leandrof/u-boot
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
70be2fcadc
u-boot/configs/ls1021aqds_ddr4_nor_defconfig

70 lines
1.4 KiB
Plaintext
Raw Normal View History

board/ls1021aqds: Add DDR4 support LS1021AQDS has a variant with DDR4 slot. This patch adds a new defconfig for this variant to enable DDR4 support. RAW timing parameters are not added for DDR4. The board timing parameters are only tuned for single- rank 1600 and 1800MT/s with Micron DIMM 9ASF51272AZ-2G1A1 due to DIMM availability. Signed-off-by: York Sun <yorksun@freescale.com> CC: Alison Wang <alison.wang@freescale.com>
2014-09-11 20:32:07 +00:00
CONFIG_ARM=y
CONFIG_TARGET_LS1021AQDS=y
configs: Migrate CONFIG_SYS_TEXT_BASE On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-03 17:10:38 +00:00
CONFIG_SYS_TEXT_BASE=0x60100000
env: Finish migration of common ENV options - In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-19 01:02:10 +00:00
CONFIG_ENV_SIZE=0x2000
configs: Migrate CONFIG_NR_DRAM_BANKS We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-16 12:16:24 +00:00
CONFIG_NR_DRAM_BANKS=1
env: Finish migration of common ENV options - In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-19 01:02:10 +00:00
CONFIG_ENV_SECT_SIZE=0x20000
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-29 19:54:04 +00:00
CONFIG_AHCI=y
arm: ls1021a: Enable CONFIG_OF_LIBFDT and CONFIG_FIT in defconfig In defconfig, enable CONFIG_OF_LIBFDT to support booting DT linux kernel and enable COFNIG_FIT to support FIT image. Signed-off-by: Alison Wang <alison.wang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-04 04:45:55 +00:00
CONFIG_FIT=y
CONFIG_FIT_VERBOSE=y
common: bootdelay: move CONFIG_BOOTDELAY into a Kconfig option move CONFIG_BOOTDELAY into a Kconfig option. Used for this purpose the moveconfig.py tool in tools. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2016-06-07 06:31:14 +00:00
CONFIG_OF_BOARD_SETUP=y
CONFIG_OF_STDOUT_VIA_ALIAS=y
CONFIG_BOOTDELAY=3
Convert SILENT_CONSOLE options to Kconfig Move these option to Kconfig and tidy up existing uses. The Power PC boards don't have a suitable common element: the common header files don't appear to line up with the Kconfig files as far as I can tell. This results in a lot of defconfig changes. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jteki@openedev.com> [trini: Re-migrate, update common/console.c logic] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-10-18 02:12:35 +00:00
CONFIG_SILENT_CONSOLE=y
Convert CONFIG_SYS_CONSOLE_IS_IN_ENV and CONFIG_CONSOLE_MUX to Kconfig This converts the following to Kconfig: CONFIG_SYS_CONSOLE_IS_IN_ENV CONFIG_CONSOLE_MUX Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Re-order, re-migrate] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-10-18 02:12:37 +00:00
# CONFIG_CONSOLE_MUX is not set
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
Convert CONFIG_MISC_INIT_R to Kconfig This converts the following to Kconfig: CONFIG_MISC_INIT_R Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Update the defaults logic slightly] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-07-29 18:13:29 +00:00
CONFIG_MISC_INIT_R=y
configs: Re-sync HUSH options Move all cases of CONFIG_SYS_HUSH_PARSER out of the config.h files. Remove all cases of CONFIG_SYS_PROMPT_HUSH_PS2 as everyone uses the default. Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-22 01:37:19 +00:00
CONFIG_HUSH_PARSER=y
configs: Re-sync with cmd/Kconfig Update the config.h and defconfig files for the commands that 8e3c036 converted over to Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-24 21:29:26 +00:00
CONFIG_CMD_BOOTZ=y
cmd: Toggle the default value of CONFIG_CMD_IMLS Having this as a 'default y' is rather annoying because it doesn't actually compile unless other options are defined in the board header: ../cmd/bootm.c: In function 'do_imls_nor': ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'? i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) { Make it 'default n' so people who develop new boards that start from a blank defconfig have one less compilation failure to debug. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-10-08 18:48:01 +00:00
CONFIG_CMD_IMLS=y
configs: Re-sync with cmd/Kconfig Update the config.h and defconfig files for the commands that 8e3c036 converted over to Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-24 21:29:26 +00:00
CONFIG_CMD_GREPENV=y
configs: Re-sync almost all of cmd/Kconfig This syncs up the current cmd/Kconfig and include/configs/ files with the only exception being CMD_NAND. Due to how we have used this historically we need to take further care here when converting. Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-22 20:41:25 +00:00
CONFIG_CMD_MEMINFO=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-14 23:58:53 +00:00
CONFIG_CMD_MEMTEST=y
cmd, disk: convert CONFIG_PARTITION_UUIDS, CMD_PART and CMD_GPT We convert CONFIG_PARTITION_UUIDS to Kconfig first. But in order to cleanly update all of the config files we must also update CMD_PART and CMD_GPT to also be in Kconfig in order to avoid complex logic elsewhere to update all of the config files. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-27 10:00:42 +00:00
CONFIG_CMD_GPT=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-14 23:58:53 +00:00
CONFIG_CMD_I2C=y
configs: Re-sync with cmd/Kconfig Update the config.h and defconfig files for the commands that 8e3c036 converted over to Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-24 21:29:26 +00:00
CONFIG_CMD_MMC=y
configs: Migrate CMD_NAND* Migrate all remaining instances of CMD_NAND, CMD_NAND_TRIMFFS CMD_NAND_LOCK_UNLOCK and CMD_NAND_TORTURE from the headers into the defconfig files. Tested-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-07-29 01:31:42 +00:00
CONFIG_CMD_NAND=y
configs: Re-sync almost all of cmd/Kconfig This syncs up the current cmd/Kconfig and include/configs/ files with the only exception being CMD_NAND. Due to how we have used this historically we need to take further care here when converting. Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-22 20:41:25 +00:00
CONFIG_CMD_USB=y
Move defaults from config_cmd_default.h to Kconfig This sets the default commands Kconfig to match include/config_cmd_default.h commands in the common/Kconfig and removes them from include/configs. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates] Signed-off-by: Tom Rini <trini@konsulko.com>
2015-06-22 21:15:30 +00:00
# CONFIG_CMD_SETEXPR is not set
configs: Re-sync almost all of cmd/Kconfig This syncs up the current cmd/Kconfig and include/configs/ files with the only exception being CMD_NAND. Due to how we have used this historically we need to take further care here when converting. Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-22 20:41:25 +00:00
CONFIG_CMD_DHCP=y
configs: Re-sync with cmd/Kconfig Update the config.h and defconfig files for the commands that 8e3c036 converted over to Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-24 21:29:26 +00:00
CONFIG_CMD_MII=y
configs: Re-sync almost all of cmd/Kconfig This syncs up the current cmd/Kconfig and include/configs/ files with the only exception being CMD_NAND. Due to how we have used this historically we need to take further care here when converting. Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-22 20:41:25 +00:00
CONFIG_CMD_PING=y
Convert CONFIG_CMD_BMP to Kconfig This converts the following to Kconfig: CONFIG_CMD_BMP Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Add depends on LCD || DM_VIDEO || VIDEO] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-27 04:27:55 +00:00
CONFIG_CMD_BMP=y
configs: Re-sync with cmd/Kconfig Update the config.h and defconfig files for the commands that 8e3c036 converted over to Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
2016-04-24 21:29:26 +00:00
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
arm: ls1021aqds: Convert to driver model and enable serial support Split duart configuration as device tree file. Move /chosen node out of board commone device tree. Convert ls1021aqds nor and SD configurations to driver model support (qspi already uses DM). Enable ns16550 DM serial driver for nor configurations. Signed-off-by: York Sun <york.sun@nxp.com> CC: Alison Wang <alison.wang@nxp.com> CC: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Alison Wang <alison.wang@nxp.com>
2016-02-08 21:04:17 +00:00
CONFIG_OF_CONTROL=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-03 19:26:12 +00:00
CONFIG_DEFAULT_DEVICE_TREE="ls1021a-qds-duart"
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-28 11:16:32 +00:00
CONFIG_ENV_IS_IN_FLASH=y
env: Finish migration of common ENV options - In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-19 01:02:10 +00:00
CONFIG_ENV_ADDR=0x60300000
arm: ls1021aqds: Convert to driver model and enable serial support Split duart configuration as device tree file. Move /chosen node out of board commone device tree. Convert ls1021aqds nor and SD configurations to driver model support (qspi already uses DM). Enable ns16550 DM serial driver for nor configurations. Signed-off-by: York Sun <york.sun@nxp.com> CC: Alison Wang <alison.wang@nxp.com> CC: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Alison Wang <alison.wang@nxp.com>
2016-02-08 21:04:17 +00:00
CONFIG_DM=y
configs: ls1021a: enable sata configs for all ls1021a defconfigs Add CONFIG_AHCI CONFIG_SATA_CEVA CONFIG_DM_SCSI for some ls1021a defconfigs that missing one of them or more. enable CONFIG_DM_MMC for some defconfigs to support CONFIG_BLK Support sata for all ls1021a defconfigs Signed-off-by: Peng Ma <peng.ma@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-01-30 11:19:40 +00:00
CONFIG_SATA_CEVA=y
Freescale/NXP: Migrate CONFIG_FSL_CAAM to defconfigs In some cases this is absolutely required, so select this for some secure features. This also requires migration of RSA_FREESCALE_EXP Cc: Ruchika Gupta <ruchika.gupta@nxp.com> Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com> Cc: Naveen Burmi <NaveenBurmi@freescale.com> Cc: Po Liu <po.liu@freescale.com> Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com> Cc: Priyanka Jain <Priyanka.Jain@freescale.com> Cc: Sumit Garg <sumit.garg@nxp.com> Cc: Shaohui Xie <Shaohui.Xie@freescale.com> Cc: Chunhe Lan <Chunhe.Lan@freescale.com> Cc: Feng Li <feng.li_2@nxp.com> Cc: Alison Wang <alison.wang@freescale.com> Cc: Mingkai Hu <Mingkai.Hu@freescale.com> Cc: York Sun <york.sun@nxp.com> Cc: Saksham Jain <saksham.jain@nxp.freescale.com> Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-01 21:51:58 +00:00
CONFIG_FSL_CAAM=y
configs: ls1021a: enable sata configs for all ls1021a defconfigs Add CONFIG_AHCI CONFIG_SATA_CEVA CONFIG_DM_SCSI for some ls1021a defconfigs that missing one of them or more. enable CONFIG_DM_MMC for some defconfigs to support CONFIG_BLK Support sata for all ls1021a defconfigs Signed-off-by: Peng Ma <peng.ma@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-01-30 11:19:40 +00:00
CONFIG_DM_MMC=y
treewide: Migrate CONFIG_FSL_ESDHC to Kconfig Migrate the CONFIG_FSL_ESDHC option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-03-28 12:38:19 +00:00
CONFIG_FSL_ESDHC=y
mtd: rename CONFIG_MTD_DEVICE -> CONFIG_MTD Like in Linux, just use CONFIG_MTD to compile the MTD stack. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-10-03 17:50:05 +00:00
CONFIG_MTD=y
flash: complete CONFIG_SYS_NO_FLASH move with renaming We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is not completed. Finish this work by the tool. During this move, let's rename it to CONFIG_MTD_NOR_FLASH. Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH" than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will make the code more readable. Besides, negative meaning symbols do not fit in obj-$(CONFIG_...) style Makefiles. This commit was created as follows: [1] Edit "default n" to "default y" in the config entry in common/Kconfig. [2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH" [3] Rename the instances in defconfigs by the following: find . -path './configs/*_defconfig' | xargs sed -i \ -e '/CONFIG_SYS_NO_FLASH=y/d' \ -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/' [4] Change the conditionals by the following: find . -name '*.[ch]' | xargs sed -i \ -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \ -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \ -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \ -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/' [5] Modify the following manually - Rename the rest of instances - Remove the description from README - Create the new Kconfig entry in drivers/mtd/Kconfig - Remove the old Kconfig entry from common/Kconfig - Remove the garbage comments from include/configs/*.h Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-11 13:43:54 +00:00
CONFIG_MTD_NOR_FLASH=y
Convert CONFIG_FLASH_CFI_DRIVER et al to Kconfig This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-migrate] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-14 20:10:50 +00:00
CONFIG_FLASH_CFI_DRIVER=y
CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
CONFIG_SYS_FLASH_CFI=y
mtd: rename CONFIG_NAND -> CONFIG_MTD_RAW_NAND Add more clarity by changing the Kconfig entry name. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> [trini: Re-run migration, update a few more cases] Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-10-03 17:50:03 +00:00
CONFIG_MTD_RAW_NAND=y
configs: Finish migration of PHY_GIGE Reviewed-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-08 02:00:34 +00:00
CONFIG_PHY_GIGE=y
net: Move CONFIG_E1000 options to Kconfig Move config for the E1000 Ethernet driver to Kconfig and tidy up affected boards. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-08-19 15:33:43 +00:00
CONFIG_E1000=y
Convert CONFIG_MII et al to Kconfig This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-07-21 04:03:57 +00:00
CONFIG_MII=y
treewide: Migrate CONFIG_TSEC_ENET to Kconfig Migrate the CONFIG_TSEC_ENET option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-03-28 12:38:18 +00:00
CONFIG_TSEC_ENET=y
cmd, disk: convert CONFIG_PARTITION_UUIDS, CMD_PART and CMD_GPT We convert CONFIG_PARTITION_UUIDS to Kconfig first. But in order to cleanly update all of the config files we must also update CMD_PART and CMD_GPT to also be in Kconfig in order to avoid complex logic elsewhere to update all of the config files. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-27 10:00:42 +00:00
CONFIG_PCI=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
CONFIG_PCIE_LAYERSCAPE=y
configs: ls1021a: enable sata configs for all ls1021a defconfigs Add CONFIG_AHCI CONFIG_SATA_CEVA CONFIG_DM_SCSI for some ls1021a defconfigs that missing one of them or more. enable CONFIG_DM_MMC for some defconfigs to support CONFIG_BLK Support sata for all ls1021a defconfigs Signed-off-by: Peng Ma <peng.ma@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-01-30 11:19:40 +00:00
CONFIG_DM_SCSI=y
Convert all of CONFIG_CONS_INDEX to Kconfig This converts the following to Kconfig: CONFIG_CONS_INDEX We have existing entries for this option in a number of places, with different guards on them. They're also sometimes used for things not directly inside of the serial driver. First, introduce a new symbol to guard the use of CONFIG_CONS_INDEX, so that in the case where we don't need this for the serial driver, but for some other use, we can still do it. Next, consolidate all of these into the single entry in drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that we can imply a correct value here to make the defconfig side of this smaller. Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rework a lot of the logic here, such that I took authorship from Adam, but kept his S-o-B line] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-03-07 00:02:27 +00:00
CONFIG_SPECIFY_CONSOLE_INDEX=y
configs: Resync with savedefconfig Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-08 20:11:59 +00:00
CONFIG_DM_SERIAL=y
ns16550: move CONFIG_SYS_NS16550 to Kconfig Move CONFIG_SYS_NS16550 to Kconfig, and run moveconfig.py. Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
2015-11-19 13:48:14 +00:00
CONFIG_SYS_NS16550=y
usb: move CONFIG_USB_XHCI to Kconfig with renaming Move CONFIG_USB_XHCI to defconfig files for all boards, renaming it into CONFIG_USB_XHCI_HCD. As commented in the help of "config USB_XHCI" entry, this has been a TODO for a long time; now CONFIG_USB_XHCI_HCD and CONFIG_USB_XHCI have been unified in favor of the former. Note: Some boards define CONFIG_USB_XHCI in their headers without CONFIG_USB, which does not meet the "depends on" in Kconfig. I added CONFIG_USB=y for those boards when converting. Otherwise, they would fail to build. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-06-03 22:35:03 +00:00
CONFIG_USB=y
configs: Resync with savedefconfig Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-08 20:11:59 +00:00
CONFIG_DM_USB=y
usb: move CONFIG_USB_XHCI to Kconfig with renaming Move CONFIG_USB_XHCI to defconfig files for all boards, renaming it into CONFIG_USB_XHCI_HCD. As commented in the help of "config USB_XHCI" entry, this has been a TODO for a long time; now CONFIG_USB_XHCI_HCD and CONFIG_USB_XHCI have been unified in favor of the former. Note: Some boards define CONFIG_USB_XHCI in their headers without CONFIG_USB, which does not meet the "depends on" in Kconfig. I added CONFIG_USB=y for those boards when converting. Otherwise, they would fail to build. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-06-03 22:35:03 +00:00
CONFIG_USB_XHCI_HCD=y
usb: move CONFIG_USB_XHCI_DWC3 to Kconfig Create an entry for "config USB_XHCI_DWC3" in Kconfig and switch over to it for all boards. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-06-03 22:35:04 +00:00
CONFIG_USB_XHCI_DWC3=y
configs: Migrate CONFIG_USB_STORAGE In some cases we were missing CONFIG_USB=y so enable that when needed. Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-08 20:31:26 +00:00
CONFIG_USB_STORAGE=y
Convert CONFIG_FSL_DCU_FB to Kconfig Rename CONFIG_FSL_DCU_FB to CONFIG_VIDEO_FSL_DCU_FB and convert it to Kconfig. Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com> Reviewed-by: Stefan Agner <stefan.agner@toradex.com> Reviewed-by: Alison Wang <alison.wang@nxp.com>
2017-04-11 05:42:09 +00:00
CONFIG_VIDEO_FSL_DCU_FB=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-30 16:58:33 +00:00
CONFIG_VIDEO=y
configs: Re-sync Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-01 15:41:11 +00:00
# CONFIG_VIDEO_SW_CURSOR is not set
Reference in New Issue Copy Permalink