forked from Minki/linux
4fb62ededf
The registers used to configure and set the multifunction pins on the 5272 ColdFire are defined as absolute addresses. So the use of them does not need to be offset relative to the peripheral region address. Fix two cases of incorrect usage of these addresses. Both affect UART initialization, one in the common UART pin setup code, the other in the NETtel board specific UART signal handling. Signed-off-by: Greg Ungerer <gerg@uclinux.org>
106 lines
2.9 KiB
C
106 lines
2.9 KiB
C
/****************************************************************************/
|
|
|
|
/*
|
|
* nettel.h -- Lineo (formerly Moreton Bay) NETtel support.
|
|
*
|
|
* (C) Copyright 1999-2000, Moreton Bay (www.moretonbay.com)
|
|
* (C) Copyright 2000-2001, Lineo Inc. (www.lineo.com)
|
|
* (C) Copyright 2001-2002, SnapGear Inc., (www.snapgear.com)
|
|
*/
|
|
|
|
/****************************************************************************/
|
|
#ifndef nettel_h
|
|
#define nettel_h
|
|
/****************************************************************************/
|
|
|
|
|
|
/****************************************************************************/
|
|
#ifdef CONFIG_NETtel
|
|
/****************************************************************************/
|
|
|
|
#ifdef CONFIG_COLDFIRE
|
|
#include <asm/coldfire.h>
|
|
#include <asm/mcfsim.h>
|
|
#include <asm/io.h>
|
|
#endif
|
|
|
|
/*---------------------------------------------------------------------------*/
|
|
#if defined(CONFIG_M5307)
|
|
/*
|
|
* NETtel/5307 based hardware first. DTR/DCD lines are wired to
|
|
* GPIO lines. Most of the LED's are driver through a latch
|
|
* connected to CS2.
|
|
*/
|
|
#define MCFPP_DCD1 0x0001
|
|
#define MCFPP_DCD0 0x0002
|
|
#define MCFPP_DTR1 0x0004
|
|
#define MCFPP_DTR0 0x0008
|
|
|
|
#define NETtel_LEDADDR 0x30400000
|
|
|
|
#ifndef __ASSEMBLY__
|
|
|
|
extern volatile unsigned short ppdata;
|
|
|
|
/*
|
|
* These functions defined to give quasi generic access to the
|
|
* PPIO bits used for DTR/DCD.
|
|
*/
|
|
static __inline__ unsigned int mcf_getppdata(void)
|
|
{
|
|
volatile unsigned short *pp;
|
|
pp = (volatile unsigned short *) MCFSIM_PADAT;
|
|
return((unsigned int) *pp);
|
|
}
|
|
|
|
static __inline__ void mcf_setppdata(unsigned int mask, unsigned int bits)
|
|
{
|
|
volatile unsigned short *pp;
|
|
pp = (volatile unsigned short *) MCFSIM_PADAT;
|
|
ppdata = (ppdata & ~mask) | bits;
|
|
*pp = ppdata;
|
|
}
|
|
#endif
|
|
|
|
/*---------------------------------------------------------------------------*/
|
|
#elif defined(CONFIG_M5206e)
|
|
/*
|
|
* NETtel/5206e based hardware has leds on latch on CS3.
|
|
* No support modem for lines??
|
|
*/
|
|
#define NETtel_LEDADDR 0x50000000
|
|
|
|
/*---------------------------------------------------------------------------*/
|
|
#elif defined(CONFIG_M5272)
|
|
/*
|
|
* NETtel/5272 based hardware. DTR/DCD lines are wired to GPB lines.
|
|
*/
|
|
#define MCFPP_DCD0 0x0080
|
|
#define MCFPP_DCD1 0x0000 /* Port 1 no DCD support */
|
|
#define MCFPP_DTR0 0x0040
|
|
#define MCFPP_DTR1 0x0000 /* Port 1 no DTR support */
|
|
|
|
#ifndef __ASSEMBLY__
|
|
/*
|
|
* These functions defined to give quasi generic access to the
|
|
* PPIO bits used for DTR/DCD.
|
|
*/
|
|
static __inline__ unsigned int mcf_getppdata(void)
|
|
{
|
|
return readw(MCFSIM_PBDAT);
|
|
}
|
|
|
|
static __inline__ void mcf_setppdata(unsigned int mask, unsigned int bits)
|
|
{
|
|
write((readw(MCFSIM_PBDAT) & ~mask) | bits, MCFSIM_PBDAT);
|
|
}
|
|
#endif
|
|
|
|
#endif
|
|
/*---------------------------------------------------------------------------*/
|
|
|
|
/****************************************************************************/
|
|
#endif /* CONFIG_NETtel */
|
|
/****************************************************************************/
|
|
#endif /* nettel_h */
|