linux/drivers/usb
Mathias Nyman d590c23111 usb: Avoid unnecessary LPM enabling and disabling during suspend and resume
The original motivation for disabling/enabling Link PM at device
suspend/resume was to force link state to go via U0 before suspend sets
the link state to U3. Going directly from U2 to U3 is not allowed.

Disabling LPM will forced the link state to U0, but will send a lot of
Set port feature requests for evert suspend and resume.

This is not needed as Hub hardware will take care of going via U0
when a U2 -> U3 transition is requested [1]

[1] USB 3.1 specification section 10.16.2.10 Set Port Feature:

"If the value is 3, then host software wants to selectively suspend the
device connected to this port. The hub shall transition the link to U3
from any of the other U states using allowed link state transitions.
If the port is not already in the U0 state, then it shall transition the
port to the U0 state and then initiate the transition to U3.
While this state is active, the hub does not propagate downstream-directed
traffic to this port, but the hub will respond to resume signaling from the
port"

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-06-15 22:17:46 +02:00
..
atm usb: atm: remove unnecessary code 2017-03-16 17:58:44 +09:00
c67x00
chipidea Merge 4.12-rc5 into usb-next 2017-06-12 08:43:53 +02:00
class usb: cdc-wdm: use memdup_user 2017-05-17 12:20:53 +02:00
common DeviceTree for 4.12: 2017-05-05 19:33:07 -07:00
core usb: Avoid unnecessary LPM enabling and disabling during suspend and resume 2017-06-15 22:17:46 +02:00
dwc2 usb: dwc2: add support for the DWC2 controller on Meson8 SoCs 2017-06-02 11:27:36 +03:00
dwc3 usb: dwc3: keystone: check return value 2017-05-16 14:11:04 +03:00
early usb/early: Remove trace_printk() callers in xhci-dbc 2017-06-13 10:54:40 +02:00
gadget Merge 4.12-rc5 into usb-next 2017-06-12 08:43:53 +02:00
host usb: host: ehci-exynos: Handle return value of clk_prepare_enable 2017-06-13 10:48:24 +02:00
image sched/headers: Prepare to move signal wakeup & sigpending methods from <linux/sched.h> into <linux/sched/signal.h> 2017-03-02 08:42:32 +01:00
isp1760 usb: add CONFIG_USB_PCI for system have both PCI HW and non-PCI based USB HW 2017-03-17 13:16:56 +09:00
misc usb: misc: usbsevseg: Use sysfs_match_string() helper 2017-06-13 10:54:40 +02:00
mon sched/headers: Prepare to move signal wakeup & sigpending methods from <linux/sched.h> into <linux/sched/signal.h> 2017-03-02 08:42:32 +01:00
mtu3 usb: mtu3: Handle return value of clk_prepare_enable 2017-06-13 10:54:40 +02:00
musb usb: musb: dsps: keep VBUS on for host-only mode 2017-05-27 11:54:46 +02:00
phy usb: changes for v4.12 2017-04-11 16:47:26 +02:00
renesas_usbhs usb: renesas_usbhs: Replace the deprecated extcon API 2017-01-24 11:04:14 +02:00
serial USB: serial: qcserial: add more Lenovo EM74xx device IDs 2017-05-17 17:10:57 +02:00
storage Merge 4.12-rc2 into usb-next 2017-05-22 09:00:23 +02:00
typec usb: typec: Add a sysfs node to manage port type 2017-06-03 18:02:58 +09:00
usbip usbip: vhci-hcd: Clean up the code by adding a new macro 2017-06-13 10:51:10 +02:00
wusbcore USB: wusbcore: fix NULL-deref at probe 2017-03-14 17:07:30 +08:00
Kconfig usb: USB Type-C connector class 2017-03-23 13:48:44 +01:00
Makefile USB patches for 4.12-rc1 2017-05-04 18:03:51 -07:00
README
usb-skeleton.c USB: usb-skeleton: refactor endpoint retrieval 2017-03-23 13:54:08 +01:00

To understand all the Linux-USB framework, you'll use these resources:

    * This source code.  This is necessarily an evolving work, and
      includes kerneldoc that should help you get a current overview.
      ("make pdfdocs", and then look at "usb.pdf" for host side and
      "gadget.pdf" for peripheral side.)  Also, Documentation/usb has
      more information.

    * The USB 2.0 specification (from www.usb.org), with supplements
      such as those for USB OTG and the various device classes.
      The USB specification has a good overview chapter, and USB
      peripherals conform to the widely known "Chapter 9".

    * Chip specifications for USB controllers.  Examples include
      host controllers (on PCs, servers, and more); peripheral
      controllers (in devices with Linux firmware, like printers or
      cell phones); and hard-wired peripherals like Ethernet adapters.

    * Specifications for other protocols implemented by USB peripheral
      functions.  Some are vendor-specific; others are vendor-neutral
      but just standardized outside of the www.usb.org team.

Here is a list of what each subdirectory here is, and what is contained in
them.

core/		- This is for the core USB host code, including the
		  usbfs files and the hub class driver ("hub_wq").

host/		- This is for USB host controller drivers.  This
		  includes UHCI, OHCI, EHCI, and others that might
		  be used with more specialized "embedded" systems.

gadget/		- This is for USB peripheral controller drivers and
		  the various gadget drivers which talk to them.


Individual USB driver directories.  A new driver should be added to the
first subdirectory in the list below that it fits into.

image/		- This is for still image drivers, like scanners or
		  digital cameras.
../input/	- This is for any driver that uses the input subsystem,
		  like keyboard, mice, touchscreens, tablets, etc.
../media/	- This is for multimedia drivers, like video cameras,
		  radios, and any other drivers that talk to the v4l
		  subsystem.
../net/		- This is for network drivers.
serial/		- This is for USB to serial drivers.
storage/	- This is for USB mass-storage drivers.
class/		- This is for all USB device drivers that do not fit
		  into any of the above categories, and work for a range
		  of USB Class specified devices. 
misc/		- This is for all USB device drivers that do not fit
		  into any of the above categories.