forked from Minki/linux
92f8629b60
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
118 lines
1.8 KiB
Plaintext
118 lines
1.8 KiB
Plaintext
/*
|
|
* usb_a926x.dts - Device Tree file for Caloa USB A926x board
|
|
*
|
|
* Copyright (C) 2011-2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
*
|
|
* Licensed under GPLv2 or later.
|
|
*/
|
|
|
|
/ {
|
|
clocks {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges;
|
|
|
|
main_clock: clock@0 {
|
|
compatible = "atmel,osc", "fixed-clock";
|
|
clock-frequency = <12000000>;
|
|
};
|
|
};
|
|
|
|
ahb {
|
|
apb {
|
|
dbgu: serial@fffff200 {
|
|
status = "okay";
|
|
};
|
|
|
|
macb0: ethernet@fffc4000 {
|
|
phy-mode = "rmii";
|
|
status = "okay";
|
|
};
|
|
|
|
usb1: gadget@fffa4000 {
|
|
atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>;
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
nand0: nand@40000000 {
|
|
nand-bus-width = <8>;
|
|
nand-ecc-mode = "soft";
|
|
nand-on-flash-bbt;
|
|
status = "okay";
|
|
|
|
at91bootstrap@0 {
|
|
label = "at91bootstrap";
|
|
reg = <0x0 0x20000>;
|
|
};
|
|
|
|
barebox@20000 {
|
|
label = "barebox";
|
|
reg = <0x20000 0x40000>;
|
|
};
|
|
|
|
bareboxenv@60000 {
|
|
label = "bareboxenv";
|
|
reg = <0x60000 0x20000>;
|
|
};
|
|
|
|
bareboxenv2@80000 {
|
|
label = "bareboxenv2";
|
|
reg = <0x80000 0x20000>;
|
|
};
|
|
|
|
oftree@80000 {
|
|
label = "oftree";
|
|
reg = <0xa0000 0x20000>;
|
|
};
|
|
|
|
kernel@a0000 {
|
|
label = "kernel";
|
|
reg = <0xc0000 0x400000>;
|
|
};
|
|
|
|
rootfs@4a0000 {
|
|
label = "rootfs";
|
|
reg = <0x4c0000 0x7800000>;
|
|
};
|
|
|
|
data@7ca0000 {
|
|
label = "data";
|
|
reg = <0x7cc0000 0x8340000>;
|
|
};
|
|
};
|
|
|
|
usb0: ohci@00500000 {
|
|
num-ports = <2>;
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
user_led {
|
|
label = "user_led";
|
|
gpios = <&pioB 21 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "heartbeat";
|
|
};
|
|
};
|
|
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
user_pb {
|
|
label = "user_pb";
|
|
gpios = <&pioB 10 GPIO_ACTIVE_LOW>;
|
|
linux,code = <28>;
|
|
gpio-key,wakeup;
|
|
};
|
|
};
|
|
|
|
i2c@0 {
|
|
status = "okay";
|
|
};
|
|
};
|