cc62a7eb63
There are cases, when 80% max isochronous bandwidth is too limiting.
For example I have two USB video capture cards which stream uncompressed
video, and to stream full NTSC + PAL videos we'd need
NTSC 640x480 YUV422 @30fps ~17.6 MB/s
PAL 720x576 YUV422 @25fps ~19.7 MB/s
isoc bandwidth.
Now, due to limited alt settings in capture devices NTSC one ends up
streaming with max_pkt_size=2688 and PAL with max_pkt_size=2892, both
with interval=1. In terms of microframe time allocation this gives
NTSC ~53us
PAL ~57us
and together
~110us > 100us == 80% of 125us uframe time.
So those two devices can't work together simultaneously because the'd
over allocate isochronous bandwidth.
80% seemed a bit arbitrary to me, and I've tried to raise it to 90% and
both devices started to work together, so I though sometimes it would be
a good idea for users to override hardcoded default of max 80% isoc
bandwidth.
After all, isn't it a user who should decide how to load the bus? If I
can live with 10% or even 5% bulk bandwidth that should be ok. I'm a USB
newcomer, but that 80% set in stone by USB 2.0 specification seems to be
chosen pretty arbitrary to me, just to serve as a reasonable default.
NOTE 1
~~~~~~
for two streams with max_pkt_size=3072 (worst case) both time
allocation would be 60us+60us=120us which is 96% periodic bandwidth
leaving 4% for bulk and control. Alan Stern suggested that bulk then
would be problematic (less than 300*8 bittimes left per microframe), but
I think that is still enough for control traffic.
NOTE 2
~~~~~~
Sarah Sharp expressed concern that maxing out periodic bandwidth
could lead to vendor-specific hardware bugs on host controllers, because
> It's entirely possible that you'll run into
> vendor-specific bugs if you try to pack the schedule with isochronous
> transfers. I don't think any hardware designer would seriously test or
> validate their hardware with a schedule that is basically a violation of
> the USB bus spec (more than 80% for periodic transfers).
So far I've only tested this patch on my HP Mini 5103 with N10 chipset
kirr@mini:~$ lspci
00:00.0 Host bridge: Intel Corporation N10 Family DMI Bridge
00:02.0 VGA compatible controller: Intel Corporation N10 Family Integrated Graphics Controller
00:02.1 Display controller: Intel Corporation N10 Family Integrated Graphics Controller
00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02)
00:1c.3 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 4 (rev 02)
00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02)
00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02)
00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation NM10 Family LPC Controller (rev 02)
00:1f.2 SATA controller: Intel Corporation N10/ICH7 Family SATA AHCI Controller (rev 02)
01:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01)
02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8059 PCI-E Gigabit Ethernet Controller (rev 11)
and the system works stable with 110us/uframe (~88%) isoc bandwith allocated for
above-mentioned isochronous transfers.
NOTE 3
~~~~~~
This feature is off by default. I mean max periodic bandwidth is set to
100us/uframe by default exactly as it was before the patch. So only those of us
who need the extreme settings are taking the risk - normal users who do not
alter uframe_periodic_max sysfs attribute should not see any change at all.
NOTE 4
~~~~~~
I've tried to update documentation in Documentation/ABI/ thoroughly, but
only "TBD" was put into Documentation/usb/ehci.txt -- the text there seems
to be outdated and much needing refreshing, before it could be amended.
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
||
|---|---|---|
| .. | ||
| obsolete | ||
| removed | ||
| stable | ||
| testing | ||
| README | ||
This directory attempts to document the ABI between the Linux kernel and userspace, and the relative stability of these interfaces. Due to the everchanging nature of Linux, and the differing maturity levels, these interfaces should be used by userspace programs in different ways. We have four different levels of ABI stability, as shown by the four different subdirectories in this location. Interfaces may change levels of stability according to the rules described below. The different levels of stability are: stable/ This directory documents the interfaces that the developer has defined to be stable. Userspace programs are free to use these interfaces with no restrictions, and backward compatibility for them will be guaranteed for at least 2 years. Most interfaces (like syscalls) are expected to never change and always be available. testing/ This directory documents interfaces that are felt to be stable, as the main development of this interface has been completed. The interface can be changed to add new features, but the current interface will not break by doing this, unless grave errors or security problems are found in them. Userspace programs can start to rely on these interfaces, but they must be aware of changes that can occur before these interfaces move to be marked stable. Programs that use these interfaces are strongly encouraged to add their name to the description of these interfaces, so that the kernel developers can easily notify them if any changes occur (see the description of the layout of the files below for details on how to do this.) obsolete/ This directory documents interfaces that are still remaining in the kernel, but are marked to be removed at some later point in time. The description of the interface will document the reason why it is obsolete and when it can be expected to be removed. The file Documentation/feature-removal-schedule.txt may describe some of these interfaces, giving a schedule for when they will be removed. removed/ This directory contains a list of the old interfaces that have been removed from the kernel. Every file in these directories will contain the following information: What: Short description of the interface Date: Date created KernelVersion: Kernel version this feature first showed up in. Contact: Primary contact for this interface (may be a mailing list) Description: Long description of the interface and how to use it. Users: All users of this interface who wish to be notified when it changes. This is very important for interfaces in the "testing" stage, so that kernel developers can work with userspace developers to ensure that things do not break in ways that are unacceptable. It is also important to get feedback for these interfaces to make sure they are working in a proper way and do not need to be changed further. How things move between levels: Interfaces in stable may move to obsolete, as long as the proper notification is given. Interfaces may be removed from obsolete and the kernel as long as the documented amount of time has gone by. Interfaces in the testing state can move to the stable state when the developers feel they are finished. They cannot be removed from the kernel tree without going through the obsolete state first. It's up to the developer to place their interfaces in the category they wish for it to start out in.