forked from Minki/linux
7c10093692
On non-BIOS platforms it is possible that the BIOS data area contains garbage instead of being zeroed or something equivalent (firmware people: we are talking of 1.5K here, so please do the sane thing.) We need on the order of 20-30K of low memory in order to boot, which may grow up to < 64K in the future. We probably want to avoid the lowest of the low memory. At the same time, it seems extremely unlikely that a legitimate EBDA would ever reach down to the 128K (which would require it to be over half a megabyte in size.) Thus, pick 128K as the cutoff for "this is insane, ignore." We may still end up reserving a bunch of extra memory on the low megabyte, but that is not really a major issue these days. In the worst case we lose 512K of RAM. This code really should be merged with trim_bios_range() in arch/x86/kernel/setup.c, but that is a bigger patch for a later merge window. Reported-by: Darren Hart <dvhart@linux.intel.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Cc: Matt Fleming <matt.fleming@intel.com> Cc: <stable@vger.kernel.org> Link: http://lkml.kernel.org/n/tip-oebml055yyfm8yxmria09rja@git.kernel.org
72 lines
2.2 KiB
C
72 lines
2.2 KiB
C
#include <linux/kernel.h>
|
|
#include <linux/init.h>
|
|
#include <linux/memblock.h>
|
|
|
|
#include <asm/setup.h>
|
|
#include <asm/bios_ebda.h>
|
|
|
|
/*
|
|
* The BIOS places the EBDA/XBDA at the top of conventional
|
|
* memory, and usually decreases the reported amount of
|
|
* conventional memory (int 0x12) too. This also contains a
|
|
* workaround for Dell systems that neglect to reserve EBDA.
|
|
* The same workaround also avoids a problem with the AMD768MPX
|
|
* chipset: reserve a page before VGA to prevent PCI prefetch
|
|
* into it (errata #56). Usually the page is reserved anyways,
|
|
* unless you have no PS/2 mouse plugged in.
|
|
*
|
|
* This functions is deliberately very conservative. Losing
|
|
* memory in the bottom megabyte is rarely a problem, as long
|
|
* as we have enough memory to install the trampoline. Using
|
|
* memory that is in use by the BIOS or by some DMA device
|
|
* the BIOS didn't shut down *is* a big problem.
|
|
*/
|
|
|
|
#define BIOS_LOWMEM_KILOBYTES 0x413
|
|
#define LOWMEM_CAP 0x9f000U /* Absolute maximum */
|
|
#define INSANE_CUTOFF 0x20000U /* Less than this = insane */
|
|
|
|
void __init reserve_ebda_region(void)
|
|
{
|
|
unsigned int lowmem, ebda_addr;
|
|
|
|
/*
|
|
* To determine the position of the EBDA and the
|
|
* end of conventional memory, we need to look at
|
|
* the BIOS data area. In a paravirtual environment
|
|
* that area is absent. We'll just have to assume
|
|
* that the paravirt case can handle memory setup
|
|
* correctly, without our help.
|
|
*/
|
|
if (paravirt_enabled())
|
|
return;
|
|
|
|
/* end of low (conventional) memory */
|
|
lowmem = *(unsigned short *)__va(BIOS_LOWMEM_KILOBYTES);
|
|
lowmem <<= 10;
|
|
|
|
/* start of EBDA area */
|
|
ebda_addr = get_bios_ebda();
|
|
|
|
/*
|
|
* Note: some old Dells seem to need 4k EBDA without
|
|
* reporting so, so just consider the memory above 0x9f000
|
|
* to be off limits (bugzilla 2990).
|
|
*/
|
|
|
|
/* If the EBDA address is below 128K, assume it is bogus */
|
|
if (ebda_addr < INSANE_CUTOFF)
|
|
ebda_addr = LOWMEM_CAP;
|
|
|
|
/* If lowmem is less than 128K, assume it is bogus */
|
|
if (lowmem < INSANE_CUTOFF)
|
|
lowmem = LOWMEM_CAP;
|
|
|
|
/* Use the lower of the lowmem and EBDA markers as the cutoff */
|
|
lowmem = min(lowmem, ebda_addr);
|
|
lowmem = min(lowmem, LOWMEM_CAP); /* Absolute cap */
|
|
|
|
/* reserve all memory between lowmem and the 1MB mark */
|
|
memblock_reserve(lowmem, 0x100000 - lowmem);
|
|
}
|