linux/arch/cris/Kconfig
Sam Ravnborg d5950b4355 [NET]: add a top-level Networking menu to *config
Create a new top-level menu named "Networking" thus moving
net related options and protocol selection way from the drivers
menu and up on the top-level where they belong.

To implement this all architectures has to source "net/Kconfig" before
drivers/*/Kconfig in their Kconfig file. This change has been
implemented for all architectures.

Device drivers for ordinary NIC's are still to be found
in the Device Drivers section, but Bluetooth, IrDA and ax25
are located with their corresponding menu entries under the new
networking menu item.

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-07-11 21:03:49 -07:00

185 lines
3.5 KiB
Plaintext

#
# For a description of the syntax of this configuration file,
# see the Configure script.
#
mainmenu "Linux/CRIS Kernel Configuration"
config MMU
bool
default y
config UID16
bool
default y
config RWSEM_GENERIC_SPINLOCK
bool
default y
config RWSEM_XCHGADD_ALGORITHM
bool
config GENERIC_CALIBRATE_DELAY
bool
default y
config CRIS
bool
default y
source "init/Kconfig"
menu "General setup"
source "fs/Kconfig.binfmt"
config ETRAX_CMDLINE
string "Kernel command line"
default "root=/dev/mtdblock3"
help
Pass additional commands to the kernel.
config ETRAX_WATCHDOG
bool "Enable ETRAX watchdog"
help
Enable the built-in watchdog timer support on ETRAX based embedded
network computers.
config ETRAX_WATCHDOG_NICE_DOGGY
bool "Disable watchdog during Oops printouts"
depends on ETRAX_WATCHDOG
help
By enabling this you make sure that the watchdog does not bite while
printing oopses. Recommended for development systems but not for
production releases.
config ETRAX_FAST_TIMER
bool "Enable ETRAX fast timer API"
help
This options enables the API to a fast timer implementation using
timer1 to get sub jiffie resolution timers (primarily one-shot
timers).
This is needed if CONFIG_ETRAX_SERIAL_FAST_TIMER is enabled.
config PREEMPT
bool "Preemptible Kernel"
help
This option reduces the latency of the kernel when reacting to
real-time or interactive events by allowing a low priority process to
be preempted even if it is in kernel mode executing a system call.
This allows applications to run more reliably even when the system is
under load.
Say Y here if you are building a kernel for a desktop, embedded
or real-time system. Say N if you are unsure.
source mm/Kconfig
endmenu
menu "Hardware setup"
choice
prompt "Processor type"
default ETRAX100LX
config ETRAX100LX
bool "ETRAX-100LX-v1"
help
Support version 1 of the ETRAX 100LX.
config ETRAX100LX_V2
bool "ETRAX-100LX-v2"
help
Support version 2 of the ETRAX 100LX.
config SVINTO_SIM
bool "ETRAX-100LX-for-xsim-simulator"
help
Support the xsim ETRAX Simulator.
endchoice
config ETRAX_ARCH_V10
bool
default y if ETRAX100LX || ETRAX100LX_V2
default n if !(ETRAX100LX || ETRAX100LX_V2)
config ETRAX_DRAM_SIZE
int "DRAM size (dec, in MB)"
default "8"
help
Size of DRAM (decimal in MB) typically 2, 8 or 16.
config ETRAX_FLASH_BUSWIDTH
int "Buswidth of flash in bytes"
default "2"
help
Width in bytes of the Flash bus (1, 2 or 4). Is usually 2.
source arch/cris/arch-v10/Kconfig
endmenu
source "net/Kconfig"
# bring in ETRAX built-in drivers
menu "Drivers for built-in interfaces"
source arch/cris/arch-v10/drivers/Kconfig
endmenu
source "drivers/base/Kconfig"
# standard linux drivers
source "drivers/mtd/Kconfig"
source "drivers/parport/Kconfig"
source "drivers/pnp/Kconfig"
source "drivers/block/Kconfig"
source "drivers/md/Kconfig"
source "drivers/ide/Kconfig"
source "drivers/scsi/Kconfig"
source "drivers/ieee1394/Kconfig"
source "drivers/message/i2o/Kconfig"
source "drivers/net/Kconfig"
source "drivers/isdn/Kconfig"
source "drivers/telephony/Kconfig"
source "drivers/cdrom/Kconfig"
#
# input before char - char/joystick depends on it. As does USB.
#
source "drivers/input/Kconfig"
source "drivers/char/Kconfig"
#source drivers/misc/Config.in
source "drivers/media/Kconfig"
source "fs/Kconfig"
source "sound/Kconfig"
source "drivers/usb/Kconfig"
source "arch/cris/Kconfig.debug"
source "security/Kconfig"
source "crypto/Kconfig"
source "lib/Kconfig"