forked from Minki/linux
606ea9fa0b
On newer hardware revisions, there is no need to write the host's counter at the end of a RX transaction. The same applies to writing the number of packets at the end of a TX transaction. It is generally a good idea to avoid unnecessary SDIO/SPI transfers. Throughput and CPU usage are improved when avoiding these. Send the host's RX counter and the TX packet count only if needed, based on the hardware revision. [Changed WL12XX_QUIRK_END_OF_TRANSACTION to use BIT(0) -- Luca] Signed-off-by: Ido Yariv <ido@wizery.com> Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Reviewed-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
78 lines
2.1 KiB
C
78 lines
2.1 KiB
C
/*
|
|
* This file is part of wl1271
|
|
*
|
|
* Copyright (C) 2008-2009 Nokia Corporation
|
|
*
|
|
* Contact: Luciano Coelho <luciano.coelho@nokia.com>
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* version 2 as published by the Free Software Foundation.
|
|
*
|
|
* This program is distributed in the hope that it will be useful, but
|
|
* WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
|
|
* General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
|
|
* 02110-1301 USA
|
|
*
|
|
*/
|
|
|
|
#ifndef __BOOT_H__
|
|
#define __BOOT_H__
|
|
|
|
#include "wl12xx.h"
|
|
|
|
int wl1271_boot(struct wl1271 *wl);
|
|
int wl1271_load_firmware(struct wl1271 *wl);
|
|
|
|
#define WL1271_NO_SUBBANDS 8
|
|
#define WL1271_NO_POWER_LEVELS 4
|
|
#define WL1271_FW_VERSION_MAX_LEN 20
|
|
|
|
struct wl1271_static_data {
|
|
u8 mac_address[ETH_ALEN];
|
|
u8 padding[2];
|
|
u8 fw_version[WL1271_FW_VERSION_MAX_LEN];
|
|
u32 hw_version;
|
|
u8 tx_power_table[WL1271_NO_SUBBANDS][WL1271_NO_POWER_LEVELS];
|
|
};
|
|
|
|
/* number of times we try to read the INIT interrupt */
|
|
#define INIT_LOOP 20000
|
|
|
|
/* delay between retries */
|
|
#define INIT_LOOP_DELAY 50
|
|
|
|
#define WU_COUNTER_PAUSE_VAL 0x3FF
|
|
#define WELP_ARM_COMMAND_VAL 0x4
|
|
|
|
#define OCP_REG_POLARITY 0x0064
|
|
#define OCP_REG_CLK_TYPE 0x0448
|
|
#define OCP_REG_CLK_POLARITY 0x0cb2
|
|
#define OCP_REG_CLK_PULL 0x0cb4
|
|
|
|
#define REG_FUSE_DATA_2_1 0x050a
|
|
#define PG_VER_MASK 0x3c
|
|
#define PG_VER_OFFSET 2
|
|
|
|
#define PG_MAJOR_VER_MASK 0x3
|
|
#define PG_MAJOR_VER_OFFSET 0x0
|
|
#define PG_MINOR_VER_MASK 0xc
|
|
#define PG_MINOR_VER_OFFSET 0x2
|
|
|
|
#define CMD_MBOX_ADDRESS 0x407B4
|
|
|
|
#define POLARITY_LOW BIT(1)
|
|
#define NO_PULL (BIT(14) | BIT(15))
|
|
|
|
#define FREF_CLK_TYPE_BITS 0xfffffe7f
|
|
#define CLK_REQ_PRCM 0x100
|
|
#define FREF_CLK_POLARITY_BITS 0xfffff8ff
|
|
#define CLK_REQ_OUTN_SEL 0x700
|
|
|
|
#endif
|