leds";
|
||||
led1 {
|
||||
label = "green:user0";
|
||||
gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "heartbeat";
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
led2 {
|
||||
label = "green:user1";
|
||||
gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "mmc0";
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
led3 {
|
||||
label = "green:user2";
|
||||
gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "mmc1";
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
led4 {
|
||||
label = "green:user3";
|
||||
gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "none";
|
||||
default-state = "off";
|
||||
panic-indicator;
|
||||
};
|
||||
|
||||
led5 {
|
||||
label = "yellow:wifi";
|
||||
gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "phy0tx";
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
led6 {
|
||||
label = "blue:bt";
|
||||
gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "bluetooth-power";
|
||||
default-state = "off";
|
||||
};
|
||||
};
|
||||
|
||||
sd_switch: regulator-sd_switch {
|
||||
compatible = "regulator-gpio";
|
||||
regulator-name = "sd_switch";
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <2900000>;
|
||||
regulator-type = "voltage";
|
||||
regulator-always-on;
|
||||
|
||||
gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
|
||||
gpios-states = <0>;
|
||||
states = <1800000 0x1>,
|
||||
<2900000 0x0>;
|
||||
};
|
||||
};
|
||||
|
||||
ðernet0 {
|
||||
status = "okay";
|
||||
pinctrl-0 = <ðernet0_rgmii_pins_b>;
|
||||
pinctrl-1 = <ðernet0_rgmii_pins_sleep_b>;
|
||||
pinctrl-names = "default", "sleep";
|
||||
phy-mode = "rgmii";
|
||||
max-speed = <1000>;
|
||||
phy-handle = <&phy0>;
|
||||
phy-reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
|
||||
|
||||
mdio0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
compatible = "snps,dwmac-mdio";
|
||||
phy0: ethernet-phy@7 {
|
||||
reg = <7>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&i2c1 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&i2c1_pins_b>;
|
||||
i2c-scl-rising-time-ns = <185>;
|
||||
i2c-scl-falling-time-ns = <20>;
|
||||
status = "okay";
|
||||
/delete-property/dmas;
|
||||
/delete-property/dma-names;
|
||||
};
|
||||
|
||||
&i2c2 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&i2c2_pins_b1 &i2c2_pins_b2>;
|
||||
i2c-scl-rising-time-ns = <185>;
|
||||
i2c-scl-falling-time-ns = <20>;
|
||||
status = "okay";
|
||||
/delete-property/dmas;
|
||||
/delete-property/dma-names;
|
||||
};
|
||||
|
||||
&i2c4 {
|
||||
eeprom0: eeprom@53 {
|
||||
compatible = "atmel,24c02";
|
||||
reg = <0x53>;
|
||||
pagesize = <16>;
|
||||
};
|
||||
};
|
||||
|
||||
&sdmmc1 {
|
||||
pinctrl-names = "default", "opendrain", "sleep";
|
||||
pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
|
||||
pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
|
||||
pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
|
||||
disable-wp;
|
||||
st,sig-dir;
|
||||
st,neg-edge;
|
||||
st,use-ckin;
|
||||
sd-uhs-sdr104;
|
||||
bus-width = <4>;
|
||||
vmmc-supply = <&vdd_sd>;
|
||||
vqmmc-supply = <&sd_switch>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&sdmmc2 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
|
||||
non-removable;
|
||||
no-sd;
|
||||
no-sdio;
|
||||
st,neg-edge;
|
||||
bus-width = <8>;
|
||||
vmmc-supply = <&v3v3>;
|
||||
mmc-ddr-3_3v;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi2 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&spi2_pins_a>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart4 {
|
||||
/* On Low speed expansion header */
|
||||
label = "LS-UART1";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart4_pins_b>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart7 {
|
||||
/* On Low speed expansion header */
|
||||
label = "LS-UART0";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&uart7_pins_a>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbh_ehci {
|
||||
phys = <&usbphyc_port0>;
|
||||
phy-names = "usb";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbotg_hs {
|
||||
dr_mode = "peripheral";
|
||||
phys = <&usbphyc_port1 0>;
|
||||
phy-names = "usb2-phy";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbphyc {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbphyc_port0 {
|
||||
phy-supply = <&vdd_usb>;
|
||||
};
|
||||
|
||||
&usbphyc_port1 {
|
||||
phy-supply = <&vdd_usb>;
|
||||
};
|
||||
@ -4,25 +4,13 @@
|
||||
*
|
||||
* Copyright (C) Linaro Ltd 2019 - All Rights Reserved
|
||||
* Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
||||
* Copyright (C) 2020 Marek Vasut <marex@denx.de>
|
||||
*/
|
||||
|
||||
#include <dt-bindings/clock/stm32mp1-clksrc.h>
|
||||
#include "stm32mp15-u-boot.dtsi"
|
||||
#include "stm32mp15-ddr3-2x4Gb-1066-binG.dtsi"
|
||||
|
||||
/ {
|
||||
aliases {
|
||||
mmc0 = &sdmmc1;
|
||||
mmc1 = &sdmmc2;
|
||||
usb0 = &usbotg_hs;
|
||||
};
|
||||
|
||||
config {
|
||||
u-boot,boot-led = "led1";
|
||||
u-boot,error-led = "led4";
|
||||
};
|
||||
};
|
||||
|
||||
&i2c4 {
|
||||
u-boot,dm-pre-reloc;
|
||||
};
|
||||
@ -38,6 +26,10 @@
|
||||
u-boot,dm-pre-reloc;
|
||||
};
|
||||
|
||||
&qspi {
|
||||
u-boot,dm-spl;
|
||||
};
|
||||
|
||||
&rcc {
|
||||
st,clksrc = <
|
||||
CLK_MPU_PLL1P
|
||||
@ -138,67 +130,3 @@
|
||||
u-boot,dm-pre-reloc;
|
||||
};
|
||||
};
|
||||
|
||||
&sdmmc1 {
|
||||
u-boot,dm-spl;
|
||||
};
|
||||
|
||||
&sdmmc1_b4_pins_a {
|
||||
u-boot,dm-spl;
|
||||
pins1 {
|
||||
u-boot,dm-spl;
|
||||
};
|
||||
pins2 {
|
||||
u-boot,dm-spl;
|
||||
};
|
||||
};
|
||||
|
||||
&sdmmc1_dir_pins_b {
|
||||
u-boot,dm-spl;
|
||||
pins1 {
|
||||
u-boot,dm-spl;
|
||||
};
|
||||
pins2 {
|
||||
u-boot,dm-spl;
|
||||
};
|
||||
};
|
||||
|
||||
&sdmmc2 {
|
||||
u-boot,dm-spl;
|
||||
};
|
||||
|
||||
&sdmmc2_b4_pins_a {
|
||||
u-boot,dm-spl;
|
||||
pins1 {
|
||||
u-boot,dm-spl;
|
||||
};
|
||||
pins2 {
|
||||
u-boot,dm-spl;
|
||||
};
|
||||
};
|
||||
|
||||
&sdmmc2_d47_pins_b {
|
||||
u-boot,dm-spl;
|
||||
pins {
|
||||
u-boot,dm-spl;
|
||||
};
|
||||
};
|
||||
|
||||
&uart4 {
|
||||
u-boot,dm-pre-reloc;
|
||||
};
|
||||
|
||||
&uart4_pins_b {
|
||||
u-boot,dm-pre-reloc;
|
||||
pins1 {
|
||||
u-boot,dm-pre-reloc;
|
||||
};
|
||||
pins2 {
|
||||
u-boot,dm-pre-reloc;
|
||||
};
|
||||
};
|
||||
|
||||
&usbotg_hs {
|
||||
u-boot,force-b-session-valid;
|
||||
hnp-srp-disable;
|
||||
};
|
||||
232
arch/arm/dts/stm32mp15xx-dhcor.dtsi
Normal file
232
arch/arm/dts/stm32mp15xx-dhcor.dtsi
Normal file
@ -0,0 +1,232 @@
|
||||
// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
|
||||
/*
|
||||
* Copyright (C) Linaro Ltd 2019 - All Rights Reserved
|
||||
* Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
||||
* Copyright (C) 2020 Marek Vasut <marex@denx.de>
|
||||
*/
|
||||
/dts-v1/;
|
||||
|
||||
#include "stm32mp157.dtsi"
|
||||
#include "stm32mp15-pinctrl.dtsi"
|
||||
#include "stm32mp15xxac-pinctrl.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/mfd/st,stpmic1.h>
|
||||
|
||||
/ {
|
||||
aliases {
|
||||
spi0 = &qspi;
|
||||
};
|
||||
|
||||
memory@c0000000 {
|
||||
device_type = "memory";
|
||||
reg = <0xc0000000 0x40000000>;
|
||||
};
|
||||
|
||||
/* Enpirion EP3A8LQI U2 on the DHCOR */
|
||||
vdd_io: regulator-buck-io {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "buck-io";
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
vin-supply = <&vdd>;
|
||||
};
|
||||
};
|
||||
|
||||
&i2c4 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&i2c4_pins_a>;
|
||||
i2c-scl-rising-time-ns = <185>;
|
||||
i2c-scl-falling-time-ns = <20>;
|
||||
status = "okay";
|
||||
/delete-property/dmas;
|
||||
/delete-property/dma-names;
|
||||
|
||||
pmic: stpmic@33 {
|
||||
compatible = "st,stpmic1";
|
||||
reg = <0x33>;
|
||||
interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <2>;
|
||||
status = "okay";
|
||||
|
||||
st,main-control-register = <0x04>;
|
||||
st,vin-control-register = <0xc0>;
|
||||
st,usb-control-register = <0x30>;
|
||||
|
||||
regulators {
|
||||
compatible = "st,stpmic1-regulators";
|
||||
|
||||
ldo1-supply = <&v3v3>;
|
||||
ldo2-supply = <&v3v3>;
|
||||
ldo3-supply = <&vdd_ddr>;
|
||||
ldo5-supply = <&v3v3>;
|
||||
ldo6-supply = <&v3v3>;
|
||||
pwr_sw1-supply = <&bst_out>;
|
||||
pwr_sw2-supply = <&bst_out>;
|
||||
|
||||
vddcore: buck1 {
|
||||
regulator-name = "vddcore";
|
||||
regulator-min-microvolt = <800000>;
|
||||
regulator-max-microvolt = <1350000>;
|
||||
regulator-always-on;
|
||||
regulator-initial-mode = <0>;
|
||||
regulator-over-current-protection;
|
||||
};
|
||||
|
||||
vdd_ddr: buck2 {
|
||||
regulator-name = "vdd_ddr";
|
||||
regulator-min-microvolt = <1350000>;
|
||||
regulator-max-microvolt = <1350000>;
|
||||
regulator-always-on;
|
||||
regulator-initial-mode = <0>;
|
||||
regulator-over-current-protection;
|
||||
};
|
||||
|
||||
vdd: buck3 {
|
||||
regulator-name = "vdd";
|
||||
regulator-min-microvolt = <2900000>;
|
||||
regulator-max-microvolt = <2900000>;
|
||||
regulator-always-on;
|
||||
st,mask_reset;
|
||||
regulator-initial-mode = <0>;
|
||||
regulator-over-current-protection;
|
||||
};
|
||||
|
||||
v3v3: buck4 {
|
||||
regulator-name = "v3v3";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
regulator-always-on;
|
||||
regulator-over-current-protection;
|
||||
regulator-initial-mode = <0>;
|
||||
};
|
||||
|
||||
vdda: ldo1 {
|
||||
regulator-name = "vdda";
|
||||
regulator-min-microvolt = <2900000>;
|
||||
regulator-max-microvolt = <2900000>;
|
||||
interrupts = <IT_CURLIM_LDO1 0>;
|
||||
interrupt-parent = <&pmic>;
|
||||
};
|
||||
|
||||
v2v8: ldo2 {
|
||||
regulator-name = "v2v8";
|
||||
regulator-min-microvolt = <2800000>;
|
||||
regulator-max-microvolt = <2800000>;
|
||||
interrupts = <IT_CURLIM_LDO2 0>;
|
||||
interrupt-parent = <&pmic>;
|
||||
};
|
||||
|
||||
vtt_ddr: ldo3 {
|
||||
regulator-name = "vtt_ddr";
|
||||
regulator-min-microvolt = <500000>;
|
||||
regulator-max-microvolt = <750000>;
|
||||
regulator-always-on;
|
||||
regulator-over-current-protection;
|
||||
};
|
||||
|
||||
vdd_usb: ldo4 {
|
||||
regulator-name = "vdd_usb";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
interrupts = <IT_CURLIM_LDO4 0>;
|
||||
interrupt-parent = <&pmic>;
|
||||
};
|
||||
|
||||
vdd_sd: ldo5 {
|
||||
regulator-name = "vdd_sd";
|
||||
regulator-min-microvolt = <2900000>;
|
||||
regulator-max-microvolt = <2900000>;
|
||||
interrupts = <IT_CURLIM_LDO5 0>;
|
||||
interrupt-parent = <&pmic>;
|
||||
regulator-boot-on;
|
||||
};
|
||||
|
||||
v1v8: ldo6 {
|
||||
regulator-name = "v1v8";
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
interrupts = <IT_CURLIM_LDO6 0>;
|
||||
interrupt-parent = <&pmic>;
|
||||
regulator-enable-ramp-delay = <300000>;
|
||||
};
|
||||
|
||||
vref_ddr: vref_ddr {
|
||||
regulator-name = "vref_ddr";
|
||||
regulator-always-on;
|
||||
regulator-over-current-protection;
|
||||
};
|
||||
|
||||
bst_out: boost {
|
||||
regulator-name = "bst_out";
|
||||
interrupts = <IT_OCP_BOOST 0>;
|
||||
interrupt-parent = <&pmic>;
|
||||
};
|
||||
|
||||
vbus_otg: pwr_sw1 {
|
||||
regulator-name = "vbus_otg";
|
||||
interrupts = <IT_OCP_OTG 0>;
|
||||
interrupt-parent = <&pmic>;
|
||||
regulator-active-discharge = <1>;
|
||||
};
|
||||
|
||||
vbus_sw: pwr_sw2 {
|
||||
regulator-name = "vbus_sw";
|
||||
interrupts = <IT_OCP_SWOUT 0>;
|
||||
interrupt-parent = <&pmic>;
|
||||
regulator-active-discharge = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
onkey {
|
||||
compatible = "st,stpmic1-onkey";
|
||||
interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
|
||||
interrupt-names = "onkey-falling", "onkey-rising";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog {
|
||||
compatible = "st,stpmic1-wdt";
|
||||
status = "disabled";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&iwdg2 {
|
||||
timeout-sec = <32>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pwr_regulators {
|
||||
vdd-supply = <&vdd_io>;
|
||||
vdd_3v3_usbfs-supply = <&vdd_usb>;
|
||||
};
|
||||
|
||||
&qspi {
|
||||
pinctrl-names = "default", "sleep";
|
||||
pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
|
||||
pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
|
||||
reg = <0x58003000 0x1000>, <0x70000000 0x200000>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "okay";
|
||||
|
||||
flash0: spi-flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-rx-bus-width = <4>;
|
||||
spi-max-frequency = <108000000>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
&rng1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&rtc {
|
||||
status = "okay";
|
||||
};
|
||||
@ -51,11 +51,11 @@ And the necessary drivers
|
||||
|
||||
Currently the following boards are supported:
|
||||
|
||||
+ stm32mp157a-avenger96.dts
|
||||
+ stm32mp157a-dk1.dts
|
||||
+ stm32mp157c-dk2.dts
|
||||
+ stm32mp157c-ed1.dts
|
||||
+ stm32mp157c-ev1.dts
|
||||
+ stm32mp15xx-dhcor-avenger96.dts
|
||||
|
||||
Boot Sequences
|
||||
--------------
|
||||
@ -153,9 +153,9 @@ the supported device trees for STM32MP15x are:
|
||||
|
||||
+ stm32mp157c-dk2
|
||||
|
||||
+ avenger96: Avenger96 board from Arrow Electronics
|
||||
+ avenger96: Avenger96 board from Arrow Electronics based on DH Elec. DHCOR SoM
|
||||
|
||||
+ stm32mp157a-avenger96
|
||||
+ stm32mp15xx-dhcor-avenger96
|
||||
|
||||
Build Procedure
|
||||
---------------
|
||||
@ -237,7 +237,7 @@ Build Procedure
|
||||
|
||||
# export KBUILD_OUTPUT=stm32mp15_basic
|
||||
# make stm32mp15_basic_defconfig
|
||||
# make DEVICE_TREE=stm32mp157a-avenger96 all
|
||||
# make DEVICE_TREE=stm32mp15xx-dhcor-avenger96 all
|
||||
|
||||
6. Output files
|
||||
|
||||
|
||||
Loading…
Reference in New Issue
Block a user