forked from Minki/linux
99eb8a550d
The arm26 port has been in a state where it was far from even compiling for quite some time. Ian Molton agreed with the removal. Signed-off-by: Adrian Bunk <bunk@stusta.de> Cc: Ian Molton <spyro@f2s.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
85 lines
2.8 KiB
Plaintext
85 lines
2.8 KiB
Plaintext
#
|
|
# SCSI driver configuration for Acorn
|
|
#
|
|
config SCSI_ACORNSCSI_3
|
|
tristate "Acorn SCSI card (aka30) support"
|
|
depends on ARCH_ACORN && SCSI && BROKEN
|
|
select SCSI_SPI_ATTRS
|
|
help
|
|
This enables support for the Acorn SCSI card (aka30). If you have an
|
|
Acorn system with one of these, say Y. If unsure, say N.
|
|
|
|
config SCSI_ACORNSCSI_TAGGED_QUEUE
|
|
bool "Support SCSI 2 Tagged queueing"
|
|
depends on SCSI_ACORNSCSI_3
|
|
help
|
|
Say Y here to enable tagged queuing support on the Acorn SCSI card.
|
|
|
|
This is a feature of SCSI-2 which improves performance: the host
|
|
adapter can send several SCSI commands to a device's queue even if
|
|
previous commands haven't finished yet. Some SCSI devices don't
|
|
implement this properly, so the safe answer is N.
|
|
|
|
config SCSI_ACORNSCSI_SYNC
|
|
bool "Support SCSI 2 Synchronous Transfers"
|
|
depends on SCSI_ACORNSCSI_3
|
|
help
|
|
Say Y here to enable synchronous transfer negotiation with all
|
|
targets on the Acorn SCSI card.
|
|
|
|
In general, this improves performance; however some SCSI devices
|
|
don't implement it properly, so the safe answer is N.
|
|
|
|
config SCSI_ARXESCSI
|
|
tristate "ARXE SCSI support"
|
|
depends on ARCH_ACORN && SCSI
|
|
help
|
|
Around 1991, Arxe Systems Limited released a high density floppy
|
|
disc interface for the Acorn Archimedes range, to allow the use of
|
|
HD discs from the then new A5000 on earlier models. This interface
|
|
was either sold on its own or with an integral SCSI controller.
|
|
Technical details on this NCR53c94-based device are available at
|
|
<http://www.cryton.demon.co.uk/acornbits/scsi_arxe.html>
|
|
Say Y here to compile in support for the SCSI controller.
|
|
|
|
config SCSI_CUMANA_2
|
|
tristate "CumanaSCSI II support"
|
|
depends on ARCH_ACORN && SCSI
|
|
help
|
|
This enables support for the Cumana SCSI II card. If you have an
|
|
Acorn system with one of these, say Y. If unsure, say N.
|
|
|
|
config SCSI_EESOXSCSI
|
|
tristate "EESOX support"
|
|
depends on ARCH_ACORN && SCSI
|
|
help
|
|
This enables support for the EESOX SCSI card. If you have an Acorn
|
|
system with one of these, say Y, otherwise say N.
|
|
|
|
config SCSI_POWERTECSCSI
|
|
tristate "PowerTec support"
|
|
depends on ARCH_ACORN && SCSI
|
|
help
|
|
This enables support for the Powertec SCSI card on Acorn systems. If
|
|
you have one of these, say Y. If unsure, say N.
|
|
|
|
comment "The following drivers are not fully supported"
|
|
depends on ARCH_ACORN && EXPERIMENTAL
|
|
|
|
config SCSI_CUMANA_1
|
|
tristate "CumanaSCSI I support (EXPERIMENTAL)"
|
|
depends on ARCH_ACORN && EXPERIMENTAL && SCSI
|
|
select SCSI_SPI_ATTRS
|
|
help
|
|
This enables support for the Cumana SCSI I card. If you have an
|
|
Acorn system with one of these, say Y. If unsure, say N.
|
|
|
|
config SCSI_OAK1
|
|
tristate "Oak SCSI support (EXPERIMENTAL)"
|
|
depends on ARCH_ACORN && EXPERIMENTAL && SCSI
|
|
select SCSI_SPI_ATTRS
|
|
help
|
|
This enables support for the Oak SCSI card. If you have an Acorn
|
|
system with one of these, say Y. If unsure, say N.
|
|
|