leandrof/linux
1
0
Fork 0
forked from Minki/linux
Code Issues Pull Requests Packages Projects Releases Wiki Activity
a1628604fd
linux/arch/arm/mach-omap2/board-overo.c
Tomi Valkeinen 45a279c5ae ARM: OMAP: overo: use new display drivers 
Use the new display drivers for OMAP3 Overo board.

The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.

Note that the LCD add-on boards for lcd43 and lcd35 use the same GPIOs
for the panels. This means that both panel devices cannot be probed at
the same time.

DT will handle this correctly, i.e. the DT data will contain the panel
device only for the add-on board that is attached. However, for the
board file we need a hackish solution: We parse the kernel boot command
line, and see whether lcd43 or lcd35 is set as a default display, and
add the given one. Or, if neither is given, default to lcd43.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
2013-08-28 10:23:19 +03:00

573 lines
14 KiB
C
Raw Blame History

/*
* board-overo.c (Gumstix Overo)
*
* Initial code: Steve Sakoman <steve@sakoman.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
* 02110-1301 USA
*
*/
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/init.h>
#include <linux/io.h>
#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/platform_device.h>
#include <linux/i2c/twl.h>
#include <linux/regulator/machine.h>
#include <linux/regulator/fixed.h>
#include <linux/spi/spi.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <linux/mmc/host.h>
#include <linux/usb/phy.h>
#include <linux/platform_data/mtd-nand-omap2.h>
#include <linux/platform_data/spi-omap2-mcspi.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
#include <video/omapdss.h>
#include <video/omap-panel-data.h>
#include "common.h"
#include "mux.h"
#include "sdram-micron-mt46h32m32lf-6.h"
#include "gpmc.h"
#include "hsmmc.h"
#include "board-flash.h"
#include "common-board-devices.h"
#define NAND_CS 0
#define OVERO_GPIO_BT_XGATE 15
#define OVERO_GPIO_W2W_NRESET 16
#define OVERO_GPIO_PENDOWN 114
#define OVERO_GPIO_BT_NRESET 164
#define OVERO_GPIO_USBH_CPEN 168
#define OVERO_GPIO_USBH_NRESET 183
#define OVERO_SMSC911X_CS 5
#define OVERO_SMSC911X_GPIO 176
#define OVERO_SMSC911X_NRESET 64
#define OVERO_SMSC911X2_CS 4
#define OVERO_SMSC911X2_GPIO 65
/* whether to register LCD35 instead of LCD43 */
static bool overo_use_lcd35;
#if defined(CONFIG_TOUCHSCREEN_ADS7846) || \
defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
/* fixed regulator for ads7846 */
static struct regulator_consumer_supply ads7846_supply[] = {
REGULATOR_SUPPLY("vcc", "spi1.0"),
};
static struct regulator_init_data vads7846_regulator = {
.constraints = {
.valid_ops_mask = REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = ARRAY_SIZE(ads7846_supply),
.consumer_supplies = ads7846_supply,
};
static struct fixed_voltage_config vads7846 = {
.supply_name = "vads7846",
.microvolts = 3300000, /* 3.3V */
.gpio = -EINVAL,
.startup_delay = 0,
.init_data = &vads7846_regulator,
};
static struct platform_device vads7846_device = {
.name = "reg-fixed-voltage",
.id = 1,
.dev = {
.platform_data = &vads7846,
},
};
static void __init overo_ads7846_init(void)
{
omap_ads7846_init(1, OVERO_GPIO_PENDOWN, 0, NULL);
platform_device_register(&vads7846_device);
}
#else
static inline void __init overo_ads7846_init(void) { return; }
#endif
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
#include <linux/smsc911x.h>
#include "gpmc-smsc911x.h"
static struct omap_smsc911x_platform_data smsc911x_cfg = {
.id = 0,
.cs = OVERO_SMSC911X_CS,
.gpio_irq = OVERO_SMSC911X_GPIO,
.gpio_reset = OVERO_SMSC911X_NRESET,
.flags = SMSC911X_USE_32BIT,
};
static struct omap_smsc911x_platform_data smsc911x2_cfg = {
.id = 1,
.cs = OVERO_SMSC911X2_CS,
.gpio_irq = OVERO_SMSC911X2_GPIO,
.gpio_reset = -EINVAL,
.flags = SMSC911X_USE_32BIT,
};
static void __init overo_init_smsc911x(void)
{
gpmc_smsc911x_init(&smsc911x_cfg);
gpmc_smsc911x_init(&smsc911x2_cfg);
}
#else
static inline void __init overo_init_smsc911x(void) { return; }
#endif
/* DSS */
#define OVERO_GPIO_LCD_EN 144
#define OVERO_GPIO_LCD_BL 145
static struct connector_atv_platform_data overo_tv_pdata = {
.name = "tv",
.source = "venc.0",
.connector_type = OMAP_DSS_VENC_TYPE_SVIDEO,
.invert_polarity = false,
};
static struct platform_device overo_tv_connector_device = {
.name = "connector-analog-tv",
.id = 0,
.dev.platform_data = &overo_tv_pdata,
};
static const struct display_timing overo_lcd43_videomode = {
.pixelclock = { 0, 9200000, 0 },
.hactive = { 0, 480, 0 },
.hfront_porch = { 0, 8, 0 },
.hback_porch = { 0, 4, 0 },
.hsync_len = { 0, 41, 0 },
.vactive = { 0, 272, 0 },
.vfront_porch = { 0, 4, 0 },
.vback_porch = { 0, 2, 0 },
.vsync_len = { 0, 10, 0 },
.flags = DISPLAY_FLAGS_HSYNC_LOW | DISPLAY_FLAGS_VSYNC_LOW |
DISPLAY_FLAGS_DE_HIGH | DISPLAY_FLAGS_PIXDATA_POSEDGE,
};
static struct panel_dpi_platform_data overo_lcd43_pdata = {
.name = "lcd43",
.source = "dpi.0",
.data_lines = 24,
.display_timing = &overo_lcd43_videomode,
.enable_gpio = OVERO_GPIO_LCD_EN,
.backlight_gpio = OVERO_GPIO_LCD_BL,
};
static struct platform_device overo_lcd43_device = {
.name = "panel-dpi",
.id = 0,
.dev.platform_data = &overo_lcd43_pdata,
};
static struct connector_dvi_platform_data overo_dvi_connector_pdata = {
.name = "dvi",
.source = "tfp410.0",
.i2c_bus_num = 3,
};
static struct platform_device overo_dvi_connector_device = {
.name = "connector-dvi",
.id = 0,
.dev.platform_data = &overo_dvi_connector_pdata,
};
static struct encoder_tfp410_platform_data overo_tfp410_pdata = {
.name = "tfp410.0",
.source = "dpi.0",
.data_lines = 24,
.power_down_gpio = -1,
};
static struct platform_device overo_tfp410_device = {
.name = "tfp410",
.id = 0,
.dev.platform_data = &overo_tfp410_pdata,
};
static struct omap_dss_board_info overo_dss_data = {
.default_display_name = "lcd43",
};
static void __init overo_display_init(void)
{
omap_display_init(&overo_dss_data);
if (!overo_use_lcd35)
platform_device_register(&overo_lcd43_device);
platform_device_register(&overo_tfp410_device);
platform_device_register(&overo_dvi_connector_device);
platform_device_register(&overo_tv_connector_device);
}
static struct mtd_partition overo_nand_partitions[] = {
{
.name = "xloader",
.offset = 0, /* Offset = 0x00000 */
.size = 4 * NAND_BLOCK_SIZE,
.mask_flags = MTD_WRITEABLE
},
{
.name = "uboot",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */
.size = 14 * NAND_BLOCK_SIZE,
},
{
.name = "uboot environment",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x240000 */
.size = 2 * NAND_BLOCK_SIZE,
},
{
.name = "linux",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x280000 */
.size = 32 * NAND_BLOCK_SIZE,
},
{
.name = "rootfs",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x680000 */
.size = MTDPART_SIZ_FULL,
},
};
static struct omap2_hsmmc_info mmc[] = {
{
.mmc = 1,
.caps = MMC_CAP_4_BIT_DATA,
.gpio_cd = -EINVAL,
.gpio_wp = -EINVAL,
},
{
.mmc = 2,
.caps = MMC_CAP_4_BIT_DATA,
.gpio_cd = -EINVAL,
.gpio_wp = -EINVAL,
.transceiver = true,
.ocr_mask = 0x00100000, /* 3.3V */
},
{} /* Terminator */
};
static struct regulator_consumer_supply overo_vmmc1_supply[] = {
REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
};
#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
#include <linux/leds.h>
static struct gpio_led gpio_leds[] = {
{
.name = "overo:red:gpio21",
.default_trigger = "heartbeat",
.gpio = 21,
.active_low = true,
},
{
.name = "overo:blue:gpio22",
.default_trigger = "none",
.gpio = 22,
.active_low = true,
},
{
.name = "overo:blue:COM",
.default_trigger = "mmc0",
.gpio = -EINVAL, /* gets replaced */
.active_low = true,
},
};
static struct gpio_led_platform_data gpio_leds_pdata = {
.leds = gpio_leds,
.num_leds = ARRAY_SIZE(gpio_leds),
};
static struct platform_device gpio_leds_device = {
.name = "leds-gpio",
.id = -1,
.dev = {
.platform_data = &gpio_leds_pdata,
},
};
static void __init overo_init_led(void)
{
platform_device_register(&gpio_leds_device);
}
#else
static inline void __init overo_init_led(void) { return; }
#endif
#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
#include <linux/input.h>
#include <linux/gpio_keys.h>
static struct gpio_keys_button gpio_buttons[] = {
{
.code = BTN_0,
.gpio = 23,
.desc = "button0",
.wakeup = 1,
},
{
.code = BTN_1,
.gpio = 14,
.desc = "button1",
.wakeup = 1,
},
};
static struct gpio_keys_platform_data gpio_keys_pdata = {
.buttons = gpio_buttons,
.nbuttons = ARRAY_SIZE(gpio_buttons),
};
static struct platform_device gpio_keys_device = {
.name = "gpio-keys",
.id = -1,
.dev = {
.platform_data = &gpio_keys_pdata,
},
};
static void __init overo_init_keys(void)
{
platform_device_register(&gpio_keys_device);
}
#else
static inline void __init overo_init_keys(void) { return; }
#endif
static int overo_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
#endif
return 0;
}
static struct twl4030_gpio_platform_data overo_gpio_data = {
.use_leds = true,
.setup = overo_twl_gpio_setup,
};
static struct regulator_init_data overo_vmmc1 = {
.constraints = {
.min_uV = 1850000,
.max_uV = 3150000,
.valid_modes_mask = REGULATOR_MODE_NORMAL
| REGULATOR_MODE_STANDBY,
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
| REGULATOR_CHANGE_MODE
| REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = ARRAY_SIZE(overo_vmmc1_supply),
.consumer_supplies = overo_vmmc1_supply,
};
static struct twl4030_platform_data overo_twldata = {
.gpio = &overo_gpio_data,
.vmmc1 = &overo_vmmc1,
};
static int __init overo_i2c_init(void)
{
omap3_pmic_get_config(&overo_twldata,
TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO,
TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
overo_twldata.vpll2->constraints.name = "VDVI";
omap3_pmic_init("tps65950", &overo_twldata);
/* i2c2 pins are used for gpio */
omap_register_i2c_bus(3, 400, NULL, 0);
return 0;
}
static struct panel_lb035q02_platform_data overo_lcd35_pdata = {
.name = "lcd35",
.source = "dpi.0",
.data_lines = 24,
.enable_gpio = OVERO_GPIO_LCD_EN,
.backlight_gpio = OVERO_GPIO_LCD_BL,
};
/*
* NOTE: We need to add either the lgphilips panel, or the lcd43 panel. The
* selection is done based on the overo_use_lcd35 field. If new SPI
* devices are added here, extra work is needed to make only the lgphilips panel
* affected by the overo_use_lcd35 field.
*/
static struct spi_board_info overo_spi_board_info[] __initdata = {
{
.modalias = "panel_lgphilips_lb035q02",
.bus_num = 1,
.chip_select = 1,
.max_speed_hz = 500000,
.mode = SPI_MODE_3,
.platform_data = &overo_lcd35_pdata,
},
};
static int __init overo_spi_init(void)
{
overo_ads7846_init();
if (overo_use_lcd35) {
spi_register_board_info(overo_spi_board_info,
ARRAY_SIZE(overo_spi_board_info));
}
return 0;
}
static struct usbhs_phy_data phy_data[] __initdata = {
{
.port = 2,
.reset_gpio = OVERO_GPIO_USBH_NRESET,
.vcc_gpio = -EINVAL,
},
};
static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
};
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#endif
static struct gpio overo_bt_gpios[] __initdata = {
{ OVERO_GPIO_BT_XGATE, GPIOF_OUT_INIT_LOW, "lcd enable" },
{ OVERO_GPIO_BT_NRESET, GPIOF_OUT_INIT_HIGH, "lcd bl enable" },
};
static struct regulator_consumer_supply dummy_supplies[] = {
REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
REGULATOR_SUPPLY("vddvario", "smsc911x.1"),
REGULATOR_SUPPLY("vdd33a", "smsc911x.1"),
};
static void __init overo_init(void)
{
int ret;
if (strstr(boot_command_line, "omapdss.def_disp=lcd35"))
overo_use_lcd35 = true;
regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
overo_i2c_init();
omap_hsmmc_init(mmc);
omap_serial_init();
omap_sdrc_init(mt46h32m32lf6_sdrc_params,
mt46h32m32lf6_sdrc_params);
board_nand_init(overo_nand_partitions,
ARRAY_SIZE(overo_nand_partitions), NAND_CS, 0, NULL);
usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
usb_musb_init(NULL);
usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
usbhs_init(&usbhs_bdata);
overo_spi_init();
overo_init_smsc911x();
overo_init_led();
overo_init_keys();
omap_twl4030_audio_init("overo", NULL);
overo_display_init();
/* Ensure SDRC pins are mux'd for self-refresh */
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
ret = gpio_request_one(OVERO_GPIO_W2W_NRESET, GPIOF_OUT_INIT_HIGH,
"OVERO_GPIO_W2W_NRESET");
if (ret == 0) {
gpio_export(OVERO_GPIO_W2W_NRESET, 0);
gpio_set_value(OVERO_GPIO_W2W_NRESET, 0);
udelay(10);
gpio_set_value(OVERO_GPIO_W2W_NRESET, 1);
} else {
pr_err("could not obtain gpio for OVERO_GPIO_W2W_NRESET\n");
}
ret = gpio_request_array(overo_bt_gpios, ARRAY_SIZE(overo_bt_gpios));
if (ret) {
pr_err("%s: could not obtain BT gpios\n", __func__);
} else {
gpio_export(OVERO_GPIO_BT_XGATE, 0);
gpio_export(OVERO_GPIO_BT_NRESET, 0);
gpio_set_value(OVERO_GPIO_BT_NRESET, 0);
mdelay(6);
gpio_set_value(OVERO_GPIO_BT_NRESET, 1);
}
ret = gpio_request_one(OVERO_GPIO_USBH_CPEN, GPIOF_OUT_INIT_HIGH,
"OVERO_GPIO_USBH_CPEN");
if (ret == 0)
gpio_export(OVERO_GPIO_USBH_CPEN, 0);
else
pr_err("could not obtain gpio for OVERO_GPIO_USBH_CPEN\n");
}
MACHINE_START(OVERO, "Gumstix Overo")
.atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = omap35xx_init_early,
.init_irq = omap3_init_irq,
.handle_irq = omap3_intc_handle_irq,
.init_machine = overo_init,
.init_late = omap35xx_init_late,
.init_time = omap3_sync32k_timer_init,
.restart = omap3xxx_restart,
MACHINE_END
Reference in New Issue View Git Blame Copy Permalink