forked from Minki/linux
0ff252c197
QCA61x4 chips have supported sleep feature using In-Band-Sleep commands to enable sleep feature based on H4 protocol. After sending patch/nvm configuration is done, IBS mode will be up and running Signed-off-by: Ben Young Tae Kim <ytkim@qca.qualcomm.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
42 lines
1.3 KiB
Makefile
42 lines
1.3 KiB
Makefile
#
|
|
# Makefile for the Linux Bluetooth HCI device drivers.
|
|
#
|
|
|
|
obj-$(CONFIG_BT_HCIVHCI) += hci_vhci.o
|
|
obj-$(CONFIG_BT_HCIUART) += hci_uart.o
|
|
obj-$(CONFIG_BT_HCIBCM203X) += bcm203x.o
|
|
obj-$(CONFIG_BT_HCIBPA10X) += bpa10x.o
|
|
obj-$(CONFIG_BT_HCIBFUSB) += bfusb.o
|
|
obj-$(CONFIG_BT_HCIDTL1) += dtl1_cs.o
|
|
obj-$(CONFIG_BT_HCIBT3C) += bt3c_cs.o
|
|
obj-$(CONFIG_BT_HCIBLUECARD) += bluecard_cs.o
|
|
obj-$(CONFIG_BT_HCIBTUART) += btuart_cs.o
|
|
|
|
obj-$(CONFIG_BT_HCIBTUSB) += btusb.o
|
|
obj-$(CONFIG_BT_HCIBTSDIO) += btsdio.o
|
|
|
|
obj-$(CONFIG_BT_INTEL) += btintel.o
|
|
obj-$(CONFIG_BT_ATH3K) += ath3k.o
|
|
obj-$(CONFIG_BT_MRVL) += btmrvl.o
|
|
obj-$(CONFIG_BT_MRVL_SDIO) += btmrvl_sdio.o
|
|
obj-$(CONFIG_BT_WILINK) += btwilink.o
|
|
obj-$(CONFIG_BT_BCM) += btbcm.o
|
|
obj-$(CONFIG_BT_RTL) += btrtl.o
|
|
obj-$(CONFIG_BT_QCA) += btqca.o
|
|
|
|
btmrvl-y := btmrvl_main.o
|
|
btmrvl-$(CONFIG_DEBUG_FS) += btmrvl_debugfs.o
|
|
|
|
hci_uart-y := hci_ldisc.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_H4) += hci_h4.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_BCSP) += hci_bcsp.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_LL) += hci_ll.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_ATH3K) += hci_ath.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_3WIRE) += hci_h5.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_INTEL) += hci_intel.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_BCM) += hci_bcm.o
|
|
hci_uart-$(CONFIG_BT_HCIUART_QCA) += hci_qca.o
|
|
hci_uart-objs := $(hci_uart-y)
|
|
|
|
ccflags-y += -D__CHECK_ENDIAN__
|